Commit graph

355,538 commits

Author SHA1 Message Date
Ilan Tayari
899a59d301 net/mlx5e: IPSec, Add Innova IPSec offload RX data path
In RX data path, the hardware prepends a special metadata ethertype
which indicates that the packet underwent decryption, and the result of
the authentication check.

Communicate this to the stack in skb->sp.

Make wqe_size large enough to account for the injected metadata.

Support only Linked-list RQ type.

IPSec offload RX packets may have useful CHECKSUM_COMPLETE information,
which the stack may not be able to use yet.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
547eede070 net/mlx5e: IPSec, Innova IPSec offload infrastructure
Add Innova IPSec ESP crypto offload configuration paths.
Detect Innova IPSec device and set the NETIF_F_HW_ESP flag.
Configure Security Associations using the API introduced in a previous
patch.

Add Software-parser hardware descriptor layout
Software-Parser (swp) is a hardware feature in ConnectX which allows the
host software to specify protocol header offsets in the TX path, thus
overriding the hardware parser.
This is useful for protocols that the ASIC may not be able to parse on
its own.

Note that due to inline metadata, XDP is not supported in Innova IPSec.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
bebb23e6cb net/mlx5: Accel, Add IPSec acceleration interface
Add routines for manipulating the hardware IPSec SA database (SADB).

In Innova IPSec, a Security Association (SA) is added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.

Add implementation for Innova IPSec (FPGA-based) hardware.

These routines will be used by the IPSec offload support in a later patch
However they may also be used by others such as RDMA and RoCE IPSec.

mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.

In this patchset we add Innova IPSec support and mlx5/accel delegates
IPSec offloads to Innova routines.

In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
a9956d35d1 net/mlx5: FPGA, Add SBU infrastructure
Add interface to initialize and interact with Innova FPGA SBU
connections.
A client driver may use these functions to set up a high-speed DMA
connection with its SBU hardware logic, and send/receive messages
over this connection.

A later patch in this patchset will make use of these functions for
Innova IPSec offload in mlx5 Ethernet driver.

Add commands to retrieve Innova FPGA SBU capabilities, and to
read/write Innova FPGA configuration space registers and memory,
over internal I2C.

At high level, the FPGA configuration space is divided such:
 0x00000000 - 0x007fffff is reserved for the SBU
 0x00800000 - 0xffffffff is reserved for the Shell
0x400000000 - ...        is DDR memory

A later patchset will add support for accessing FPGA CrSpace and memory
over a high-speed connection. This is the reason for the ACCESS_TYPE
enumeration, which currently only supports I2C.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
c43051d72a net/mlx5: FPGA, Add SBU bypass and reset flows
The Innova FPGA includes shell hardware and Sandbox-Unit (SBU) hardware.
The shell hardware is handled by mlx5_core itself, while the SBU is
handled by a client driver.

Reset the SBU to a well-known initial state when initializing a new
device, and set the FPGA to bypass mode when uninitializing a device.
This allows the client driver to assume that its device has been
reset when a new device is detected.

During SBU reset, the FPGA is put into SBU-bypass mode. In this mode
packets do not pass through the SBU, so it cannot affect the network
data stream at all.

A factory-image does not have an SBU, so skip these flows.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
537a505741 net/mlx5: FPGA, Add high-speed connection routines
An FPGA high-speed connection has two endpoints, an FPGA QP and a
ConnectX QP.
Add library routines to create and connect the endpoints of an
FPGA high-speed connection.

These routines allow creating and interacting with both types of
connections: Shell and Sandbox Unit (SBU).

Shell connection provides an interface to the FPGA's address space,
which includes the configuration space and the DDR.
Use of the shell connection will be introduced in a later patchset.

SBU connection provides a command and/or data interface to the
application-specific logic within the FPGA.
Use of the SBU connection will be introduced in a later patch in
this patchset.

Some struct definitions are added to a new header file sdk.h, which
will be extended in later patches in the patchset.
This header file will contain the in-kernel FPGA client driver API.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
6062118d5c net/mlx5: FPGA, Add FW commands for FPGA QPs
The FPGA QP is a high-bandwidth communication channel between the host
CPU and the FPGA device. It allows performing DMA operations between
host memory and the FPGA logic via the ConnectX chip.

