Add QSPI controller support for Intel LGM SoC.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also added compatible
Support for Intel platform.
dt-bindings: spi: cadence-qspi: Add support for Intel lgm-qspi
(earlier patch mail thread and Ack-by)
link: "https://lore.kernel.org/lkml/5d6d1b85.1c69fb81.96938.0315@mx.google.com/"
Reference:
https://lkml.org/lkml/2020/6/1/50
---
v9:
- Vignesh review comments address and update
- Retain the patchv4 move the binding documentation from mtd to spi
directory.
- Add intel's compatible string over the legacy documentation
- Remove unused variable, CQSPI_SUPPORTS_MULTI_CHIPSELECT macro and check
- YAML convertion patch alone dropped
v8:
- As Mark suggested to add the dt-bindings documentation patches
end of the series , so dropped.
v7:
- Rob's review comments address and fixed dt-schema warning
- Pratyush review comments address and update
- DAC bit reset to 0 and 1 (enable/disable)
- tested QSI-NOR flash mx25l12805d on LGM soc, it's working after disable DAC
- Linus suggested to use 'num-cs' prperty instead of 'num-chipselect'
v6:
- Rob's review comments update
- add compatible string in properly aligned
- remove cadence-qspi extra comaptible string in example
v5:
- Rob's review comments update
- const with single compatible string kept
v4:
- Rob's review comments update
- remove '|' no formatting to preserve
- child node attributes follows under 'properties' under '@[0-9a-f]+$'.
v3:
- Pratyush review comments update
- CQSPI_SUPPORTS_MULTI_CHIPSELECT macro used instead of cqspi->use_direct_mode
- disable DAC support placed in end of controller_init
v2:
- Rob's review comments update for dt-bindings
- add 'oneOf' for compatible selection
- drop un-neccessary descriptions
- add the cdns,is-decoded-cs and cdns,rclk-en properties as schema
- remove 'allOf' in not required place
- add AdditionalProperties false
- add minItems/maxItems for qspi reset attributes
resend-v1:
- As per Mark's suggestion , reorder the patch series 1-3 driver
support patches, series 4-6 dt-bindings patches.
v1:
- initial version
Ramuthevar Vadivel Murugan (5):
spi: cadence-quadspi: Add QSPI support for Intel LGM SoC
spi: cadence-quadspi: Disable the DAC for Intel LGM SoC
spi: cadence-quadspi: Add multi-chipselect support for Intel LGM SoC
spi: Move cadence-quadspi.txt to Documentation/devicetree/bindings/spi
dt-bindings: spi: cadence-qspi: Add support for Intel lgm-qspi
.../bindings/{mtd => spi}/cadence-quadspi.txt | 1 +
drivers/spi/Kconfig | 2 +-
drivers/spi/spi-cadence-quadspi.c | 24 ++++++++++++++++++----
3 files changed, 22 insertions(+), 5 deletions(-)
rename Documentation/devicetree/bindings/{mtd => spi}/cadence-quadspi.txt (97%)
--
2.11.0
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Hi Mark
These are not so important, but for
soc-pcm cleanup patches.
Kuninori Morimoto (6):
ASoC: soc-pcm: move dpcm_set_fe_update_state()
ASoC: soc-pcm: add dpcm_set_be_update_state()
ASoC: soc-pcm: add soc_pcm_set_dai_params()
ASoC: soc-pcm: cleanup soc_pcm_apply_symmetry()
ASoC: soc-pcm: cleanup soc_pcm_params_symmetry()
ASoC: soc-pcm: setup pcm at one place in soc_new_pcm()
sound/soc/soc-pcm.c | 231 +++++++++++++++++---------------------------
1 file changed, 90 insertions(+), 141 deletions(-)
--
2.25.1
Thank you for your help !!
Best regards
---
Kuninori Morimoto
System takes a very long time to suspend after commit 215a22ed31
("ALSA: hda: Refactor codec PM to use direct-complete optimization"):
[ 90.065964] PM: suspend entry (s2idle)
[ 90.067337] Filesystems sync: 0.001 seconds
[ 90.185758] Freezing user space processes ... (elapsed 0.002 seconds) done.
[ 90.188713] OOM killer disabled.
