According to sysfs-bus-iio documentation the unit for accelerometer
values after applying scale/offset should be m/s^2, not g, which explains
why the scale values for the other variants in bmc150-accel do not match
exactly the values given in the datasheet.
To get the correct values, we need to multiply the BMA222 scale values
by g = 9.80665 m/s^2.
Fixes: a1a210bf29 ("iio: accel: bmc150-accel: Add support for BMA222")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-2-stephan@gerhold.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gcc reports build error when CONFIG_IIO_TRIGGERED_BUFFER is not set:
riscv64-linux-gnu-ld: drivers/iio/dummy/iio_simple_dummy_buffer.o: in function `iio_simple_dummy_configure_buffer':
iio_simple_dummy_buffer.c:(.text+0x2b0): undefined reference to `iio_triggered_buffer_setup_ext'
riscv64-linux-gnu-ld: drivers/iio/dummy/iio_simple_dummy_buffer.o: in function `.L0 ':
iio_simple_dummy_buffer.c:(.text+0x2fc): undefined reference to `iio_triggered_buffer_cleanup'
Fix it by select IIO_TRIGGERED_BUFFER for config IIO_SIMPLE_DUMMY_BUFFER.
Fixes: 738f6ba118 ("iio: dummy: iio_simple_dummy_buffer: use triggered buffer core calls")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Disable reg and clk when devm_gpiod_get_optional() fails in adf4350_probe().
Fixes:4a89d2f47ccd ("iio: adf4350: Convert to use GPIO descriptor")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210601142605.3613605-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the BMA253 datasheet [1] and BMA250 datasheet [2] the
bandwidth value for BMA25x should be set as 01xxx:
"Settings 00xxx result in a bandwidth of 7.81 Hz; [...]
It is recommended [...] to use the range from ´01000b´ to ´01111b´
only in order to be compatible with future products."
However, at the moment the drivers sets bandwidth values from 0 to 6,
which is not recommended and always results into 7.81 Hz bandwidth
according to the datasheet.
Fix this by introducing a bw_offset = 8 = 01000b for BMA25x,
so the additional bit is always set for BMA25x.
[1]: https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bma253-ds000.pdf
[2]: https://datasheet.octopart.com/BMA250-Bosch-datasheet-15540103.pdf
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Fixes: 2017cff24c ("iio:bma180: Add BMA250 chip support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210526094408.34298-2-stephan@gerhold.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use to_pci_dev() helper instead of container_of(d, struct pci_dev, dev);
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20210611115558.796338-2-jarkko.nikula@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove CONFIG_PM ifdef and mark PM callbacks with __maybe_unused.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20210611115558.796338-1-jarkko.nikula@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO ADC group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513111035.77950-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO IMU group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513122512.93187-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since all AD Sigma-Delta drivers now use the
devm_ad_sd_setup_buffer_and_trigger() function, we can remove the old
ad_sd_{setup,cleanup}_buffer_and_trigger() functions.
This way we can discourage new drivers that use the ad_sigma_delta
lib-driver to use these (older functions).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-13-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As not many steps were not already devm_ managed, use
devm_add_action_or_reset() to handle the rest.
This also uses the new devm_ad_sd_setup_buffer_and_trigger() function.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-12-aardelean@deviqon.com
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7192 driver to use device-managed
functions.
The regulators and the mclk requires devm_add_action_or_reset() callbacks
though.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-11-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_optional() helper returns NULL when devm_clk_get() returns
-ENOENT.
This makes things slightly cleaner. The added benefit is mostly cosmetic.
Also, a minor detail with this call, is that the reference for the parent
device is taken as `spi->dev` instead of `&st->sd.spi->dev` (which looks a
little quirky).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-10-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7780 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-9-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7791 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-8-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7793 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-7-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a version of ad_sd_setup_buffer_and_trigger() with all underlying
functions (that are used) being replaced with their device-managed
variants.
One thing to take care here is with {devm_}iio_trigger_alloc(), where both
functions take a parent-device object as the first parameter.
To make sure nothing quirky is happening, the devm_ad_sd_probe_trigger()
function is checking that the provided 'dev' reference is the same as the
one stored on the 'struct ad_sigma_delta' driver data.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SOC_SIFIVE Kconfig entry unconditionally selects ERRATA_SIFIVE.
However, ERRATA_SIFIVE depends on RISCV_ERRATA_ALTERNATIVE, which is
not set, so SOC_SIFIVE should either depend on or select
RISCV_ERRATA_ALTERNATIVE. Use 'select' here to quieten the Kconfig
warning.
