Commit graph

1,169,205 commits

Author SHA1 Message Date
AngeloGioacchino Del Regno
f8881c5d2f dt-bindings: soc: qcom: Add devicetree binding for QCOM SPM
Add devicetree binding for Qualcomm Subsystem Power Manager (SPM).

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210729155609.608159-3-angelogioacchino.delregno@somainline.org
2021-09-21 17:41:48 -05:00
AngeloGioacchino Del Regno
60f3692b5f cpuidle: qcom_spm: Detach state machine from main SPM handling
In commit a871be6b8e ("cpuidle: Convert Qualcomm SPM driver to a generic
CPUidle driver") the SPM driver has been converted to a
generic CPUidle driver: that was mainly made to simplify the
driver and that was a great accomplishment;
Though, at that time, this driver was only applicable to ARM 32-bit SoCs,
lacking logic about the handling of newer generation SAW.

In preparation for the enablement of SPM features on AArch64/ARM64,
split the cpuidle-qcom-spm driver in two: the CPUIdle related
state machine (currently used only on ARM SoCs) stays there, while
the SPM communication handling lands back in soc/qcom/spm.c and
also making sure to not discard the simplifications that were
introduced in the aforementioned commit.

Since now the "two drivers" are split, the SCM dependency in the
main SPM handling is gone and for this reason it was also possible
to move the SPM initialization early: this will also make sure that
whenever the SAW CPUIdle driver is getting initialized, the SPM
driver will be ready to do the job.

Please note that the anticipation of the SPM initialization was
also done to optimize the boot times on platforms that have their
CPU/L2 idle states managed by other means (such as PSCI), while
needing SAW initialization for other purposes, like AVS control.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210729155609.608159-2-angelogioacchino.delregno@somainline.org
2021-09-21 17:41:48 -05:00
Luca Weiss
b03543067a dt-bindings: firmware: scm: Add compatible for msm8226
Add devicetree compatible for SCM present in msm8226 platform.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210911232707.259615-4-luca@z3ntu.xyz
2021-09-21 17:41:48 -05:00
Bartosz Dudziak
7a010c3c64 arm: qcom: Add SMP support for MSM8226
Implement support for Cortex-A7 CPU release sequence in MSM8226 SoC.

Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210606201612.100752-3-bartosz.dudziak@snejp.pl
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-09-21 17:41:48 -05:00
Bartosz Dudziak
2b9575d478 dt-bindings: arm: Add SMP enable-method for MSM8226
Add binding in enable-method property for MSM8226 SoC SMP support.

Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210606201612.100752-2-bartosz.dudziak@snejp.pl
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-09-21 17:41:47 -05:00
Konrad Dybcio
1f7b2b6327 soc: qcom: llcc: Add configuration data for SM6350
Add LLCC configuration data for SM6350 SoC.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210820203105.229764-6-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-09-21 17:41:47 -05:00
Konrad Dybcio
c2b854b03a soc: qcom: rpmhpd: Add SM6350
Add the power domains exposed by RPMH in the Qualcomm SM6350 platform.

Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210820203105.229764-4-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-09-21 17:41:47 -05:00
Matthias Kaehlcke
be0416a3f9 arm64: dts: qcom: Add sc7180-trogdor-homestar
Homestar is a trogdor variant. The DT bits are essentially the same as
in the downstream tree, except for:

- skip -rev0 and rev1 which were early builds and have their issues,
  it's not very useful to support them upstream
- don't include the .dtsi for the MIPI cameras, which doesn't exist
  upstream

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909122053.1.Ieafda79b74f74a2b15ed86e181c06a3060706ec5@changeid
2021-09-21 17:37:06 -05:00
Robert Marko
63750607af arm64: dts: qcom: ipq8074: add SPMI bus
IPQ8074 uses SPMI for communication with the PMIC, so
since its already supported add the DT node for it.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210905165816.655275-1-robimarko@gmail.com
2021-09-21 17:37:06 -05:00
AngeloGioacchino Del Regno
17d32c10a2 arm64: dts: qcom: pmi8998: Add node for WLED
The PMI8998 PMIC has a WLED backlight controller, which is used on
most MSM8998 and SDM845 based devices: add a base configuration for
it and keep it disabled.

