It has been pointed out that the kernel log messages warning about
problems in USB configuration and related descriptors are vexing for
users. The warning log level has a fairly high priority, but the user
can do nothing to fix the underlying errors in the device's firmware.
To reduce the amount of useless information produced by tools that
filter high-priority log messages, we can change these warnings to
notices, i.e., change dev_warn() to dev_notice(). The same holds for
a few messages that currently use dev_err(): Unless they indicate a
failure that might make a device unusable (such as inability to
transfer a config descriptor), change them to dev_notice() also.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216630
Suggested-by: Artem S. Tashkinov <aros@gmx.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Y2KzPx0h6z1jXCuN@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocated iova ranges need to be invalidated immediately or otherwise
they might or might not work when used by master or CPU. This was
discovered when running video decoder conformity test with Cedrus. Some
videos were now and then decoded incorrectly and generated page faults.
According to vendor driver, it's enough to invalidate just start and end
TLB and PTW cache lines. Documentation says that neighbouring lines must
be invalidated too. Finally, when page fault occurs, that iova must be
invalidated the same way, according to documentation.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-6-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Function sun50i_table_flush() takes number of entries as an argument,
not number of bytes. Fix that mistake in sun50i_dte_get_page_table().
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-5-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Because driver has enum type permissions and iommu subsystem has bitmap
type, we have to be careful how check for combined read and write
permissions is done. In such case, we have to mask both permissions and
check that both are set at the same time.
Current code just masks both flags but doesn't check that both are set.
In short, it always sets R/W permission, regardles if requested
permissions were RO, WO or RW. Fix that.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-4-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
We have to reset masters for all faults - permissions, L1 fault or L2
fault. Currently it's done only for permissions. If other type of fault
happens, master is in locked up state. Fix that by really considering
all fault sources.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-3-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reset signal is asserted by writing 0 to the corresponding locations of
masters we want to reset. So in order to deassert all reset signals, we
should write 1's to all locations.
Current code writes 1's to locations of masters which were just reset
which is good. However, at the same time it also writes 0's to other
locations and thus asserts reset signals of remaining masters. Fix code
by writing all 1's when we want to deassert all reset signals.
This bug was discovered when working with Cedrus (video decoder). When
it faulted, display went blank due to reset signal assertion.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20221025165415.307591-2-jernej.skrabec@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Use sig_atomic_t for variables written/accessed in signal
handlers. This is undefined behavior as per:
https://wiki.sei.cmu.edu/confluence/display/c/SIG31-C.+Do+not+access+shared+objects+in+signal+handlers
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20221024181913.630986-9-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
While s390-iommu currently implements the map_page()/unmap_page()
operations which only map/unmap a single page at a time the internal
s390_iommu_update_trans() API already supports mapping/unmapping a range
of pages at once. Take advantage of this by implementing the
map_pages()/unmap_pages() operations instead thus allowing users of the
IOMMU drivers to map multiple pages in a single call followed by
a single I/O TLB flush if needed.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20221025115657.1666860-7-schnelle@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The .pgsize_bitmap property of struct iommu_ops is not a page mask but
rather has a bit set for each size of pages the IOMMU supports. As the
comment correctly pointed out at this moment the code only support 4K
pages so simply use SZ_4K here.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20221025115657.1666860-6-schnelle@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The domain->geometry.aperture_end specifies the last valid address treat
it as such when checking if a DMA address is valid.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20221025115657.1666860-5-schnelle@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The s390 IOMMU driver currently sets the IOMMU domain's aperture to
match the device specific DMA address range of the device that is first
attached. This is not ideal. For one if the domain has no device
attached in the meantime the aperture could be shrunk allowing
translations outside the aperture to exist in the translation tables.
Also this is a bit of a misuse of the aperture which really should
describe what addresses can be translated and not some device specific
limitations.
Instead of misusing the aperture like this we can instead create
reserved ranges for the ranges inaccessible to the attached devices
allowing devices with overlapping ranges to still share an IOMMU domain.
This also significantly simplifies s390_iommu_attach_device() allowing
us to move the aperture check to the beginning of the function and
removing the need to hold the device list's lock to check the aperture.
As we then use the same aperture for all domains and it only depends on
the table properties we can already check zdev->start_dma/end_dma at
probe time and turn the check on attach into a WARN_ON().
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20221025115657.1666860-4-schnelle@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The struct s390_domain_device serves the sole purpose as list entry for
the devices list of a struct s390_domain. As it contains no additional
information besides a list_head and a pointer to the struct zpci_dev we
can simplify things and just thread the device list through struct
zpci_dev directly. This removes the need to allocate during domain
attach and gets rid of one level of indirection during mapping
operations.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20221025115657.1666860-3-schnelle@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since commit fa7e9ecc5e ("iommu/s390: Tolerate repeat attach_dev
calls") we can end up with duplicates in the list of devices attached to
a domain. This is inefficient and confusing since only one domain can
actually be in control of the IOMMU translations for a device. Fix this
by detaching the device from the previous domain, if any, on attach.