[ 90.188714] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 90.190024] printk: Suspending console(s) (use no_console_suspend to debug)
[ 90.904912] intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [49C], continue to suspend
[ 321.262505] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[ 328.426919] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[ 329.490933] ACPI: EC: interrupt blocked
That commit keeps the codec suspended during the system suspend. However,
mute/micmute LED will clear codec's direct-complete flag by
dpm_clear_superiors_direct_complete().
This doesn't play well with SOF driver. When its runtime resume is
called for system suspend, hda_codec_jack_check() schedules
jackpoll_work which uses snd_hdac_is_power_on() to check whether codec
is suspended. Because the direct-complete path isn't taken,
pm_runtime_disable() isn't called so snd_hdac_is_power_on() returns
false and jackpoll continues to run, and snd_hda_power_up_pm() cannot
power up an already suspended codec in multiple attempts, causes the
long delay on system suspend:
if (dev->power.direct_complete) {
if (pm_runtime_status_suspended(dev)) {
pm_runtime_disable(dev);
if (pm_runtime_status_suspended(dev)) {
pm_dev_dbg(dev, state, "direct-complete ");
goto Complete;
}
pm_runtime_enable(dev);
}
dev->power.direct_complete = false;
}
When direct-complete path is taken, snd_hdac_is_power_on() returns true
and hda_jackpoll_work() is skipped by accident. So this is still not
correct.
If we were to use snd_hdac_is_power_on() in system PM path,
pm_runtime_status_suspended() should be used instead of
pm_runtime_suspended(), otherwise pm_runtime_{enable,disable}() may
change the outcome of snd_hdac_is_power_on().
Because devices suspend in reverse order (i.e. child first), it doesn't
make much sense to resume an already suspended codec from audio
controller. So avoid the issue by making sure jackpoll isn't used in
system PM process.
Fixes: 215a22ed31 ("ALSA: hda: Refactor codec PM to use direct-complete optimization")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-3-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify hda_codec_jack_wake_enable() to also support disable WAKEEN.
In addition, this patch also moves the WAKEEN disablement call out of
hda_codec_jack_check() into hda_codec_jack_wake_enable().
This is a preparation for next patch.
No functional change intended.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-2-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of queueing jackpoll_work, runtime resume the codec to let it
use different jack detection methods based on jackpoll_interval.
This partially matches SOF driver's behavior with commit a6e7d0a4bd
("ALSA: hda: fix jack detection with Realtek codecs when in D3"), the
difference is SOF unconditionally resumes the codec.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-1-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DP PHY vswing/pre-emphasis level programming the driver does is
related to the DPTX -> first LTTPR link segment only. Accordingly it
should be only programmed when link training the first LTTPR and kept
as-is when training subsequent LTTPRs and the DPRX. For these latter
PHYs the vs/pe levels will be set in response to writing the
DP_TRAINING_LANEx_SET_PHY_REPEATERy DPCD registers (by an upstream LTTPR
TX PHY snooping this write access of its downstream LTTPR/DPRX RX PHY).
The above is also described in DP Standard v2.0 under 3.6.6.1.
While at it simplify and add the LTTPR that is link trained to the debug
message in intel_dp_set_signal_levels().
Fixes: b30edfd8d0 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229172201.4155327-2-imre.deak@intel.com
Only the IPI-related functions in the smp_ops should be conditional
on the vector callback being available. The rest should still happen:
• xen_hvm_smp_prepare_boot_cpu()
This function does two things, both of which should still happen if
there is no vector callback support.
The call to xen_vcpu_setup() for vCPU0 should still happen as it just
sets up the vcpu_info for CPU0. That does happen for the secondary
vCPUs too, from xen_cpu_up_prepare_hvm().
The second thing it does is call xen_init_spinlocks(), which perhaps
counter-intuitively should *also* still be happening in the case
without vector callbacks, so that it can clear its local xen_pvspin
flag and disable the virt_spin_lock_key accordingly.
Checking xen_have_vector_callback in xen_init_spinlocks() itself
would affect PV guests, so set the global nopvspin flag in
xen_hvm_smp_init() instead, when vector callbacks aren't available.
• xen_hvm_smp_prepare_cpus()
This does some IPI-related setup by calling xen_smp_intr_init() and
xen_init_lock_cpu(), which can be made conditional. And it sets the
xen_vcpu_id to XEN_VCPU_ID_INVALID for all possible CPUS, which does
need to happen.
