Partially revert 34918cd7. struct mgmt_key_info needs to have the same
size as its version exported to userspace.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
There's no need for the API to modify it and having it const makes it
easier to use with random strings the board code has.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With this flag codec drivers can indicate that it is desired
to ignore the pmdown_time for DAPM shutdown sequence when
playback stream is stopped.
The DAPM sequence will be executed without delay in this case.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reuse the already existing struct nl80211_sta_flag_update to specify
both, a flag mask and the flag set itself. This means
nl80211_sta_flag_update is now used for setting station flags and also
for getting station flags.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 already filled in the MCS rate info for rx'ed frames but tx'ed
frames that are sent to a monitor interface during the status callback
lack this information.
Add the radiotap fields for MCS info to ieee80211_tx_status_rtap_hdr
and populate them when sending tx'ed frames to the monitors.
The needed headroom is only extended by one byte since we don't include
legacy rate information in the rtap header for HT frames.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we introduced hci_init_sysfs() we should also rename
hci_register_sysfs() and hci_unregister_sysfs() to hci_add_sysfs() and
hci_del_sysfs() like we do with hci_conn_add/del_sysfs(). It looks more
consistent now.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We must not call device_del() if we didn't use device_add(). See module.c
for comments on that. Therefore, we need to call device_initialize() when
allocating the hci device and later device_add() instead of
device_register().
This also fixes a bug when hci_register_dev() failed and we call
hci_free_dev() without a valid core device. hci_free_dev() segfaults while
calling put_device() on invalid memory.
We already do this with hci_conn connections (hci_conn_init_sysfs()) so
they do not need to be fixed.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This was triggered by turning off encryption on ACL link when rfcomm
was using high security. rfcomm_security_cfm (which is called from rx
task) was closing DLC and this involves sending disconnect message
(and locking socket).
Move closing DLC to rfcomm_process_dlcs and only flag DLC for closure
in rfcomm_security_cfm.
BUG: sleeping function called from invalid context at net/core/sock.c:2032
in_atomic(): 1, irqs_disabled(): 0, pid: 1788, name: kworker/0:3
[<c0068a08>] (unwind_backtrace+0x0/0x108) from [<c05e25dc>] (dump_stack+0x20/0x24)
[<c05e25dc>] (dump_stack+0x20/0x24) from [<c0087ba8>] (__might_sleep+0x110/0x12c)
[<c0087ba8>] (__might_sleep+0x110/0x12c) from [<c04801d8>] (lock_sock_nested+0x2c/0x64)
[<c04801d8>] (lock_sock_nested+0x2c/0x64) from [<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc)
[<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc) from [<c047cf6c>] (sock_sendmsg+0xb0/0xd0)
[<c047cf6c>] (sock_sendmsg+0xb0/0xd0) from [<c047cfc8>] (kernel_sendmsg+0x3c/0x44)
[<c047cfc8>] (kernel_sendmsg+0x3c/0x44) from [<c056b0e8>] (rfcomm_send_frame+0x50/0x58)
[<c056b0e8>] (rfcomm_send_frame+0x50/0x58) from [<c056b168>] (rfcomm_send_disc+0x78/0x80)
[<c056b168>] (rfcomm_send_disc+0x78/0x80) from [<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc)
[<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc) from [<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0)
[<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0) from [<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84)
[<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84) from [<c0550380>] (hci_rx_task+0x1d0/0x2d0)
[<c0550380>] (hci_rx_task+0x1d0/0x2d0) from [<c009ee04>] (tasklet_action+0x138/0x1e4)
[<c009ee04>] (tasklet_action+0x138/0x1e4) from [<c009f21c>] (__do_softirq+0xcc/0x274)
[<c009f21c>] (__do_softirq+0xcc/0x274) from [<c009f6c0>] (do_softirq+0x60/0x6c)
[<c009f6c0>] (do_softirq+0x60/0x6c) from [<c009f794>] (local_bh_enable_ip+0xc8/0xd4)
[<c009f794>] (local_bh_enable_ip+0xc8/0xd4) from [<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c)
[<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c) from [<c040d470>] (data_from_chip+0xf4/0xaec)
[<c040d470>] (data_from_chip+0xf4/0xaec) from [<c04136c0>] (send_skb_to_core+0x40/0x178)
[<c04136c0>] (send_skb_to_core+0x40/0x178) from [<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0)
[<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0) from [<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0)
[<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0) from [<c02cbd9c>] (flush_to_ldisc+0x188/0x198)
[<c02cbd9c>] (flush_to_ldisc+0x188/0x198) from [<c00b2774>] (process_one_work+0x144/0x4b8)
[<c00b2774>] (process_one_work+0x144/0x4b8) from [<c00b2e8c>] (worker_thread+0x198/0x468)
[<c00b2e8c>] (worker_thread+0x198/0x468) from [<c00b9bc8>] (kthread+0x98/0xa0)
[<c00b9bc8>] (kthread+0x98/0xa0) from [<c0061744>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Current ore_check_io API receives a residual
pointer, to report partial IO. But it is actually
not used, because in a multiple devices IO there
is never a linearity in the IO failure.