WARNING: unmet direct dependencies detected for ERRATA_SIFIVE
Depends on [n]: RISCV_ERRATA_ALTERNATIVE [=n]
Selected by [y]:
- SOC_SIFIVE [=y]
Fixes: 1a0e5dbd37 ("riscv: sifive: Add SiFive alternative ports")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Cc: Vincent Chen <vincent.chen@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
When CONFIG_CMODEL_MEDLOW is used it ends up generating riscv_hi20_rela
relocations in modules which are not resolved during runtime and
following errors would be seen
[ 4.802714] virtio_input: target 00000000c1539090 can not be addressed by the 32-bit offset from PC = 39148b7b
[ 4.854800] virtio_input: target 00000000c1539090 can not be addressed by the 32-bit offset from PC = 9774456d
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
* A pair of XIP fixes: one to fix alternatives, and one to turn off the
rest of the features that require code modification.
* A fix to a type that was causing some alternatives to break.
* A build fix for BUILTIN_DTB.
-----BEGIN PGP SIGNATURE-----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=c3op
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A pair of XIP fixes: one to fix alternatives, and one to turn off the
rest of the features that require code modification
- A fix to a type that was causing some alternatives to break
- A build fix for BUILTIN_DTB
* tag 'riscv-for-linus-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix BUILTIN_DTB for sifive and microchip soc
riscv: alternative: fix typo in macro name
riscv: code patching only works on !XIP_KERNEL
riscv: xip: support runtime trap patching
0day robot reported a 9.2% regression for will-it-scale mmap1 test
case[1], caused by commit 57efa1fe59 ("mm/gup: prevent gup_fast from
racing with COW during fork").
Further debug shows the regression is due to that commit changes the
offset of hot fields 'mmap_lock' inside structure 'mm_struct', thus some
cache alignment changes.
From the perf data, the contention for 'mmap_lock' is very severe and
takes around 95% cpu cycles, and it is a rw_semaphore
struct rw_semaphore {
atomic_long_t count; /* 8 bytes */
atomic_long_t owner; /* 8 bytes */
struct optimistic_spin_queue osq; /* spinner MCS lock */
...
Before commit 57efa1fe59 adds the 'write_protect_seq', it happens to
have a very optimal cache alignment layout, as Linus explained:
"and before the addition of the 'write_protect_seq' field, the
mmap_sem was at offset 120 in 'struct mm_struct'.
Which meant that count and owner were in two different cachelines,
and then when you have contention and spend time in
rwsem_down_write_slowpath(), this is probably *exactly* the kind
of layout you want.
Because first the rwsem_write_trylock() will do a cmpxchg on the
first cacheline (for the optimistic fast-path), and then in the
case of contention, rwsem_down_write_slowpath() will just access
the second cacheline.
Which is probably just optimal for a load that spends a lot of
time contended - new waiters touch that first cacheline, and then
they queue themselves up on the second cacheline."
After the commit, the rw_semaphore is at offset 128, which means the
'count' and 'owner' fields are now in the same cacheline, and causes
more cache bouncing.
Currently there are 3 "#ifdef CONFIG_XXX" before 'mmap_lock' which will
affect its offset:
CONFIG_MMU
CONFIG_MEMBARRIER
CONFIG_HAVE_ARCH_COMPAT_MMAP_BASES
The layout above is on 64 bits system with 0day's default kernel config
(similar to RHEL-8.3's config), in which all these 3 options are 'y'.
And the layout can vary with different kernel configs.
Relayouting a structure is usually a double-edged sword, as sometimes it
can helps one case, but hurt other cases. For this case, one solution
is, as the newly added 'write_protect_seq' is a 4 bytes long seqcount_t
(when CONFIG_DEBUG_LOCK_ALLOC=n), placing it into an existing 4 bytes
hole in 'mm_struct' will not change other fields' alignment, while
restoring the regression.
Link: https://lore.kernel.org/lkml/20210525031636.GB7744@xsang-OptiPlex-9020/ [1]
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Elder says:
====================
net: qualcomm: rmnet: MAPv4 download checksum cleanup, part 2
This is part 2 of a large series that reworks some code that handles
downloaded packets when MAPv4 checksum offload is enabled. The
first part, which includes an overview, is here:
https://lore.kernel.org/netdev/20210611190529.3085813-1-elder@linaro.org/
This second part of the series completes the simplification of this
handling code, removing unnecessary byte swaps and bitwise inversions
of checksum values, and along the way avoids the need for almost all
of the forced type casts. The checksum field in an RMNet download
trailer is given __sum16_t type to accurately reflect the meaning of
that field.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support any extension headers for IPv6 packets. Extension
headers therefore contribute 0 bytes to the payload length. As a
result we can just use the IPv6 payload length as the length used to
compute the pseudo header checksum for both UDP and TCP messages.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We compare a payload checksum with a pseudo checksum value for
equality in rmnet_map_ipv4_dl_csum_trailer(). Both of those values
are computed with a unary NOT (~) operation. The result of the
comparison is the same if we omit that NOT for both values.
