The implementation of cris_console_device() is exactly the same as
uart_console_device(), so let's switch to use uart_console_device().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP h/w-assisted IXON flow control is borked. The transmitter becomes
stuck if XON is never received; clearing the fifos or resetting the
rx flow control bits has no effect.
Remove auto-IXANY as well, since without auto-IXON, it has no purpose.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to Advisory 21 as documented in AM437x errata document,
UART module cannot be disabled once DMA is used. The only
workaround is to softreset the module before disabling it.
DRA7x UARTs are compatible to AM437x UARTs in terms of
this errata and prescribed workaround.
Enable usage of workaround for this errata on DRA7x SoCs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM335x, AM437x and DRA7x SoCs have an errata[1] due to which UART
cannot be idled after it has been used with DMA.
OMAP3 has a similar sounding errata which has been worked around
in a2fc36613a ("ARM: OMAP3: Use manual idle for UARTs
because of DMA errata"). But the workaround used there does not
apply to AM335x, AM437x SoCs.
After using DMA, the UART module on these SoCs must be soft reset
to go to idle.
This patch implements that errata workaround. It is expected that
UART will be used with DMA so no explicit check for DMA usage
has been added for errata applicability.
MDR1 register needs to be restored right after soft-reset because
"UART mode" must be set in that register for module wake-up on AM335x
to work. As a result, SCR register is now used to determine if
context was lost during sleep.
[1] See Advisory 21 in AM437x errata SPRZ408B, updated April 2015.
http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of of_machine_is_compatible() for handling AM335x specific
"DMA kick" quirk in 8250_omap driver makes it ugly to extend the
quirk for other platforms. Instead use a new compatible.
The new compatible will also make it easier to take care of
other quirks on AM335x and like SoCs.
In order to not break backward DTB compatibility for users of
8250_omap driver on AM335x based boards, existing use of
of_machine_is_compatible() has not been removed.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The silicon errata[1] workaround implemented in a follow-on
patch, "serial: 8250_omap: workaround errata on disabling
UART after using DMA", requires MDR1 register programming.
Extract MDR1 register update into helper function,
omap8250_update_mdr1() to help with that.
[1] Advisory 21 in http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The compatible "ti,am4372-uart" is used in arch/arm/boot/dts/am4372.dtsi
but not documented. Add necessary documentation.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_device infrastructure has a suspend_noirq hook which
runtime suspends all devices late in the suspend cycle (see
_od_suspend_noirq() in arch/arm/mach-omap2/omap_device.c)
This leads to a NULL pointer exception in 8250_omap driver
since by the time omap8250_runtime_suspend() is called, 8250_dma
driver has already set rxchan to NULL via serial8250_release_dma().
Make an explicit check to see if rxchan is NULL in
runtime_{suspend|resume} hooks to fix this.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a data corruption bug when using discard on top of MD linear,
raid0 and raid10 personalities.
Commit 20d0189b10 "block: Introduce new bio_split()" permits sharing
the bio_vec between the two resulting bios. That is fine for read/write
requests where the bio_vec is immutable. For discards, however, we need
to be able to attach a payload and update the bio_vec so the page can
get mapped to a scatterlist entry. Therefore the bio_vec can not be
shared when splitting discards and we must do a full clone.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Seunguk Shin <seunguk.shin@samsung.com>
Tested-by: Seunguk Shin <seunguk.shin@samsung.com>
Cc: Seunguk Shin <seunguk.shin@samsung.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: <stable@vger.kernel.org> # v3.14+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fintek chip can be configured for io addresses different than the standard.
Query the chip for the configured addresses and try to match it with the
pnp address.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chip can be configured to use entry key different than 0x77. Try all the
valid keys until one gives out the right chip id.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some chips with the same interface but different chip ip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be connected at address 0x4e and also 0x2e.
Add some logic to find out the address of the chip.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save the port index and the line id in a private structure.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In little endian cases, macro htons unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_htons and htons expand directly to the same expression.
So, replace __constant_htons with htons with the goal of getting
rid of the definition of __constant_htons completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_htons(x)
+ htons(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 3873e2d7f6 ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling signalling char, claim the termios write lock before
signalling waiting readers and writers to prevent further i/o
before flushing the echo and output buffers. This prevents a
userspace signal handler which may output from racing the terminal
flush.
Reference: Bugzilla #99351 ("Output truncated in ssh session after...")
Fixes: commit d2b6f44779 ("n_tty: Fix signal handling flushes")
Reported-by: Filipe Brandenburger <filbranden@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On pm8xxx PMICs, shutdown and restart are signaled to the PMIC via a pin
called PS_HOLD. When this pin goes low, the PMIC performs a configurable
power sequence. Add a .shutdown hook so that we can properly configure this
power sequence for shutdown or restart depending on the system state.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen. Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.
