V3U creates spurious interrupts which we need to handle. This costs time
until BUS_PHASE_DATA can be activated which is problematic for Gen2 SoCs
and earlier. Because of this we introduce two interrupt handlers here
which will call a generic main irq function once the timing critical
stuff is done.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ensure this irq runs as fast as possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
'flags' and 'io' are needed first, so they should be at the beginning of
the private struct.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To avoid the HW race condition on R-Car Gen2 and earlier, we need to
write to ICMCR as soon as possible in the interrupt handler. We can
improve this by writing a static value instead of masking out bits.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Store DMA mapping data in geni_i2c_dev struct to enhance DMA mapping
data scope. For example during shutdown callback to unmap DMA mapping,
this stored DMA mapping data can be used to call geni_se_tx_dma_unprep
and geni_se_rx_dma_unprep functions.
Add two helper functions geni_i2c_rx_msg_cleanup and
geni_i2c_tx_msg_cleanup to unwrap the things after rx/tx FIFO/DMA
transfers, so that the same can be used in geni_i2c_stop_xfer()
function during shutdown callback.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove all empty lines at the end of functions in pinctrl subsystem,
and make the code neat.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Zhaoyu Liu <zackaryliu@yeah.net>
Link: https://lore.kernel.org/r/X98NP6NFK1Afzrgd@manjaro
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, kprobes decodes the opcode right after single-stepping in
resume_execution(). But the opcode was already decoded while preparing
arch_specific_insn in arch_copy_kprobe().
Decode the opcode in arch_copy_kprobe() instead of in resume_execution()
and set some flags which classify the opcode for the resuming process.
[ bp: Massage commit message. ]
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lkml.kernel.org/r/160830072561.349576.3014979564448023213.stgit@devnote2
With the introduction of the 'include/uapi/linux/spi/spi.h' header, the
type of the macros are enforced to 'unsigned long int' via the _BITUL()
macro.
This causes some -Wformat warnings in the spi-stm32 driver.
This patch adds a double-negation operator to the bit-masks. Essentially,
the important values for debugging are 0 or 1, while masking them directly
would show 0 or BIT(x) values.
This way, the type of the arguments are automatically re-cast.
Fixes: f7005142da ("spi: uapi: unify SPI modes into a single spi.h header")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210104143103.56510-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ROHM PMIC regulator drivers only need the regmap pointer from
the parent device. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210105130221.GA3438042@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver for regulators exposed by the DVFSRC (dynamic voltage and
frequency scaling resource collector) found in devices based on
mt8183 and newer platforms.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Link: https://lore.kernel.org/r/1608790134-27425-12-git-send-email-henryc.chen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This code will leak "map->debugfs_name" because the if statement is
reversed so it only frees NULL pointers instead of non-NULL. In
fact the if statement is not required and should just be removed
because kfree() accepts NULL pointers.
Fixes: cffa4b2122 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X/RQpfAwRdLg0GqQ@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
bclk_ratio is unused. Removes bclk_ratio and .set_bclk_ratio callback.
Removes snd_soc_dai_set_bclk_ratio() in a few machine drivers which are
obviously using rt1015.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224101854.3024823-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Assuming the calibration state gets lost after system suspend.
Re-calibrates again when resuming.
The rt1015_priv is alloced by kzalloc. No need to initialize cali_done
to 0 in component probe callback.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201225030845.4138497-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the binding documentation pinctrl related nodes
must use '-pins$' and ''^(.*-)?pinmux$'' as names. Change all
to properly match them. Also default state is for consumer
nodes and shall be removed from here.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210104150651.32083-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This comment describes a security problem which was fixed in commit
1c954540c0 ("staging: vchiq: avoid mixing kernel and user pointers").
The bug is fixed now so the FIXME can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X/RnUjY3XkZohk7w@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201230013706.28698-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
See Documentation/core-api/printk-formats.rst.
h should no longer be used in the format specifier for printk.
