When setting xfrm replay_window to values higher than 32, a rare
page-fault occurs in xfrm_replay_advance_bmp:
BUG: unable to handle page fault for address: ffff8af350ad7920
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD ad001067 P4D ad001067 PUD 0
Oops: 0002 [#1] SMP PTI
CPU: 3 PID: 30 Comm: ksoftirqd/3 Kdump: loaded Not tainted 5.4.52-050452-generic #202007160732
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
RIP: 0010:xfrm_replay_advance_bmp+0xbb/0x130
RSP: 0018:ffffa1304013ba40 EFLAGS: 00010206
RAX: 000000000000010d RBX: 0000000000000002 RCX: 00000000ffffff4b
RDX: 0000000000000018 RSI: 00000000004c234c RDI: 00000000ffb3dbff
RBP: ffffa1304013ba50 R08: ffff8af330ad7920 R09: 0000000007fffffa
R10: 0000000000000800 R11: 0000000000000010 R12: ffff8af29d6258c0
R13: ffff8af28b95c700 R14: 0000000000000000 R15: ffff8af29d6258fc
FS: 0000000000000000(0000) GS:ffff8af339ac0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff8af350ad7920 CR3: 0000000015ee4000 CR4: 00000000001406e0
Call Trace:
xfrm_input+0x4e5/0xa10
xfrm4_rcv_encap+0xb5/0xe0
xfrm4_udp_encap_rcv+0x140/0x1c0
Analysis revealed offending code is when accessing:
replay_esn->bmp[nr] |= (1U << bitnr);
with 'nr' being 0x07fffffa.
This happened in an SMP system when reordering of packets was present;
A packet arrived with a "too old" sequence number (outside the window,
i.e 'diff > replay_window'), and therefore the following calculation:
bitnr = replay_esn->replay_window - (diff - pos);
yields a negative result, but since bitnr is u32 we get a large unsigned
quantity (in crash dump above: 0xffffff4b seen in ecx).
This was supposed to be protected by xfrm_input()'s former call to:
if (x->repl->check(x, skb, seq)) {
However, the state's spinlock x->lock is *released* after '->check()'
is performed, and gets re-acquired before '->advance()' - which gives a
chance for a different core to update the xfrm state, e.g. by advancing
'replay_esn->seq' when it encounters more packets - leading to a
'diff > replay_window' situation when original core continues to
xfrm_replay_advance_bmp().
An attempt to fix this issue was suggested in commit bcf66bf54a
("xfrm: Perform a replay check after return from async codepaths"),
by calling 'x->repl->recheck()' after lock is re-acquired, but fix
applied only to asyncronous crypto algorithms.
Augment the fix, by *always* calling 'recheck()' - irrespective if we're
using async crypto.
Fixes: 0ebea8ef35 ("[IPSEC]: Move state lock into x->type->input")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Fix passing of the additional security info via version
operations. Force new open when getting SACL and avoid
reuse of files that were previously open without
sufficient privileges to access SACLs.
Signed-off-by: Boris Protopopov <pboris@amazon.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Incorrect loop in error path of nft_set_elem_expr_clone(),
from Colin Ian King.
2) Missing xt_table_get_private_protected() to access table
private data in x_tables, from Subash Abhinov Kasiviswanathan.
3) Possible oops in ipset hash type resize, from Vasily Averin.
4) Fix shift-out-of-bounds in ipset hash type, also from Vasily.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: ipset: fix shift-out-of-bounds in htable_bits()
netfilter: ipset: fixes possible oops in mtype_resize
netfilter: x_tables: Update remaining dereference to RCU
netfilter: nftables: fix incorrect increment of loop counter
====================
Link: https://lore.kernel.org/r/20201218120409.3659-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most boards using the pcf2127 chip (in my bubble) don't make use of the
watchdog functionality and the respective output is not connected. The
effect on such a board is that there is a watchdog device provided that
doesn't work.
