With commit 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
wMaxPacketSize is computed dynamically but the value is never reset.
Because of this, the actual maximum packet size can only decrease each time
the audio gadget is instantiated.
Reset the endpoint maximum packet size and mark wMaxPacketSize as dynamic
to solve the problem.
Fixes: 913e4a90b6 ("usb: gadget: f_uac2: finalize wMaxPacketSize according to bandwidth")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201221173531.215169-2-jbrunet@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First of all the commit e0082698b6 ("usb: dwc3: ulpi: conditionally
resume ULPI PHY") introduced the Suspend USB2.0 HS/FS/LS PHY regression,
as by design of the fix any attempt to read/write from/to the PHY control
registers will completely disable the PHY suspension, which consequently
will increase the USB bus power consumption. Secondly the fix won't work
well for the very first attempt of the ULPI PHY control registers IO,
because after disabling the USB2.0 PHY suspension functionality it will
still take some time for the bus to resume from the sleep state if one has
been reached before it. So the very first PHY register read/write
operation will take more time than the busy-loop provides and the IO
timeout error might be returned anyway.
Here we suggest to fix the denoted problems in the following way. First of
all let's not disable the Suspend USB2.0 HS/FS/LS PHY functionality so to
make the controller and the USB2.0 bus more power efficient. Secondly
instead of that we'll extend the PHY IO op wait procedure with 1 - 1.2 ms
sleep if the PHY suspension is enabled (1ms should be enough as by LPM
specification it is at most how long it takes for the USB2.0 bus to resume
from L1 (Sleep) state). Finally in case if the USB2.0 PHY suspension
functionality has been disabled on the DWC USB3 controller setup procedure
we'll compensate the USB bus resume process latency by extending the
busy-loop attempts counter.
Fixes: e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-4-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally the procedure of the ULPI transaction finish detection has been
developed as a simple busy-loop with just decrementing counter and no
delays. It's wrong since on different systems the loop will take a
different time to complete. So if the system bus and CPU are fast enough
to overtake the ULPI bus and the companion PHY reaction, then we'll get to
take a false timeout error. Fix this by converting the busy-loop procedure
to take the standard bus speed, address value and the registers access
mode into account for the busy-loop delay calculation.
Here is the way the fix works. It's known that the ULPI bus is clocked
with 60MHz signal. In accordance with [1] the ULPI bus protocol is created
so to spend 5 and 6 clock periods for immediate register write and read
operations respectively, and 6 and 7 clock periods - for the extended
register writes and reads. Based on that we can easily pre-calculate the
time which will be needed for the controller to perform a requested IO
operation. Note we'll still preserve the attempts counter in case if the
DWC USB3 controller has got some internals delays.
[1] UTMI+ Low Pin Interface (ULPI) Specification, Revision 1.1,
October 20, 2004, pp. 30 - 36.
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-3-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In accordance with [1] the DWC_usb3 core sets the GUSB2PHYACCn.VStsDone
bit when the PHY vendor control access is done and clears it when the
application initiates a new transaction. The doc doesn't say anything
about the GUSB2PHYACCn.VStsBsy flag serving for the same purpose. Moreover
we've discovered that the VStsBsy flag can be cleared before the VStsDone
bit. So using the former as a signal of the PHY control registers
completion might be dangerous. Let's have the VStsDone flag utilized
instead then.
[1] Synopsys DesignWare Cores SuperSpeed USB 3.0 xHCI Host Controller
Databook, 2.70a, December 2013, p.388
Fixes: 88bc9d194f ("usb: dwc3: add ULPI interface support")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210085008.13264-2-Sergey.Semin@baikalelectronics.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous change ("usb: dwc3: drd: Avoid error when extcon is
missing") changed the code flow in dwc3_get_extcon() function, leading
to unnecessary if-branch. This patch does housekeeping by reworking the
code for obtaining an extcon device from the "port" node.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20201214110741.8512-3-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If "port" node is missing in PHY controller node, dwc3_get_extcon()
isn't able to find extcon devices. This is perfectly fine in case when
"usb-role-switch" or OTG is used, but next misleading error message is
printed in that case, from of_graph_get_remote_node():
OF: graph: no port node found in /phy@1234abcd
Avoid printing that message by checking if the port node exists in PHY
node before calling of_graph_get_remote_node(). While at it, add the
comment from mentioned code block, explaining how checking the port
availability helps to avoid the misleading error.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20201214110741.8512-2-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous patches in this series have changed the behaviour of the
driver and added new calls.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-5-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new ioctl only returns the status byte (STB) that was originally
sent by the device due to a service request (SRQ) condition.