• xen_smp_cpus_done()
This offlines any vCPUs which doesn't fit in the global shared_info
page, if separate vcpu_info placement isn't available. That part also
needs to happen regardless of vector callback support.
• xen_hvm_cpu_die()
This doesn't actually do anything other than commin_cpu_die() right
right now in the !vector_callback case; all three teardown functions
it calls should be no-ops. But to guard against future regressions
it's useful to call it anyway, and for it to explicitly check for
xen_have_vector_callback before calling those additional functions.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-6-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
In the case where xen_have_vector_callback is false, we still register
the IPI vectors in xen_smp_intr_init() for the secondary CPUs even
though they aren't going to be used. Stop doing that.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-5-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
It's useful to be able to test non-vector event channel delivery, to make
sure Linux will work properly on older Xen which doesn't have it.
It's also useful for those working on Xen and Xen-compatible hypervisors,
because there are guest kernels still in active use which use PCI INTX
even when vector delivery is available.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-4-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
With INTX or GSI delivery, Xen uses the event channel structures of CPU0.
If the interrupt gets handled by Linux on a different CPU, then no events
are seen as pending. Rather than introducing locking to allow other CPUs
to process CPU0's events, just ensure that the PCI interrupts happens
only on CPU0.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-3-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().
We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.
To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.
Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
USBPHYC has a register per phy to control and monitor the debug interface
of the HS PHY through a digital debug access.
With this register, it is possible to know if PLL Lock input to phy is
high. That means the PLL is ready for HS operation.
Instead of using an hard-coded delay after PLL enable and PLL disable, use
this bit to ensure good operating of the HS PHY.
Also use an atomic counter (n_pll_cons) to count the actual number of PLL
consumers and get rid of stm32_usbphyc_has_one_phy_active.
The boolean active in the usbphyc_phy structure is kept, because we need to
know in remove if a phy_exit is required to properly disable the PLL.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-7-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To ensure a good balancing of regulators, and allow PLL disabling when the
driver is removed, call stm32_usbphyc_phy_exit on each ports to set phys
inactive and disable PLL.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-6-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To ensure a good balancing of regulators, force PLL disable either by
reset or by clearing the PLLEN bit.
If waiting the powerdown pulse delay isn't enough, return -EPROBE_DEFER
instead of polling the PLLEN bit, which will be low at the next probe.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Due to async_schedule_domain call in regulator_bulk_enable,
scheduling while atomic bug can raise if regulator_bulk_enable is called
under atomic context.
To avoid this issue, this patch replaces all regulator_bulk* by regulator_
per regulators.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PLL block requires to be powered with 1v1 and 1v8 supplies to catch
ENABLE signal.
Currently, supplies are managed through phy_ops .power_on/off, and PLL
activation/deactivation is managed through phy_ops .init/exit.
The sequence of phy_ops .power_on/.phy_init, .power_off/.exit is USB
drivers dependent.
To ensure a good behavior of the PLL, supplies have to be managed at PLL
activation/deactivation. That means the supplies need to be put in usbphyc
node and not in phy children nodes.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
PLL block requires to be powered with 1v1 and 1v8 supplies to catch ENABLE
signal.
Currently, supplies are managed through phy_ops .power_on/off, and PLL
activation/deactivation is managed through phy_ops .init/exit.
The sequence of phy_ops .power_on/.phy_init, .power_off/.exit is USB
drivers dependent.
To ensure a good behavior of the PLL, supplies have to be managed at PLL
activation/deactivation. That means the supplies need to be put in usbphyc
parent node and not in phy children nodes.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210105090525.23164-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With UBSAN enabled and building with clang, there are occasionally
warnings like
WARNING: modpost: vmlinux.o(.text+0xc533ec): Section mismatch in reference from the function arch_atomic64_or() to the variable .init.data:numa_nodes_parsed
The function arch_atomic64_or() references
the variable __initdata numa_nodes_parsed.
This is often because arch_atomic64_or lacks a __initdata
annotation or the annotation of numa_nodes_parsed is wrong.
for functions that end up not being inlined as intended but operating
on __initdata variables. Mark these as __always_inline, along with
the corresponding asm-generic wrappers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210108092024.4034860-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
S_FRAME_SIZE is the size of the pt_regs structure, no longer the size of
the kernel stack frame, the name is misleading. In keeping with arm32,
rename S_FRAME_SIZE to PT_REGS_SIZE.