So only register the watchdog if the device tree has a "reset-source"
property.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[RV: s/has-watchdog/reset-source/]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201218101054.25416-3-rasmus.villemoes@prevas.dk
Some RTCs, e.g. the pcf2127, can be used as a hardware watchdog. But
if the reset pin is not actually wired up, the driver exposes a
watchdog device that doesn't actually work.
Provide a standard binding that can be used to indicate that a given
RTC can perform a reset of the machine, similar to wakeup-source.
Suggested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201218101054.25416-2-rasmus.villemoes@prevas.dk
taprio_graft() can insert a NULL element in the array of child qdiscs. As
a consquence, taprio_reset() might not reset child qdiscs completely, and
taprio_destroy() might leak resources. Fix it by ensuring that loops that
iterate over q->qdiscs[] don't end when they find the first NULL item.
Fixes: 44d4775ca5 ("net/sched: sch_taprio: reset child qdiscs before freeing them")
Fixes: 5a781ccbd1 ("tc: Add support for configuring the taprio scheduler")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/13edef6778fef03adc751582562fba4a13e06d6a.1608240532.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-12-17
Sylwester fixes an issue where PF was not properly being rebuilt
following VF removal for i40e.
Jakub Kicinski fixes a double release of rtnl_lock on
iavf_lan_add_device() error for iavf.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: fix double-release of rtnl_lock
i40e: Fix Error I40E_AQ_RC_EINVAL when removing VFs
====================
Link: https://lore.kernel.org/r/20201217223418.3134992-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a spelling mistake in the Kconfig help text. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201217171705.57586-1-colin.king@canonical.com
This reverts commit a63f23c9d139377833a139b179793fea79ee198f.
get_unaligned_{le16|le32|le64}(p) is meant to replace code of the form
le16_to_cpu(get_unaligned((__le16 *)p)). There is no need to explicitly
do leXX_to_cpu() if get_unaligned_leXX() is used.
https://lwn.net/Articles/277779/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables bcm driver to properly handle ISO packets.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If iter->count is 0 and iocb->ki_pos is page aligned, this causes
nr_pages to be 0.
Then in generic_file_buffered_read_get_pages() find_get_pages_contig()
returns 0 - because we asked for 0 pages, so we call
generic_file_buffered_read_no_cached_page() which attempts to add a page
to the page cache, which fails with -EEXIST, and then we loop. Oops...
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Reported-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Realtek RTL8822CE Bluetooth controller support Microsoft vendor
extension and it uses 0xFCF0 for VsMsftOpCode.
The following test step was performed.
- Boot the test device with RTL8822CE and verify the INFO print in
dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel JeffersonPeak, HarrisonPeak and CyclonePeak Bluetooth
controllers support the Microsoft vendor extension and they are using
0xFC1E for VsMsftOpCode.
< HCI Command: Vendor (0x3f|0x001e) plen 1
00
> HCI Event: Command Complete (0x0e) plen 15
Vendor (0x3f|0x001e) ncmd 1
Status: Success (0x00)
00 3f 00 00 00 00 00 00 00 01 50
The following test step was performed.
- Boot the test devices with HarrisonPeak and verify INFO print in
dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The following Qualcomm WCN399x Bluetooth controllers support the
Microsoft vendor extension and they are using 0xFD70 for VsMsftOpCode.
-WCN3990
-WCN3991
-WCN3998
< HCI Command: ogf 0x3f, ocf 0x0170, plen 1
00
> HCI Event: 0x0e plen 18
01 70 FD 00 00 1F 00 00 00 00 00 00 00 04 4D 53 46 54
The following test step was performed.
- Boot the device with WCN3991 and verify INFO print in dmesg.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Just like MGMT_OP_START_DISCOVERY, we should reject
MGMT_OP_START_SERVICE_DISCOVERY with MGMT_STATUS_BUSY when we are paused
for suspend.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
we should send hci reset command before bt turn off, which can reset bt
firmware status.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a missing SUSPEND_SCAN_ENABLE in passive scan, remove the separate
function for configuring le scan during suspend and update the request
complete function to clear both enable and disable tasks.
