Commit 801954d121 ("serial: 8250: 8250_omap: Support native RS485")
calculates RS485 delays from the baudrate. The baudrate is generated
with either a 16x or 13x divisor. The divisor is set in the Mode
Definition Register 1 (MDR1).
The commit erroneously assumes that the register stores the divisor as
a bitmask and uses a logical AND to differentiate between 16x and 13x
divisors. However the divisor is really stored as a 3-bit mode
(see lines 363ff in include/uapi/linux/serial_reg.h).
The logical AND operation is performed with UART_OMAP_MDR1_16X_MODE,
which is defined as 0x0 and hence yields false. So the commit always
assumes a 13x divisor. Fix by using an equal comparison. This works
because we never set any of the other 5 bits in the register. (They
pertain to IrDA mode, which is not supported by the driver).
Fixes: 801954d121 ("serial: 8250: 8250_omap: Support native RS485")
Link: https://lore.kernel.org/linux-serial/202211070440.8hWunFUN-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/7d5b04da13d89b8708b9543a0b125f2b6062a77b.1667977259.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A problem about 8250_bcm7271 create debugfs failed is triggered with the
following log given:
[ 324.516635] debugfs: Directory 'bcm7271-uart' with parent '/' already present!
The reason is that brcmuart_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of 8250_bcm7271 can never be created later.
brcmuart_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221109072110.117291-2-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA Rx completes, the current behavior is to just exit the DMA
completion handler without future actions. If the transfer is still
on-going, UART will trigger an interrupt and that eventually rearms the
DMA Rx. The extra interrupt round-trip has an inherent latency cost
that increases the risk of FIFO overrun. In such situations, the
latency margin tends to already be less due to FIFO not being empty.
Add check into DMA Rx completion handler to detect if LSR has DR (Data
Ready) still set. DR indicates there will be more characters pending
and DMA Rx can be rearmed right away to handle them.
Cc: Gilles BULOZ <gilles.buloz@kontron.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221107102126.56481-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the two instances of this typo present in the MSM and VT8500 serial
drivers.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20221104103719.2234098-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct tty_buffer has flags which is only used for storing TTYB_NORMAL.
There is also a few quite confusing operations for checking the presense
of TTYB_NORMAL. Simplify things by converting flags to bool.
Despite the name remaining the same, the meaning of "flags" is altered
slightly by this change. Previously it referred to flags of the buffer
(only TTYB_NORMAL being used as a flag). After this change, flags tell
whether the buffer contains/should be allocated with flags array along
with character data array. It is much more suitable name that
TTYB_NORMAL was for this purpose, thus the name remains.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019105504.16800-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though our EFI zboot decompressor is pedantically spec compliant
and idiomatic for EFI image loaders, calling LoadImage() and
StartImage() for the nested image is a bit of a burden. Not only does it
create workflow issues for the distros (as both the inner and outer
PE/COFF images need to be signed for secure boot), it also copies the
image around in memory numerous times:
- first, the image is decompressed into a buffer;
- the buffer is consumed by LoadImage(), which copies the sections into
a newly allocated memory region to hold the executable image;
- once the EFI stub is invoked by StartImage(), it will also move the
image in memory in case of KASLR, mirrored memory or if the image must
execute from a certain a priori defined address.
There are only two EFI spec compliant ways to load code into memory and
execute it:
- use LoadImage() and StartImage(),
- call ExitBootServices() and take ownership of the entire system, after
which anything goes.
Given that the EFI zboot decompressor always invokes the EFI stub, and
given that both are built from the same set of objects, let's merge the
two, so that we can avoid LoadImage()/StartImage but still load our
image into memory without breaking the above rules.
This also means we can decompress the image directly into its final
location, which could be randomized or meet other platform specific
constraints that LoadImage() does not know how to adhere to. It also
means that, even if the encapsulated image still has the EFI stub
incorporated as well, it does not need to be signed for secure boot when
wrapping it in the EFI zboot decompressor.
In the future, we might decide to retire the EFI stub attached to the
decompressed image, but for the time being, they can happily coexist.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The LoongArch build of the EFI stub is part of the core kernel image, and
therefore accesses section markers directly when it needs to figure out
the size of the various section.