Signed-off-by: Jianlin Lv <Jianlin.Lv@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210112015813.2340969-1-Jianlin.Lv@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This reverts commit 367c820ef0.
lockup_detector_init() makes heavy use of per-cpu variables and must be
called with preemption disabled. Usually, it's handled early during boot
in kernel_init_freeable(), before SMP has been initialised.
Since we do not know whether or not our PMU interrupt can be signalled
as an NMI until considerably later in the boot process, the Arm PMU
driver attempts to re-initialise the lockup detector off the back of a
device_initcall(). Unfortunately, this is called from preemptible
context and results in the following splat:
| BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
| caller is debug_smp_processor_id+0x20/0x2c
| CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.10.0+ #276
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x3c0
| show_stack+0x20/0x6c
| dump_stack+0x2f0/0x42c
| check_preemption_disabled+0x1cc/0x1dc
| debug_smp_processor_id+0x20/0x2c
| hardlockup_detector_event_create+0x34/0x18c
| hardlockup_detector_perf_init+0x2c/0x134
| watchdog_nmi_probe+0x18/0x24
| lockup_detector_init+0x44/0xa8
| armv8_pmu_driver_init+0x54/0x78
| do_one_initcall+0x184/0x43c
| kernel_init_freeable+0x368/0x380
| kernel_init+0x1c/0x1cc
| ret_from_fork+0x10/0x30
Rather than bodge this with raw_smp_processor_id() or randomly disabling
preemption, simply revert the culprit for now until we figure out how to
do this properly.
Reported-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20201221162249.3119-1-lecopzer.chen@mediatek.com
Link: https://lore.kernel.org/r/20210112221855.10666-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
One of the users can be built modular:
ERROR: modpost: "irq_check_status_bit" [drivers/perf/arm_spe_pmu.ko] undefined!
Fixes: fdd0296304 ("genirq: Move status flag checks to core")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201227192049.GA195845@roeck-us.net
BCM4908 seems to have slightly different registers but works when
programmed just like the STB one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210106205838.10964-3-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
BCM4908 uses the same PHY and may require just a slightly different
programming.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210106205838.10964-2-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Changes that require mentioning:
1. interrupt-names
Name "wakeup" was changed to the "wake". It matches example and what
Linux driver looks for in the first place
2. brcm,ipp and brcm,ioc
Both were described as booleans with 0 / 1 values. In examples they
were integers and Linux checks for int as well. Both got uint32.
3. Added minimal description
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210106205838.10964-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the following sparse warning:
drivers/phy/mediatek/phy-mtk-mipi-dsi.c:237:24: warning: symbol 'mtk_mipi_tx_driver' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1610415484-92497-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 156708adf2 ("SUNRPC: Move the svc_xdr_recvfrom()
tracepoint") tried to capture the correct XID in the trace record,
but this line in svc_recv:
rqstp->rq_xid = svc_getu32(&rqstp->rq_arg.head[0]);
alters the size of rq_arg.head[0].iov_len. The tracepoint records
the correct XID but an incorrect value for the length of the
xdr_buf's head.
To keep the trace callsites simple, I've created two trace classes.
One assumes the xdr_buf contains a full RPC message, and the XID
can be extracted from it. The other assumes the contents of the
xdr_buf are arbitrary, and the xid will be provided by the caller.
Currently there is only one user of each class, but I expect we will
need a few more tracepoints using each class as time goes on.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Commit 65dc2e7252 ("usb: dwc2: Update Core Reset programming flow.")
revealed that the phy isn't ready immediately after enabling it's
clocks. The dwc2_check_core_version() fails and the dwc2 usb driver
errors out.
Add a short delay to let the phy get up and running. There isn't any
documentation how much time is required, the value was chosen based on
tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <stable@vger.kernel.org> # v5.7+
Link: https://lore.kernel.org/r/20210107224901.2102479-1-dev@kresin.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a superblock is assigned the SECURITY_FS_USE_XATTR behavior by the
policy yet it lacks xattr support, try to fall back to genfs rather than
rejecting the mount. If a genfscon rule is found for the filesystem,
then change the behavior to SECURITY_FS_USE_GENFS, otherwise reject the
mount as before. A similar fallback is already done in security_fs_use()
if no behavior specification is found for the given filesystem.
