Commit graph

1,169,205 commits

Author SHA1 Message Date
Nicolas Dichtel
f8d858e607 xfrm: make user policy API complete
>From a userland POV, this API was based on some magic values:
 - dirmask and action were bitfields but meaning of bits
   (XFRM_POL_DEFAULT_*) are not exported;
 - action is confusing, if a bit is set, does it mean drop or accept?

Let's try to simplify this uapi by using explicit field and macros.

Fixes: 2d151d3907 ("xfrm: Add possibility to set the default to block if we have no policy")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2021-09-15 13:41:36 +02:00
Joonas Lahtinen
d5dd580deb Merge drm/drm-next into drm-intel-gt-next
Close the divergence which has caused patches not to apply and
have a solid baseline for the PXP patches that Rodrigo will send
a topic branch PR for.

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2021-09-15 13:23:27 +03:00
Owen Kirby
8c8b997c34 ARM: dts: at91: add Exegin Q5xR5 board
Add Exegin Q5xR5. The base device tree is from OpenWrt tree and with
the addition of this patch there will be no need to maintain it
separatelly in OpenWrt.

[osk: original author of patch in OpenWrt]
[claudiu.beznea: use "&<label> {" syntax, sorted nodes in alphabetical
 order, adapted flash to new support in kernel 5.14, use proper
 compatibles according to kernel 5.14, use macros instead of
 hardcoded numbers for pinctrl phandles and for all pinctrl references,
 add pinctrl-names, pinctrl-X where necessaray]

Signed-off-by: Owen Kirby <osk@exegin.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-8-claudiu.beznea@microchip.com
2021-09-15 12:21:15 +02:00
Claudiu Beznea
045ca26e42 dt-bindings: ARM: at91: document exegin q5xr5 board
Document Exegin Q5xR5 board.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-7-claudiu.beznea@microchip.com
2021-09-15 12:21:15 +02:00
Claudiu Beznea
3e1108bcce dt-bindings: add vendor prefix for exegin
Add vendor prefix for Exegin Technologies Limited.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-6-claudiu.beznea@microchip.com
2021-09-15 12:21:15 +02:00
Adam Porter
6dcb573a0a ARM: dts: at91: add CalAmp LMU5000 board
Add CalAmp LMU5000 board. The base device tree is from OpenWrt tree and
with the addition of this patch there will be no need to maintain it
separatelly in OpenWrt.

[porter.adam: original author of patch in OpenWrt]
[claudiu.beznea: fixed compilation warnings, use &<lable> syntax,
 sorted nodes in alphabetical order, adapted flash to new support
 in kernel 5.14, use proper compatibles according to kernel 5.14,
 use macros instead of hard coded numbers for pinctrl phandles and
 for all pinctrl references, add pinctrl-names, pinctrl-X where
 necessary]

Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-5-claudiu.beznea@microchip.com
2021-09-15 12:21:15 +02:00
Claudiu Beznea
1a492e3dae dt-bindings: ARM: at91: document CalAmp LMU5000 board
Document CalAmp LMU5000.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-4-claudiu.beznea@microchip.com
2021-09-15 12:16:45 +02:00
Claudiu Beznea
8bced0c5ff dt-bindings: add vendor prefix for calamp
Add vendor prefix for CalAmp Corp.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-3-claudiu.beznea@microchip.com
2021-09-15 12:16:45 +02:00
Claudiu Beznea
fcc090f9e3 ARM: dts: at91: at91sam9260: add pinctrl label
Add label for pinctrl node.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210816064416.1630674-2-claudiu.beznea@microchip.com
2021-09-15 12:16:45 +02:00
David S. Miller
c506cc5bc6 Merge branch 'ibmvnic-next'
Sukadev Bhattiprolu says:

====================
ibmvnic: Reuse ltb, rx, tx pools

It can take a long time to free and reallocate rx and tx pools and long
term buffer (LTB) during each reset of the VNIC. This is specially true
when the partition (LPAR) is heavily loaded and going through a Logical
Partition Migration (LPM). The long drawn reset causes the LPAR to lose
connectivity for extended periods of time and results in "RMC connection"
errors and the LPM failing.