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20201215145306.1901598-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register for extcon notification and set charging current depending on
the detected cable type. Current values are taken from vendor kernel,
where most charger types end up setting 650mA [0].
Also enable and disable the CHARGER regulator based on extcon events.
[0] https://github.com/krzk/linux-vendor-backup/blob/samsung/galaxy-s2-epic-4g-touch-sph-d710-exynos4210-dump/drivers/misc/max8997-muic.c#L1675-L1678
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently the fs sysctl inotify/max_user_instances is used to limit the
number of inotify instances on the system. For systems running multiple
workloads, the per-user namespace sysctl max_inotify_instances can be
used to further partition inotify instances. However there is no easy
way to set a sensible system level max limit on inotify instances and
further partition it between the workloads. It is much easier to charge
the underlying resource (i.e. memory) behind the inotify instances to
the memcg of the workload and let their memory limits limit the number
of inotify instances they can create.
With inotify instances charged to memcg, the admin can simply set
max_user_instances to INT_MAX and let the memcg limits of the jobs limit
their inotify instances.
Link: https://lore.kernel.org/r/20201220044608.1258123-1-shakeelb@google.com
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
When checking corrupted quota file we can bail out and leak allocated
info structure. Properly free info structure on error return.
Reported-by: syzbot+77779c9b52ab78154b08@syzkaller.appspotmail.com
Fixes: 11c514a99b ("quota: Sanity-check quota file headers on load")
Signed-off-by: Jan Kara <jack@suse.cz>
We have set up a repository for users to try newer releases more easily, and
keep records of known bugs.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20201222014756.ov5vi6fywylbp5n6@function
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It programs Plane's calculated x, y, offset to Plane SF register.
It does the calculation of x and y offsets using
skl_calc_main_surface_offset().
v3: Update commit message
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-4-jose.souza@intel.com
The calculation the offsets of the main surface will be needed by PSR2
selective fetch code so here splitting and exporting it.
No functional changes were done here.
v3: Rebased
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-3-jose.souza@intel.com
Now using plane damage clips property to calcualte the damaged area.
Selective fetch only supports one region to be fetched so software
needs to calculate a bounding box around all damage clips.
Now that we are not complete fetching each plane, there is another
loop needed as all the plane areas that intersect with the pipe
damaged area needs to be fetched from memory so the complete blending
of all planes can happen.
v2:
- do not shifting new_plane_state->uapi.dst only src is in 16.16 format
v4:
- setting plane selective fetch area using the whole pipe damage area
- mark the whole plane area damaged if plane visibility or alpha
changed
v5:
- taking in consideration src.y1 in the damage coordinates
- adding to the pipe damaged area planes that were visible but are
invisible in the new state
v6:
- consider old state plane coordinates when visibility changes or it
moved to calculate damaged area
- remove from damaged area the portion not in src clip
v7:
- intersec every damage clip with src to minimize damaged area
v8:
- adjust pipe_damaged area to 4 lines grouping
- adjust calculation now that is understood that uapi.src is the
framebuffer coordinates that plane will start to fetch from
v9:
- Only add plane dst or src to damaged_area if visible
- Early skip plane damage calculation if it was not visible in old and
new state
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-2-jose.souza@intel.com
Much more clear to read one function call than four lines doing this
conversion.
v7:
- function renamed
- calculating width and height before truncate
- inlined
v10:
- renamed parameters from source and destination to src and dst
to match sister functions
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210104205654.238928-1-jose.souza@intel.com
It doesn't seem like drm.h docs are included anywhere. Render them next
to drm_mode.h, under the "Userspace API Structures" section.
This also allows references to e.g. DRM_CAP_* to be properly linkified
elsewhere in our docs.
Signed-off-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222133524.160842-6-contact@emersion.fr
Sphinx doesn't like old doc-comments in drm.h and generates warnings
like:
./include/uapi/drm/drm.h:87: warning: cannot understand function prototype: 'struct drm_clip_rect '
./include/uapi/drm/drm.h:97: warning: cannot understand function prototype: 'struct drm_drawable_info '
./include/uapi/drm/drm.h:105: warning: cannot understand function prototype: 'struct drm_tex_region '
...