This contains only the PMIC specific configuration that does not
change across boards; parameters like number of strings, OVP and
current limits are product specific and shall be specified in the
product DT in order to achieve functionality.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123628.365968-1-angelogioacchino.delregno@somainline.org
2021-09-21 17:37:06 -05:00
Matthias Kaehlcke
b8d1e3d334 arm64: dts: qcom: sc7180-trogdor: Delete ADC config for unused thermistors
The charger thermistor on Lazor, CoachZ rev1 and Pompom rev1+2 is
either the wrong part or not stuffed at all, the same is true for
the skin temperature thermistor on CoachZ rev1. The corresponding
thermal zones are already disabled for these devices, in addition
delete the ADC nodes of the thermistors.

For Lazor and CoachZ rev1 also disable the PM6150 ADC and thermal
monitor since none of the ADC channels is used.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210903122212.v2.1.I9777d0036ecbb749a4fb9ebb892f94c6e3a51772@changeid
2021-09-21 17:37:06 -05:00
Robert Marko
d412786ab8 arm64: dts: qcom: ipq8074: remove USB tx-fifo-resize property
tx-fifo-resize is now added by default by the dwc3-qcom driver
to the SNPS DWC3 child node.

So, lets drop the tx-fifo-resize property from dwc3-qcom nodes
as having it there will cause the dwc3-qcom driver to error and
abort probe with:
[    1.362938] dwc3-qcom 8af8800.usb: unable to add property
[    1.368405] dwc3-qcom 8af8800.usb: failed to register DWC3 Core, err=-17

Fixes: cefdd52fa0 ("usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210902220325.1783567-1-robimarko@gmail.com
2021-09-21 17:37:06 -05:00
Douglas Anderson
82ea7d411d arm64: dts: qcom: sc7180: Base dynamic CPU power coefficients in reality
The sc7180's dynamic-power-coefficient violates the device tree bindings.
The bindings (arm/cpus.yaml) say that the units for the
dynamic-power-coefficient are supposed to be "uW/MHz/V^2". The ones for
sc7180 aren't this. Qualcomm arbitrarily picked 100 for the "little" CPUs
and then picked a number for the big CPU based on this.

At the time, there was a giant dicussion about this. Apparently Qualcomm
Engineers were instructed not to share the actual numbers here. As part
of the discussion, I pointed out [1] that these numbers shouldn't really
be secret since once a device is shipping anyone can just run a script
and produce them. This patch is the result of running the script I posted
in that discussion on sc7180-trogdor-coachz, which is currently available
for purchase by consumers.

[1] https://lore.kernel.org/r/CAD=FV=U1FP0e3_AVHpauUUZtD-5X3XCwh5aT9fH_8S_FFML2Uw@mail.gmail.com/

I ran the script four times, measuring little, big, little, big. I used
the 64-bit version of dhrystone 2.2 in my test. I got these results:

576 kHz, 596 mV, 20 mW, 88 Cx
768 kHz, 596 mV, 32 mW, 122 Cx
1017 kHz, 660 mV, 45 mW, 97 Cx
1248 kHz, 720 mV, 87 mW, 139 Cx
1324 kHz, 756 mV, 109 mW, 148 Cx
1516 kHz, 828 mV, 150 mW, 148 Cx
1612 kHz, 884 mV, 182 mW, 147 Cx
1708 kHz, 884 mV, 192 mW, 146 Cx
1804 kHz, 884 mV, 207 mW, 149 Cx
Your dynamic-power-coefficient for cpu 0: 132

825 kHz, 596 mV, 142 mW, 401 Cx
979 kHz, 628 mV, 183 mW, 427 Cx
1113 kHz, 656 mV, 224 mW, 433 Cx
1267 kHz, 688 mV, 282 mW, 449 Cx
1555 kHz, 812 mV, 475 mW, 450 Cx
1708 kHz, 828 mV, 566 mW, 478 Cx
1843 kHz, 884 mV, 692 mW, 476 Cx
1900 kHz, 884 mV, 722 mW, 482 Cx
1996 kHz, 916 mV, 814 mW, 482 Cx
2112 kHz, 916 mV, 862 mW, 483 Cx
2208 kHz, 916 mV, 962 mW, 521 Cx
2323 kHz, 940 mV, 1060 mW, 517 Cx
2400 kHz, 956 mV, 1133 mW, 518 Cx
Your dynamic-power-coefficient for cpu 6: 471