Remove these operations in rmnet_map_ipv6_dl_csum_trailer() also.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The csum_value field in the rmnet_map_dl_csum_trailer structure is a
"real" Internet checksum. It is a 16 bit value, in big endian format,
which represents an inverted ones' complement sum over pairs of bytes.
Make that clear by changing its type to __sum16.
This makes a typecast in rmnet_map_ipv4_dl_csum_trailer() and
another in rmnet_map_ipv6_dl_csum_trailer() unnecessary.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch makes rmnet_map_ipv4_dl_csum_trailer() return
early with an error if it is determined that the computed checksum
for the IP payload does not match what was expected.
If the computed checksum *does* match the expected value, the IP
payload (i.e., the transport message), can be considered good.
There is no need to do any further processing of the message.
This means a big block of code is unnecessary for validating the
transport checksum value, and can be removed.
Make comparable changes in rmnet_map_ipv6_dl_csum_trailer().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rmnet_map_ipv4_dl_csum_trailer(), if the sum of the trailer
checksum and the pseudo checksum is non-zero, checksum validation
has failed. We can return an error as soon as we know that.
We can do the same thing in rmnet_map_ipv6_dl_csum_trailer().
Add some comments that explain where we're headed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply demonstrates that a checksum value computed when
verifying an offloaded transport checksum value for both IPv4 and
IPv6 is (normally) 0. It can be squashed into the next patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the ones' complement arithmetic, the sum of two negated values
is equal to the negation of the sum of the two original values [1].
Rearrange the calculation ip6_payload_sum using this property.
[1] https://tools.ietf.org/html/rfc1071
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rmnet_map_ipv4_dl_csum_trailer(), remove the "csum_temp" and
"addend" local variables, and simplify a few lines of code.
Remove the "csum_temp", "csum_value", "ip6_hdr_csum", and "addend"
local variables in rmnet_map_ipv6_dl_csum_trailer(), and simplify a
few lines of code there as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loic Poulain says:
====================
net: Add WWAN link creation support
Most of the modern WWAN modems are able to support multiple network
contexts, allowing user to connect to different APNs (e.g. Internet,
MMS, etc...). These contexts are usually dynamically configured via
a control channel such as MBIM, QMI or AT.
Each context is naturally represented as a network link/device, and
the muxing of these links is usually vendor/bus specific (QMAP, MBIM,
intel iosm...). Today some drivers create a static collection of
netdevs at init time, some relies on VLAN link for associating a context
(cdc-mbim), some exposes sysfs attribute for dynamically creating
additional netdev (qmi_wwan add_mux attr) or relies on vendor specific
link type (rmnet) for performing the muxing... so there is no generic
way to handle WWAN links, making user side integration painful.
This series introduces a generic WWAN link management interface to the
WWAN framework, allowing user to dynamically create and remove WWAN
links through rtnetlink ('wwan' type). The underlying 'muxing' vendor
implementation is completely abstracted.
The idea is to use this interface for upcoming WWAN drivers (intel
iosm) and to progressively integrate support into existing ones
(qmi_wwan, cdc-mbim, mhi_net, etc...).
v2: - Squashed Johannes and Sergey changes
- Added IFLA_PARENT_DEV_BUS_NAME attribute
- reworded commit message + introduce Sergey's comment
v3: - Added basic new interface user to this series (mhi_net)
- Moved IFLA_PARENT_DEV_NAME nla_policy introduction to right patch
- Added cover letter
- moved kdoc to .c file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Register wwan_ops for link management via wwan rtnetlink. This is
only basic support for now, since we only support creating one
single link (link-0), but is useful to validate new wwan rtnetlink
interface.
For backward compatibity support, we still register a default netdev
at probe time, except if 'create_default_iface' module parameter is
set to false.
This has been tested with iproute2 and mbimcli:
$ ip link add dev wwan0-0 parentdev-name wwan0 type wwan linkid 0
$ mbimcli -p -d /dev/wwan0p2MBIM --connect apn=free
$ ip link set dev wwan0-0 up
$ ip addr add dev wwan0 ${IP}
$ ip route replace default via ${IP}
$ ping 8.8.8.8
...