On the other hand if every failing device is reported
through a received callback measures can be taken to
handle only failed devices. One at a time.
This will also be needed by the objects-layout-driver
for it's error reporting facility.
Exofs is not currently using the new information and
keeps the old behaviour of failing the complete IO in
case of an error. (No partial completion)
TODO: Use an ore_check_io callback to set_page_error only
the failing pages. And re-dirty write pages.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
All users of the ore will need to check if current code
supports the given layout. For example RAID5/6 is not
currently supported.
So move all the checks from exofs/super.c to a new
ore_verify_layout() to be used by ore users.
Note that any new layout should be passed through the
ore_verify_layout() because the ore engine will prepare
and verify some internal members of ore_layout, and
assumes it's called.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Users like the objlayout-driver would like to only pass
a partial device table that covers the IO in question.
For example exofs divides the file into raid-group-sized
chunks and only serves group_width number of devices at
a time.
The partiality is communicated by setting
ore_componets->first_dev and the array covers all logical
devices from oc->first_dev upto (oc->first_dev + oc->numdevs)
The ore_comp_dev() API receives a logical device index
and returns the actual present device in the table.
An out-of-range dev_index will BUG.
Logical device index is the theoretical device index as if
all the devices of a file are present. .i.e:
total_devs = group_width * mirror_p1 * group_count
0 <= dev_index < total_devs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Now that each ore_io_state covers only a single raid group.
A single striping_info math is needed. Embed one inside
ore_io_state to cache the calculation results and eliminate
an extra call.
Also the outer _prepare_for_striping is removed since it does nothing.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Devices supporting Process Address Space Identifiers
(PASIDs) can use an IOMMU to access multiple IO address
spaces at the same time. A PCIe device indicates support for
this feature by implementing the PASID capability. This
patch adds support for the capability to the Linux kernel.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implement the necessary functions to handle PRI capabilities
on PCIe devices. With PRI devices behind an IOMMU can signal
page fault conditions to software and recover from such
faults.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ATS does not depend on IOV support, so move the code into
its own file. This file will also include support for the
PRI and PASID capabilities later.
Also give ATS its own Kconfig variable to allow selecting it
without IOV support.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I originally submitted a patch to workaround this by pushing all Ejection
Requests and Device Checks onto the kacpi_hotplug queue.
http://marc.info/?l=linux-acpi&m=131678270930105&w=2
The patch is still insufficient in that Bus Checks also need to be added.
Rather than add all events, including non-PCI-hotplug events, to the
hotplug queue, mjg suggested that a better approach would be to modify
the acpiphp driver so only acpiphp events would be added to the
kacpi_hotplug queue.
It's a longer patch, but at least we maintain the benefit of having separate
queues in ACPI. This, of course, is still only a workaround the problem.
As Bjorn and mjg pointed out, we have to refactor a lot of this code to do
the right thing but at this point it is a better to have this code working.
The acpi core places all events on the kacpi_notify queue. When the acpiphp
driver is loaded and a PCI card with a PCI-to-PCI bridge is removed the
following call sequence occurs:
cleanup_p2p_bridge()
-> cleanup_bridge()
-> acpi_remove_notify_handler()
-> acpi_os_wait_events_complete()
-> flush_workqueue(kacpi_notify_wq)
which is the queue we are currently executing on and the process will hang.
Move all hotplug acpiphp events onto the kacpi_hotplug workqueue. In
handle_hotplug_event_bridge() and handle_hotplug_event_func() we can simply
push the rest of the work onto the kacpi_hotplug queue and then avoid the
deadlock.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: mjg@redhat.com
Cc: bhelgaas@google.com
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The land of PCI power management is a land of sorrow and ugliness,
especially in the area of signaling events by devices. There are
devices that set their PME Status bits, but don't really bother
to send a PME message or assert PME#. There are hardware vendors
who don't connect PME# lines to the system core logic (they know
who they are). There are PCI Express Root Ports that don't bother
to trigger interrupts when they receive PME messages from the devices
below. There are ACPI BIOSes that forget to provide _PRW methods for
devices capable of signaling wakeup. Finally, there are BIOSes that
do provide _PRW methods for such devices, but then don't bother to
call Notify() for those devices from the corresponding _Lxx/_Exx
GPE-handling methods. In all of these cases the kernel doesn't have
a chance to receive a proper notification that it should wake up a
device, so devices stay in low-power states forever. Worse yet, in
some cases they continuously send PME Messages that are silently
ignored, because the kernel simply doesn't know that it should clear
the device's PME Status bit.
This problem was first observed for "parallel" (non-Express) PCI
devices on add-on cards and Matthew Garrett addressed it by adding
code that polls PME Status bits of such devices, if they are enabled
to signal PME, to the kernel. Recently, however, it has turned out
that PCI Express devices are also affected by this issue and that it
is not limited to add-on devices, so it seems necessary to extend
the PME polling to all PCI devices, including PCI Express and planar
ones. Still, it would be wasteful to poll the PME Status bits of
devices that are known to receive proper PME notifications, so make
the kernel (1) poll the PME Status bits of all PCI and PCIe devices
enabled to signal PME and (2) disable the PME Status polling for
devices for which correct PME notifications are received.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "powernv" platform of the powerpc architecture needs to assign PCI
resources using a specific algorithm to fit some HW constraints of
the IBM "IODA" architecture (related to the ability to create error
handling domains that encompass specific segments of MMIO space).