576 kHz, 596 mV, 26 mW, 103 Cx
768 kHz, 596 mV, 40 mW, 147 Cx
1017 kHz, 660 mV, 54 mW, 114 Cx
1248 kHz, 720 mV, 97 mW, 151 Cx
1324 kHz, 756 mV, 113 mW, 150 Cx
1516 kHz, 828 mV, 154 mW, 148 Cx
1612 kHz, 884 mV, 194 mW, 155 Cx
1708 kHz, 884 mV, 203 mW, 152 Cx
1804 kHz, 884 mV, 219 mW, 155 Cx
Your dynamic-power-coefficient for cpu 0: 142

825 kHz, 596 mV, 148 mW, 530 Cx
979 kHz, 628 mV, 189 mW, 475 Cx
1113 kHz, 656 mV, 230 mW, 461 Cx
1267 kHz, 688 mV, 287 mW, 466 Cx
1555 kHz, 812 mV, 469 mW, 445 Cx
1708 kHz, 828 mV, 567 mW, 480 Cx
1843 kHz, 884 mV, 699 mW, 482 Cx
1900 kHz, 884 mV, 719 mW, 480 Cx
1996 kHz, 916 mV, 814 mW, 484 Cx
2112 kHz, 916 mV, 861 mW, 483 Cx
2208 kHz, 916 mV, 963 mW, 522 Cx
2323 kHz, 940 mV, 1063 mW, 520 Cx
2400 kHz, 956 mV, 1135 mW, 519 Cx
Your dynamic-power-coefficient for cpu 6: 489

As you can see, the calculations aren't perfectly consistent but
roughly you could say about 480 for big and 137 for little.

The ratio between these numbers isn't quite the same as the ratio
between the two numbers that Qualcomm used. Perhaps this is because
Qualcomm measured something slightly different than the 64-bit version
of dhrystone 2.2 or perhaps it's because they fudged these numbers a
bit (and fudged the capacity-dmips-mhz). As per discussion [2], let's
use the numbers I came up with and also un-fudge
capacity-dmips-mhz. While unfudging capacity-dmips-mhz, let's scale it
so that bigs are 1024 which seems to be the common practice.

In general these numbers don't need to be perfectly exact. In fact,
they can't be since the CPU power depends a lot on what's being run on
the CPU and the big/little CPUs are each more or less efficient in
different operations. Historically running the 32-bit vs. 64-bit
versions of dhrystone produced notably different numbers, though I
didn't test this time.

We also need to scale all of the sustainable-power numbers by the same
amount. I scale ones related to the big CPUs by the adjustment I made
to the big dynamic-power-coefficient and the ones related to the
little CPUs by the adjustment I made to the little
dynamic-power-coefficient.

[2] https://lore.kernel.org/r/0a865b6e-be34-6371-f9f2-9913ee1c5608@codeaurora.org/

Fixes: 71f873169a ("arm64: dts: qcom: sc7180: Add dynamic CPU power coefficients")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210902145127.v2.1.I049b30065f3c715234b6303f55d72c059c8625eb@changeid
2021-09-21 17:37:06 -05:00
Raffaele Tranquillini
4ac46b3682 arm64: dts: qcom: msm8996: xiaomi-gemini: Add support for Xiaomi Mi 5
Add a device tree for Xiaomi Mi 5 (gemini).

Signed-off-by: Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901193214.250375-5-y.oudjana@protonmail.com
2021-09-21 17:37:06 -05:00
Yassine Oudjana
46680fe9ba arm64: dts: qcom: msm8996: Add support for the Xiaomi MSM8996 platform
There are 5 Xiaomi devices with the MSM8996 SoC:

 - Mi 5 (gemini): MSM8996 + PMI8994
 - Mi Note 2 (scorpio): MSM8996 Pro + PMI8996
 - Mi 5s (capricorn): MSM8996 Pro + PMI8996
 - Mi Mix (lithium): MSM8996 Pro + PMI8996
 - Mi 5s Plus (natrium): MSM8996 Pro + PMI8996

