Tegra194 and later support more than a single interrupt per bank. This
is primarily useful for virtualization but can also be helpful for more
fine-grained CPU affinity control. To keep things simple for now, route
all pins to the first interrupt.
For backwards-compatibility, support old device trees that specify only
one interrupt per bank by counting the interrupts at probe time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Newer chips support up to 8 interrupts per bank, which can be useful to
balance the load and decrease latency. However, it also required a very
complicated interrupt routing to be set up. To keep things simple for
now, ensure that a single interrupt per bank is enforced, even if all
possible interrupts are described in device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
The current hwirq is calculated based on the old GPIO pin order(input
GPIO range is from 0 to ngpios - 1).
It should be calculated based on the current GPIO input pin order(input
GPIOs are 0, 2, 4, ..., (ngpios - 1) * 2).
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Use helper functions to get private data from IRQ data instead of direct
access. No functional changes intended.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Use helper function to get IRQ hardware number instead of direct access.
No functional changes intended.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
The return type of irq_chip.irq_mask() and irq_chip.irq_unmask() should
be void.
Fixes: dbe776c2ca ("gpio: uniphier: add UniPhier GPIO controller driver")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Commit 8dcb7a15a5 ("gpiolib: acpi: Take into account debounce settings")
made the gpiolib-acpi code call gpio_set_debounce_timeout() when requesting
GPIOs.
This in itself is fine, but it also made gpio_set_debounce_timeout()
errors fatal, causing the requesting of the GPIO to fail. This is causing
regressions. E.g. on a HP ElitePad 1000 G2 various _AEI specified GPIO
ACPI event sources specify a debouncy timeout of 20 ms, but the
pinctrl-baytrail.c only supports certain fixed values, the closest
ones being 12 or 24 ms and pinctrl-baytrail.c responds with -EINVAL
when specified a value which is not one of the fixed values.
This is causing the acpi_request_own_gpiod() call to fail for 3
ACPI event sources on the HP ElitePad 1000 G2, which in turn is causing
e.g. the battery charging vs discharging status to never get updated,
even though a charger has been plugged-in or unplugged.
Make gpio_set_debounce_timeout() errors non fatal, warning about the
failure instead, to fix this regression.
Note we should probably also fix various pinctrl drivers to just
pick the first bigger discrete value rather then returning -EINVAL but
this will need to be done on a per driver basis, where as this fix
at least gets us back to where things were before and thus restores
functionality on devices where this was lost due to
gpio_set_debounce_timeout() errors.
Fixes: 8dcb7a15a5 ("gpiolib: acpi: Take into account debounce settings")
Depends-on: 2e2b496ceb ("gpiolib: acpi: Extract acpi_request_own_gpiod() helper")
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
By depending on devm_drm_panel_bridge_add(), devm_drm_of_get_bridge()
introduces a circular dependency between the modules drm (where
devm_drm_of_get_bridge() ends up) and drm_kms_helper (where
devm_drm_panel_bridge_add() is).
Fix this by moving devm_drm_of_get_bridge() to bridge/panel.c and thus
drm_kms_helper.
Fixes: 87ea95808d ("drm/bridge: Add a function to abstract away panels")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210917180925.2602266-1-maxime@cerno.tech
Currently, it is no longer possible to retrieve a DHCP address
on the imx6qdl-pico board.
This issue has been exposed by commit f5d9aa79df ("ARM: imx6q:
remove clk-out fixup for the Atheros AR8031 and AR8035 PHYs").
Fix it by describing the qca,clk-out-frequency property as suggested
by the commit above.
Fixes: 98670a0bb0 ("ARM: dts: imx6qdl: Add imx6qdl-pico support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The micro-SD card doesn't feature a write-protect pin. Set the
corresponding property in the devicetree to handle this behavior
correctly and suppress driver warnings.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
U-boot atempts to read serial alias value for ls1012a-rdb but couldn't
do so as it is not initialised and thus, FDT_ERR_NOTFOUND error is
reported while booting linux.
Loading fdt from FIT Image at a0000000 ...
Description: ls1012ardb-dtb
Type: Flat Device Tree
Data Start: 0xab111474
Data Size: 11285 Bytes = 11 KiB
Architecture: AArch64
Load Address: 0x90000000
Loading fdt from 0xab111474 to 0x90000000
Booting using the fdt blob at 0x90000000
Uncompressing Kernel Image
Loading Device Tree to 000000008fffa000, end 000000008ffffc14 ... OK
WARNING: fdt_fixup_stdout: could not read serial0 alias: FDT_ERR_NOTFOUND
NOTICE: RNG: INSTANTIATED
Starting kernel ...