Add ConnectX FW commands which create and manipulate FPGA QPs.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
9410733c44 net/mlx5: FPGA, Move FPGA init/cleanup to init_once
The FPGA init and cleanup routines should be called just once per
device.
Move them to the init_once and cleanup_once routines.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
3f2b7edd7c net/mlx5: Add QP WQ support
A QP in ConnectX is a concatenation of RQ and SQ which share a QP-number
and work together.
Add support for allocating and managing the work-queue buffer for a QP, in
a similar way to how SQs and RQs are already supported.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
4b67379376 net/mlx5: Make get_cqe routine not ethernet-specific
Move mlx5e_get_cqe routine to wq.h and rename it to
mlx5_cqwq_get_cqe.

This allows it to be used by other CQ users outside of the
ethernet driver code.

A later patch in this patchset will make use of it from
FPGA code for the FPGA high-speed connection.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
095b0927f0 IB/mlx5: Respect mlx5_core reserved GIDs
Reserved gids are taken by the mlx5_core, report smaller GID table
size to IB core.

Set mlx5_query_roce_port's return value back to int. In case of
error, return an indication. This rolls back some of the change
in commit 50f22fd8ec ("IB/mlx5: Set mlx5_query_roce_port's return value to void")

Change set_roce_addr to use gid_set function, instead of directly
sending the command.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
a6f7d2aff6 net/mlx5: Add support for multiple RoCE enable
Previously, only mlx5_ib enabled RoCE on the port, but FPGA needs it as
well.
Add support for counting number of enables, so that FPGA and IB can work
in parallel and independently.
Program the HW to enable RoCE on the first enable call, and program to
disable RoCE on the last disable call.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
52ec462eca net/mlx5: Add reserved-gids support
Reserved GIDs are entries in the GID table in use by the mlx5_core
and its submodules (e.g. FPGA, SRIOV, E-Swtich, netdev).
The entries are reserved at the high indexes of the GID table.

A mlx5 submodule may reserve a certain amount of GIDs for its own use
during the load sequence by calling mlx5_core_reserve_gids, and must
also take care to un-reserve these GIDs when it closes.
Reservation is only allowed during the load sequence and before any
interfaces (e.g. mlx5_ib or mlx5_en) are up.

After reservation, a submodule may call mlx5_core_reserved_gid_alloc/
free to allocate entries from the reserved GIDs pool.

Reserve a GID table entry for every supported FPGA QP.

A later patch in the patchset will remove them from being reported to
IB core.
Another such patch will make use of these for FPGA QPs in Innova NIC.

Added lib/mlx5.h to serve as a library for mlx5 submodlues, and to
expose only public mlx5 API, more mlx5 library files will be added in
future submissions.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Ilan Tayari
9ade8c7c3c net/mlx5: Set interface flags before cleanup in unload_one
In load_one, the interface flags are changed from down to up,
only after initializing the interfaces.
In unload_one, the flags are changed from up to down before the
interface cleanup.

Change the cleanup order to be opposite to initialization order.

This fixes flag consistency between init and cleanup.

Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2017-06-27 16:36:47 +03:00
Colin Ian King
593814d1be net/mlx4: fix spelling mistake: "coalesing" -> "coalescing"
Trivial fix to spelling mistake in en_dbg debug message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-26 23:18:29 -04:00
Matthias Schiffer
17dd0ec470 net: add netlink_ext_ack argument to rtnl_link_ops.slave_changelink
Add support for extended error reporting.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-26 23:13:22 -04:00
Matthias Schiffer
a8b8a889e3 net: add netlink_ext_ack argument to rtnl_link_ops.validate
Add support for extended error reporting.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-26 23:13:22 -04:00
Matthias Schiffer
ad744b223c net: add netlink_ext_ack argument to rtnl_link_ops.changelink
Add support for extended error reporting.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-26 23:13:22 -04:00
Matthias Schiffer
7a3f4a1851 net: add netlink_ext_ack argument to rtnl_link_ops.newlink
Add support for extended error reporting.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-26 23:13:21 -04:00
Michael Grzeschik
dacdbb4dfc net: macb: add fixed-link node support
In case the MACB is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 15:21:43 -04:00
David S. Miller
24a72b77f3 wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
 nothing really special standing out.
 