These devices share a common board design with only a few differences.
Add support for the common board, as well as support for the Mi Note 2.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901193214.250375-4-y.oudjana@protonmail.com
2021-09-21 17:37:06 -05:00
Yassine Oudjana
214faf07e3 arm64: dts: qcom: msm8996: Add blsp2_i2c3
Add a node for blsp2_i2c3 which is used for type-C port control chips
and speaker codecs on some devices.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901193214.250375-3-y.oudjana@protonmail.com
2021-09-21 17:37:06 -05:00
Yassine Oudjana
c57b4247fa arm64: dts: qcom: db820c: Move blsp1_uart2 pin states to msm8996.dtsi
Move blsp1_uart2_default and blsp1_uart2_sleep to the SoC device tree to
avoid duplicating them in other device trees.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901193214.250375-2-y.oudjana@protonmail.com
2021-09-21 17:37:05 -05:00
AngeloGioacchino Del Regno
87cd46d68a arm64: dts: qcom: msm8998: Configure Adreno GPU and related IOMMU
The MSM8998 SoC includes an Adreno 540.1 GPU, with a maximum frequency
of 710MHz. This GPU may or may not accept a ZAP shader, depending on
platform configuration, so adding a zap-shader node is left to the
board DT.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-5-angelogioacchino.delregno@somainline.org
2021-09-21 17:37:05 -05:00
AngeloGioacchino Del Regno
94117eb172 arm64: dts: qcom: msm8998: Move qfprom iospace to calibrated values
The QFPROM iospace was (erroneously, I believe) set to the uncalibrated
fuse start address, but every driver only needs - and will always only
need - only calibrated values.

Move the iospace forward to the calibrated values start to avoid
offsetting every fuse definition.
Obviously, the only defined fuse (qusb2_hstx_trim) was also fixed to
remove the offset, in order to comply with this change.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-4-angelogioacchino.delregno@somainline.org
2021-09-21 17:37:05 -05:00
AngeloGioacchino Del Regno
3f1dcaff64 arm64: dts: qcom: msm8998: Fix CPU/L2 idle state latency and residency
The entry/exit latency and minimum residency in state for the idle
states of MSM8998 were ..bad: first of all, for all of them the
timings were written for CPU sleep but the min-residency-us param
was miscalculated (supposedly, while porting this from downstream);
Then, the power collapse states are setting PC on both the CPU
cluster *and* the L2 cache, which have different timings: in the
specific case of L2 the times are higher so these ones should be
taken into account instead of the CPU ones.

This parameter misconfiguration was not giving particular issues
because on MSM8998 there was no CPU scaling at all, so cluster/L2
power collapse was rarely (if ever) hit.
When CPU scaling is enabled, though, the wrong timings will produce
SoC unstability shown to the user as random, apparently error-less,
sudden reboots and/or lockups.

This set of parameters are stabilizing the SoC when CPU scaling is
ON and when power collapse is frequently hit.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-3-angelogioacchino.delregno@somainline.org
2021-09-21 17:37:05 -05:00
AngeloGioacchino Del Regno
05ce21b544 arm64: dts: qcom: msm8998: Configure the multimedia subsystem iommu
In preparation for enabling various components of the multimedia
subsystem, write configuration for its related IOMMU.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-2-angelogioacchino.delregno@somainline.org
2021-09-21 17:37:05 -05:00
AngeloGioacchino Del Regno
c075a2e39d arm64: dts: qcom: msm8998: Configure the MultiMedia Clock Controller (MMCC)
The MSM8998 MMCC is supported and has a driver: configure it as a
preparation for a later enablement of multimedia nodes (mdp, venus
and others).

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-1-angelogioacchino.delregno@somainline.org
2021-09-21 17:37:05 -05:00
Deepak Kumar Singh
8c75d585b9 soc: qcom: aoss: Expose send for generic usecase
Not all upcoming usecases will have an interface to allow the aoss
driver to hook onto. Expose the send api and create a get function to
enable drivers to send their own messages to aoss.

Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Deepak Kumar Singh <deesin@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1630420228-31075-2-git-send-email-deesin@codeaurora.org
2021-09-21 17:31:18 -05:00
Chuck Lever
8847ecc927 NFSD: Optimize DRC bucket pruning
DRC bucket pruning is done by nfsd_cache_lookup(), which is part of
every NFSv2 and NFSv3 dispatch (ie, it's done while the client is
waiting).

I added a trace_printk() in prune_bucket() to see just how long
it takes to prune. Here are two ends of the spectrum:

 prune_bucket: Scanned 1 and freed 0 in 90 ns, 62 entries remaining
 prune_bucket: Scanned 2 and freed 1 in 716 ns, 63 entries remaining
...
 prune_bucket: Scanned 75 and freed 74 in 34149 ns, 1 entries remaining

Pruning latency is noticeable on fast transports with fast storage.
By noticeable, I mean that the latency measured here in the worst
case is the same order of magnitude as the round trip time for
cached server operations.