Fixes: dce0a4be80 ("Bluetooth: Set missing suspend task bits")
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In hci_uart_write_work, there is a loop/goto checking the value of
HCI_UART_TX_WAKEUP. If HCI_UART_TX_WAKEUP is set again, it keeps trying
hci_uart_dequeue; otherwise, it clears HCI_UART_SENDING and returns.
In hci_uart_tx_wakeup, if HCI_UART_SENDING is already set, it sets
HCI_UART_TX_WAKEUP, skips schedule_work and assumes the running/pending
hci_uart_write_work worker will do hci_uart_dequeue properly.
However, if the HCI_UART_SENDING check in hci_uart_tx_wakeup is done after
the loop breaks, but before HCI_UART_SENDING is cleared in
hci_uart_write_work, the schedule_work is skipped incorrectly.
Fix this race by changing the order of HCI_UART_SENDING and
HCI_UART_TX_WAKEUP modification.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: 82f5169bf3 ("Bluetooth: hci_uart: add serdev driver support library")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to read FW build version from debugfs node.
This info can be read from
/sys/kernel/debug/bluetooth/hci0/firmware_info
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
syzbot is feeding invalid superblock data to JFS for mount testing.
JFS does not check several of the fields -- just assumes that they
are good since the JFS_MAGIC and version fields are good.
In this case (syzbot reproducer), we have s_l2bsize == 0xda0c,
pad == 0xf045, and s_state == 0x50, all of which are invalid IMO.
Having s_l2bsize == 0xda0c causes this UBSAN warning:
UBSAN: shift-out-of-bounds in fs/jfs/jfs_mount.c:373:25
shift exponent -9716 is negative
s_l2bsize can be tested for correctness. pad can be tested for non-0
and punted. s_state can be tested for its valid values and punted.
Do those 3 tests and if any of them fails, report the superblock as
invalid/corrupt and let fsck handle it.
With this patch, chkSuper() says this when JFS_DEBUG is enabled:
jfs_mount: Mount Failure: superblock is corrupt!
Mount JFS Failure: -22
jfs_mount failed w/return code = -22
The obvious problem with this method is that next week there could
be another syzbot test that uses different fields for invalid values,
this making this like a game of whack-a-mole.
syzkaller link: https://syzkaller.appspot.com/bug?extid=36315852ece4132ec193
Reported-by: syzbot+36315852ece4132ec193@syzkaller.appspotmail.com
Reported-by: kernel test robot <lkp@intel.com> # v2
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: jfs-discussion@lists.sourceforge.net
When alt mode 6 is not available, fallback to the kernel <= 5.7 behavior
of always using alt mode 1.
Prior to kernel 5.8, btusb would always use alt mode 1 for WBS (Wide
Band Speech aka mSBC aka transparent SCO). In commit baac6276c0
("Bluetooth: btusb: handle mSBC audio over USB Endpoints") this
was changed to use alt mode 6, which is the recommended mode in the
Bluetooth spec (Specifications of the Bluetooth System, v5.0, Vol 4.B
§2.2.1). However, many if not most BT USB adapters do not support alt
mode 6. In fact, I have been unable to find any which do.
In kernel 5.8, this was changed to use alt mode 6, and if not available,
use alt mode 0. But mode 0 has a zero byte max packet length and can
not possibly work. It is just there as a zero-bandwidth dummy mode to
work around a USB flaw that would prevent device enumeration if
insufficient bandwidth were available for the lowest isoc mode
supported.
In effect, WBS was broken for all USB-BT adapters that do not support
alt 6, which appears to nearly all of them.
Then in commit 461f95f04f ("Bluetooth: btusb: USB alternate setting 1 for
WBS") the 5.7 behavior was restored, but only for Realtek adapters.
I've tested a Broadcom BRCM20702A and CSR 8510 adapter, both work with
the 5.7 behavior and do not with the 5.8.