 What makes me happy that we have now more vendors actively
 contributing to upstream drivers. In this pull request we have patches
 from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
 still have patches from Marvell and Quantenna pending in patchwork. Now
 that's something comparing to how things looked 11 years ago in Jeff
 Garzik's "State of the Union: Wireless" email:
 
 https://lkml.org/lkml/2006/1/5/671
 
 Major changes:
 
 wil6210
 
 * add low level RF sector interface via nl80211 vendor commands
 
 * add module parameter ftm_mode to load separate firmware for factory
   testing
 
 * support devices with different PCIe bar size
 
 * add support for PCIe D3hot in system suspend
 
 * remove ioctl interface which should not be in a wireless driver
 
 ath10k
 
 * go back to using dma_alloc_coherent() for firmware scratch memory
 
 * add per chain RSSI reporting
 
 brcmfmac
 
 * add support multi-scheduled scan
 
 * add scheduled scan support for specified BSSIDs
 
 * add support for brcm43430 revision 0
 
 wlcore
 
 * add wil1285 compatible
 
 rsi
 
 * add RS9113 USB support
 
 iwlwifi
 
 * FW API documentation improvements (for tools and htmldoc)
 
 * continuing work for the new A000 family
 
 * bump the maximum supported FW API to 31
 
 * improve the differentiation between 8000, 9000 and A000 families
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJZT/ROAAoJEG4XJFUm622b/IwH+wQtBXP+P57DZ97BdETcZ3Wd
 ejm9KKT3IxcP7kzItT9UR1zv7LNx4NgSkJMfhf37jJ1WIuE2fp/ctNv6mz3PvohW
 jD1fLynwEMMC7PLHEy5+xGtL61KYc2mtXs/bfLFl94hZUiaocrsBDIT4fXoyIWif
 y3MUlBKDbHA27ULRd485C0MRekRSvR/rq6iST4KsIsa8RflJbdH64teTEnQPp4kh
 nvhfnaxVEqHK7mYbarC58yYLNOU8gfQXmeeTfd6jhCXRjfEw37IvtNC8BT4B9ZDX
 YMZLbkeDSwNGXIH7EIrpGOYHCPh+qsiJ+sx7YodomcJvd1nVrmbuZZt9/EqWXuY=
 =Fd/c
 -----END PGP SIGNATURE-----

Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.13

New features and bug fixes to quite a few different drivers, but
nothing really special standing out.

What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:

https://lkml.org/lkml/2006/1/5/671

Major changes:

wil6210

* add low level RF sector interface via nl80211 vendor commands

* add module parameter ftm_mode to load separate firmware for factory
  testing

* support devices with different PCIe bar size

* add support for PCIe D3hot in system suspend

* remove ioctl interface which should not be in a wireless driver

ath10k

* go back to using dma_alloc_coherent() for firmware scratch memory

* add per chain RSSI reporting

brcmfmac

* add support multi-scheduled scan

* add scheduled scan support for specified BSSIDs

* add support for brcm43430 revision 0

wlcore

* add wil1285 compatible

rsi

* add RS9113 USB support

iwlwifi

* FW API documentation improvements (for tools and htmldoc)

* continuing work for the new A000 family

* bump the maximum supported FW API to 31

* improve the differentiation between 8000, 9000 and A000 families
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 14:45:34 -04:00
Timur Tabi
ceef551faa net: qcom/emac: add support for emulation systems
On emulation systems, the EMAC's internal PHY ("SGMII") is not present,
but is not needed for network functionality.  So just display a warning
message and ignore the SGMII.

Tested-by: Philip Elcan <pelcan@codeaurora.org>
Tested-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:44:29 -04:00
Timur Tabi
867ae6abc2 net: qcom/emac: do not reset the EMAC during initialization
On ACPI systems, the driver depends on firmware pre-initializing the
EMAC because we don't have access to the clocks, and the EMAC has specific
clock programming requirements.  Therefore, we don't want to reset the
EMAC while we are completing the initialization.

Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:44:29 -04:00
Timur Tabi
03eb3eb4d4 net: qcom/emac: add shutdown function
The shutdown function halts all DMA and interrupts, so that all
operations are discontinued when the system shuts down, e.g. via
kexec or a forced reboot.

Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:44:29 -04:00
Dan Carpenter
64b2f72671 net: dsa: mv88e6xxx: fix error code in mv88e6390_serdes_power()
We're accidentally returning the wrong variable.  "cmode" is
uninitialized at this point so it causes a static checker warning.

Fixes: 6335e9f244 ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:33 -04:00
Simon Horman
24a021ed77 nfp: add VF and PF representors to flower app
Initialise VF and PF representors in flower app.

Based in part on work by Benjamin LaHaise, Bert van Leeuwen and
Jakub Kicinski.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:02 -04:00
Simon Horman
1025351a88 nfp: add flower app
Add app for flower offload. At this point the PF netdev and phys port
representor netdevs are initialised. Follow-up work will add support for
VF and PF representors and beyond that offloading the flower classifier.

Based in part on work by Benjamin LaHaise and Bert van Leeuwen.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:02 -04:00
Simon Horman
948faa46c0 nfp: add support for control messages for flower app
In preparation for adding a new flower app - targeted at offloading
the flower classifier - provide support for control message that it will
use to communicate with the NFP.