Demote these to regular comments, because converting all of them is
quite a lot of work (also requires documenting all of the struct fields
for instance). Also many of these structures aren't really used by
modern user-space.
We can easily convert these remaining old comments to Sphinx style on a
one-by-one basis.
Signed-off-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222133524.160842-5-contact@emersion.fr
Our documentation build system chokes on \file comments:
./include/uapi/drm/drm.h:2: warning: Cannot understand * \file drm.h
on line 2 - I thought it was a doc line
Remove all of the slash-directives, and demote to a normal comment. Keep
the historical information because it predates Git.
v3: keep the comment (Daniel)
Signed-off-by: Simon Ser <contact@emersion.fr>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201222133524.160842-4-contact@emersion.fr
In generating the reference LRC, we want a page-aligned address for
simplicity in computing the offsets within. This then shares the
computation for the HW LRC which is mapped and so page aligned, making
the comparison straightforward. It seems that kmalloc(4k) is not always
returning from a 4k-aligned slab cache (which would give us a page aligned
address) so force alignment by explicitly allocating a page.
Reported-by: "Gote, Nitin R" <nitin.r.gote@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Gote, Nitin R" <nitin.r.gote@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923114156.17749-1-chris@chris-wilson.co.uk
Here's another variant PNY Pro Elite USB 3.1 Gen 2 portable SSD that
hangs and doesn't respond to ATA_1x pass-through commands. If it doesn't
support these commands, it should respond properly to the host. Add it
to the unusual uas list to be able to move forward with other
operations.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2edc7af892d0913bf06f5b35e49ec463f03d5ed8.1609819418.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With GNU binutils 2.35+, linking with BFD produces warnings for vmlinux:
aarch64-linux-gnu-ld: warning: -z norelro ignored
BFD can produce this warning when the target emulation mode does not
support RELRO program headers, and -z relro or -z norelro is passed.
Alan Modra clarifies:
The default linker emulation for an aarch64-linux ld.bfd is
-maarch64linux, the default for an aarch64-elf linker is
-maarch64elf. They are not equivalent. If you choose -maarch64elf
you get an emulation that doesn't support -z relro.
The ARCH=arm64 kernel prefers -maarch64elf, but may fall back to
-maarch64linux based on the toolchain configuration.
LLD will always create RELRO program header regardless of target
emulation.
To avoid the above warning when linking with BFD, pass -z norelro only
when linking with LLD or with -maarch64linux.
Fixes: 3b92fa7485 ("arm64: link with -z norelro regardless of CONFIG_RELOCATABLE")
Fixes: 3bbd3db864 ("arm64: relocatable: fix inconsistencies in linker script and options")
Cc: <stable@vger.kernel.org> # 5.0.x-
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Quentin Perret <qperret@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Alan Modra <amodra@gmail.com>
Cc: Fāng-ruì Sòng <maskray@google.com>
Link: https://lore.kernel.org/r/20201218002432.788499-1-ndesaulniers@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add driver for the Qualcomm interconnect buses found in MSM8939 based
platforms. The topology consists of four NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-6-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The Qualcomm MSM8939 platform has several bus fabrics that could be
controlled and tuned dynamically according to the bandwidth demand.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201204075345.5161-5-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
MSM8916 and QCS404 bindings are almost identical, so combine them into one.
This will make it easier to add interconnect bindings for more SoC with RPM.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201204075345.5161-4-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Use shared code for aggregate functionalities and probe function
to remove duplicated code.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-3-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Add RPM based interconnect driver implements the set and aggregate
functionalities that translates bandwidth requests into RPM messages.