So get rid of the Realtek specific flag and use the 5.7 behavior for all
adapters as a fallback when alt 6 is not available. This was the
kernel's behavior prior to 5.8 and I can find no adapters for which it
is not correct. And even if there is an adapter for which this does not
work, the current behavior would be to fall back to alt 0, which can not
possibly work either, and so is no better.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some resource should be released in the error handling path of the probe
function, as already done in the remove function.
The remove function was fixed in commit 5052de8def ("soc: qcom: smd:
Transition client drivers from smd to rpmsg")
Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The binding should use "unevaluatedProperties" instead of
"additionalProperties", since it is a SPI device and may have
SPI-related Device Tree properties, for instance the "spi-max-frequency"
property that is present in the example.
Fixes: e366a644c6 ("dt-bindings: display: Add ABT Y030XX067A panel bindings")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/20201217005945.335111-1-paul%40crapouillou.net
Signed-off-by: Rob Herring <robh@kernel.org>
Eliminate the following yamllint warnings:
./Documentation/devicetree/bindings/clock/imx8qxp-lpcg.yaml
:32:13:[warning] wrong indentation: expected 14 but found 12 (indentation)
:35:9: [warning] wrong indentation: expected 10 but found 8 (indentation)
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20201207045527.1607-2-thunder.leizhen@huawei.com
Signed-off-by: Rob Herring <robh@kernel.org>
Eliminate the following yamllint warnings:
./Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml
:52:9: [warning] wrong indentation: expected 6 but found 8 (indentation)
./Documentation/devicetree/bindings/display/bridge/intel,keembay-dsi.yaml
:42:8: [warning] wrong indentation: expected 8 but found 7 (indentation)
:45:8: [warning] wrong indentation: expected 8 but found 7 (indentation)
./Documentation/devicetree/bindings/display/intel,keembay-msscam.yaml
:21:6: [warning] wrong indentation: expected 6 but found 5 (indentation)
./Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
:25:10: [warning] wrong indentation: expected 10 but found 9 (indentation)
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201207044830.1551-2-thunder.leizhen@huawei.com
Signed-off-by: Rob Herring <robh@kernel.org>
When I do dt_binding_check for any YAML file, below wanring is always
reported:
xxx/soc/mediatek/devapc.yaml: 'additionalProperties' is a required property
xxx/soc/mediatek/devapc.yaml: ignoring, error in schema:
warning: no schema found in file: xxx/soc/mediatek/devapc.yaml
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201204093813.1275-5-thunder.leizhen@huawei.com
Signed-off-by: Rob Herring <robh@kernel.org>
When I do dt_binding_check for any YAML file, below wanring is always
reported:
xxx/soc/litex/litex,soc-controller.yaml: 'additionalProperties' is a required property
xxx/soc/litex/litex,soc-controller.yaml: ignoring, error in schema:
warning: no schema found in file: xxx/soc/litex/litex,soc-controller.yaml
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201204093813.1275-4-thunder.leizhen@huawei.com
Signed-off-by: Rob Herring <robh@kernel.org>
When I do dt_binding_check for any YAML file, below wanring is always
reported:
xxx/serial/litex,liteuart.yaml: 'additionalProperties' is a required property
xxx/serial/litex,liteuart.yaml: ignoring, error in schema:
warning: no schema found in file: xxx/serial/litex,liteuart.yaml
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201204093813.1275-3-thunder.leizhen@huawei.com
Signed-off-by: Rob Herring <robh@kernel.org>
When running make dt_binding_check, the xlnx,vcu-settings binding
triggers the following two warnings:
'additionalProperties' is a required property
example-0: vcu@a0041000:reg:0: [0, 2684620800, 0, 4096] is too long
Fix the binding and make the checker happy.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201202090522.251607-1-m.tretter@pengutronix.de
Signed-off-by: Rob Herring <robh@kernel.org>
'additionalProperties' is now required by the meta-schema. Add it for
coda. As a result, 'interrupts', 'interrupt-names' and 'power-domains'
need to be reworked to be defined at the top level.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20201117200752.4004368-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The correct syntax for JSON pointers begins with a '/' after the '#'.
