This patch enables eth0 10G interface on CN9130-DB paltforms and
eth0 10G and eth3 10G interfaces on CN9131-DB.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The CN913x DB with topology B is similar to a regular setup (A)
boards, but uses NAND flash as a boot device, while topology A
boards are booting from SPI flash.
Since NAND and SPI on CN913x DB boards share some wires, they
cannot be activated simultaneously.
The DTS files for setup "B" are based on setup "A", in which the
CP0 NAND controller enabled and CP0 SPI1 disabled.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
nft_nat reports a bogus EAFNOSUPPORT if no layer 3 information is specified.
Fixes: d07db9884a ("netfilter: nf_tables: introduce nft_validate_register_load()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In case the entry is evicted via garbage collection there is
delay between the timeout value and the eviction event.
This adjusts the stop value based on how much time has passed.
Fixes: b87a2f9199 ("netfilter: conntrack: add gc worker to remove timed-out entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The flowtable follows the same timeout approach as conntrack, use the
same idiom as in cc16921351 ("netfilter: conntrack: avoid same-timeout
update") but also include the fix provided by e37542ba11 ("netfilter:
conntrack: avoid possible false sharing").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows the controller to suspend after a short period of
inactivity.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For chips that doesn't reset on suspend, we need to provide the correct
value of flow_control when it resumes. Therefore, store the flow
control value when reading from the config file to be reused upon
suspend.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some RTL chips resets the FW on suspend, so wakeup is disabled on
those chips. This patch introduces this WAKEUP_DISABLE flag so that
chips that doesn't reset FW on suspend can leave the flag unset and
is allowed to wake the host.
This patch also left RTL8822 WAKEUP_DISABLE flag unset, therefore
allowing it to wake the host, and preventing reprobing on resume.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With W=1 build, the compiler throws warning message as below:
security/integrity/ima/ima_mok.c:24:12: warning:
no previous prototype for ‘ima_mok_init’ [-Wmissing-prototypes]
__init int ima_mok_init(void)
Silence the warning by adding static keyword to ima_mok_init().
Signed-off-by: Austin Kim <austin.kim@lge.com>
Fixes: 41c89b64d7 ("IMA: create machine owner and blacklist keyrings")
Cc: stable@vger.kernel.org
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
New KMS properties come with a bunch of requirements to avoid each
driver from running their own, inconsistent, set of properties,
eventually leading to issues like property conflicts, inconsistencies
between drivers and semantics, etc.
Let's document what we expect.
Acked-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720143544.571760-1-maxime@cerno.tech
We do a bforget and return for no journal case, so let's remove this
conflict comment.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Guoqing Jiang <jiangguoqing@kylinos.cn>
Link: https://lore.kernel.org/r/20210714055940.1553705-1-guoqing.jiang@linux.dev
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
if (!ext4_has_feature_mmp(sb)) then retval can be unitialized before
we jump to the wait_to_exit label.
Fixes: 61bb4a1c41 ("ext4: fix possible UAF when remounting r/o a mmp-protected file system")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210713022728.2533770-1-yebin10@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Convert the rockchip,rk3399-cru binding to DT schema format.
Tested with
ARCH=arm64 make dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.yaml
ARCH=arm64 make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.yaml
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610175613.167601-1-nfraprado@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
simplify function Hal_GetChnlGroup8723B(). It returns
an unused and unnecessary bool value telling which
band the device works on. Since we work only on
2.4Ghz band and the useful return value is the
second function argument we convert the return type to
void.
remove 5Ghz dead code either (for channel > 14).
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/a5536788004c44fe819c0eab0d19504824af46cd.1626874164.git.fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set a condition for the message of "Couldn't set OPP regulators" to not
display if the error code is EPROBE_DEFER. Note that I used an if
statement to capture the condition instead of the dev_err_probe
function because I didn't want to change the DRM_DEV_ERROR usage.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721214830.25690-1-macroalpha82@gmail.com
The CPU domain should be static for discrete, and on DG1 we don't need
any flushing since everything is already coherent, so really all this
does is an object wait, for which we have an ioctl. Longer term the
desired caching should be an immutable creation time property for the
BO, which can be set with something like gem_create_ext.
One other user is iris + userptr, which uses the set_domain to probe all
the pages to check if the GUP succeeds, however we now have a PROBE
flag for this purpose.
v2: add some more kernel doc, also add the implicit rules with caching
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jordan Justen <jordan.l.justen@intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Kenneth Graunke <kenneth@whitecape.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715101536.2606307-5-matthew.auld@intel.com
Since drivers/mmc/host/sdhci-xenon.c declares the PROBE_PREFER_ASYNCHRONOUS
probe type, it is not guaranteed whether /dev/mmcblk0 will belong to
sdhci0 or sdhci1. In turn, this will break booting by:
root=/dev/mmcblk0p1
Fix the issue by adding aliases so that the old MMC controller indices
are preserved.
Fixes: 7320915c88 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enabling the PINCTRL_SM8350 symbol without GPIOLIB or SCM causes a build
failure:
WARNING: unmet direct dependencies detected for PINCTRL_MSM
Depends on [m]: PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && (QCOM_SCM [=m] || !QCOM_SCM [=m])
Selected by [y]:
- PINCTRL_SM8350 [=y] && PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && OF [=y]
aarch64-linux-ld: drivers/pinctrl/qcom/pinctrl-msm.o: in function `msm_gpio_irq_set_type':
pinctrl-msm.c:(.text.msm_gpio_irq_set_type+0x1c8): undefined reference to `qcom_scm_io_readl'
The main problem here is the 'select PINCTRL_MSM', which needs to be a
'depends on' as it is for all the other front-ends. As the GPIOLIB
dependency is now implied by that, symbol, remove the duplicate
dependencies in the process.