These modules provide a common set of functionalities for all
Qualcomm RPM based interconnect providers and should help reduce code
duplication when adding new providers.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20201204075345.5161-2-jun.nie@linaro.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
platform_device_unregister() is NULL-aware and thus doesn't required a
duplication check in i801_del_mux(). Besides that it's also error pointer
aware, and we may drop unneeded assignment in i801_add_mux() followed by
conversion to PTR_ERR_OR_ZERO() for the returned value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since gpiod_remove_lookup_table() is NULL-aware, no need to have this check
in the caller. Drop duplicate NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit
28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
introduced a new location where a pmd was released, but neglected to
run the pmd page destructor. In fact, this happened previously for a
different pmd release path and was fixed by commit:
c283610e44 ("x86, mm: do not leak page->ptl for pmd page tables").
This issue was hidden until recently because the failure mode is silent,
but commit:
b2b29d6d01 ("mm: account PMD tables like PTE tables")
turns the failure mode into this signature:
BUG: Bad page state in process lt-pmem-ns pfn:15943d
page:000000007262ed7b refcount:0 mapcount:-1024 mapping:0000000000000000 index:0x0 pfn:0x15943d
flags: 0xaffff800000000()
raw: 00affff800000000 dead000000000100 0000000000000000 0000000000000000
raw: 0000000000000000 ffff913a029bcc08 00000000fffffbff 0000000000000000
page dumped because: nonzero mapcount
[..]
dump_stack+0x8b/0xb0
bad_page.cold+0x63/0x94
free_pcp_prepare+0x224/0x270
free_unref_page+0x18/0xd0
pud_free_pmd_page+0x146/0x160
ioremap_pud_range+0xe3/0x350
ioremap_page_range+0x108/0x160
__ioremap_caller.constprop.0+0x174/0x2b0
? memremap+0x7a/0x110
memremap+0x7a/0x110
devm_memremap+0x53/0xa0
pmem_attach_disk+0x4ed/0x530 [nd_pmem]
? __devm_release_region+0x52/0x80
nvdimm_bus_probe+0x85/0x210 [libnvdimm]
Given this is a repeat occurrence it seemed prudent to look for other
places where this destructor might be missing and whether a better
helper is needed. try_to_free_pmd_page() looks like a candidate, but
testing with setting up and tearing down pmd mappings via the dax unit
tests is thus far not triggering the failure.
As for a better helper pmd_free() is close, but it is a messy fit
due to requiring an @mm arg. Also, ___pmd_free_tlb() wants to call
paravirt_tlb_remove_table() instead of free_page(), so open-coded
pgtable_pmd_page_dtor() seems the best way forward for now.
Debugged together with Matthew Wilcox <willy@infradead.org>.
Fixes: 28ee90fe60 ("x86/mm: implement free pmd/pte page interfaces")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/160697689204.605323.17629854984697045602.stgit@dwillia2-desk3.amr.corp.intel.com
The usual pattern for the remove calls, like gpiod_remove_lookup_table(),
is to be NULL-aware, i.o.w. become a no-op whenever parameter is NULL.
Update gpiod_remove_lookup_table() call to follow this pattern.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Decrease polling time 'MLXCPLD_I2C_POLL_TIME' from 2000 usec to 400
usec. It greatly improves performance of I2C transactions.
Reliability of setting polling time to 400 usec has been thoroughly
validated across all the supported systems.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c_new_client_device() already prints an error when it fails. Some
ACPI tables contain 2 ACPI devices describing the same i2c-client,
leading to errors like this:
[ 1.620847] i2c i2c-4: Failed to register i2c client MAGN0001:00 at 0x1d (-16)
[ 1.620870] i2c i2c-4: failed to add I2C device MAGN0001:00 from ACPI
There is nothing we can do about the first -EBUSY error being logged,
but the second error does not really add any new information, so lets
drop it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With the apdma remove hand-shake signal, it requirs special
operation timing to reset i2c manually, otherwise the interrupt
will not be triggered, i2c transmission will be timeout.
Fixes: 8426fe70cfa4("i2c: mediatek: Add apdma sync in i2c driver")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>