Add a WARN_ON() in case we still have attached devices on freeing the
domain. While here remove the re-attach on failure dance as it was
determined to be unlikely to help and may confuse debug and recovery.
Fixes: fa7e9ecc5e ("iommu/s390: Tolerate repeat attach_dev calls")
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20221025115657.1666860-2-schnelle@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Variable cnt is just being incremented and it's never used
anywhere else. The variable and the increment are redundant so
remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20221024134301.2158939-1-colin.i.king@gmail.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Daniel Machon says:
====================
Add new PCP and APPTRUST attributes to dcbnl
This patch series adds new extension attributes to dcbnl, to support PCP
prioritization (and thereby hw offloadable pcp-based queue
classification) and per-selector trust and trust order. Additionally,
the microchip sparx5 driver has been dcb-enabled to make use of the new
attributes to offload PCP, DSCP and Default prio to the switch, and
implement trust order of selectors.
For pre-RFC discussion see:
https://lore.kernel.org/netdev/Yv9VO1DYAxNduw6A@DEN-LT-70577/
For RFC series see:
https://lore.kernel.org/netdev/20220915095757.2861822-1-daniel.machon@microchip.com/
In summary: there currently exist no convenient way to offload per-port
PCP-based queue classification to hardware. The DCB subsystem offers
different ways to prioritize through its APP table, but lacks an option
for PCP. Similarly, there is no way to indicate the notion of trust for
APP table selectors. This patch series addresses both topics.
PCP based queue classification:
- 8021Q standardizes the Priority Code Point table (see 6.9.3 of IEEE
Std 802.1Q-2018). This patch series makes it possible, to offload
the PCP classification to said table. The new PCP selector is not a
standard part of the APP managed object, therefore it is
encapsulated in a new non-std extension attribute.
Selector trust:
- ASIC's often has the notion of trust DSCP and trust PCP. The new
attribute makes it possible to specify a trust order of app
selectors, which drivers can then react on.
DCB-enable sparx5 driver:
- Now supports offloading of DSCP, PCP and default priority. Only one
mapping of protocol:priority is allowed. Consecutive mappings of the
same protocol to some new priority, will overwrite the previous. This
is to keep a consistent view of the app table and the hardware.
- Now supports dscp and pcp trust, by use of the introduced
dcbnl_set/getapptrust ops. Sparx5 supports trust orders: [], [dscp],
[pcp] and [dscp, pcp]. For now, only DSCP and PCP selectors are
supported by the driver, everything else is bounced.
Patch #1 introduces a new PCP selector to the APP object, which makes it
possible to encode PCP and DEI in the app triplet and offload it to the
PCP table of the ASIC.
Patch #2 Introduces the new extension attributes
DCB_ATTR_DCB_APP_TRUST_TABLE and DCB_ATTR_DCB_APP_TRUST. Trusted
selectors are passed in the nested DCB_ATTR_DCB_APP_TRUST_TABLE
attribute, and assembled into an array of selectors:
u8 selectors[256];
where lower indexes has higher precedence. In the array, selectors are
stored consecutively, starting from index zero. With a maximum number of
256 unique selectors, the list has the same maximum size.
Patch #3 Sets up the dcbnl ops hook, and adds support for offloading pcp
app entries, to the PCP table of the switch.
Patch #4 Makes use of the dcbnl_set/getapptrust ops, to set a per-port
trust order.
Patch #5 Adds support for offloading dscp app entries to the DSCP table
of the switch.
Patch #6 Adds support for offloading default prio app entries to the
switch.
====================
Link: https://lore.kernel.org/r/20221101094834.2726202-1-daniel.machon@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for offloading default prio {ETHERTYPE, 0, prio}.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support for offloading dscp app entries. Dscp values are global for
all ports on the sparx5 switch. Therefore, we replicate each dscp app
entry per-port.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make use of set/getapptrust() to implement per-selector trust and trust
order.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add new registers and functions to support offload of pcp app entries.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add new apptrust extension attributes to the 8021Qaz APP managed object.
Two new attributes, DCB_ATTR_DCB_APP_TRUST_TABLE and
DCB_ATTR_DCB_APP_TRUST, has been added. Trusted selectors are passed in
the nested attribute DCB_ATTR_DCB_APP_TRUST, in order of precedence.
The new attributes are meant to allow drivers, whose hw supports the
notion of trust, to be able to set whether a particular app selector is
trusted - and in which order.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add new PCP selector for the 8021Qaz APP managed object.