Fixes: d5d348a327 ("pinctrl: qcom: Add SM8350 pinctrl driver")
Fixes: 376f9e34c1 ("drivers: pinctrl: qcom: fix Kconfig dependency on GPIOLIB")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210723091400.1669716-1-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we exceed the limit of BSS entries, this function will free the
new entry, however, at this time, it is the last door to access the
inputed ies, so these ies will be unreferenced objects and cause memory
leak.
Therefore we should free its ies before deallocating the new entry, beside
of dropping it from hidden_list.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210628132334.851095-1-phind.uet@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In non-split data, we shouldn't be adding S1G and 6 GHz
data (or future bands) since we're really close to the
4k message size limit. Remove those bands, any modern
userspace that can use S1G or 6 GHz should already be
using split dumps, and if not then it needs to update.
Link: https://lore.kernel.org/r/20210712215329.31444162a2c2.I5555312e4a074c84f8b4e7ad79dc4d1fbfc5126c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Notify the driver about the 4-address mode change and also send a nulldata
packet to the AP to notify it about the change
Fixes: 1ff4e8f2de ("mac80211: notify the driver when a sta uses 4-address mode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210702050111.47546-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The logic for starting aggregation sessions was recently moved from minstrel_ht
to mac80211, into the subif tx handler just after the sta lookup.
Unfortunately this didn't work for mesh interfaces, since the sta lookup is
deferred until a much later point in time on those.
Fix this by also calling the aggregation check right after the deferred sta
lookup.
Fixes: 08a46c6420 ("mac80211: move A-MPDU session check from minstrel_ht to mac80211")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210629112853.29785-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a monitor interface is present together with other interfaces, a
received skb is copied and received on the monitor netdev. Before, the
copied skb was allocated with exactly the amount of space needed for
the radiotap header, resulting in an skb without any headroom at all
being received on the monitor netdev. With the introduction of eBPF
and XDP in the kernel, skbs may be processed by custom eBPF programs.
However, since the skb cannot be reallocated in the eBPF program, no
more data or headers can be pushed. The old code made sure the final
headroom was zero regardless of the value of NET_SKB_PAD, so increasing
that constant would have no effect.
Now we allocate monitor skb copies with a headroom of NET_SKB_PAD bytes
before the radiotap header. Monitor interfaces now behave in the same
way as other netdev interfaces that honor the NET_SKB_PAD constant.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210628123713.2070753-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pinctrl_power_button/pinctrl_power_out each define single GPIO
pinmux, except it is exactly the other one than the matching gpio-keys
and gpio-poweroff DT nodes use for that functionality. Swap the two
GPIOs to correct this error.
Fixes: 50d29fdb76 ("ARM: dts: imx53: Add power GPIOs on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec85365 ("ARM: imx: add missing clk_disable_unprepare()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The commit 3370155737 ("printk: Userspace format indexing support")
caused the following build failure:
arch/mips/kernel/genex.o: In function `handle_mcheck_int':
(.text+0x190c): undefined reference to `printk'
arch/mips/kernel/genex.o: In function `handle_reserved_int':
(.text+0x1c8c): undefined reference to `printk'
Fixes: 3370155737 ("printk: Userspace format indexing support")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Chris Down <chris@chrisdown.name>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/YPbBfdz9srIpI+bb@chrisdown.name
Misplaced braces makes it difficult to follow the code easily. This also
goes against the code style guidelines. This resolved following checkpatch
complaints:
ERROR: open brace '{' following function definitions go on the next line
ERROR: that open brace { should be on the previous line
Link: https://lore.kernel.org/linux-media/YIwk3KbVGRPJwKa4@dU2104
[mchehab: dropped a hunk with a merge conflict]
Cc: linux-media@vger.kernel.org, devel@driverdev.osuosl.org, linux-kernel@vger.kernel.org, drv@mailo.com # X-LSpam-Score: -7.3 (-------)
Signed-off-by: Deepak R Varma <drv@mailo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is no need to memset() both dvs_grid_info and dvs_stat_grid_info
separately: they are part of the same union. Instead, just zero the
union itself. This additionally avoids a false positive (due to a
gcc optimization bug[1]) when building with the coming FORTIFY_SOURCE
improvements:
In function 'fortify_memset_chk',
inlined from 'sh_css_pipe_get_grid_info' at drivers/staging/media/atomisp/pci/sh_css.c:5186:3,
inlined from 'ia_css_stream_create' at drivers/staging/media/atomisp/pci/sh_css.c:9442:10:
./include/linux/fortify-string.h:199:4: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
199 | __write_overflow_field();
| ^~~~~~~~~~~~~~~~~~~~~~~~
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=101419
Link: https://lore.kernel.org/linux-media/20210711145101.1434065-1-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Removed an unnecessary (void *) cast for an argument passed to kfree().
Link: https://lore.kernel.org/linux-media/20210605020855.1065-3-fmdefrancesco@gmail.com
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>