MCAN nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-9-afd@ti.com
MDIO nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.
As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the MDIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-8-afd@ti.com
Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).
Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-7-afd@ti.com
ECAP nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-6-afd@ti.com
EPWM nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-5-afd@ti.com
SPI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-4-afd@ti.com
I2C nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-3-afd@ti.com
UART nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-2-afd@ti.com
The GPMC node defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless it is extended with pinmux information.
As the pinmux is only known at the board integration level, this node
should only be enabled when provided with this information.
Disable the GPMC node in the dtsi file. Since the ELM is made to work
with the GPMC, disable it too.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-11-afd@ti.com
MCAN nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-10-afd@ti.com
MDIO nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.
As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the MDIO nodes (in both CPSW and ICSSG) in the dtsi files and
only enable the ones that are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-9-afd@ti.com
Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).
Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-8-afd@ti.com
PCIe nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerDes PHY.
And usually only one of the two modes can be used at a time as they
share a SerDes link.
As the PHY and mode is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the PCIe nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-7-afd@ti.com
ECAP nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-6-afd@ti.com
EPWM nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-5-afd@ti.com
SPI nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-4-afd@ti.com
I2C nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-3-afd@ti.com
UART nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.
As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.
Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-2-afd@ti.com
This Asus Zenbook laptop use Realtek HDA codec combined with
2xCS35L41 Amplifiers using I2C with Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221028102742.2588687-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for the new SC8280XP binding.
Note that the binding does not try to describe every register subregion
and instead the driver holds the corresponding offsets.
Also note that the driver will continue to accept the old binding, at
least for the time being.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-11-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for supporting devicetree bindings which do not use a
child node, move the PHY creation to probe() proper and parse the serdes
resource in what is now the legacy devicetree helper.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-10-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current QMP UFS PHY bindings are based on the original MSM8996 PCIe
PHY binding which provided multiple PHYs per IP block and these in turn
were described by child nodes.
The QMP UFS PHY block only provide a single PHY and the remnant child
node does not really reflect the hardware.
The original MSM8996 binding also ended up describing the individual
register blocks as belonging to either the wrapper node or the PHY child
nodes.
This is an unnecessary level of detail which has lead to problems when
later IP blocks using different register layouts have been forced to fit
the original mould rather than updating the binding. The bindings are
arguable also incomplete as they only the describe register blocks used
by the current Linux drivers.
Add a new binding for the UFS QMP PHYs found on SC8280XP which further
bindings can be based on.
Note that the current binding is simply removed instead of being
deprecated as it was only recently merged and support for SC8280XP is
still under development.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-9-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current QMP UFS PHY bindings are based on the original MSM8996 PCIe
PHY binding which provided multiple PHYs per IP block and these in turn
were described by child nodes.
The QMP UFS PHY block only provide a single PHY and the remnant child
node does not really reflect the hardware.
The original MSM8996 binding also ended up describing the individual
register blocks as belonging to either the wrapper node or the PHY child
nodes.
This is an unnecessary level of detail which has lead to problems when
later IP blocks using different register layouts have been forced to fit
the original mould rather than updating the binding. The bindings are
arguable also incomplete as they only the describe register blocks used
by the current Linux drivers.
In preparation for adding new bindings for SC8280XP which further
bindings can be based on, rename the current bindings after MSM8996 and
add a reference to the SC8280XP bindings.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-8-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clean up the PHY initialisation somewhat programming both tx and rx for
the second lane after the first lane.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-7-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rename the PHY operation structure so that it has a "phy_ops" suffix and
move it next to the implementation.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-6-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stop abusing the driver data pointer and instead pass the driver state
structure directly to the initialisation helpers during probe.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-5-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since the QMP driver split there will be at most a single child node so
drop the obsolete iteration construct.
While at it, drop the verbose error logging that would have been
printed also on probe deferrals.
Note that there's no need to check if there are additional child nodes
(the kernel is not a devicetree validator), but let's return an error if
there are no child nodes at all for now.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-4-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The UFS QMP PHY driver only manages a single PHY so merge the old
qcom_qmp and qmp_phy structures and drop the PHY array.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move the device-id table below probe() and next to the driver structure
to keep the driver callback functions grouped together.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221024090041.19574-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit fc64623637 ("phy: qcom-qmp-combo,usb: add support for separate
PCS_USB region") started treating the PCS_USB registers as potentially
separate from the PCS registers but used the wrong base when no PCS_USB
offset has been provided.
Fix the PCS_USB base used at runtime resume to prevent dereferencing a
NULL pointer on platforms that do not provide a PCS_USB offset (e.g.
SC7180).