This ioctl checks the srq_asserted bit of the associated file
descriptor. If set, the srq_asserted bit is reset and the cached
STB with original SRQ information is returned. Otherwise the ioctl
returns the error code ENOMSG.
This ioctl is useful to support non USBTMC-488 compliant devices.
Time sensitive applications can read the cached STB without incurring
the cost of an urb transaction over the bus.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new ioctl reads the status byte (STB) from the device and returns
the STB unmodified to the application. The srq_asserted bit is not taken
into account and not changed.
This ioctl is useful to support non USBTMC-488 compliant devices.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ioctl USBTMC488_IOCTL_READ_STB either returns a cached status byte
(STB) sent by the device due to a service request (SRQ) condition or
the STB obtained from a query to the device with a READ_STATUS_BYTE
control message.
When the query is interrupted by an SRQ message on the interrupt pipe,
the ioctl still returns the requested STB while the STB of the
out-of-band SRQ message is cached for the next call of this
ioctl. However the cached SRQ STB represents a state that was previous
to the last returned STB. Furthermore the cached SRQ STB can be stale
and not reflect the current state of the device.
The fixed ioctl now always reads the STB from the device and if the
associated file descriptor has the srq_asserted bit set it ors in the
RQS bit to the returned STB and clears the srq_asserted bit conformant
to subclass USB488 devices.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add kcov_remote_start()/kcov_remote_stop() annotations to the
vhci_rx_loop() function, which is responsible for parsing USB/IP packets
coming into USB/IP client.
Since vhci_rx_loop() threads are spawned per vhci_hcd device instance, the
common kcov handle is used for kcov_remote_start()/stop() annotations
(see Documentation/dev-tools/kcov.rst for details). As the result kcov
can now be used to collect coverage from vhci_rx_loop() threads.
Co-developed-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Nazime Hande Harputluoglu <handeharputlu@google.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/f8114050f8d65aa0bc801318b1db532d9f432447.1606175386.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to always cancel the control URB in write() so that it can be
reused after a timeout or spurious CMD_ACK.
Currently any further write requests after a timeout would fail after
triggering a WARN() in usb_submit_urb() when attempting to submit the
already active URB.
Reported-by: syzbot+e87ebe0f7913f71f2ea5@syzkaller.appspotmail.com
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if of_find_device_by_node() succeed, usbmisc_get_init_data() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: ef12da914e ("usb: chipidea: imx: properly check for usbmisc")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201117011430.642589-1-yukuai3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the MTU size issue with RX packet size as the host sends the packet
with extra bytes containing ethernet header. This causes failure when
user sets the MTU size to the maximum i.e. 15412. In this case the
ethernet packet received will be of length 15412 plus the ethernet header
length. This patch fixes the issue where there is a check that RX packet
length must not be more than max packet length.
Fixes: bba787a860 ("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1605597215-122027-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spinlock lockup as part of composite_disconnect
when it tries to acquire cdev->lock as part of usb_gadget_deactivate.
This is because the usb_gadget_deactivate is called from
usb_function_deactivate with the same spinlock held.
This would result in the below call stack and leads to stall.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 3-...0: (1 GPs behind) idle=162/1/0x4000000000000000
softirq=10819/10819 fqs=2356
(detected by 2, t=5252 jiffies, g=20129, q=3770)
Task dump for CPU 3:
task:uvc-gadget_wlhe state:R running task stack: 0 pid: 674 ppid:
636 flags:0x00000202
Call trace:
__switch_to+0xc0/0x170
_raw_spin_lock_irqsave+0x84/0xb0
composite_disconnect+0x28/0x78
configfs_composite_disconnect+0x68/0x70
usb_gadget_disconnect+0x10c/0x128
usb_gadget_deactivate+0xd4/0x108
usb_function_deactivate+0x6c/0x80
uvc_function_disconnect+0x20/0x58
uvc_v4l2_release+0x30/0x88
v4l2_release+0xbc/0xf0
__fput+0x7c/0x230
____fput+0x14/0x20
task_work_run+0x88/0x140
do_notify_resume+0x240/0x6f0
work_pending+0x8/0x200
Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate
call from usb_function_deactivate.
The same lockup can happen in the usb_gadget_activate path. Fix that path
as well.