We could do something like moving expired entries to an expired list
and then free them later instead of freeing them right in
prune_bucket(). But simply limiting the number of entries that can
be pruned by a lookup is simple and retains more entries in the
cache, making the DRC somewhat more effective.

Comparison with a 70/30 fio 8KB 12 thread direct I/O test:

Before:

  write: IOPS=61.6k, BW=481MiB/s (505MB/s)(14.1GiB/30001msec); 0 zone resets

WRITE:
	1848726 ops (30%)
	avg bytes sent per op: 8340 avg bytes received per op: 136
	backlog wait: 0.635158 	RTT: 0.128525 	total execute time: 0.827242 (milliseconds)

After:

  write: IOPS=63.0k, BW=492MiB/s (516MB/s)(14.4GiB/30001msec); 0 zone resets

WRITE:
	1891144 ops (30%)
	avg bytes sent per op: 8340 avg bytes received per op: 136
	backlog wait: 0.616114 	RTT: 0.126842 	total execute time: 0.805348 (milliseconds)

Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2021-09-21 18:21:34 -04:00
J. Bruce Fields
dc451bbc6f nfs: reexport documentation
We've supported reexport for a while but documentation is limited.  This
is mainly a simplified version of the text I wrote for the linux-nfs
wiki at https://wiki.linux-nfs.org/wiki/index.php/NFS_re-export.

Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2021-09-21 17:51:47 -04:00
J. Bruce Fields
9b6e27d01a nfsd: don't alloc under spinlock in rpc_parse_scope_id
Dan Carpenter says:

  The patch d20c11d86d: "nfsd: Protect session creation and client
  confirm using client_lock" from Jul 30, 2014, leads to the following
  Smatch static checker warning:

        net/sunrpc/addr.c:178 rpc_parse_scope_id()
        warn: sleeping in atomic context

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d20c11d86d ("nfsd: Protect session creation and client...")
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
2021-09-21 17:51:47 -04:00
Christian Lamparter
477ffdbdf3 ARM: BCM53016: MR32: get mac-address from nvmem
The MAC-Address of the MR32's sole ethernet port is
located in offset 0x66 of the attached AT24C64 eeprom.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-09-21 14:20:14 -07:00
Christian Lamparter
6abc4ca5a2 ARM: BCM53016: Specify switch ports for Meraki MR32
the switch identifies itself as a BCM53012 (rev 5)...
This patch has been tested & verified on OpenWrt's
snapshot with Linux 5.10 (didn't test any older kernels).
The MR32 is able to "talk to the network" as before with
OpenWrt's SWITCHDEV b53 driver.

| b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 5
| libphy: dsa slave smi: probed
| b53-srab-switch 18007000.ethernet-switch poe (uninitialized):
|	PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL)
| b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB callbacks.
|	Please migrate to PHYLINK!
| DSA: tree 0 setup

Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-09-21 14:20:07 -07:00
Rafał Miłecki
6461282862 ARM: dts: BCM53573: Add Tenda AC9 switch ports
This router has 1 WAN and 4 LAN ports.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-09-21 14:19:50 -07:00
Rafał Miłecki
9fb90ae6ca ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch
BCM53573 family SoC have Ethernet switch connected to the first Ethernet
controller (accessible over MDIO).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-09-21 14:19:41 -07:00
Ben Widawsky
ed97afb533 cxl/pci: Disambiguate cxl_pci further from cxl_mem
Commit 21e9f76733 ("cxl: Rename mem to pci") introduced the cxl_pci
driver which had formerly been named cxl_mem. At the time, the goal was
to be as light touch as possible because there were other patches in
flight. Since things have settled now, and a new cxl_mem driver will be
introduced shortly, spend the LOC now to clean up the existing names.

While here, fix the kernel docs to explain the situation better after
the core rework that has already landed.

Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/20210913163324.1008564-4-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 14:18:49 -07:00
Ben Widawsky
fa9a7d2db6 Documentation/cxl: Add bus internal docs
Kernel docs are already present in this file, but nothing is instructed
to generate them. Address that.

Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/20210913163324.1008564-2-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 14:18:49 -07:00
Dan Williams
48667f6761 cxl/core: Split decoder setup into alloc + add
The kbuild robot reports:

    drivers/cxl/core/bus.c:516:1: warning: stack frame size (1032) exceeds
    limit (1024) in function 'devm_cxl_add_decoder'

It is also the case the devm_cxl_add_decoder() is unwieldy to use for
all the different decoder types. Fix the stack usage by splitting the
creation into alloc and add steps. This also allows for context
specific construction before adding.