Fix the above error by specifying serial value to duart.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reorder flexspi clock-names entry to make it compliant with bindings.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MIC2025 switch input signal nEN is active low, describe it as such
in the DT. The previous change to this regulator polarity was incorrectly
influenced by broken quirks in gpiolib-of.c, which is now long fixed. So
fix this regulator polarity setting here once and for all.
Fixes: 3c3601cd6a ("ARM: dts: imx53: Update USB configuration on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not very useful to have code which tries to report a rapidly
transient state which will not report anything majority of the time,
especially since it is currently only used from
<debugfs>/i915_gem_framebuffers.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210915114153.951670-1-tvrtko.ursulin@linux.intel.com
Drop the line-status conversion helper and do the conversion in place
instead.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that the driver is using usb_control_msg_recv(), the line status
handling can be simplified further by reading directly into the status
variable and doing the endian conversion in place.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the line-status handling by dropping redundant initialisations
and returning early on errors.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The note in c2adda27d2 ("video: backlight: Add of_find_backlight helper
in backlight.c") says that gpio-backlight uses brightness as power state.
This has been fixed since in ec665b756e ("backlight: gpio-backlight:
Correct initial power state handling") and other backlight drivers do not
require this workaround. Drop the workaround.
This fixes the case where e.g. pwm-backlight can perfectly well be set to
brightness 0 on boot in DT, which without this patch leads to the display
brightness to be max instead of off.
Fixes: c2adda27d2 ("video: backlight: Add of_find_backlight helper in backlight.c")
Cc: <stable@vger.kernel.org> # 5.4+
Cc: <stable@vger.kernel.org> # 4.19.x: ec665b756e: backlight: gpio-backlight: Correct initial power state handling
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This code has been dead since 2013, when the appleir driver was added by
commit 9a4a5574ce ("HID: appleir: add support for Apple ir devices"),
removing Apple IR receivers from this driver.
No other Apple devices use these quirks, so drop them.
Signed-off-by: Alexander F. Lent <lx@xanderlent.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the actual_length calculation is performed unsigned, packets
shorter than 7 bytes (e.g. packets without data or otherwise truncated)
or non-received packets ("zero" bytes) can cause buffer overflow.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214437
Fixes: 42337b9d4d958("HID: add driver for U2F Zero built-in LED and RNG")
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter's e-mail in MAINTAINERS is defunct:
This is the qmail-send program at a.mx.sunsite.dk.
<jacmet@sunsite.dk>:
Sorry, no mailbox here by that name. (#5.1.1)
Peter says:
** Ahh yes, it should be changed to peter@korsgaard.com.
However he also says:
** I haven't had access to c67x00 hw for quite some years though, so maybe
** it should be marked Orphan instead?
So change as he wishes.
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922063008.25758-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The panel already contains pinctrl-0 phandle, but it is missing
the default pinctrl-names property, so the pin configuration is
ignored. Fill in the missing pinctrl-names property, so the pin
configuration is applied.
Fixes: d81765d693 ("ARM: dts: imx53: Update LCD panel node on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No functional changes, but the ranges should be grouped by region.
Otherwise, schema dtbs_check would report the following errors.
"/linux-imx/arch/arm64/boot/dts/freescale/imx8mq-evk.dt.yaml: pcie@33800000: ranges: 'oneOf' conditional failed, one must be fixed:
/linux-imx/arch/arm64/boot/dts/freescale/imx8mq-evk.dt.yaml: pcie@33800000: ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 0, 536346624, 0, 65536, 2181038080, 0, 402653184, 402653184, 0, 133169152]] is not of type 'boolean'
True was expected
[[2164260864, 0, 0, 536346624, 0, 65536, 2181038080, 0, 402653184, 402653184, 0, 133169152]] is not of type 'null'
[2164260864, 0, 0, 536346624, 0, 65536, 2181038080, 0, 402653184, 402653184, 0, 133169152] is too long
From schema: //linux-imx/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml"
Refer to commit 281f1f99cf ("PCI: dwc: Detect number of iATU windows").
The num-viewport is not required anymore, remove them totally.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- ranges property should be grouped by region, with no functional
changes. Otherwise, schema dtbs_check would report the following errors.