What is worse is that during the LPM we could get a failover because
of the lost connectivity. At that point, the vnic driver releases
even the resources it has already allocated and starts over.

As long as the resources we have already allocated are valid/applicable,
we might as well hold on to them while trying to allocate the remaining
resources. This patch set attempts to reuse the resources previously
allocated as long as they are valid. It seems to vastly improve the
time taken for the vnic reset and signficantly reduces the chances of
getting the RMC connection errors. We do get still them occasionally,
but appears to be for reasons other than memory allocation delays and
those are still being investigated.

If the backing devices for a vnic adapter are not "matched" (see "pool
parameters" in patches 8 and 9) it is possible that we will still free
all the resources and allocate them. If that becomes a common problem,
we have to address it separately.

Thanks to input and extensive testing from Brian King, Cris Forno,
Dany Madden, Rick Lindsley.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:24 +01:00
Sukadev Bhattiprolu
bbd809305b ibmvnic: Reuse tx pools when possible
Rather than releasing the tx pools on every close and reallocating
them on open, reuse the tx pools unless the pool parameters (number
of pools, size of each pool or size of each buffer in a pool) have
changed.

If the pool parameters changed, then release the old pools (if
any) and allocate new ones.

Specifically release tx pools, if:
	- adapter is removed,
	- pool parameters change during reset,
	- we encounter an error when opening the adapter in response
	  to a user request (in ibmvnic_open()).

and don't release them:
	- in __ibmvnic_close() or
	- on errors in __ibmvnic_open()

in the hope that we can reuse them during this or next reset.

With these changes reset_tx_pools() can be dropped because its
optimization is now included in init_tx_pools() itself.

cleanup_tx_pools() releases all the skbs associated with the pool and
is called from ibmvnic_cleanup(), which is called on every reset. Since
we want to reuse skbs across resets, move cleanup_tx_pools() out of
ibmvnic_cleanup() and call it only when user closes the adapter.

Add two new adapter fields, ->prev_mtu, ->prev_tx_pool_size to track the
previous values and use them to decide whether to reuse or realloc the
pools.

Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:24 +01:00
Sukadev Bhattiprolu
489de956e7 ibmvnic: Reuse rx pools when possible
Rather than releasing the rx pools on and reallocating them on every
reset, reuse the rx pools unless the pool parameters (number of pools,
size of each pool or size of each buffer in a pool) have changed.

If the pool parameters changed, then release the old pools (if any)
and allocate new ones.

Specifically release rx pools, if:
	- adapter is removed,
	- pool parameters change during reset,
	- we encounter an error when opening the adapter in response
	  to a user request (in ibmvnic_open()).

and don't release them:
	- in __ibmvnic_close() or
	- on errors in __ibmvnic_open()

in the hope that we can reuse them on the next reset.

With these, reset_rx_pools() can be dropped because its optimzation is
now included in init_rx_pools() itself.

cleanup_rx_pools() releases all the skbs associated with the pool and
is called from ibmvnic_cleanup(), which is called on every reset. Since
we want to reuse skbs across resets, move cleanup_rx_pools() out of
ibmvnic_cleanup() and call it only when user closes the adapter.

Add two new adapter fields, ->prev_rx_buf_sz, ->prev_rx_pool_size to
keep track of the previous values and use them to decide whether to
reuse or realloc the pools.

Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:24 +01:00
Sukadev Bhattiprolu
f8ac0bfa7d ibmvnic: Reuse LTB when possible
Reuse the long term buffer during a reset as long as its size has
not changed. If the size has changed, free it and allocate a new
one of the appropriate size.

When we do this, alloc_long_term_buff() and reset_long_term_buff()
become identical. Drop reset_long_term_buff().

Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:24 +01:00
Sukadev Bhattiprolu
129854f061 ibmvnic: Use bitmap for LTB map_ids
In a follow-on patch, we will reuse long term buffers when possible.
When doing so we have to be careful to properly assign map ids. We
can no longer assign them sequentially because a lower map id may be
available and we could wrap at 255 and collide with an in-use map id.

