Implement support for pull-up (most pins) and pull-down (EDBGREQ)
handling for the R-Car V2H SoC, using the common R-Car bias handling.
Note that the R-Car V2H Hardware User's Manual Rev. 1.00 says that
the LSI Pin Pull-Up Control Register 11 (PUPR11) controls pull-ups for
the {SCK,WS,SDATA}[01] pins. These are assumed to be typos, as R-Car
V2H has only Serial Sound Interface channels 3 and 4.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/48d2abdd63ee43ed99cb32ed4a5f4d76ba563162.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for R-Car H2 and RZ/G1H SoCs, using the common R-Car bias
handling.
Note that on RZ/G1H, the "ASEBRK#/ACK" pin is called "ACK", but the code
doesn't handle that naming difference. Hence users should use the R-Car
naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/dde6e0b36a4e4494039a3466df208b5ec5c594ee.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for the RZ/G1C SoC, using the common R-Car bias handling.
Note that on RZ/G1C, the "ASEBRK#/ACK" pin is called "ACK", but the code
doesn't handle that naming difference. Hence users should use the R-Car
naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/18c8ebf9fa9e239253a723857e9dffeec775db7e.1619785375.git.geert+renesas@glider.be
Hygon systems support the MONITOR/MWAIT instructions and these can be
used for ACPI C1 in the same way as on AMD and Intel systems.
The BIOS declares a C1 state in _CST to use FFH and CPUID_Fn00000005_EDX
is non-zero on Hygon systems.
Allow ffh_cstate_init() to succeed on Hygon systems to default using FFH
MWAIT instead of HALT for ACPI C1.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210528081417.31474-1-puwen@hygon.cn
The GPIO pins connected to the 4 Software Switches ("SOFT_SW", SW12) do
not have external pull-up resistors, but rely on internal pull-ups being
enabled. Fortunately this is satisfied by the initial state of these
pins.
Make this explicit by enabling bias-pull-up, to remove the dependency on
initial state and/or boot loader configuration.
While at it, rename the surrounding device node from "gpio-keys" to
"keyboard", to comply with generic node name recommendations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/45f38a5333feba9bea80efeb5a41a6c3f60deda2.1619785905.git.geert+renesas@glider.be
The GPIO pins connected to the 4 Software Switches ("SOFT_SW", SW2) do
not have external pull-up resistors, but rely on internal pull-ups being
enabled. Fortunately this is satisfied by the initial state of these
pins.
Make this explicit by enabling bias-pull-up, to remove the dependency on
initial state and/or boot loader configuration.
While at it, rename the surrounding device node from "gpio-keys" to
"keyboard", to comply with generic node name recommendations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1cdec892b1491309b12bdaf7bc8428b3a19b1ed5.1619785905.git.geert+renesas@glider.be
The GPIO pins connected to the 4 Software Switches (SW2) and the second
Tact Switch (SW25) do not have external pull-up resistors, but rely on
internal pull-ups being enabled. Fortunately this is satisfied by the
initial state of these pins.
Make this explicit by enabling bias-pull-up, to remove the dependency on
initial state and/or boot loader configuration.
Note that the GPIO pin connected to the first Tact Switch (SW24) does
have an external pull-up resistor.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/011e4c461767f2dd690b655b3dd501eb554184c1.1619785905.git.geert+renesas@glider.be
The GPIO pins connected to the 4 Software Switches (SW2) do not have
external pull-up resistors, but rely on internal pull-ups being enabled.
Fortunately this is satisfied by the initial state of these pins.
Make this explicit by enabling bias-pull-up, to remove the dependency on
initial state and/or boot loader configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/9fae3c0c2c0000f6b43c9ce87fe64a594b30a7da.1619785905.git.geert+renesas@glider.be
Correct the voltages in the "Power Optimized" (<= 1.5 GHz) Cortex-A57
operating point table entries for the R-Car M3-W and M3-W+ SoCs from
0.82V to 0.83V, as per the R-Car Gen3 EC Manual Errata for Revision
0.53.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b9e9db907514790574429b83d070c823b36085ef.1619699909.git.geert+renesas@glider.be
Tag the highest "Power Optimized" (1.5 GHz) Cortex-A57 operating point
table entries for the RZ/G2M, R-Car M3-W and M3-W+ SoCs with the
"opp-suspend" property. This makes sure the system will enter suspend
in the same performance state as it will be resumed by the firmware
later, avoiding state inconsistencies after resume.