"linux-imx/arch/arm/boot/dts/imx6qp-vicutp.dt.yaml: pcie@1ffc000: ranges: 'oneOf' conditional failed, one must be fixed:
linux-imx/arch/arm/boot/dts/imx6qp-vicutp.dt.yaml: pcie@1ffc000: ranges: 'oneOf' conditional failed, one must be fixed:
[[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640]] is not of type 'boolean'
True was expected
[[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640]] is not of type 'null'
[2164260864, 0, 0, 33030144, 0, 65536, 2181038080, 0, 16777216, 16777216, 0, 15728640] is too long
From schema: linux-imx/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml"
- refer to commit 281f1f99cf ("PCI: dwc: Detect number of iATU windows").
The num-viewport is not required anymore, remove them totally.
- dt_binding_check complains "compatible: ['fsl,imx6qp-pcie', 'snps,dw-pcie']
is too long", remove "snps,dw-pcie" from the compatible string.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I am the author of MediaTek SMI driver, and will to maintain
and develop it further.
Add myself to cover these items.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210914113703.31466-14-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
To improve the performance, We add some initial setting for smi larbs.
there are two part:
1), Each port has the special ostd(outstanding) value in each larb.
2), Two general settings for each larb.
a. THRT_UPDATE: the value in bits[7:4] of 0x24 is not so good.
The HW default is 4, and we expect it is 5, thus, add a flag to update
it. This is only a DE recommendatory value, not a actual issue.
The register name(THRT_CON) means: throttling control, and the field
RD_NU_LMT means: Read Non-ultra commands limit.
This change means update the Read non-ultra command from 4 to 5 here.
b. SW_FLAG: Set 1 to the FLAG register. this is only for helping
debug. We could confirm if the larb is reset from this value is 1 or 0.
In some SoC, this setting maybe changed dynamically for some special case
like 4K, and this initial setting is enough in mt8195.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210914113703.31466-13-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
To improve the performance, add initial setting for smi-common.
some register use some fix setting(suggested from DE).
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210914113703.31466-12-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
MT8195 has two smi-common, their IP are the same. Only the larbs that
connect with the smi-common are different. thus the bus_sel are different
for the two smi-common.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210914113703.31466-11-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
SMI sub common only have one output port. thus it has only one gals
clocks(gals0). then, smi-sub-common require the three clocks(apb/smi/gals0)
in has_gals case.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210914113703.31466-9-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
In mt8195, there are some larbs connect with the smi-sub-common, then
connect with smi-common.
Before we create device link between smi-larb with smi-common. If we have
sub-common, we should use device link the smi-larb and smi-sub-common,
then use device link between the smi-sub-common with smi-common. This is
for enabling clock/power automatically.
Move the device link code to a new interface for reusing.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210914113703.31466-8-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
No functional change. Only move the code position to make the code more
readable.
1. Put the register smi-common above smi-larb. Prepare to add some others
register setting.
2. Put mtk_smi_larb_unbind around larb_bind.
3. Sort the SoC data alphabetically. and put them in one line as the
current kernel allow it.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210914113703.31466-6-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Prepare for adding smi sub common. Only rename from smi_gen to smi_type.
No functional change.
About the current "smi_gen", we have gen1/gen2 that stand for the
generation number for HW. I plan to add a new type(sub_common), then the
name "gen" is not proper.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210914113703.31466-5-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Use clk_bulk interface instead of the orginal one to simplify the code.
For SMI larbs: Require apb/smi clocks while gals is optional.
For SMI common: Require apb/smi/gals0/gal1 in has_gals case. Otherwise,
also only require apb/smi, No optional clk here.
About the "has_gals" flag, for smi larbs, the gals clock also may be
optional even this platform support it. thus it always use
*_bulk_get_optional, then the flag has_gals is unnecessary. Remove it.
The smi_common's has_gals still keep it.
Also remove clk fail logs since bulk interface already output fail log.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210914113703.31466-4-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add the binding for smi-sub-common. The SMI block diagram like this:
IOMMU
| |
smi-common
------------------
| .... |
larb0 larb7 <-max is 8
The smi-common connects with smi-larb and IOMMU. The maximum larbs number
that connects with a smi-common is 8. If the engines number is over 8,
sometimes we use a smi-sub-common which is nearly same with smi-common.
It supports up to 8 input and 1 output(smi-common has 2 output)
Something like:
IOMMU
| |
smi-common
---------------------
| | ...
larb0 sub-common ... <-max is 8
-----------
| | ... <-max is 8 too.
larb2 larb5
We don't need extra SW setting for smi-sub-common, only the sub-common has
special clocks need to enable when the engines access dram.