Instead, use a bitmap to track active map ids and to find a free map id.
Don't need to take locks here since the map_id only changes during reset
and at that time only the reset worker thread should be using the adapter.

Noticed this when analyzing an error Dany Madden ran into with the
patch set.

Reported-by: Dany Madden <drt@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:24 +01:00
Sukadev Bhattiprolu
0d1af4fa71 ibmvnic: init_tx_pools move loop-invariant code
In init_tx_pools() move some loop-invariant code out of the loop.

Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:23 +01:00
Sukadev Bhattiprolu
8243c7ed6d ibmvnic: Use/rename local vars in init_tx_pools
Use/rename local variables in init_tx_pools() for consistency with
init_rx_pools() and for readability. Also add some comments

Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:23 +01:00
Sukadev Bhattiprolu
0df7b9ad8f ibmvnic: Use/rename local vars in init_rx_pools
To make the code more readable, use/rename some local variables.
Basically we have a set of pools, num_pools. Each pool has a set of
buffers, pool_size and each buffer is of size buff_size.

pool_size is a bit ambiguous (whether size in bytes or buffers). Add
a comment in the header file to make it explicit.

Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:23 +01:00
Sukadev Bhattiprolu
0f2bf3188c ibmvnic: Fix up some comments and messages
Add/update some comments/function headers and fix up some messages.

Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:23 +01:00
Sukadev Bhattiprolu
38106b2c43 ibmvnic: Consolidate code in replenish_rx_pool()
For better readability, consolidate related code in replenish_rx_pool()
and add some comments.

Reviewed-by: Rick Lindsley <ricklind@linux.vnet.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:12:23 +01:00
David S. Miller
923990f643 Merge branch 'ptp-ocp-timecard-v13-fw'
Jonathan Lemon says:

====================
timecard updates for v13 firmware

This update mainly deals with features for the TimeCard v13 firmware.

The signals provided from the external SMA connectors can be steered
to different locations, and the generated SMA signals can be chosen.

Future timecard revisions will allow selectable I/O on any of the
SMA connectors, so name the attributes appropriately, and set up
the ABI in preparation for the new features.

The update also adds support for IRIG-B and DCF formats, as well
as NMEA output.

A ts_window_adjust tunable is also provided to fine-tune the
PHC:SYS time mapping.
--
v1: Earlier reviewed series was for v10 firmware, this is expanded to
    include the v13 features.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
d7050a2b85 docs: ABI: Add sysfs documentation for timecard
This patch describes the sysfs interface implemented by the
ptp_ocp driver, under /sys/class/timecard.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
1acffc6e09 ptp: ocp: Add timestamp window adjustment
The following process is used to read the PHC clock and correlate
the reading with the "correct" system time.

- get starting timestamp
- issue PCI write command
- issue PCI read command
- get ending timestamp
- read latched sec/nsec registers

The write command is posted to PCI bus and returns.  When the write
arrives at the FPGA, the PHC time is latched into the sec/nsec registers,
and a flag is set indicating the registers are valid.  The read command
returns this flag, and the time retrieval proceeds.

Below is a non-scaled picture of the timing diagram involved.  The
PHC time corresponds to some SYS time between [start, end].  Userspace
usually uses the midpoint between [start, end] to estimate the PCI
delay and match this with the PHC time.

 [start] |                |
   write |-------+        |
	 |        \       |
    read |----+    +----->|
	 |     \          * PHC time latched into register
	 |      \         |
midpoint |       +------->|
	 |                |
	 |                |
	 |           +----|
	 |          /     |
	 |<--------+      |
   [end] |                |

As the diagram indicates, the PHC time is latched before the midpoint,
so the system clock time is slightly off the real PHC time.  This shows
up as a phase error with an oscilliscope.

The workaround here is to provide a tunable which reduces (shrinks)
the end time in the above diagram.  This in turn moves the calculated
midpoint so the system time and PHC time are in agreemment.