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to create (and destroy) interfaces via a new
rtnetlink kind "wwan". The responsible driver has to use
the new wwan_register_ops() to make this possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, for example in the upcoming WWAN framework changes,
there's no natural "parent netdev", so sometimes dummy netdevs are
created or similar. IFLA_PARENT_DEV_NAME is a new attribute intended to
contain a device (sysfs, struct device) name that can be used instead
when creating a new netdev, if the rtnetlink family implements it.
As suggested by Parav Pandit, we also introduce IFLA_PARENT_DEV_BUS_NAME
attribute in order to uniquely identify a device on the system (with
bus/name pair).
ip-link(8) support for the generic parent device attributes will help
us avoid code duplication, so no other link type will require a custom
code to handle the parent name attribute. E.g. the WWAN interface
creation command will looks like this:
$ ip link add wwan0-1 parent-dev wwan0 type wwan channel-id 1
So, some future subsystem (or driver) FOO will have an interface
creation command that looks like this:
$ ip link add foo1-3 parent-dev foo1 type foo bar-id 3 baz-type Y
Below is an example of dumping link info of a random device with these
new attributes:
$ ip --details link show wlp0s20f3
4: wlp0s20f3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UP mode DORMANT group default qlen 1000
...
parent_bus pci parent_dev 0000:00:14.3
Co-developed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Co-developed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Suggested-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make rtnetlink ops that can create different
kinds of devices, like what we want to add to the WWAN
framework, the priv_size and setup parameters aren't quite
sufficient. Make this easier to manage by allowing ops to
allocate their own netdev via an @alloc method that gets
the tb netlink data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following kernel build warnings:
drivers/net/ethernet/ibm/ibmvnic.c:1516: warning: Function parameter or member 'skb' not described in 'build_hdr_descs_arr'
drivers/net/ethernet/ibm/ibmvnic.c:1516: warning: Function parameter or member 'indir_arr' not described in 'build_hdr_descs_arr'
drivers/net/ethernet/ibm/ibmvnic.c:1516: warning: Excess function parameter 'txbuff' description in 'build_hdr_descs_arr'
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/ibm/ibmvnic.c: In function ‘adapter_state_to_string’:
drivers/net/ethernet/ibm/ibmvnic.c:855:2: warning: enumeration value ‘VNIC_DOWN’ not handled in switch [-Wswitch]
855 | switch (state) {
| ^~~~~~
drivers/net/ethernet/ibm/ibmvnic.c: In function ‘reset_reason_to_string’:
drivers/net/ethernet/ibm/ibmvnic.c:1958:2: warning: enumeration value ‘VNIC_RESET_PASSIVE_INIT’ not handled in switch [-Wswitch]
1958 | switch (reason) {
| ^~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a panic in socket ioctl cmd SIOCGSKNS when NET_NS is not enabled.
The reason is that nsfs tries to access ns->ops but the proc_ns_operations
is not implemented in this case.
[7.670023] Unable to handle kernel NULL pointer dereference at virtual address 00000010
[7.670268] pgd = 32b54000
[7.670544] [00000010] *pgd=00000000
[7.671861] Internal error: Oops: 5 [#1] SMP ARM
[7.672315] Modules linked in:
[7.672918] CPU: 0 PID: 1 Comm: systemd Not tainted 5.13.0-rc3-00375-g6799d4f2da49 #16
[7.673309] Hardware name: Generic DT based system
[7.673642] PC is at nsfs_evict+0x24/0x30
[7.674486] LR is at clear_inode+0x20/0x9c
The same to tun SIOCGSKNS command.
To fix this problem, we make get_net_ns() return -EINVAL when NET_NS is
disabled. Meanwhile move it to right place net/core/net_namespace.c.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Fixes: c62cce2cae ("net: add an ioctl to get a socket network namespace")
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wong Vee Khee says:
====================
stmmac: intel: minor clean-up
This patch series include two minor-cleanup patches:
1. Move all the hardcoded DEFINEs to dwmac-intel header file.
2. Fix the wrong kernel-doc on the intel_eth_pci_remove() function.
Since the changes are minor, only basic sanity tests are done on a
Intel TigerLake with Marvell88E2110 PHY:-
- Link is up and able to perform ping.
- phc2sys and ptp4l are running without errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel-doc for intel_eth_pci_remove is incorrect, pdev datatype is
struct pci_dev. Changed it to the 'pci device pointer'.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently some of the dwmac-intel definitions are in the header file,
while some are in the driver source file. Cleaning this by moving all
the definitions to the header file.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steen Hegelund says:
====================
Add 25G BASE-R support
This series add the 25G BASE-R mode to the set modes supported.