The zboot decompressor does not have access to those symbols, but
doesn't really need that either. So let's move handle_kernel_image()
into a separate file (or rather, move everything else into a separate
file) so that the zboot build does not pull in unused code that links to
symbols that it does not define.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Currently, the EFI entry code for LoongArch is set up to copy the
executable image to the preferred offset, but instead of branching
directly into that image, it branches to the local copy of kernel_entry,
and relies on the logic in that function to switch to the link time
address instead.
This is a bit sloppy, and not something we can support once we merge the
EFI decompressor with the EFI stub. So let's clean this up a bit, by
adding a helper that computes the offset of kernel_entry from the start
of the image, and simply adding the result to VMLINUX_LOAD_ADDRESS.
And considering that we cannot execute from anywhere else anyway, let's
avoid efi_relocate_kernel() and just allocate the pages instead.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The arm64 build of the EFI stub is part of the core kernel image, and
therefore accesses section markers directly when it needs to figure out
the size of the various section.
The zboot decompressor does not have access to those symbols, but
doesn't really need that either. So let's move handle_kernel_image()
into a separate file (or rather, move everything else into a separate
file) so that the zboot build does not pull in unused code that links to
symbols that it does not define.
While at it, introduce a helper routine that the generic zboot loader
will need to invoke after decompressing the image but before invoking
it, to ensure that the I-side view of memory is consistent.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The RISC-V build of the EFI stub is part of the core kernel image, and
therefore accesses section markers directly when it needs to figure out
the size of the various section.
The zboot decompressor does not have access to those symbols, but
doesn't really need that either. So let's move handle_kernel_image()
into a separate file (or rather, move everything else into a separate
file) so that the zboot build does not pull in unused code that links to
symbols that it does not define.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Factor out the expressions that describe the preferred placement of the
loaded image as well as the minimum alignment so we can reuse them in
the decompressor.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In order to be able to switch from LoadImage() [which treats the
supplied PE/COFF image as file input only, and reconstructs the memory
image based on the section descriptors] to a mode where we allocate the
memory directly, and invoke the image in place, we need to now how much
memory to allocate beyond the end of the image. So copy this information
from the payload's PE/COFF header to the end of the compressed version
of the payload, so that the decompressor app can access it before
performing the decompression itself.
We'll also need to size of the code region once we switch arm64 to
jumping to the kernel proper with MMU and caches enabled, so let's
capture that information as well. Note that SizeOfCode does not account
for the header, so we need SizeOfHeaders as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In preparation for allowing the EFI zboot decompressor to reuse most of
the EFI stub machinery, factor out the actual EFI PE/COFF entrypoint
into a separate file.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Clone the implementations of strrchr() and memchr() in lib/string.c so
we can use them in the standalone zboot decompressor app. These routines
are used by the FDT handling code.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Currently, arm64, RISC-V and LoongArch rely on the fact that struct
screen_info can be accessed directly, due to the fact that the EFI stub
and the core kernel are part of the same image. This will change after a
future patch, so let's ensure that the screen_info handling is able to
deal with this, by adopting the arm32 approach of passing it as a
configuration table. While at it, switch to ACPI reclaim memory to hold
the screen_info data, which is more appropriate for this kind of
allocation.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Drop the __efistub_ prefixed exports of various routines that the EFI
stub on LoongArch does not even use.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Split the efi_printk() routine into its own source file, and provide
local implementations of strlen() and strnlen() so that the standalone
zboot app can efi_err and efi_info etc.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
We will no longer be able to call into the kernel image once we merge
the decompressor with the EFI stub, so we need our own implementation of
memcmp(). Let's add the one from lib/string.c and simplify it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In preparation for moving the EFI stub functionality into the zboot
decompressor, switch to the stub's implementation of strncmp()
unconditionally.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Commit 6ed27461c9c8 ("arm64: efi: Move efi-entry.S into the libstub source
directory") moves arch/arm64/kernel/efi-entry.S to
drivers/firmware/efi/libstub/arm64-entry.S, but misses to adjust the
MAINTAINERS file.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken file pattern.