Currently, the adjustment reduces the end time by 3/16th of the entire
window.  E.g.:  [start, end] ==> [start, (end - (3/16 * end)], which
produces reasonably good results.

Also reduce delays by just writing to the clock control register
instead of performing a read/modify/write sequence, as the contents
of the control register are known.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
6d59d4fa17 ptp: ocp: Have FPGA fold in ns adjustment for adjtime.
The current implementation of adjtime uses gettime/settime to
perform nanosecond adjustments.  This introduces addtional phase
errors due to delays.

Instead, use the FPGA's ability to just apply the nanosecond
adjustment to the clock directly.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
a62a56d04e ptp: ocp: Enable 4th timestamper / PPS generator
A 4th timestamper is added which timestamps the output of the PHC.

The clock nanosecond offset is not always zero, so when compared
to other timestampers, this provides precise measurements.

Also, the timestamper interrupt from the PHC can be used to generate
a PPS signal for /dev/pps.

Also allow PTP_CLK_REQ_PEROUT requests for a 1PPS output, but do
not actually configure any output pins, this is done via sysfs.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
71d7e08504 ptp: ocp: Add second GNSS device
Upcoming boards may have a second GNSS receiver, getting information
from a different constellation than the first receiver, which provides
some measure of anti-spoofing.

Expose the sysfs attribute for this device, if detected.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
e3516bb450 ptp: ocp: Add NMEA output
The timecard can provide a NMEA-1083 ZDA (time and date) output
string on a serial port, which can be used to drive other devices.

Add the NMEA resources, and the serial port as a sysfs attribute.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
f67bf662d2 ptp: ocp: Add debugfs entry for timecard
Provide a view into the timecard internals for debugging.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
065efcc5e9 ptp: ocp: Separate the init and info logic
On startup, parts of the FPGA need to be initialized - break these
out into their own functions, separate from the purely informational
blocks.

On startup, distrbute the UTC:TAI offset from the NMEA GNSS parser,
if it is available.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
89260d8782 ptp: ocp: Add sysfs attribute utc_tai_offset
IRIG and DCF output time in UTC, but the timecard operates
on TAI internally.  Add an attribute node which allows adding
an offset to these modes before output.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
d14ee2525d ptp: ocp: Add IRIG-B output mode control
IRIG-B has several different output formats, the timecard defaults
to using B007.  Add a control which selects different output modes.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:01 +01:00
Jonathan Lemon
6baf292542 ptp: ocp: Add IRIG-B and DCF blocks
IRIG (Inter-range Instrumentation Group) timecode format on
one of the SMA output channels is provided by the IRIG master
FPGA block.  Enable the master when the IRIG output format is
selected on either one of the output channels.

By default, the output is in B007 format.

DCF output format is provided by the DCF master block.

Also enable the IRIG and DCF slaves, which parse an incoming
signal from the external SMA connectors, and may be used to
adjust the PHC.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:00 +01:00
Jonathan Lemon
e1daf0ec73 ptp: ocp: Add SMA selector and controls
The latest firmware for the TimeCard adds selectable signals for
the SMA input/outputs.  Add support for SMA selectors, and the
GPIO controls needed for steering signals.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:00 +01:00
Jonathan Lemon
dcf614692c ptp: ocp: Add third timestamper
The firmware may provide a third signal timestamper, so make it
available for use.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:00 +01:00
Jonathan Lemon
bceff2905e ptp: ocp: Report error if resource registration fails.
If a resource could not be registered, report the name of
the resource and the error code.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:00 +01:00
Jonathan Lemon
56ec44033c ptp: ocp: Skip resources with out of range irqs
The TimeCard exposes different resources, which may have their
own irqs.  Space for the irqs is allocated through a MSI or MSI-X
interrupt vector.  On some platforms, the interrupt allocation
fails.

Rather than making this fatal, just skip exposing those resources.