Based on a patch for R-Car M3-W in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Fixes: 800037e815 ("arm64: dts: renesas: r8a774a1: Add operating points")
Fixes: da7e311334 ("arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices")
Fixes: f51746ad7d ("arm64: dts: renesas: Add Renesas R8A77961 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/45a061c3b0463aac7d10664f47c4afdd999da50d.1619699721.git.geert+renesas@glider.be
When the code execute this if statement, the value of ret is 0.
However, we can see from the dev_err() log that the value of
ret should be -EINVAL.
Clean up smatch warning:
drivers/phy/ti/phy-j721e-wiz.c:1216 wiz_probe() warn: missing error code 'ret'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: c9f9eba066 ("phy: ti: j721e-wiz: Manage typec-gpio-dir")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1621939832-65535-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20210520135132.37628-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Current dts files with Rockchip 'usbphy' nodes are manually verified.
In order to automate this process rockchip-usb-phy.txt has to be
converted to YAML.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210518165658.12764-2-jbx6244@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The RK3308 SoC uses a slightly different USB phy than other Rockchip
parts.
This commit adds support for that phy.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20210514150044.2099298-3-t.schramm@manjaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The RK3308 features a slightly different USB phy than other Rockchip SoCs.
This patch adds a compatible string for it.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210514150044.2099298-2-t.schramm@manjaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210517120821.26466-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds vbus-supply optional property to phy sub-nodes using
connector node.
A regulator for USB VBUS may be needed for host mode.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210517120821.26466-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A * has been added at the starting of new line
The closing */ of multi line comment shifted to new line
This is done to maintain code uniformity.
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Link: https://lore.kernel.org/r/20210428165515.o47o5awzdxirxkqi@kewl-virtual-machine
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use clk_disable_unprepare() in the error path of mtk_phy_init() to fix
some resource leaks.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1621420659-15858-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: a43f72ae13 ("phy: cadence: Sierra: Change MAX_LANES of Sierra to 16")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Link: https://lore.kernel.org/r/20210517015749.127799-1-wangwensheng4@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some arches (um, sparc64, riscv, xtensa) cause a Kconfig warning for
LOCKDEP.
These arch-es select LOCKDEP_SUPPORT but they are not listed as one
of the arch-es that LOCKDEP depends on.
Since (16) arch-es define the Kconfig symbol LOCKDEP_SUPPORT if they
intend to have LOCKDEP support, replace the awkward list of
arch-es that LOCKDEP depends on with the LOCKDEP_SUPPORT symbol.
But wait. LOCKDEP_SUPPORT is included in LOCK_DEBUGGING_SUPPORT,
which is already a dependency here, so LOCKDEP_SUPPORT is redundant
and not needed.
That leaves the FRAME_POINTER dependency, but it is part of an
expression like this:
depends on (A && B) && (FRAME_POINTER || B')
where B' is a dependency of B so if B is true then B' is true
and the value of FRAME_POINTER does not matter.
Thus we can also delete the FRAME_POINTER dependency.
Fixes this kconfig warning: (for um, sparc64, riscv, xtensa)
WARNING: unmet direct dependencies detected for LOCKDEP
Depends on [n]: DEBUG_KERNEL [=y] && LOCK_DEBUGGING_SUPPORT [=y] && (FRAME_POINTER [=n] || MIPS || PPC || S390 || MICROBLAZE || ARM || ARC || X86)
Selected by [y]:
- PROVE_LOCKING [=y] && DEBUG_KERNEL [=y] && LOCK_DEBUGGING_SUPPORT [=y]
- LOCK_STAT [=y] && DEBUG_KERNEL [=y] && LOCK_DEBUGGING_SUPPORT [=y]
- DEBUG_LOCK_ALLOC [=y] && DEBUG_KERNEL [=y] && LOCK_DEBUGGING_SUPPORT [=y]
Fixes: 7d37cb2c91 ("lib: fix kconfig dependency on ARCH_WANT_FRAME_POINTERS")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Waiman Long <longman@redhat.com>
Link: https://lkml.kernel.org/r/20210524224150.8009-1-rdunlap@infradead.org
The block condition matrix is using 'E' as the writer notation,
however, the writer reminder below the matrix is using 'W', to make
them consistent and make the matrix more readable, we'd better to use
'W' to represent writer.
Suggested-by: Waiman Long <llong@redhat.com>
Suggested-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Link: https://lkml.kernel.org/r/1621868745-23311-1-git-send-email-sxwjean@me.com
A kernel WARNING may be triggered when setting maxcpus=1.
The uncore counters are Die-scope. When probing a PCI device, only the
BUS information can be retrieved. The uncore driver has to maintain a
mapping table used to calculate the logical Die ID from a given BUS#.