This mode is used by the Sparx5 Switch for its 25G SerDes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 25gbase-r interface type and speed to phylink.
This is needed for the Sparx5 switch.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 25gbase-r modules. This is needed for the Sparx5 switch.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 25gbase-r phy interface mode
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 25gbase-r PHY interface mode.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/iucv: updates 2021-06-11
please apply the following iucv patches to netdev's net-next tree.
This cleans up a pattern of forward declarations in two iucv drivers,
so that they stop causing compile warnings with gcc11.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The forward declarations for the iucv_handler callbacks are causing
various compile warnings with gcc-11. Reshuffle the code to get rid
of these prototypes.
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are a number of tiny USB fixes for 5.13-rc6.
There are more than I would normally like, but there's been a bunch of
people banging on the gadget and dwc3 and typec code recently for I
think an Android release, which has resulted in a number of small fixes.
It's nice to see companies send fixes upstream for this type of work, a
notable change from years ago.
Anyway, fixes in here are:
- usb-serial device id updates
- usb-serial cp210x driver fixes for broken firmware versions
- typec fixes for crazy charging devices and other reported
problems
- dwc3 fixes for reported problems found
- gadget fixes for reported problems
- tiny xhci fixes
- other small fixes for reported issues.
- revert of a problem fix found by linux-next testing
All of these have passed 0-day and linux-next testing with no reported
problems (the revert for the found linux-next build problem included).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYMS6uA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknTgCeKSmtJABTIcZ3LLRgArqUFEroUqEAni2ZRv/8
3mGzeXFKvvoEO/WoILmV
=WqGE
-----END PGP SIGNATURE-----
Merge tag 'usb-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of tiny USB fixes for 5.13-rc6.
There are more than I would normally like, but there's been a bunch of
people banging on the gadget and dwc3 and typec code recently for I
think an Android release, which has resulted in a number of small
fixes. It's nice to see companies send fixes upstream for this type of
work, a notable change from years ago.
Anyway, fixes in here are:
- usb-serial device id updates
- usb-serial cp210x driver fixes for broken firmware versions
- typec fixes for crazy charging devices and other reported problems
- dwc3 fixes for reported problems found
- gadget fixes for reported problems
- tiny xhci fixes
- other small fixes for reported issues.
- revert of a problem fix found by linux-next testing
All of these have passed 0-day and linux-next testing with no reported
problems (the revert for the found linux-next build problem included)"
* tag 'usb-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (44 commits)
Revert "usb: gadget: fsl: Re-enable driver for ARM SoCs"
usb: typec: mux: Fix copy-paste mistake in typec_mux_match
usb: typec: ucsi: Clear PPM capability data in ucsi_init() error path
usb: gadget: fsl: Re-enable driver for ARM SoCs
usb: typec: wcove: Use LE to CPU conversion when accessing msg->header
USB: serial: cp210x: fix CP2102N-A01 modem control
USB: serial: cp210x: fix alternate function for CP2102N QFN20
usb: misc: brcmstb-usb-pinmap: check return value after calling platform_get_resource()
usb: dwc3: ep0: fix NULL pointer exception
usb: gadget: eem: fix wrong eem header operation
usb: typec: intel_pmc_mux: Put ACPI device using acpi_dev_put()
usb: typec: intel_pmc_mux: Add missed error check for devm_ioremap_resource()
usb: typec: intel_pmc_mux: Put fwnode in error case during ->probe()
usb: typec: tcpm: Do not finish VDM AMS for retrying Responses
usb: fix various gadget panics on 10gbps cabling
usb: fix various gadgets null ptr deref on 10gbps cabling.
usb: pci-quirks: disable D3cold on xhci suspend for s2idle on AMD Renoir
usb: f_ncm: only first packet of aggregate needs to start timer
USB: f_ncm: ncm_bitrate (speed) is unsigned
MAINTAINERS: usb: add entry for isp1760
...
Here is a single 8250_exar serial driver fix for a reported problem with
a change that happened in 5.13-rc1.
It has been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYMS7Tg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktQwCgkmCvU3KoftPUO6oRFrj7S3sJn0YAoNYLprQU
vaEojGhGWKIol/Cbsak9
=6apf
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"A single 8250_exar serial driver fix for a reported problem with a
change that happened in 5.13-rc1.
It has been in linux-next with no reported problems"
* tag 'tty-5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_exar: Avoid NULL pointer dereference at ->exit()