If it is sub-common, it should have a "mediatek,smi" phandle to point to
its smi-common. meanwhile the sub-common only has one gals clock.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210914113703.31466-3-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add mt8195 smi supporting in the bindings.
In mt8195, there are two smi-common HW, one is for vdo(video output),
the other is for vpp(video processing pipe). They connect with different
smi-larbs, then some setting(bus_sel) is different. Differentiate them
with the compatible string.
Something like this:
IOMMU(VDO) IOMMU(VPP)
| |
SMI_COMMON_VDO SMI_COMMON_VPP
---------------- ----------------
| | ... | | ...
larb0 larb2 ... larb1 larb3 ...
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210914113703.31466-2-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
UAPI Changes:
Cross-subsystem Changes:
- dma-buf: Avoid a warning with some allocations, Remove
DMA_FENCE_TRACE macros
Core Changes:
- bridge: New helper to git rid of panels in drivers
- fence: Improve dma_fence_add_callback documentation, Improve
dma_fence_ops->wait documentation
- ioctl: Unexport drm_ioctl_permit
- lease: Documentation improvements
- fourcc: Add new macro to determine the modifier vendor
- quirks: Add the Steam Deck, Chuwi HiBook, Chuwi Hi10 Pro, Samsung
Galaxy Book 10.6, KD Kurio Smart C15200 2-in-1, Lenovo Ideapad D330
- resv: Improve the documentation
- shmem-helpers: Allocate WC pages on x86, Switch to vmf_insert_pfn
- sched: Fix for a timer being canceled too soon, Avoid null pointer
derefence if the fence is null in drm_sched_fence_free, Convert
drivers to rely on its dependency tracking
- ttm: Switch to kerneldoc, new helper to clear all DMA mappings, pool
shrinker optitimization, Remove ttm_tt_destroy_common, Fix for
unbinding on multiple drivers
Driver Changes:
- bochs: New PCI IDs
- msm: Fence ordering impromevemnts
- stm: Add layer alpha support, zpos
- v3d: Fix for a Vulkan CTS failure
- vc4: Conversion to the new bridge helpers
- vgem: Use shmem helpers
- virtio: Support mapping exported vram
- zte: Remove obsolete driver
- bridge: Probe improvements for it66121, enable DSI EOTP for anx7625,
errors propagation improvements for anx7625
- panels: 60fps mode for otm8009a, New driver for Samsung S6D27A1
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYULyqgAKCRDj7w1vZxhR
xVR1AP96dB3rfB0uIEvujMROBqupaKbYvP/7qilfMGIwLotDqQD/RKNB+EAaoHtT
hRA7zmz7kwYA/l8PihmF1zoFddX21gA=
=nFnK
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-09-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for $kernel-version:
UAPI Changes:
Cross-subsystem Changes:
- dma-buf: Avoid a warning with some allocations, Remove
DMA_FENCE_TRACE macros
Core Changes:
- bridge: New helper to git rid of panels in drivers
- fence: Improve dma_fence_add_callback documentation, Improve
dma_fence_ops->wait documentation
- ioctl: Unexport drm_ioctl_permit
- lease: Documentation improvements
- fourcc: Add new macro to determine the modifier vendor
- quirks: Add the Steam Deck, Chuwi HiBook, Chuwi Hi10 Pro, Samsung
Galaxy Book 10.6, KD Kurio Smart C15200 2-in-1, Lenovo Ideapad D330
- resv: Improve the documentation
- shmem-helpers: Allocate WC pages on x86, Switch to vmf_insert_pfn
- sched: Fix for a timer being canceled too soon, Avoid null pointer
derefence if the fence is null in drm_sched_fence_free, Convert
drivers to rely on its dependency tracking
- ttm: Switch to kerneldoc, new helper to clear all DMA mappings, pool
shrinker optitimization, Remove ttm_tt_destroy_common, Fix for
unbinding on multiple drivers
Driver Changes:
- bochs: New PCI IDs
- msm: Fence ordering impromevemnts
- stm: Add layer alpha support, zpos
- v3d: Fix for a Vulkan CTS failure
- vc4: Conversion to the new bridge helpers
- vgem: Use shmem helpers
- virtio: Support mapping exported vram
- zte: Remove obsolete driver
- bridge: Probe improvements for it66121, enable DSI EOTP for anx7625,
errors propagation improvements for anx7625
- panels: 60fps mode for otm8009a, New driver for Samsung S6D27A1
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 16 Sep 2021 17:30:50 AEST
# gpg: using EDDSA key 5C1337A45ECA9AEB89060E9EE3EF0D6F671851C5
# gpg: Can't check signature: No public key
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916073132.ptbbmjetm7v3ufq3@gilmour
According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
compatible = "arm,sp805", "arm,primecell";