Before the patch ba9506be4e, the mapping table stores the mapping
information from the BUS# -> a Physical Socket ID. To calculate the
logical die ID, perf does,
- In snbep_pci2phy_map_init(), retrieve the BUS# -> a Physical Socket ID
from the UBOX PCI configure space.
- Calculate the mapping information (a BUS# -> a Physical Socket ID) for
the other PCI BUS.
- In the uncore_pci_probe(), get the physical Socket ID from a given BUS
and the mapping table.
- Calculate the logical Die ID
Since only the logical Die ID is required, with the patch ba9506be4e,
the mapping table stores the mapping information from the BUS# -> a
logical Die ID. Now perf does,
- In snbep_pci2phy_map_init(), retrieve the BUS# -> a Physical Socket ID
from the UBOX PCI configure space.
- Calculate the logical Die ID
- Calculate the mapping information (a BUS# -> a logical Die ID) for the
other PCI BUS.
- In the uncore_pci_probe(), get the logical die ID from a given BUS and
the mapping table.
When calculating the logical Die ID, -1 may be returned, especially when
maxcpus=1. Here, -1 means the logical Die ID is not found. But when
calculating the mapping information for the other PCI BUS, -1 indicates
that it's the other PCI BUS that requires the calculation of the
mapping. The driver will mistakenly do the calculation.
Uses the -ENODEV to indicate the case which the logical Die ID is not
found. The driver will not mess up the mapping table anymore.
Fixes: ba9506be4e ("perf/x86/intel/uncore: Store the logical die id instead of the physical die id.")
Reported-by: John Donnelly <john.p.donnelly@oracle.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: John Donnelly <john.p.donnelly@oracle.com>
Tested-by: John Donnelly <john.p.donnelly@oracle.com>
Link: https://lkml.kernel.org/r/1622037527-156028-1-git-send-email-kan.liang@linux.intel.com
KCSAN reports a data race between increment and decrement of pin_count:
write to 0xffff888237c2d4e0 of 4 bytes by task 15740 on cpu 1:
find_get_context kernel/events/core.c:4617
__do_sys_perf_event_open kernel/events/core.c:12097 [inline]
__se_sys_perf_event_open kernel/events/core.c:11933
...
read to 0xffff888237c2d4e0 of 4 bytes by task 15743 on cpu 0:
perf_unpin_context kernel/events/core.c:1525 [inline]
__do_sys_perf_event_open kernel/events/core.c:12328 [inline]
__se_sys_perf_event_open kernel/events/core.c:11933
...
Because neither read-modify-write here is atomic, this can lead to one
of the operations being lost, resulting in an inconsistent pin_count.
Fix it by adding the missing locking in the CPU-event case.
Fixes: fe4b04fa31 ("perf: Cure task_oncpu_function_call() races")
Reported-by: syzbot+142c9018f5962db69c7e@syzkaller.appspotmail.com
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210527104711.2671610-1-elver@google.com
Checking for and processing RCU-nocb deferred wakeup upon user/guest
entry is only relevant when nohz_full runs on the local CPU, otherwise
the periodic tick should take care of it.
Make sure we don't needlessly pollute these fast-paths as a -3%
performance regression on a will-it-scale.per_process_ops has been
reported so far.
Fixes: 47b8ff194c (entry: Explicitly flush pending rcuog wakeup before last rescheduling point)
Fixes: 4ae7dc97f7 (entry/kvm: Explicitly flush pending rcuog wakeup before last rescheduling point)
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210527113441.465489-1-frederic@kernel.org
During the update of fair blocked load (__update_blocked_fair()), we
update the contribution of the cfs in tg->load_avg if cfs_rq's pelt
has decayed. Nevertheless, the pelt values of a cfs_rq could have
been recently updated while propagating the change of a child. In this
case, cfs_rq's pelt will not decayed because it has already been
updated and we don't update tg->load_avg.