Fixes: fc64623637 ("phy: qcom-qmp-combo,usb: add support for separate PCS_USB region")
Cc: stable@vger.kernel.org # 5.20
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20221026162116.26462-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the Arm PL354 static memory controller to the existing
Arm PL353 binding. Both are different configurations of the same IP with
support for different types of memory interfaces.
The 'arm,pl354' binding has already been in use upstream for a long time
in Arm development boards. The existing users have only the controller
without any child devices, so drop the required address properties
(ranges, #address-cells, #size-cells). The schema for 'ranges' is too
constrained as the order is not important and the PL354 has 8
chipselects (And the PL353 actually has up to 8 too).
The clocks aren't really correct in either case. There's 1 bus clock and
then a clock for each of the 2 memory interfaces.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221021203928.286169-1-robh@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
renesas.yaml lists out all the Renesas SoC's and the platforms/EVK's which
is either ARM32/ARM64. It would rather make sense if we move renesas.yaml
to the soc/renesas folder instead. This is in preparation for adding a new
SoC (RZ/Five) from Renesas which is based on RISC-V.
While at it drop the old entry for renesas.yaml from MAINTAINERS file and
there is no need to update the new file path of renesas.yaml as we already
have an entry for Documentation/devicetree/bindings/soc/renesas/ folder.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220920184904.90495-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the kernel 4.4 sources from NHSS.QSDK.9.0.2 and according
to hardware docs, the PHY registers layout used for IPQ8074 USB3 PHY is
incorrect. This platform uses offset 0x174 for the PCS_STATUS register,
0xd8 for PCS_AUTONOMOUS_MODE_CTRL, etc.
Correct the PHY registers layout.
Fixes: 94a407cc17 ("phy: qcom-qmp: create copies of QMP PHY driver")
Fixes: 507156f5a9 ("phy: qcom-qmp: Add USB QMP PHY support for IPQ8074")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Kathiravan T<quic_kathirav@quicinc.com>
Link: https://lore.kernel.org/r/20220929190017.529207-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are cases where not all CPG_MOD clocks should be assumed to support
PM. For example on the CRU block there is a particular sequence that needs
to be followed to initialize the CSI-2 D-PHY in which individual clocks
need to be turned ON/OFF, due to which Runtime PM support wasn't used by
the CRU CSI-2 driver.
This patch adds support to allow indicating if PM is not supported by the
CPG_MOD clocks. Two new members no_pm_mod_clks and num_no_pm_mod_clks are
added to struct rzg2l_cpg_info so that MOD clocks which do not support PM
can be passed by no_pm_mod_clks[] array and when the driver uses Runtime
PM support the clk ID is matched against the no_pm_mod_clks[] array to see
if the clk is needed to be included as part of Runtime PM.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221026014227.162121-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Do not automatically select the GPIOLIB and PINCTRL config options as
they are already automatically selected as part of the SOC_RENESAS
config option in drivers/soc/renesas/Kconfig.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221027112459.77413-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Do not automatically select the GPIOLIB and PINCTRL config options as
they are already automatically selected as part of the SOC_RENESAS
config option in drivers/soc/renesas/Kconfig.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20221027112300.77184-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Drop the start and pwrdn-ctrl abstractions which are no longer needed
since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-20-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the start and pwrdn-ctrl abstractions which are no longer needed
since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-19-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the start and pwrdn-ctrl abstractions which are no longer needed
since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-18-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver expects every configuration to set the pwrdn_ctrl and
phy_status masks. Add some probe WARN_ON_ONCE() to probe to catch any
new driver support that fails to provide them.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-17-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All PCIe PHYs need to start and stop the SerDes and PCS so drop the
start-ctrl abstraction which is no longer needed since the QMP driver
split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-16-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All USB PHYs need to start and stop the SerDes and PCS so drop the
start-ctrl abstraction which is no longer needed since the QMP driver
split.
Similarly, drop the pwrdn-ctrl abstraction which also is not needed
since the split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-15-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It typically takes between one and two milliseconds for the PHY to
become ready after starting it. Increase the tight 3--10 us polling
period to the more reasonable 51--200 us.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012085002.24099-14-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clean up the PHY status polling by dropping the configuration mask which
is no longer needed since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-13-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It typically takes between one and two milliseconds for the PHY to
become ready after starting it. Increase the tight 3--10 us polling
period to the more reasonable 51--200 us.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20221012085002.24099-12-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clean up the PHY ready polling by dropping the mask variables which are
no longer needed since the QMP driver split.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-11-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop the unused phy-status configuration mask which has never been used
for UFS PHYs.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221012085002.24099-10-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