As the PCP selector is not part of the 8021Qaz standard, a new non-std
extension attribute DCB_ATTR_DCB_APP has been introduced. Also two
helper functions to translate between selector and app attribute type
has been added. The new selector has been given a value of 255, to
minimize the risk of future overlap of std- and non-std attributes.
The new DCB_ATTR_DCB_APP is sent alongside the ieee std attribute in the
app table. This means that the dcb_app struct can now both contain std-
and non-std app attributes. Currently there is no overlap between the
selector values of the two attributes.
The purpose of adding the PCP selector, is to be able to offload
PCP-based queue classification to the 8021Q Priority Code Point table,
see 6.9.3 of IEEE Std 802.1Q-2018.
PCP and DEI is encoded in the protocol field as 8*dei+pcp, so that a
mapping of PCP 2 and DEI 1 to priority 3 is encoded as {255, 10, 3}.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/2a2570a8d12c80a7d36837b6c586daa708ca09d7.1665033732.git.christophe.leroy@csgroup.eu
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Swap the 1st and 2nd arguments to be consistent with the usage of
kvcalloc().
Fixes: c9b8fecddb ("KVM: use kvcalloc for array allocations")
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Message-Id: <20221103011749.139262-1-liaochang1@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In addition to adding some fairly simple OF support code, we make some
slight adjustments to the userspace-consumer driver to properly
support use with regulator-output hardware:
- We now do an exclusive get of the supply regulators so as to
prevent regulator_init_complete_work from automatically disabling
them.
- Instead of assuming that the supply is initially disabled, we now
query its state to determine the initial value of drvdata->enabled.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20221031233704.22575-4-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
This describes a power output supplied by a regulator, such as a
power outlet on a power distribution unit (PDU).
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221031233704.22575-3-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
We had an exclusive variant of the devm_regulator_get() API, but no
corresponding variant for the bulk API; let's add one now. We add a
generalized version of the existing regulator_bulk_get() function that
additionally takes a get_type parameter and redefine
regulator_bulk_get() in terms of it, then do similarly with
devm_regulator_bulk_get(), and finally add the new
devm_regulator_bulk_get_exclusive().
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20221031233704.22575-2-zev@bewilderbeest.net
Signed-off-by: Mark Brown <broonie@kernel.org>
kvm_zap_gfn_range() must be called in an SRCU read-critical section, but
there is no SRCU annotation in __kvm_set_or_clear_apicv_inhibit(). This
can lead to the following warning via
kvm_arch_vcpu_ioctl_set_guest_debug() if a Shadow MMU is in use (TDP
MMU disabled or nesting):
[ 1416.659809] =============================
[ 1416.659810] WARNING: suspicious RCU usage
[ 1416.659839] 6.1.0-dbg-DEV #1 Tainted: G S I
[ 1416.659853] -----------------------------
[ 1416.659854] include/linux/kvm_host.h:954 suspicious rcu_dereference_check() usage!
[ 1416.659856]
...
[ 1416.659904] dump_stack_lvl+0x84/0xaa
[ 1416.659910] dump_stack+0x10/0x15
[ 1416.659913] lockdep_rcu_suspicious+0x11e/0x130
[ 1416.659919] kvm_zap_gfn_range+0x226/0x5e0
[ 1416.659926] ? kvm_make_all_cpus_request_except+0x18b/0x1e0
[ 1416.659935] __kvm_set_or_clear_apicv_inhibit+0xcc/0x100
[ 1416.659940] kvm_arch_vcpu_ioctl_set_guest_debug+0x350/0x390
[ 1416.659946] kvm_vcpu_ioctl+0x2fc/0x620
[ 1416.659955] __se_sys_ioctl+0x77/0xc0
[ 1416.659962] __x64_sys_ioctl+0x1d/0x20
[ 1416.659965] do_syscall_64+0x3d/0x80
[ 1416.659969] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Always take the KVM SRCU read lock in __kvm_set_or_clear_apicv_inhibit()
to protect the GFN to memslot translation. The SRCU read lock is not
technically required when no Shadow MMUs are in use, since the TDP MMU
walks the paging structures from the roots and does not need to look up
GFN translations in the memslots, but make the SRCU locking
unconditional for simplicty.
In most cases, the SRCU locking is taken care of in the vCPU run loop,
but when called through other ioctls (such as KVM_SET_GUEST_DEBUG)
there is no srcu_read_lock.
Tested: ran tools/testing/selftests/kvm/x86_64/debug_regs on a DBG
build. This patch causes the suspicious RCU warning to disappear.
Note that the warning is hit in __kvm_zap_rmaps(), so
kvm_memslots_have_rmaps() must return true in order for this to
repro (i.e. the TDP MMU must be off or nesting in use.)