Reported-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When printer driver is loaded, the printer_func_bind function is called, in
this function, the interface descriptor be allocated memory, if after that,
the error occurred, the interface descriptor memory need to be free.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Link: https://lore.kernel.org/r/20201210020148.6691-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warm reboot scenarios some times type C Mux driver gets Mux configuration
request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure
Mux as follows as per IOM requirement:
(1). Confgiure Mux HPD = 1, IRQ = 0
(2). Configure Mux with HPD = 1, IRQ = 1
IOM expects TypeC Mux configuration as follows:
(1). HPD=1, IRQ=0
(2). HPD=1, IRQ=1
if IOM gets mux config request (2) without configuring (1), it will ignore
the request. The impact of this is there is no DP_alt mode display.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting UAF at usb_submit_urb() [1], for
service_outstanding_interrupt() is not checking WDM_DISCONNECTING
before calling usb_submit_urb(). Close the race by doing same checks
wdm_read() does upon retry.
Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held,
service_interrupt_work() does not hold desc->rlock. Thus, it is possible
that usb_submit_urb() is called from service_outstanding_interrupt() from
service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs()
from wdm_disconnect() completed. Thus, move kill_urbs() in
wdm_disconnect() to after cancel_work_sync() (which makes sure that
service_interrupt_work() is no longer running) completed.
Although it seems to be safe to dereference desc->intf->dev in
service_outstanding_interrupt() even if WDM_DISCONNECTING was already set
because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from
reaching list_del() before service_outstanding_interrupt() completes,
let's not emit error message if WDM_DISCONNECTING is set by
wdm_disconnect() while usb_submit_urb() is in progress.
[1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661daf
Reported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, and this driver
was only used by the old non-DT i.MX devices.
Remove the driver as it has no users left.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201210210413.15262-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add compatible string in j721e-usb binding file as the same USB subsystem
is present in AM64.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20201215042549.7956-1-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is supported by the IR Toy driver.
Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201227134502.4548-2-sean@mess.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add --buildid-mmap option to enable build id in PERF_RECORD_MMAP2 events.
It will only work if there's kernel support for that and it disables
build id cache (implies --no-buildid).
It's also possible to enable it permanently via config option in
~/.perfconfig file:
[record]
build-id=mmap
Also added build_id bit in the verbose output for perf_event_attr:
# perf record --buildid-mmap -vv
...
perf_event_attr:
type 1
size 120
...
build_id 1
Adding also missing text_poke bit.
Committer testing:
$ perf record -h build
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-B, --no-buildid do not collect buildids in perf.data
-N, --no-buildid-cache
do not update the buildid cache
--buildid-all Record build-id of all DSOs regardless of hits
--buildid-mmap Record build-id in map events
$
$ perf record --buildid-mmap sleep 1
Failed: no support to record build id in mmap events, update your kernel.
$
After adding the needed kernel bits in a test kernel:
$ perf record -vv --buildid-mmap sleep 1 |& grep -m1 build
Enabling build id in mmap2 events.
$ perf evlist -v
cycles:u: size: 120, { sample_period, sample_freq }: 4000, sample_type: IP|TID|TIME|PERIOD, read_format: ID, disabled: 1, inherit: 1, exclude_kernel: 1, mmap: 1, comm: 1, freq: 1, enable_on_exec: 1, task: 1, sample_id_all: 1, exclude_guest: 1, mmap2: 1, comm_exec: 1, ksymbol: 1, bpf_event: 1, build_id: 1
$
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Budankov <abudankov@huawei.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20201214105457.543111-16-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The ThinkPad X395 latop does not have the internal digital
microphone connected to the AMD's ACP bridge, but it's advertised
via BIOS. The internal microphone is connected to the HDA codec.
Use DMI to block the microphone PCM device for this platform.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1892115
Cc: <stable@kernel.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20201227164109.269973-1-perex@perex.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
When we try to play and capture simultaneously we see that
interrupts are genrated but our handler is not being acknowledged,
After investigating further more in detail on this issue we found
that IRQ delivery via MSI from the ACP IP is unreliable and so sometimes
interrupt generated will not be acknowledged so MSI model shouldn't be used
and using legacy IRQs will resolve interrupt handling issue.
This patch replaces MSI interrupt handling with legacy IRQ model.
Issue can be reproduced easily by running below python script:
import subprocess
import time
import threading
def do2():
cmd = 'aplay -f dat -D hw:2,1 /dev/zero -d 1'
subprocess.call(cmd, stdin=subprocess.PIPE,
stderr=subprocess.PIPE, shell=True)
print('Play Done')
def run():
for i in range(1000):
do2()
def do(i):
cmd = 'arecord -f dat -D hw:2,2 /dev/null -d 1'
subprocess.call(cmd, stdout=subprocess.PIPE,
stderr=subprocess.PIPE, shell=True)
print(datetime.datetime.now(), i)
t = threading.Thread(target=run)
t.start()
for i in range(1000):
do(i)
t.join()
After applying this patch issue is resolved.
Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com>
Link: https://lore.kernel.org/r/20201222115929.11222-1-Vishnuvardhanrao.Ravulapati@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following a change to the SPI framework, providing a value of zero for
'spi-rx-bus-width' and 'spi-tx-bus-width' is now possible and will
essentially mean that no RX or TX is allowed.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-3-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Transmit/receive only is a valid SPI mode. For example, the MOSI/TX line
might be missing from an ADC while for a DAC the MISO/RX line may be
optional. This patch adds these two new modes: SPI_NO_TX and
SPI_NO_RX. This way, the drivers will be able to identify if any of
these two lines is missing and to adjust the transfers accordingly.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-2-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This change moves all the SPI mode bits into a separate 'spi.h' header in
uAPI. This is meant to re-use these definitions inside the kernel as well
as export them to userspace (via uAPI).
The SPI mode definitions have usually been duplicated between between
'include/linux/spi/spi.h' and 'include/uapi/linux/spi/spidev.h', so
whenever adding a new entry, this would need to be put in both headers.
They've been moved from 'include/linux/spi/spi.h', since that seems a bit
more complete; the bits have descriptions and there is the SPI_MODE_X_MASK.
This change also does a conversion of these bitfields to _BITUL() macro.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201221152936.53873-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ThinkPad E14 Gen 2 latop does not have the internal digital
microphone connected to the AMD's ACP bridge, but it's advertised
via BIOS. The internal microphone is connected to the HDA codec.
Use DMI to block the microphone PCM device for this platform.
Reported-by: Eliot Blennerhassett <eliot@blennerhassett.gen.nz>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20201227164037.269893-1-perex@perex.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
If an error occurs after calling 'mtk_hsdma_init()', it must be undone by
a corresponding call to 'mtk_hsdma_uninit()' as already done in the
remove function.
Fixes: 0853c7a53e ("staging: mt7621-dma: ralink: add rt2880 dma engine")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201213153513.138723-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EFAULT on error instead of the number of bytes remaining to be
copied.
Fixes: bac42fb212 ("comedi: get rid of compat_alloc_user_space() mess in COMEDI_CMD{,TEST} compat")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/X8c3pfwFy2jpy4BP@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IN the probe function, if an error occurs after calling
'spmi_controller_alloc()', it must be undone by a corresponding
'spmi_controller_put() call.
In the remove function, use 'spmi_controller_put(ctrl)' instead of
'kfree(ctrl)'.
While a it fix an error message
(s/spmi_add_controller/spmi_controller_add/)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201213151105.137731-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are certain conditional expressions in rtl8192e, where a boolean
variable is compared with true/false, in forms such as (foo == true) or
(false != bar), which does not comply with checkpatch.pl (CHECK:
BOOL_COMPARISON), according to which boolean variables should be
themselves used in the condition, rather than comparing with true/false
E.g. in drivers/staging/rtl8192e/rtl8192e/r8192E_dev.c,
"if (Type == true)" can be replaced with: "if (Type)"
Replace all such expressions with the bool variables appropriately
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20201220194224.12835-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When fw_core_add_address_handler() fails, we need to destroy
the port by tty_port_destroy(). Also we need to unregister
the address handler by fw_core_remove_address_handler() on
failure.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20201221122437.10274-1-dinghao.liu@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an allocation for priv->rx_urb[16] has no null check,
which may lead to a null pointer dereference.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20201226080258.6576-1-dinghao.liu@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex lock can be initialized automatically with DEFINE_MUTEX()
rather than explicitly calling mutex_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201224132528.31558-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex lock can be initialized automatically with DEFINE_MUTEX()
rather than explicitly calling mutex_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201224132519.31504-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix all the braces coding style issues found by checkpatch.pl in
rtw_security.c.
Signed-off-by: Brother Matthew De Angelis <matthew.v.deangelis@gmail.com>
Link: https://lore.kernel.org/r/20201211222845.GA543167@a
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SLAB_RECLAIM_ACCOUNT to ashmem_range cache since it has registered
shrinker, which make memAvailable more presiced.
Acked-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Link: https://lore.kernel.org/r/1608277668-3740-1-git-send-email-huangzhaoyang@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding build id to synthesized mmap2 events for everything -
kernel/modules/tasks, when symbol_conf.buildid_mmap2 is true.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Budankov <abudankov@huawei.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20201214105457.543111-11-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Allow using PERF_RECORD_MMAP2 to synthesize the kernel modules maps so
that we can use PERF_RECORD_MMAP2 to encode the kernel modules build ids
in the following csets.
It's enabled by a new symbol_conf.buildid_mmap2 bool field, which will
be switchable in following changes.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Budankov <abudankov@huawei.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20201214105457.543111-10-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>