For doing so, it wants to call pci_setup_bridge() from architecture
specific resource management in order to configure bridges after all
resources have been assigned. So make it non-static.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These will be shared between the sfc driver and a PCI quirk.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This adds the new API header and helper files.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Old default behaviour was "pass-on",
which is not useful in production at all.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Up to now it only operated on minor numbers. Now it can work also
on named connections.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Use a new on-disk transaction format for the activity log, which allows
for multiple changes to the active set per transaction.
Using 4k transaction blocks, we can now get rid of the work-around code
to deal with devices not supporting 512 byte logical block size.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Allow multiple changes to the active set of elements in lru_cache.
The only current user of lru_cache, drbd, is driving this generalisation.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Some open-coded clear_bit(); smp_mb__after_clear_bit();
should in fact have been smp_mb__before_clear_bit(); clear_bit();
Instead, use clear_bit_unlock() to annotate the intention,
and have it do the right thing.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Implementation of Read Local AMP Info Command
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Define Extended Flow Specification structures and default values.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
skb truesize currently accounts for sk_buff struct and part of skb head.
kmalloc() roundings are also ignored.
Considering that skb_shared_info is larger than sk_buff, its time to
take it into account for better memory accounting.
This patch introduces SKB_TRUESIZE(X) macro to centralize various
assumptions into a single place.
At skb alloc phase, we put skb_shared_info struct at the exact end of
skb head, to allow a better use of memory (lowering number of
reallocations), since kmalloc() gives us power-of-two memory blocks.
Unless SLUB/SLUB debug is active, both skb->head and skb_shared_info are
aligned to cache lines, as before.
Note: This patch might trigger performance regressions because of
misconfigured protocol stacks, hitting per socket or global memory
limits that were previously not reached. But its a necessary step for a
more accurate memory accounting.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andi Kleen <ak@linux.intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds definitins for L2CAP header sizes to be uses when calculating
payload size instead of magic numbers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Handle POLL (P) bit in L2CAP ERTM using information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Handle final (F) bit in L2CAP using information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Check frame function uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
L2CAP ERTM txseq calculation uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
reqseq calculation uses now information about control field type.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Segmentation and Reassembly (SAR) occupies different windows in standard and
extended control fields. Convert hardcoded masks to relative ones and use shift
to access SAR bits.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Supervisory bits occupy different windows in standard / extended control
fields. Convert hardcoded masks to relative ones and use shift to access
S-bit window.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Adds extended control field bit masks and rearrange defines to logical
groups: masks, flags and shift groups.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Adds support for extended window size (EWS) config option. We enable EWS
feature in L2CAP Info RSP when hs enabled. EWS option is included in L2CAP
Config Req if tx_win (which is set via socket) bigger then standard default
value (63) && hs enabled && remote side supports EWS feature.
Using EWS selects extended control field in L2CAP.
Code partly based on Qualcomm and Atheros patches sent upstream a year ago.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add empty of_device_is_compatible() and of_parse_phandle() for non-dt
builds to work.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch do the following things:
1. Add header and Copyright for marvell usb driver.
2. Add mv_usb.h in include/linux/platform_data, make the driver
fits all the marvell platform using the same ChipIdea usb ip.
3. Some SOC may has mutiple clock sources, so let me define it
in mv_usb_platform_data and give two helper functions named
udc_clock_enable/udc_clock_disable to deal with the clocks.
4. Different SOCs will have some difference in PHY initialization,
so we will remove file mv_udc_phy.c and add two funtions in
mv_usb_platform_data, let the platform relative driver to realize it.
5. Rewrite probe function according to the modification list above. Find
it will kernel panic when probe failed. The root cause is as follows:
When probe failed, the error handle may call device_unregister()
which in return will call gadget_release.In current code,
gadget_release have two issues:
1: the_controller is a NULL pointer.
2: if we free udc here, then the following code in probe
will access NULL pointer.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
some renesas_usbhs device is supporting OTG external device interface.
In that device, it is necessary to control PWEN/EXTLP on DVSTCTR.
This patch support it.
But renesas_usbhs driver doesn't have OTG support for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch add DVSTCTR control function for HOST support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs will have register DVSTCTR control function for HOST support.
This patch changes usbhsc_bus_ctrl() to usbsc_set_buswait(),
to remove DVSTCTR access from it,
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
SH7757 has a USB function with internal DMA controller (SUDMAC).
This patch supports the SUDMAC. The SUDMAC is incompatible with
general-purpose DMAC. So, it doesn't use dmaengine.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow processes that share the same XRC domain to open an existing
shareable QP. This permits those processes to receive events on the
shared QP and transfer ownership, so that any process may modify the
QP. The latter allows the creating process to exit, while a remaining
process can still transition it for path migration purposes.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