The main timecard functionality (that of a PTP clock) will work
without the additional resources.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:00 +01:00
Jonathan Lemon
1447149d65 ptp: ocp: Skip I2C flash read when there is no controller.
If an I2C controller isn't present, don't try and read the I2C flash.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:00 +01:00
Jonathan Lemon
498ad3f438 ptp: ocp: Parameterize the TOD information display.
Only display the TOD information if there is a corresponding
TOD resource.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:00 +01:00
Jonathan Lemon
1618df6afa ptp: ocp: parameterize the i2c driver used
Move the xilinx i2c driver parameters to the resource block instead
of hardcoding things in the registration functions.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:10:00 +01:00
Aleksander Jan Bajkowski
c688721464 dt-bindings: net: lantiq: Add the burst length properties
The new added properties are used for configuring burst length.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:02:01 +01:00
Aleksander Jan Bajkowski
dac0bad937 dt-bindings: net: lantiq,etop-xway: Document Lantiq Xway ETOP bindings
Document the Lantiq Xway SoC series External Bus Unit (ETOP) bindings.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:02:01 +01:00
Aleksander Jan Bajkowski
5535bcfa72 dt-bindings: net: lantiq-xrx200-net: convert to the json-schema
Convert the Lantiq PMAC Device Tree binding documentation to json-schema.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:02:01 +01:00
Aleksander Jan Bajkowski
14d4e308e0 net: lantiq: configure the burst length in ethernet drivers
Configure the burst length in Ethernet drivers. This improves
Ethernet performance by 58%. According to the vendor BSP,
8W burst length is supported by ar9 and newer SoCs.

The NAT benchmark results on xRX200 (Down/Up):
* 2W: 330 Mb/s
* 4W: 432 Mb/s    372 Mb/s
* 8W: 520 Mb/s    389 Mb/s

Tested on xRX200 and xRX330.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:02:01 +01:00
Aleksander Jan Bajkowski
49293bbc50 MIPS: lantiq: dma: make the burst length configurable by the drivers
Make the burst length configurable by the drivers.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:02:01 +01:00
Aleksander Jan Bajkowski
5ad74d39c5 MIPS: lantiq: dma: fix burst length for DEU
The current definition of 2W burst length is invalid.
This patch fixes it. Current downstream DEU driver doesn't
use DMA. An incorrect burst length value doesn't cause any
errors. This patch also adds other burst length values.

Fixes: dfec1a827d ("MIPS: Lantiq: Add DMA support")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:02:01 +01:00
Aleksander Jan Bajkowski
5ca9ce2ba4 MIPS: lantiq: dma: reset correct number of channel
Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.

We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:02:01 +01:00
Aleksander Jan Bajkowski
c12aa581f6 MIPS: lantiq: dma: add small delay after reset
Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-15 11:02:01 +01:00
Durai Manickam KR
6a1ca035d2 ARM: dts: at91-sama5d27_som1_ek: Added I2C bus recovery support
SDA and SCL is configured as GPIO for I2C bus to recover during
I2C bus malfunction.

Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210914052113.85695-1-durai.manickamkr@microchip.com
2021-09-15 11:01:06 +02:00
Eugen Hristev
6b97032b9c ARM: dts: at91: sama7g5ek: enable ADC on the board
The ADC controller on the board is fed by a 2.5V reference voltage.
By default the channels #14 and #15 are dedicated to analog input
(marked AN on the board), on the connectors mikrobus1 and mikrobus2.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-11-eugen.hristev@microchip.com
2021-09-15 10:35:29 +02:00
Eugen Hristev
c7472302df ARM: dts: at91: sama7g5: add node for the ADC
Add node for the ADC controller in sama7g5 SoC.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-10-eugen.hristev@microchip.com
2021-09-15 10:35:29 +02:00
Eugen Hristev
2c9987f2ed ARM: dts: at91: sama5d27_wlsom1: add wifi device
SAMA5D27 WLSOM1 boards has a WILC3000 device soldered. Add proper
device tree nodes for this.

[eugen.hristev: original author of this code]
[claudiu.beznea: adapt such that make dtbs_check is happy, remove status
 for wifi_pwrseq and wifi nodes]

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[nicolas.ferre: original author of this code]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210825094055.642941-1-claudiu.beznea@microchip.com
2021-09-15 10:28:22 +02:00