According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.
The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Cc: stable@vger.kernel.org
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The micrel ks8851 device is present on MSM8960 CDP boards. It is
connected to two regulators, one controlled via a gpio and
another controlled via the RPM. Add the gsbi, spi, gpio
regulator, and micrel ks8851 nodes so that ethernet works
properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add RPM regulators and configure their constraints on the MSM8960
CDP so that we can control these supplies.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add the basic RPM and RPM regulator nodes that boards can fill in
with their board specific details.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Now that we have a proper pinctrl driver for the gpio block we
can change the compatible field here and configure the pinmux on
msm8960 devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Replace the standalone gpio driver with pinctrl-msm as we now have
msm8660 support there.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
ACPICA commit 8580ce04c1b7aa415c364b06e79edb8aca77dded
Version 20150717.
Link: 8580ce04
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit add72dca18ab5d02f1bf9b08027570e58da520e8
This mode will emit AML byte code after each ASL statement.
This is a prototype only and requires additional development.
This patch only affects ACPICA disassembler which is not in the kernel
source tree.
Link: add72dca
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 2164923d60429eea7cd5a4a8629b607af7325afa
Some disassembler APIs should rather be debugger APIs. This patch moves
them to the debugger folder to be ready for debugger porting.
Since there is no in-kernel ACPICA debugger in the kernel source tree, this
patch doesn't affect the Linux kernel.
Link: 2164923d
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 310e0ae1c4730f4dadc80125125099ab76851499
arg_types in struct acpi_db_method_info is only referenced by ACPI_DEBUGGER.
This patch only affects ACPICA debugger which is only used by a non-kernel
tool - acpiexec, so Linux kernel is currently not affected by this patch.
Link: 310e0ae1
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 55fa9555c71eaa99daebed4cd82cfde3875e8c45
In addition to the existing support for the client table.
Link: 55fa9555
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f88814201e01043a4f8caa69a69b799af11c44a3
These were defined in two places. Changed to ACPI_SIGN* names
and define them once in acmacros.h
This patch doesn't affect Linux kernel.
Link: f8881420
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7c490c28a18b435c543c6b410e7e7c2131fccc78
ACPICA implements all non-ANSI functions locally. However, there
are sometimes two or more versions of the same function throughout
the ACPICA code. This change fixes this.
Adds a new file, utilities/utnonansi.c
Link: 7c490c28
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 49c6a6517a906900e9baa51ad5859beeb8a3089f
The following error logs can be seen for calloc/free/malloc/realloc that
defined in the stdlib.h:
...\stdlib.h(281) : error C2059: syntax error : ','
...\stdlib.h(281) : error C2143: syntax error : missing ')' before 'constant'
...\stdlib.h(281) : error C2143: syntax error : missing '{' before 'constant'
...\stdlib.h(281) : error C2059: syntax error : '<Unknown>'
...\stdlib.h(281) : error C2059: syntax error : ')'
This is caused by the wrong inclusion order of stdlib.h/crtdbg.h introduced
in acenv.h. This patch fixes this breakage. Lv Zheng.
This patch doesn't affect Linux kernel.
Link: 49c6a651
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit eb9f8cb9fd65f1149dd335d05944c31cbca41af3
1) Warn if a Local is set but never used
2) Warn if a arg_x is never used (for non-predefined method names)
3) Warn if a arg_x that is used as a local is never used
This patch only affects iASL which is not in the kernel source tree.
Link: eb9f8cb9
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f9fd6e8bad0f16ce2b436c5cda36ced0c2d85302
Reported by Markus Elfring.
Link: f9fd6e8b
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c832b0a9263c560b3ae3ae31d7298ef33988f8d5
This patch removes one redundant debugging output of opcode execution which
has already been covered by acpi_ex_start_trace_opcode(). Lv Zheng.
Link: c832b0a9
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 61e9e20aadfaa03184d0959fbdc1fa5cdfea2551
This patch adds option to bypass opcode tracing. The option can be used to
reduce the trace message output. Lv Zheng.
Link: 61e9e20a
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit e8e4a9b19d0b72a7b165398bdc961fc2f6f502ec
This patch adds OSL trace hook support.
OSPMs are encouraged to use acpi_os_trace_point() with
ACPI_USE_SYSTEM_TRACER defined to implement platform specific trace
facility. Lv Zheng.
Link: e8e4a9b1
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 07fffd02607685b655ed92ee15c160e6a810b60b
The acpi_debug_trace() is the mechanism known as ACPI method tracing that is
used by Linux as ACPICA debugging message reducer. This facility can be
controlled through Linux ACPI subsystem - /sys/module/acpi/parameters.