With the split the caller is responsible for registering a devm callback
to trigger device_unregister() for the decoder rather than it being
implicit in the decoder registration. I.e. the routine that calls alloc
is responsible for calling put_device() if the "add" operation fails.

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/163225205828.3038145.6831131648369404859.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 14:09:34 -07:00
Dan Williams
7d3eb23c4c tools/testing/cxl: Introduce a mock memory device + driver
Introduce an emulated device-set plus driver to register CXL memory
devices, 'struct cxl_memdev' instances, in the mock cxl_test topology.
This enables the development of HDM Decoder (Host-managed Device Memory
Decoder) programming flow (region provisioning) in an environment that
can be updated alongside the kernel as it gains more functionality.

Whereas the cxl_pci module looks for CXL memory expanders on the 'pci'
bus, the cxl_mock_mem module attaches to CXL expanders on the platform
bus emitted by cxl_test.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116440099.2460985.10692549614409346604.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 14:09:34 -07:00
Dan Williams
49be6dd807 cxl/mbox: Move command definitions to common location
In preparation for cxl_test to mock responses to mailbox command
requests, move some definitions from core/mbox.c to cxlmem.h.

No functional changes intended.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116439547.2460985.10457111177103589574.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 14:09:34 -07:00
Dan Williams
a5c2580216 cxl/bus: Populate the target list at decoder create
As found by cxl_test, the implementation populated the target_list for
the single dport exceptional case, it missed populating the target_list
for the typical multi-dport case. Root decoders always know their target
list at the beginning of time, and even switch-level decoders should
have a target list of one or more zeros by default, depending on the
interleave-ways setting.

Walk the hosting port's dport list and populate based on the passed in
map.

Move devm_cxl_add_passthrough_decoder() out of line now that it does the
work of generating a target_map.

Before:
$ cat /sys/bus/cxl/devices/root2/decoder*/target_list
0

0

After:
$ cat /sys/bus/cxl/devices/root2/decoder*/target_list
0
0,1,2,3
0
0,1,2,3

Where root2 is a CXL topology root object generated by 'cxl_test'.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116439000.2460985.11713777051267946018.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 14:09:34 -07:00
Dan Williams
67dcdd4d3b tools/testing/cxl: Introduce a mocked-up CXL port hierarchy
Create an environment for CXL plumbing unit tests. Especially when it
comes to an algorithm for HDM Decoder (Host-managed Device Memory
Decoder) programming, the availability of an in-kernel-tree emulation
environment for CXL configuration complexity and corner cases speeds
development and deters regressions.

The approach taken mirrors what was done for tools/testing/nvdimm/. I.e.
an external module, cxl_test.ko built out of the tools/testing/cxl/
directory, provides mock implementations of kernel APIs and kernel
objects to simulate a real world device hierarchy.

One feedback for the tools/testing/nvdimm/ proposal was "why not do this
in QEMU?". In fact, the CXL development community has developed a QEMU
model for CXL [1]. However, there are a few blocking issues that keep
QEMU from being a tight fit for topology + provisioning unit tests:

1/ The QEMU community has yet to show interest in merging any of this
   support that has had patches on the list since November 2020. So,
   testing CXL to date involves building custom QEMU with out-of-tree
   patches.

2/ CXL mechanisms like cross-host-bridge interleave do not have a clear
   path to be emulated by QEMU without major infrastructure work. This
   is easier to achieve with the alloc_mock_res() approach taken in this
   patch to shortcut-define emulated system physical address ranges with
   interleave behavior.

The QEMU enabling has been critical to get the driver off the ground,
and may still move forward, but it does not address the ongoing needs of
a regression testing environment and test driven development.

This patch adds an ACPI CXL Platform definition with emulated CXL
multi-ported host-bridges. A follow on patch adds emulated memory
expander devices.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/20210202005948.241655-1-ben.widawsky@intel.com [1]
Link: https://lore.kernel.org/r/163164680798.2831381.838684634806668012.stgit@dwillia2-desk3.amr.corp.intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:47:10 -07:00
Dan Williams
2e52b6256b cxl/pmem: Add support for multiple nvdimm-bridge objects
In preparation for a mocked unit test environment for CXL objects, allow
for multiple unique nvdimm-bridge objects.

For now, just allow multiple bridges to be registered. Later, when there
are multiple present, further updates are needed to
cxl_find_nvdimm_bridge() to identify which bridge is associated with
which CXL hierarchy for nvdimm registration.