__update_blocked_fair
...
for_each_leaf_cfs_rq_safe: child cfs_rq
update cfs_rq_load_avg() for child cfs_rq
...
update_load_avg(cfs_rq_of(se), se, 0)
...
update cfs_rq_load_avg() for parent cfs_rq
-propagation of child's load makes parent cfs_rq->load_sum
becoming null
-UPDATE_TG is not set so it doesn't update parent
cfs_rq->tg_load_avg_contrib
..
for_each_leaf_cfs_rq_safe: parent cfs_rq
update cfs_rq_load_avg() for parent cfs_rq
- nothing to do because parent cfs_rq has already been updated
recently so cfs_rq->tg_load_avg_contrib is not updated
...
parent cfs_rq is decayed
list_del_leaf_cfs_rq parent cfs_rq
- but it still contibutes to tg->load_avg
we must set UPDATE_TG flags when propagting pending load to the parent
Fixes: 039ae8bcf7 ("sched/fair: Fix O(nr_cgroups) in the load balancing path")
Reported-by: Odin Ugedal <odin@uged.al>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Odin Ugedal <odin@uged.al>
Link: https://lkml.kernel.org/r/20210527122916.27683-3-vincent.guittot@linaro.org
when removing a cfs_rq from the list we only check _sum value so we must
ensure that _avg and _sum stay synced so load_sum can't be null whereas
load_avg is not after propagating load in the cgroup hierarchy.
Use load_avg to compute load_sum similarly to what is done for util_sum
and runnable_sum.
Fixes: 0e2d2aaaae ("sched/fair: Rewrite PELT migration propagation")
Reported-by: Odin Ugedal <odin@uged.al>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Odin Ugedal <odin@uged.al>
Link: https://lkml.kernel.org/r/20210527122916.27683-2-vincent.guittot@linaro.org
This fix the recent removal of clock drivers selection.
While it is not necessary to select the clock drivers themselves, we need
to select a proper implementation of the clock API, which for the meson, is
CCF
Fixes: ba66a25536 ("arm64: meson: ship only the necessary clock controllers")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210429083823.59546-1-jbrunet@baylibre.com
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210409110243.41-1-linqiheng@huawei.com
The PCIe PHY version used in SDX55 is v4.20 which has different register
offsets compared to the v4.0x PHYs. So separate register defines are
used for init sequence and PHY status.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210427065400.18958-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the driver the interrupts are fetched by name. Therefore, add
interrupt names in the list of required properties
Fixes: 68989fe1c3 ("dt-bindings: usb: Convert cdns-usb3.txt to YAML schema")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210528060657.29100-1-a-govindraju@ti.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
We have only 2 inline sg entries and we allow 4 sg entries for the send
wr sge. Larger sgls entries will be chained. However when we build
in-capsule send wr sge, we iterate without taking into account that the
sgl may be chained and still fit in-capsule (which can happen if the sgl
is bigger than 2, but lower-equal to 4).
Fix in-capsule data mapping to correctly iterate chained sgls.
Fixes: 38e1800275 ("nvme-rdma: Avoid preallocating big SGL for data")
Reported-by: Walker, Benjamin <benjamin.walker@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In preparation of the support for v4.20 PCIe PHY in SDX55, use a
separate "phy_status" field for the status bit offset. This is needed
because, the v4.20 PHY uses a different offset for the PHY Status.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210427065400.18958-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of forcing interrupt trigger to be "falling edge" let's rely on the
platform to set it up according to how it is set up on a given board based
on data in device tree or ACPI tables.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/YK7iO96g+7yIC0l1@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that we get rid of the usage of id argument at probe again, let's
switch to the new i2c probe method; this will avoid for people
misusing the possibly unassigned id pointer again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210528071024.26450-2-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The recent change in elants_i2c driver to support more chips
introduced a regression leading to Oops at probing. The driver reads
id->driver_data, but the id may be NULL depending on the device type
the driver gets bound.
Replace the driver data extraction with the device_get_match_data()
helper, and define the driver data in OF table, too.
Fixes: 9517b95bdc ("Input: elants_i2c - add support for eKTF3624")
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1186454
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210528071024.26450-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before ksmbd_vfs_stream_read() return, memory allocate in
ksmbd_vfs_getcasexattr() need be freed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Before assigning wbuf to stream_buf, memory allocate in
ksmbd_vfs_getcasexattr() need be freed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
checkpatch.pl complains as the following:
Alignment should match open parenthesis.
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
checkpatch.pl complains as the following:
CHECK: Macro argument 'fp' may be better as '(fp)' to avoid
precedence issues.
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
There's no need to restore DMA context on CPU_CLUSTER_PM_ENTER_FAILED as
the DMA context won't be lost on errors.
Note that this does not cause invalid context restore as we already check
for busy DMA with omap_dma_busy() in CPU_CLUSTER_PM_ENTER, and block any
deeper idle states for the SoC by returning NOTIFY_BAD if busy.
If other drivers block deeper idle states with cpu_pm, we now just do a
pointless restore, but only if dma was not busy on CPU_CLUSTER_PM_ENTER.
Let's update the CPU_CLUSTER_PM_ENTER_FAILED handling for correctness,
and add a comment.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210518074347.16908-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>