This facility requires CONFIG_ACPI_DEBUG to be enabled to see ACPICA trace
logs in the kernel dmesg output.
This patch enhances acpi_debug_trace() to make it not only a message reducer,
but a real tracer to trace AML interpreter execution. Note that in addition
to the AML tracer enabling, this patch also updates the facility with the
following enhancements:
1. Allow a full path to be specified by the acpi_debug_trace() API.
2. Allow any method rather than just the entrance of acpi_evaluate_object()
to be traced.
3. All interpreter ACPI_LV_TRACE_POINT messages are collected for
ACPI_EXECUTER layer.
The Makefile of drivers/acpi/acpica is also updated to include exdebug.o
and the duplicated stubs are removed after that.
Note that since this patch has enhanced the method tracing facility, Linux
need also be updated after applying this patch. Lv Zheng.
Link: 07fffd02
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 71299ec8b49054daace0df50268e8e055654ca37
This patch adds trace point at the following point:
1. Begin/end of a control method execution;
2. Begin/end of an opcode execution.
The trace point feature can be enabled by defining ACPI_DEBUG_OUTPUT
and specifying a debug level that includes ACPI_LV_TRACDE_POINT and the
debug layers that include ACPI_PARSER and ACPI_DISPACTCHER.
In order to make aml_op_name of union acpi_parse_object usable for tracer, it is
enabled for ACPI_DEBUG_OUTPUT in this patch. Lv Zheng.
Link: 71299ec8
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c8275e243b58fd4adfc0362bd704af41ed14bc75
This patch moves parts of acpi_dm_dump_method_info() to the dispatcher
component.
This patch also makes the new function dependent on ACPI_DEBUG_OUTPUT
compile-stage definition so that it can be used by the trace facility.
acpi_dm_dump_method_info() traverses method stack when an exception is
encountered. Such traversal is needed to support method tracing for the
exceptions. When an exception is encountered, the end indications of the
aborted methods should be logged in order not to break the user space
analysis tool. Lv Zheng.
Link: c8275e24
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 6e0229bb156d71675f2e07dc7960adb7ec0a60ea
This patch adds functions to return normalized full path instead of
"external path". The external path contains trailing "_" for each
name segment while the normalized full path doesn't contain the
trailing "_".
Currently this function is used by the method tracing users to specify a
none trailing "_" attached name path. Lv Zheng.
Note that we need to validate and switch all Linux kernel acpi_get_name()
users to use the new name type before removing the old name type from
ACPICA.
Link: 6e0229bb
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reviewed-by: Ruiyi Zhang <ruiyi_zhang@hotmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 9dcd124e914e87495fbd1786d9484b962e0823e0
This patch adds back pointing reference of the namespace node for a method
operand. The namespace node then can be used in
acpi_ds_terminate_control_method() to obtain method full path to be used by
tracing facilities. Lv Zheng.
Link: 9dcd124e
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit afb52611dbe7403551f93504d3798534f5c343f4
This patch cleans up the code of assigning the AML address to the
union acpi_operand_object.
The idea behind this cleanup is:
The AML address of the union acpi_operand_object should always be determined at
the point where the object is encountered. It should be started from the
first byte of the object. For example, the opcode of the object, the name
string of the user_term object, or the first byte of the packaged object
(where a pkg_length is prefixed). So it's not cleaner to have it assigned
here and there in the entire ACPICA source tree.
There are some special cases for the internal opcodes, before cleaning up
the internal opcodes, we should also determine the rules for the AML
addresses of the internal opcodes:
1. INT_NAMEPATH_OP: the address of the first byte for the name_string.
2. INT_METHODCALL_OP: the address of the first byte for the name_string.
3. INT_BYTELIST_OP: the address of the first byte for the byte_data list.
4. INT_EVAL_SUBTREE_OP: the address of the first byte for the
Region/Package/Buffer/bank_field/Field arguments.
5. INT_NAMEDFIELD_OP: the address to the name_seg.
6. INT_RESERVEDFIELD_OP: the address to the 0x00 prefix.
7. INT_ACCESSFIELD_OP: the address to the 0x01 prefix.
8. INT_CONNECTION_OP: the address to the 0x02 prefix.
9: INT_EXTACCESSFIELD_OP: the address to the 0x03 prefix.
10.INT_RETURN_VALUE_OP: the address of the replaced operand.
11.computational_data: the address to the
Byte/Word/Dword/Qword/string_prefix.
Before cleaning up the internal root scope of the aml_walk, turning it into
the term_list, we need to remember the aml_start address as the "Aml"
attribute for the union acpi_operand_object created by acpi_ps_create_scope_op().
Finally, we can delete some redundant AML address assignment in psloop.c.
Link: afb52611
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