Based in part on work by Bert van Leeuwen.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Simon Horman
91bf82ca9e nfp: add support for tx/rx with metadata portid
Allow tx/rx with metadata port id. This will be used for tx/rx of
representor netdevs acting as upper-devices while a pf netdev acts
as a lower-device.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Simon Horman
93da7d9660 nfp: provide nfp_port to of nfp_net_get_mac_addr()
Provide port rather than vNIC as parameter of nfp_net_get_mac_addr.
This is to allow this function to be used by representor netdevs where
a vNIC may have more than one physical port none of which are associated
with the vNIC.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Simon Horman
758238f2e7 nfp: app callbacks for SRIOV
Add app-callbacks for app-specific initialisation of SRIOV.

Disabling SRIOV is brought forward in nfp_pci_remove()
so that nfp_app_sriov_disable is called while the app still exists.

This is intended to be used to implement representor netdevs for virtual
ports.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Simon Horman
eadfa4c3be nfp: add stats and xmit helpers for representors
Provide helpers for stats and xmit on representor netdevs.

Parts based on work by Bert van Leeuwen, Benjamin LaHaise and
Jakub Kicinski.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Simon Horman
5de73ee467 nfp: general representor implementation
Provide infrastructure to create and destroy representors of a given type.

Parts based on work by Bert van Leeuwen, Benjamin LaHaise,
and Jakub Kicinski.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Simon Horman
a5950182c0 nfp: map mac_stats and vf_cfg BARs
If present map mac_stats and vf_cfg BARs. These will be used by
representor netdevs to read statistics for phys port and vf representors.

Also provide defines describing the layout of the mac_stats area.
Similar defines are already present for the cf_cfg area.

Based in part on work by Jakub Kicinski.

Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Jakub Kicinski
a7ceb9905e nfp: move physical port init into a helper
Move MAC/PHY port init into a helper to make it easier to reuse
it in the representor code.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Jakub Kicinski
9daee04ae1 nfp: devlink add support for getting eswitch mode
Add app callback for reporting eswitch mode.  Non-SRIOV apps
should not implement this callback, nfp_app code will then
respond with -EOPNOTSUPP.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-25 11:42:01 -04:00
Florian Fainelli
bedd00c81b net: dsa: bcm_sf2: Remove special handling of "internal" phy-mode
The PHY library now supports an "internal" phy-mode, thus making our
custom parsing code now unnecessary.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 15:06:43 -04:00
Florian Fainelli
40bc8b065e net: bcmgenet: Remove special handling of "internal" phy-mode
The PHY library now supports an "internal" phy-mode, thus making our
custom parsing code now unnecessary.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 15:06:43 -04:00
David S. Miller
d4d0249ae2 mlx5-updates-2017-06-23
This series provides some updates to the mlx5 core and netdevice drivers.
 
 Three patches from Tariq, Introduces page reuse mechanism in non-Striding
 RQ RX datapath, we allow the the RX descriptor to reuse its allocated page
 as much as it could, until the page is fully consumed. RX page reuse
 reduces the stress on page allocator and improves RX performance especially
 with high speeds (100Gb/s).
 
 Next four patches of the series from Or allows to offload tc flower matching
 on ttl/hoplimit and header re-write of hoplimit.
 
 The rest of  the series from Yotam and Or enhances mlx5 to support FW flashing
 through the mlxfw module, in a similar manner done by the mlxsw driver.
 Currently, only ethtool based flashing is implemented, where both Eth and IB ports
 are supported.
 
 Thanks,
 Saeed.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJZTR2/AAoJEEg/ir3gV/o+HHkH/jA8uoIQgsIKP8+D6ppwChCm
 pcNpNWi5eWjBwRbeDKqTVRtmKEapFf2bjhWaegsybr7oGhzyh+t6nvCEiJVoKLpd
 gmcSKy7nY2PSepuMEg7bqlfj5caS3b0Nlz5sqPdclOXKYDVLytvcelOvr9OnqdAT
 JqxWkJMhEpLSgFniuvIyc1uJq9j6ARW7SYWx/dKp+gTDI2KCwQ3DinsrZ+RPh42F
 rxLFhGkcFuQ5cIr3QIdCM+pbr6LlAf2Fvz1Y791BARZg0XZp149C0c4smieEjU9M
 ya9CWlbSvnsYZcSMXtUO8ETnrtvrEfcEM0MpZo8l4y28eWih/Ib5BiHevQG3wHA=
 =L44M
 -----END PGP SIGNATURE-----

Merge tag 'mlx5-updates-2017-06-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
mlx5-updates-2017-06-23

This series provides some updates to the mlx5 core and netdevice drivers.