Note that this does change the kernel device-name for the bridge object.
User space should not have any attachment to the device name at this
point as it is still early days in the CXL driver development.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163164647007.2831228.2150246954620721526.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:47:10 -07:00
Dan Williams
60b8f17215 cxl/pmem: Translate NVDIMM label commands to CXL label commands
The LIBNVDIMM IOCTL UAPI calls back to the nvdimm-bus-provider to
translate the Linux command payload to the device native command format.
The LIBNVDIMM commands get-config-size, get-config-data, and
set-config-data, map to the CXL memory device commands device-identify,
get-lsa, and set-lsa. Recall that the label-storage-area (LSA) on an
NVDIMM device arranges for the provisioning of namespaces. Additionally
for CXL the LSA is used for provisioning regions as well.

The data from device-identify is already cached in the 'struct cxl_mem'
instance associated with @cxl_nvd, so that payload return is simply
crafted and no CXL command is issued. The conversion for get-lsa is
straightforward, but the conversion for set-lsa requires an allocation
to append the set-lsa header in front of the payload.

Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163122524923.2534512.9431316965424264864.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:47:09 -07:00
Dan Williams
12f3856ad4 cxl/mbox: Add exclusive kernel command support
The CXL_PMEM driver expects exclusive control of the label storage area
space. Similar to the LIBNVDIMM expectation that the label storage area
is only writable from userspace when the corresponding memory device is
not active in any region, the expectation is the native CXL_PCI UAPI
path is disabled while the cxl_nvdimm for a given cxl_memdev device is
active in LIBNVDIMM.

Add the ability to toggle the availability of a given command for the
UAPI path. Use that new capability to shutdown changes to partitions and
the label storage area while the cxl_nvdimm device is actively proxying
commands for LIBNVDIMM.

Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/163164579468.2830966.6980053377428474263.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:57 -07:00
Dan Williams
ff56ab9e16 cxl/mbox: Convert 'enabled_cmds' to DECLARE_BITMAP
Define enabled_cmds as an embedded member of 'struct cxl_mem' rather
than a pointer to another dynamic allocation.

As this leaves only one user of cxl_cmd_count, just open code it and
delete the helper.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116436415.2460985.10101824045493194813.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:57 -07:00
Dan Williams
5a2328f4e8 cxl/pci: Use module_pci_driver
Now that cxl_mem_{init,exit} no longer need to manage debugfs, switch
back to the smaller form of the boiler plate.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116435825.2460985.7201322215431441130.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:57 -07:00
Dan Williams
4faf31b434 cxl/mbox: Move mailbox and other non-PCI specific infrastructure to the core
Now that the internals of mailbox operations are abstracted from the PCI
specifics a bulk of infrastructure can move to the core.

The CXL_PMEM driver intends to proxy LIBNVDIMM UAPI and driver requests
to the equivalent functionality provided by the CXL hardware mailbox
interface. In support of that intent move the mailbox implementation to
a shared location for the CXL_PCI driver native IOCTL path and CXL_PMEM
nvdimm command proxy path to share.

A unit test framework seeks to implement a unit test backend transport
for mailbox commands to communicate mocked up payloads. It can reuse all
of the mailbox infrastructure minus the PCI specifics, so that also gets
moved to the core.

Finally with the mailbox infrastructure and ioctl handling being
transport generic there is no longer any need to pass file
file_operations to devm_cxl_add_memdev(). That allows all the ioctl
boilerplate to move into the core for unit test reuse.

No functional change intended, just code movement.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116435233.2460985.16197340449713287180.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:56 -07:00
Dan Williams
4cb35f1ca0 cxl/pci: Drop idr.h
Commit 3d135db510 ("cxl/core: Move memdev management to core") left
this straggling include for cxl_memdev setup. Clean it up.

Cc: Ben Widawsky <ben.widawsky@intel.com>
Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/163116434668.2460985.12264757586266849616.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:56 -07:00
Dan Williams
b64955a929 cxl/mbox: Introduce the mbox_send operation
In preparation for implementing a unit test backend transport for ioctl
operations, and making the mailbox available to the cxl/pmem
infrastructure, move the existing PCI specific portion of mailbox handling
to an "mbox_send" operation.