Adjust the file entry in EXTENSIBLE FIRMWARE INTERFACE (EFI) to this file
movement.
As the file drivers/firmware/efi/libstub/arm64-entry.S is already covered
by the entry drivers/firmware/efi/, simply remove the arm64 file entry.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
We will be sharing efi-entry.S with the zboot decompressor build, which
does not link against vmlinux directly. So move it into the libstub
source directory so we can include in the libstub static library.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
To allow efi_enter_kernel() to be shared with the EFI zboot decompressor
build, drop another reference to dcache_clean_poc() and replace it with
a single DC CVAC* instruction. To ensure that it covers the remainder of
efi_enter_kernel() as intended, reorganize the code a bit so it fits in
a 32-byte cacheline, and align it to 32 bytes. (Even though the
architecture defines 16 as the minimum D-cache line size, even the
chosen value of 32 is highly unlikely to ever be encountered on real
hardware, and this works with any line size >= 32)
* due to ARM64_WORKAROUND_CLEAN_CACHE, we actually use a DC CIVAC here
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The efi_enter_kernel() routine will be shared between the existing EFI
stub and the zboot decompressor, and the version of
dcache_clean_to_poc() that the core kernel exports to the stub will not
be available in the latter case.
So move the handling into the .c file which will remain part of the stub
build that integrates directly with the kernel proper.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
No need for the same pattern to be used four times for each architecture
individually if we can just apply it once later.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The EFI properties table was a short lived experiment that never saw the
light of day on non-x86 (if at all) so let's drop the handling of it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Randomizing the UEFI runtime memory map requires the use of the
SetVirtualAddressMap() EFI boot service, which we prefer to avoid. So
let's drop randomization, which was already problematic in combination
with hibernation, which means that distro kernels never enabled it in
the first place.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The gadget may change over bind/unbind cycles, so set it each time during
bind, not only the first time. Without it we get a use-after-free with
the following example:
cd /sys/kernel/config/usb_gadget/; mkdir -p mygadget; cd mygadget
mkdir -p configs/c.1/strings/0x409
echo "C1:Composite Device" > configs/c.1/strings/0x409/configuration
mkdir -p functions/ecm.usb0
ln -s functions/ecm.usb0 configs/c.1/
rmmod dummy_hcd
modprobe dummy_hcd
KASAN will complain shortly after the 'modprobe':
usb 2-1: New USB device found, idVendor=0000, idProduct=0000, bcdDevice= 6.01
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
==================================================================
BUG: KASAN: use-after-free in gether_connect+0xb8/0x30c
Read of size 4 at addr cbef170c by task swapper/3/0
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.1.0-rc3-00014-g41ff012f50cb-dirty #322
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from print_report+0x134/0x4d4
print_report from kasan_report+0x78/0x10c
kasan_report from gether_connect+0xb8/0x30c
gether_connect from ecm_set_alt+0x124/0x254
ecm_set_alt from composite_setup+0xb98/0x2b18
composite_setup from configfs_composite_setup+0x80/0x98
configfs_composite_setup from dummy_timer+0x8f0/0x14a0 [dummy_hcd]
...
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221104131031.850850-3-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC is not a suitable parent of the net device as the UDC can
change or vanish during the lifecycle of the ethernet gadget. This
can be illustrated with the following:
mkdir -p /sys/kernel/config/usb_gadget/mygadget
cd /sys/kernel/config/usb_gadget/mygadget
mkdir -p configs/c.1/strings/0x409
echo "C1:Composite Device" > configs/c.1/strings/0x409/configuration
mkdir -p functions/ecm.usb0
ln -s functions/ecm.usb0 configs/c.1/
echo "dummy_udc.0" > UDC
rmmod dummy_hcd
The 'rmmod' removes the UDC from the just created gadget, leaving
the still existing net device with a no longer existing parent.