Three patches from Tariq, Introduces page reuse mechanism in non-Striding
RQ RX datapath, we allow the the RX descriptor to reuse its allocated page
as much as it could, until the page is fully consumed. RX page reuse
reduces the stress on page allocator and improves RX performance especially
with high speeds (100Gb/s).

Next four patches of the series from Or allows to offload tc flower matching
on ttl/hoplimit and header re-write of hoplimit.

The rest of  the series from Yotam and Or enhances mlx5 to support FW flashing
through the mlxfw module, in a similar manner done by the mlxsw driver.
Currently, only ethtool based flashing is implemented, where both Eth and IB ports
are supported.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:24:28 -04:00
Arjun Vynipadath
8f46d46715 cxgb4: Use Firmware params to get buffer-group map
Buffer group mappings can be obtained using FW_PARAMs cmd for newer FW.

Since some of the bg_maps are obtained in atomic context, created another
t4_query_params_ns(), that wont sleep when awaiting mbox cmd completion.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:22:39 -04:00
Arjun Vynipadath
193c4c2845 cxgb4: Update T6 Buffer Group and Channel Mappings
We were using t4_get_mps_bg_map() for both t4_get_port_stats()
to determine which MPS Buffer Groups to report statistics on for a given
Port, and also for t4_sge_alloc_rxq() to provide a TP Ingress Channel
Congestion Map.  For T4/T5 these are actually the same values (because they
are ~somewhat~ related), but for T6 they should return different values
(T6 has Port 0 associated with MPS Buffer Group 0 (with MPS Buffer Group 1
silently cascading off) and Port 1 is associated with MPS Buffer Group 2
(with 3 cascading off)).

Based on the original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:22:39 -04:00
Netanel Belgazal
8523899912 net: ena: update ena driver to version 1.2.0
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:11 -04:00
Netanel Belgazal
11a9a46019 net: ena: update driver's rx drop statistics
rx drop counter is reported by the device in the keep-alive
event.
update the driver's counter with the device counter.

Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:11 -04:00
Netanel Belgazal
3ae5907c61 net: ena: use lower_32_bits()/upper_32_bits() to split dma address
In ena_com_mem_addr_set(), use the above functions to split dma address
to the lower 32 bits and the higher 16 bits.

Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:10 -04:00
Netanel Belgazal
4265114d53 net: ena: separate skb allocation to dedicated function
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:10 -04:00
Netanel Belgazal
e745dafab0 net: ena: use napi_schedule_irqoff when possible
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:10 -04:00
Netanel Belgazal
06443684da net: ena: allow the driver to work with small number of msix vectors
Current driver tries to allocate msix vectors as the number of the
negotiated io queues. (with another msix vector for management).
If pci_alloc_irq_vectors() fails, the driver aborts the probe
and the ENA network device is never brought up.

With this patch, the driver's logic will reduce the number of IO
queues to the number of allocated msix vectors (minus one for management)
instead of failing probe().

Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:10 -04:00
Netanel Belgazal
ad974baef2 net: ena: add support for out of order rx buffers refill
ENA driver post Rx buffers through the Rx submission queue
for the ENA device to fill them with receive packets.
Each Rx buffer is marked with req_id in the Rx descriptor.

Newer ENA devices could consume the posted Rx buffer in out of order,
and as result the corresponding Rx completion queue will have Rx
completion descriptors with non contiguous req_id(s)

In this change the driver holds two rings.
The first ring (called free_rx_ids) is a mapping ring.
It holds all the unused request ids.
The values in this ring are from 0 to ring_size -1.

When the driver wants to allocate a new Rx buffer it uses the head of
free_rx_ids and uses it's value as the index for rx_buffer_info ring.
The req_id is also written to the Rx descriptor

Upon Rx completion,
The driver took the req_id from the completion descriptor and uses it
as index in rx_buffer_info.
The req_id is then return to the free_rx_ids ring.

This patch also adds statistics to inform when the driver receive out
of range or unused req_id.

Note:
free_rx_ids is only accessible from the napi handler, so no locking is
required

Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:09 -04:00
Netanel Belgazal
e2eed0e307 net: ena: add reset reason for each device FLR
For each device reset, log to the device what is the cause
the reset occur.

Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:09 -04:00
Netanel Belgazal
917501109c net: ena: change sizeof() argument to be the type pointer
Instead of using:
memset(ptr, 0x0, sizeof(struct ...))
use:
memset(ptr, 0x0, sizeor(*ptr))

Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-23 14:15:09 -04:00