Without a '/', the string should be interpreted as a subschema
identifier. The jsonschema module currently doesn't handle subschema
identifiers and incorrectly allows JSON pointers to begin without a '/'.
Let's fix this before it becomes a problem when jsonschema module is
fixed.
Converted with:
perl -p -i -e 's/yaml#definitions/yaml#\/definitions/g' `find Documentation/devicetree/bindings/ -name "*.yaml"`
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: netdev@vger.kernel.org
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20201217223429.354283-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
vdpa doesn't have any specific need to define start and end range of the
device index.
Hence use the simper version of the ida allocator.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20201112064005.349268-3-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add missing comment for number of virtqueue.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20201112064005.349268-2-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The OASIS virtio spec (1.1) defines several IDs that aren't reflected
in the header yet. Fixing this by adding the missing IDs, even though
they're not yet used by the kernel yet.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Link: https://lore.kernel.org/r/20201202111931.31953-2-info@metux.net
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixing the differing indentions to be consistent and properly aligned.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Link: https://lore.kernel.org/r/20201202111931.31953-1-info@metux.net
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 25b98b64e2 ("vhost scsi: alloc cmds per vq instead of session")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1607071411-33484-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "vq" struct is added to the "vdev->vqs" list prematurely. If we
encounter an error later in the function then the "vq" is freed, but
since it is still on the list that could lead to a use after free bug.
Fixes: cbeedb72b9 ("virtio_ring: allocate desc state for split ring separately")
Reported-by: Robert Buhren <robert.buhren@sect.tu-berlin.de>
Reported-by: Felicitas Hetzelt <file@sect.tu-berlin.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8pGaG/zkI3jk8mk@mwanda
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Set a negative error code intead of returning success if the MTU has
been changed to something invalid.
Fixes: fe36cbe067 ("virtio_net: clear MTU when out of range")
Reported-by: Robert Buhren <robert.buhren@sect.tu-berlin.de>
Reported-by: Felicitas Hetzelt <file@sect.tu-berlin.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8pGVJSeeCdII1Ys@mwanda
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
There is a copy and paste bug in the error handling of this code and
it uses "ring_dma_addr" three times instead of "device_event_dma_addr"
and "driver_event_dma_addr".
Fixes: 1ce9e6055f (" virtio_ring: introduce packed ring support")
Reported-by: Robert Buhren <robert.buhren@sect.tu-berlin.de>
Reported-by: Felicitas Hetzelt <file@sect.tu-berlin.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8pGRJlEzyn+04u2@mwanda
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
krealloc_array is used in drivers/vhost/vringh.c, add it to avoid build
failure.
Drop WARN_ON_ONCE, because duplicated with the one in bug.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20201209084205.24062-3-peng.fan@oss.nxp.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make sure to put dma write memory barrier after updating CQ consumer
index so the hardware knows that there are available CQE slots in the
queue.
Failure to do this can cause the update of the RX doorbell record to get
updated before the CQ consumer index resulting in CQ overrun.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Link: https://lore.kernel.org/r/20201209140004.15892-1-elic@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce new vdpa_sim_net and vdpa_sim (core) drivers. This is a
preparation for adding a vdpa simulator module for block devices.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
[sgarzare: various cleanups/fixes]
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20201215144256.155342-19-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vringh_getdesc_iotlb() manages 2 iovs for writable and readable
descriptors. This is very useful for the block device, where for
each request we have both types of descriptor.
Let's split the vdpasim_virtqueue's iov field in out_iov and
in_iov to use them with vringh_getdesc_iotlb().
We are using VIRTIO terminology for "out" (readable by the device)
and "in" (writable by the device) descriptors.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20201215144256.155342-18-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow each device to specify the size of the buffer allocated
in vdpa_sim.
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20201215144256.155342-17-sgarzare@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>