Accessing the ethernet device with commands like:
ip --details link show usb0
will result in a KASAN splat:
==================================================================
BUG: KASAN: use-after-free in if_nlmsg_size+0x3e8/0x528
Read of size 4 at addr c5c84754 by task ip/357
CPU: 3 PID: 357 Comm: ip Not tainted 6.1.0-rc3-00013-gd14953726b24-dirty #324
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from print_report+0x134/0x4d4
print_report from kasan_report+0x78/0x10c
kasan_report from if_nlmsg_size+0x3e8/0x528
if_nlmsg_size from rtnl_getlink+0x2b4/0x4d0
rtnl_getlink from rtnetlink_rcv_msg+0x1f4/0x674
rtnetlink_rcv_msg from netlink_rcv_skb+0xb4/0x1f8
netlink_rcv_skb from netlink_unicast+0x294/0x478
netlink_unicast from netlink_sendmsg+0x328/0x640
netlink_sendmsg from ____sys_sendmsg+0x2a4/0x3b4
____sys_sendmsg from ___sys_sendmsg+0xc8/0x12c
___sys_sendmsg from sys_sendmsg+0xa0/0x120
sys_sendmsg from ret_fast_syscall+0x0/0x1c
Solve this by not setting the parent of the ethernet device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221104131031.850850-2-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has been replaced by the Ingenic PHY driver that uses the
generic PHY framework.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-8-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support PHYs implemented using the generic PHY framework instead of the
deprecated USB-PHY framework.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-7-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The jz4740-musb driver does not really support OTG, so it has no reason
to disable external hubs, especially since it's a system-wide setting
and we don't want external hubs to be disabled for other USB host
controllers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-6-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When musb->xceiv is not provided but musb->phy is, support setting the
OTG mode (host, peripheral) using the generic PHY framework.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-5-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb_otg_state_string() simply calls usb_otg_state_string().
This will make it easier to get rid of the musb->xceiv dependency later.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of manipulating musb->xceiv->otg->state directly, use the newly
introduced musb_get_state() and musb_set_state() inline functions.
Later, these inline functions will be modified to get rid of the
musb->xceiv dependency, which prevents the musb code from using the
generic PHY subsystem.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221026182657.146630-2-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check which mode the hardware is in, and selecte the peripheral
driver if the hardware is in explicit peripheral mode, otherwise
select host mode.
This should solve the immediate problem that both subdrivers
can get probed.
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221023144708.3596563-3-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is since ages perfectly possible to compile both of these
modules into the same kernel, which makes no sense since it
is one piece of hardware.
Compile one module named "fotg210.ko" for both HCD and UDC
drivers by collecting the init calls into a fotg210-core.c
file and start to centralize things handling one and the same
piece of hardware.
Stub out the initcalls if one or the other part of the driver
was not selected.
Tested by compiling one or the other or both of the drivers
into the kernel and as modules.
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221023144708.3596563-2-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Faraday FOTG210 is a dual-mode OTG USB controller that can
act as host, peripheral or both. To be able to probe from one
hardware description and to follow the pattern of other dual-
mode controllers such as MUSB or MTU3 we need to collect the
two, currently completely separate drivers in the same
directory.
After this, users need to select the main symbol USB_FOTG210
and then each respective subdriver. We pave the road to
compile both drivers into the same kernel and select the
one we want to use at probe() time, and possibly add OTG
support in the end.
This patch doesn't do much more than create the new symbol
and collect the drivers in one place. We also add a comment
for the section of dual-mode controllers in the Kconfig
file so people can see what these selections are about.
Also add myself as maintainer as there has been little
response on my patches to these drivers.
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221023144708.3596563-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tools/usb/aio_simple.c file when cross-compiled with
aarch64-*-gnu-gcc toolchain(s) leads to the following errors:
aio_simple.c:30:10: fatal error: endian.h: No such file or directory
30 | #include <endian.h>
| ^~~~~~~~~~
aio_simple.c:88:14: note: (near initialization for
'descriptors.fs_count')
aio_simple.c:110:14: error: initializer element is not constant
110 | .hs_count = htole32(3),
| ^~~~~~~
aio_simple.c:110:14: note: (near initialization for
'descriptors.hs_count')
aio_simple.c:124:22: error: initializer element is not constant
124 | .wMaxPacketSize = htole16(512),
| ^~~~~~~
aio_simple.c:124:22: note: (near initialization for
'descriptors.hs_descs.bulk_sink.wMaxPacketSize')
Fix these compilation issues by:
- Switching to _DEFAULT_SOURCE:
_BSD_SOURCE is deprecated and gives a build warning. Let's use
_DEFAULT_SOURCE instead.