With this split all the PCI-specific transport details are comprehended
by a single operation and the rest of the mailbox infrastructure is
'struct cxl_mem' and 'struct cxl_memdev' generic.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/163116434098.2460985.9004760022659400540.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:56 -07:00
Dan Williams
13e7749d06 cxl/pci: Clean up cxl_mem_get_partition_info()
Commit 0b9159d0ff ("cxl/pci: Store memory capacity values") missed
updating the kernel-doc for 'struct cxl_mem' leading to the following
warnings:

./scripts/kernel-doc -v drivers/cxl/cxlmem.h 2>&1 | grep warn
drivers/cxl/cxlmem.h:107: warning: Function parameter or member 'total_bytes' not described in 'cxl_mem'
drivers/cxl/cxlmem.h:107: warning: Function parameter or member 'volatile_only_bytes' not described in 'cxl_mem'
drivers/cxl/cxlmem.h:107: warning: Function parameter or member 'persistent_only_bytes' not described in 'cxl_mem'
drivers/cxl/cxlmem.h:107: warning: Function parameter or member 'partition_align_bytes' not described in 'cxl_mem'
drivers/cxl/cxlmem.h:107: warning: Function parameter or member 'active_volatile_bytes' not described in 'cxl_mem'
drivers/cxl/cxlmem.h:107: warning: Function parameter or member 'active_persistent_bytes' not described in 'cxl_mem'
drivers/cxl/cxlmem.h:107: warning: Function parameter or member 'next_volatile_bytes' not described in 'cxl_mem'
drivers/cxl/cxlmem.h:107: warning: Function parameter or member 'next_persistent_bytes' not described in 'cxl_mem'

Also, it is redundant to describe those same parameters in the
kernel-doc for cxl_mem_get_partition_info(). Given the only user of that
routine updates the values in @cxlm, just do that implicitly internal to
the helper.

Cc: Ira Weiny <ira.weiny@intel.com>
Reported-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163157174216.2653013.1277706528753990974.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:56 -07:00
Dan Williams
99e222a5f1 cxl/pci: Make 'struct cxl_mem' device type generic
In preparation for adding a unit test provider of a cxl_memdev, convert
the 'struct cxl_mem' driver context to carry a generic device rather
than a pci device.

Note, some dev_dbg() lines needed extra reformatting per clang-format.

This conversion also allows the cxl_mem_create() and
devm_cxl_add_memdev() calling conventions to be simplified. The "host"
for a cxl_memdev, must be the same device for the driver that allocated
@cxlm.

Acked-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/163116432973.2460985.7553504957932024222.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:56 -07:00
Dan Williams
5af96835e4 libnvdimm/labels: Introduce CXL labels
Now that all of use sites of label data have been converted to nsl_*
helpers, introduce the CXL label format. The ->cxl flag in
nvdimm_drvdata indicates the label format the device expects. A
follow-on patch allows a bus provider to select the label style.

Note that the EFI definition of the labels represents the Linux "claim
class" with a GUID. The CXL definition of the labels stores the same
identifier in UUID byte order.

Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116432405.2460985.5547867384570123403.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:56 -07:00
Dan Williams
540ccaa2e4 libnvdimm/label: Define CXL region labels
Add a definition of the CXL 2.0 region label format. Note this is done
as a separate patch to make the next patch that adds namespace label
support easier to read.

Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116431893.2460985.4003511000574373922.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:56 -07:00
Dan Williams
999c993a85 libnvdimm/labels: Fix kernel-doc for label.h
Clean up existing kernel-doc warnings before adding new CXL label data
structures.

drivers/nvdimm/label.h:66: warning: Function parameter or member 'labelsize' not described in 'nd_namespace_index'
drivers/nvdimm/label.h:66: warning: Function parameter or member 'free' not described in 'nd_namespace_index'
drivers/nvdimm/label.h:103: warning: Function parameter or member 'align' not described in 'nd_namespace_label'
drivers/nvdimm/label.h:103: warning: Function parameter or member 'reserved' not described in 'nd_namespace_label'
drivers/nvdimm/label.h:103: warning: Function parameter or member 'type_guid' not described in 'nd_namespace_label'
drivers/nvdimm/label.h:103: warning: Function parameter or member 'abstraction_guid' not described in 'nd_namespace_label'
drivers/nvdimm/label.h:103: warning: Function parameter or member 'reserved2' not described in 'nd_namespace_label'
drivers/nvdimm/label.h:103: warning: Function parameter or member 'checksum' not described in 'nd_namespace_label'

Reported-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163116431381.2460985.6990754901097922099.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-09-21 13:44:55 -07:00