Reported-by: Greg Thelen <gthelen@google.com>
Fixes: 36222b117e ("KVM: x86: don't disable APICv memslot when inhibited")
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20221102205359.1260980-1-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Don't populate the read-only const array uid_strings on the stack but
instead make it static. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20221103120624.72583-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During initialisation DAPM tries to read the state of the MUX
being connected, resulting in this error log:
input-mux: ASoC: error at soc_component_read_no_lock on input-mux: -5
Provide a read function which allows DAPM to read the state of the
MUX.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/20221028191303.166115-1-maarten.zanders@mind.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch the driver from legacy gpio API that is deprecated to the newer
gpiod API that respects line polarities described in ACPI/DT.
The driver still tries to support shared reset lines, by first trying to
allocate the reset GPIO normally, and then non-exclusively, although the
utility of such support is questionable, toggling reset line from one
driver/instance will result in all chips being reset, potentially at an
inopportune moment.
Note that this change depends on commit fbbbcd177a ("gpiolib: of: add
quirk for locating reset lines with legacy bindings") to translate
request for "reset" GPIO to the legacy name "gpio-reset" in case when
proper name is not used.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20221102232004.1721864-3-dmitry.torokhov@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As of 0426370b58 ("ARM: dts: omap2420-n810: Correct the audio codec
(tlv320aic33) node") the DTS properly specifies reset GPIO, and the
device name in auxdata lookup table does not even match the one in
device tree anymore, so stop instantiating it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221102232004.1721864-1-dmitry.torokhov@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Having two DMICs, a front DMIC and a Rear DMIC,
but only host audio input AUX port0 is used for these two Dmics.
A "dmic-gpios" property is used for a mixer control to switch
the dmic signal source between the Front and Rear Dmic.
Refer to this one as an example,
commit 3cfbf07c6d
("ASoC: qcom: sc7180: Modify machine driver for 2mic")
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221102125936.2176748-3-ajye_huang@compal.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Selective update area is now aligned with DSC slice height when
DSC is enabled. Remove inappropriate warning about missing DSC
alignment.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Fixes: 47d4ae2192 ("drm/i915/mtl: Extend PSR support")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7212
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102174544.2288205-3-jouni.hogander@intel.com
Do not enable psr2 if panel ganularity is not aligned with DSC slice
height when DSC is enabled
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102174544.2288205-2-jouni.hogander@intel.com
Stanislav reported a lockdep warning, which is caused by the
cancel_work_sync() called inside sock_map_close(), as analyzed
below by Jakub:
psock->work.func = sk_psock_backlog()
ACQUIRE psock->work_mutex
sk_psock_handle_skb()
skb_send_sock()
__skb_send_sock()
sendpage_unlocked()
kernel_sendpage()
sock->ops->sendpage = inet_sendpage()
sk->sk_prot->sendpage = tcp_sendpage()
ACQUIRE sk->sk_lock
tcp_sendpage_locked()
RELEASE sk->sk_lock
RELEASE psock->work_mutex
sock_map_close()
ACQUIRE sk->sk_lock
sk_psock_stop()
sk_psock_clear_state(psock, SK_PSOCK_TX_ENABLED)
cancel_work_sync()
__cancel_work_timer()
__flush_work()
// wait for psock->work to finish
RELEASE sk->sk_lock
We can move the cancel_work_sync() out of the sock lock protection,
but still before saved_close() was called.
Fixes: 799aa7f98d ("skmsg: Avoid lock_sock() in sk_psock_backlog()")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20221102043417.279409-1-xiyou.wangcong@gmail.com
With recent sync of linux/in.h tools/include headers are now relying on
__DECLARE_FLEX_ARRAY macro, which isn't itself defined inside
tools/include headers anywhere and is instead assumed to be present in
system-wide UAPI header. This breaks isolated environments that don't
have kernel UAPI headers installed system-wide, like BPF CI ([0]).
To fix this, bring in include/uapi/linux/stddef.h into tools/include.
We can't just copy/paste it, though, it has to be processed with
scripts/headers_install.sh, which has a dependency on scripts/unifdef.
So the full command to (re-)generate stddef.h for inclusion into
tools/include directory is:
$ make scripts_unifdef && \
cp $KBUILD_OUTPUT/scripts/unifdef scripts/ && \
scripts/headers_install.sh include/uapi/linux/stddef.h tools/include/uapi/linux/stddef.h
This assumes KBUILD_OUTPUT envvar is set and used for out-of-tree builds.
[0] https://github.com/kernel-patches/bpf/actions/runs/3379432493/jobs/5610982609
Fixes: 036b8f5b89 ("tools headers uapi: Update linux/in.h copy")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: https://lore.kernel.org/bpf/20221102182517.2675301-2-andrii@kernel.org