This is needed e.g. for virtiofs, which may or may not support xattrs
depending on the backing host filesystem.
Example:
# seinfo --genfs | grep ' ramfs'
genfscon ramfs / system_u:object_r:ramfs_t:s0
# echo '(fsuse xattr ramfs (system_u object_r fs_t ((s0) (s0))))' >ramfs_xattr.cil
# semodule -i ramfs_xattr.cil
# mount -t ramfs none /mnt
Before:
mount: /mnt: mount(2) system call failed: Operation not supported.
After:
(mount succeeds)
# ls -Zd /mnt
system_u:object_r:ramfs_t:s0 /mnt
See also:
https://lore.kernel.org/selinux/20210105142148.GA3200@redhat.com/T/https://github.com/fedora-selinux/selinux-policy/pull/478
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
The field is only relevant for legacy DRM drivers. Its only non-legacy
user in the DRM core is in drm_file.c. This code is now protected by
CONFIG_DRM_LEGACY. Radeon, the only driver that used the field, has been
changed to maintain it's own copy.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112081035.6882-7-tzimmermann@suse.de
CONFIG_DRM_VM gets selected by CONFIG_DRM_LEGACY, but nothing else. So
remove it and build drm_vm.o as part of CONFIG_DRM_LEGACY.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112081035.6882-5-tzimmermann@suse.de
The function is declared in drm_cache.h. I also removed the curly
braces from the for loop to adhere to kernel coding style.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112081035.6882-3-tzimmermann@suse.de
The AGP wrapper functions serve no purpose. They used to handle
builds that have CONFIG_AGP unset. But their callers are all in
drm_agpsupport.c, which only gets build with CONFIG_AGP.
v2:
* clarify CONFIG_AGP in commit description (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112081035.6882-2-tzimmermann@suse.de
All EL0 returns go via ret_to_user(), which masks IRQs and notifies
lockdep and tracing before calling into do_notify_resume(). Therefore,
there's no need for do_notify_resume() to call trace_hardirqs_off(), and
the comment is stale. The call is simply redundant.
In ret_to_user() we call exit_to_user_mode(), which notifies lockdep and
tracing the IRQs will be enabled in userspace, so there's no need for
el0_svc_common() to call trace_hardirqs_on() before returning. Further,
at the start of ret_to_user() we call trace_hardirqs_off(), so not only
is this redundant, but it is immediately undone.
In addition to being redundant, the trace_hardirqs_on() in
el0_svc_common() leaves lockdep inconsistent with the hardware state,
and is liable to cause issues for any C code or instrumentation
between this and the call to trace_hardirqs_off() which undoes it in
ret_to_user().
This patch removes the redundant tracing calls and associated stale
comments.
Fixes: 23529049c6 ("arm64: entry: fix non-NMI user<->kernel transitions")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210107145310.44616-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
tmp_tfm is allocated, but not freed on subsequent kmalloc failure, which
leads to a memory leak. Free tmp_tfm.
Fixes: d46eb36995 ("evm: crypto hash replaced by shash")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
[zohar@linux.ibm.com: formatted/reworded patch description]
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Simplify stm32h7_spi_prepare_fthlv() function implementation,
no functional change intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alain Volmat <alain.volmat@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Antonio Borneo <antonio.borneo@st.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Roman Guskov <rguskov@dh-electronics.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-spi@vger.kernel.org
Link: https://lore.kernel.org/r/20210104123114.261596-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to force this to be trigger high here, as the firmware
properly configures the irq flags already. Drop it to save a line.
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210112001301.687628-1-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we use concrete version to determine the max_cmd_dword.
New entries should be added for compatible hardwares of new version
or on new platform, otherwise the device will use 16 dwords instead
of 64 even if it supports, which will degrade the performance.
This will decrease the compatibility and the maintainability.
Drop the switch-case statement of the version checking. Only version
less than 0x351 supports maximum 16 command dwords.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1610526716-14882-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fill in the controller speed limits, so the SPI core can use them for
validating SPI transfers, and adjust or reject transfers when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210113101916.1147695-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Fill in the effective bit rate used for transfers, so the SPI core can
calculate instead of estimate delays.
Restore "reverse Christmas tree" order of local variables while adding
new variables.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210113101916.1147695-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the useless field .version from the private structure, which is
set but never read.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20201223124505.40792-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>