- Currently this file uses library htole16/32 function calls.
Replace these with equivalent 'cpu_to_le16/32' calls.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20221029161312.171165-1-bhupesh.sharma@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM_SLEEP is not set, the following error will be shown up
when build kernel:
error: 'ci_handle_power_lost' defined but not used.
This will move ci_handle_power_lost() to an area wrapped by
CONFIG_PM_SLEEP.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Fixes: 74494b3321 ("usb: chipidea: core: add controller resume support when controller is powered off")
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221026121157.1491302-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add devm_usb_get_phy_by_phandle() to devres.rst. It's introduced
by commit 5d3c28b5a4 ("usb: otg: add device tree support to otg
library").
Add devm_usb_get_phy_by_node() to devres.rst. It's introduced by
commit e842b84c8e ("usb: phy: Add interface to get phy give of
device_node.")
Fixes: 5d3c28b5a4 ("usb: otg: add device tree support to otg library")
Fixes: e842b84c8e ("usb: phy: Add interface to get phy give of device_node.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221103020625.1003759-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ast_vhub_epn_handle_ack() when the received data length exceeds the
buffer, it does not check the case and just copies to req.buf and cause
a buffer overflow, kernel oops on this case.
This issue could be reproduced on a BMC with an OS that enables the
lan over USB:
1. In OS, enable the usb eth dev, verify it pings the BMC OK;
2. In OS, set the usb dev mtu to 2000. (Default is 1500);
3. In OS, ping the BMC with `-s 2000` argument.
The BMC kernel will get oops with below logs:
skbuff: skb_over_panic: text:8058e098 len:2048 put:2048 head:84c678a0 data:84c678c2 tail:0x84c680c2 end:0x84c67f00 dev:usb0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
Internal error: Oops - BUG: 0 [#1] ARM
CPU: 0 PID: 0 Comm: swapper Not tainted 5.15.69-c9fb275-dirty-d1e579a #1
Hardware name: Generic DT based system
PC is at skb_panic+0x60/0x6c
LR is at irq_work_queue+0x6c/0x94
Fix the issue by checking the length and set `-EOVERFLOW`.
Tested: Verify the BMC kernel does not get oops in the above case, and
the usb ethernet gets RX packets errors instead.
Signed-off-by: Lei YU <yulei.sh@bytedance.com>
Signed-off-by: Henry Tian <tianxiaofeng@bytedance.com>
Reviewed-by: Neal Liu <neal_liu@aspeedtech.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: https://lore.kernel.org/r/20221024094853.2877441-1-yulei.sh@bytedance.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver often takes on the order of 10ms to start, but in some cases
takes more than 100ms. It shouldn't have many cross-device dependencies
to race with, nor racy access to shared state with other drivers, so
this should be a relatively low risk change.
This driver was pinpointed as part of a survey of top slowest initcalls
(i.e., are built in, and probing synchronously) on a lab of ChromeOS
systems.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20221028184507.v2.2.I5a309231785d3a4e37118a25e84f5caa0136a343@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver often takes on the order of 8ms to start, but every little
bit counts. It shouldn't have many cross-device dependencies to
race with, nor racy access to shared state with other drivers, so this
should be a relatively low risk change.
This driver was pinpointed as part of a survey of top slowest initcalls
(i.e., are built in, and probing synchronously) on a lab of ChromeOS
systems.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20221028184507.v2.1.I9a5353f81d1509f85f3a04f0cdc9099f6fe60811@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB phy may be a system wakeup source, so add wakeup source property
to keep its resource (e.g. power domain) active to make USB remote
wakeup work.
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1666764742-4201-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