The current compatible string doesn't exist at all. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ZII Ultra board uses the same design as the EVK board supplying
PCIE_VPH with 3.3V. Add this connection to the DT to allow the PCIe
driver to enable the internal PHY regulator, as required by the
reference manual.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SD card slot on the Reform 2 uses the card detect pad routed to
the uSDHC2 module as intended. This is currently working as it is the
default mux setting for this pad, but better be explicit and add it
to the pinctrl node.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Align the name of operating-points node to dtschema to fix warnings like:
ddrc-opp-table: $nodename:0: 'ddrc-opp-table' does not match '^opp-table(-[a-z0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Setting SCSI logging level with error=3, we saw some errors from enclosues:
[108017.360833] ses 0:0:9:0: tag#641 Done: NEEDS_RETRY Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[108017.360838] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427778] ses 0:0:9:0: Power-on or device reset occurred
[108017.427784] ses 0:0:9:0: tag#641 Done: SUCCESS Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[108017.427788] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427791] ses 0:0:9:0: tag#641 Sense Key : Unit Attention [current]
[108017.427793] ses 0:0:9:0: tag#641 Add. Sense: Bus device reset function occurred
[108017.427801] ses 0:0:9:0: Failed to get diagnostic page 0x1
[108017.427804] ses 0:0:9:0: Failed to bind enclosure -19
[108017.427895] ses 0:0:10:0: Attached Enclosure device
[108017.427942] ses 0:0:10:0: Attached scsi generic sg18 type 13
Retry if the Send/Receive Diagnostic commands complete with a transient
error status (NOT_READY or UNIT_ATTENTION with ASC 0x29).
Link: https://lore.kernel.org/r/1631849061-10210-2-git-send-email-wenxiong@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Reviewed-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Contention for the mailbox interface may occur during driver initialization
(immediately after a function reset), between mailbox commands initiated
via ioctl (bsg) and those driver requested by the driver.
After setting SLI_ACTIVE flag for a port, there is a window in which the
driver will allow an ioctl to be initiated while the adapter is
initializing and issuing mailbox commands via polling. The polling logic
then gets confused.
Correct by having thread setting SLI_ACTIVE spot an active mailbox command
and allow it complete before proceeding.
Link: https://lore.kernel.org/r/20210921143008.64212-1-jsmart2021@gmail.com
Co-developed-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
dc395x_init_one()->adapter_init() might fail. In this case, the acb is
already cleaned up by adapter_init(), no need to do that in
adapter_uninit(acb) again.
[ 1.252251] dc395x: adapter init failed
[ 1.254900] RIP: 0010:adapter_uninit+0x94/0x170 [dc395x]
[ 1.260307] Call Trace:
[ 1.260442] dc395x_init_one.cold+0x72a/0x9bb [dc395x]
Link: https://lore.kernel.org/r/20210907040702.1846409-1-ztong0001@gmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I fixed a stringop-overread warning earlier this year, now a second copy of
the original code was added and the warning came back:
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_cmf_info_show':
drivers/scsi/lpfc/lpfc_attr.c:289:25: error: 'strnlen' specified bound 4095 exceeds source size 24 [-Werror=stringop-overread]
289 | strnlen(LPFC_INFO_MORE_STR, PAGE_SIZE - 1),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it the same way as the other copy.
Link: https://lore.kernel.org/r/20210920095628.1191676-1-arnd@kernel.org
Fixes: ada48ba70f ("scsi: lpfc: Fix gcc -Wstringop-overread warning")
Fixes: 74a7baa2a3 ("scsi: lpfc: Add cmf_info sysfs entry")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The limit should be "PAGE_SIZE - len" instead of "PAGE_SIZE". We're not
going to hit the limit so this fix will not affect runtime.
Link: https://lore.kernel.org/r/20210916132331.GE25094@kili
Fixes: 5b9e70b22c ("scsi: lpfc: raise sg count for nvme to use available sg resources")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This scnprintf() uses the wrong limit. It should be
"LPFC_FPIN_WWPN_LINE_SZ - len" instead of LPFC_FPIN_WWPN_LINE_SZ.
Link: https://lore.kernel.org/r/20210916132251.GD25094@kili
Fixes: 428569e66f ("scsi: lpfc: Expand FPIN and RDF receive logging")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>