This patch adds a secondary_startup entry point to head-nommu.S so that
we can boot secondary CPUs on an SMP nommu configuration.
Signed-off-by: Will Deacon <will.deacon@arm.com>
CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Nicolas Pitre <nico@linaro.org>
Don't enable the cursor until g4x_fixup_plane() had a chance to do
cast its magic spell.
Egbert writes:
"Today I had the chance to test this. First I tried
if I can still reproduce the blank with this patch
added when I disable my voodoo g4x_fixup_plane():
It turned out it still happens however very rarely
(like 1 out of 20 tries). When I reenabled my voodoo
the issue still occurred.
I had to switch two lines around, ie:
intel_enable_plane(dev_priv, plane, pipe);
if (IS_G4X(dev))
g4x_fixup_plane(dev_priv, pipe);
+ intel_crtc_update_cursor(crtc, true);
to avoid the blank screen issue - which is it didn't
happen in ~75 tries."
v2: Add a comment to remind people of the ordering constraints
Acked-by: Egbert Eich <eich@suse.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required for tracking render damage for use with FBC and will be
used in subsequent patches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though they are virtual widgets DAI widgets still get counted for the
DAPM context power management so we can't just use the active state to
check if they should be powered as they may not be part of a complete path.
Instead split them into input and output widgets and do the same power
checks as we perform on AIFs.
Reported-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide EL2 with page tables and stack, and set the vectors
to point to the full blown world-switch code.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Let userspace play with the guest registers.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Define the necessary structures to perform an MMIO access.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide the architecture dependent structures for VM and
vcpu abstractions.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide the reset code for a virtual CPU booted in 64bit mode.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the support code for CPU specific system registers. Not much
here yet.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide 64bit system register handling, modeled after the cp15
handling for ARM.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide the kvm.h file that defines the user space visible
interface.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Implement the injection of a fault (undefined, data abort or
prefetch abort) into a 64bit guest.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Implements helpers for dealing with the EL2 syndrome register as
well as accessing the vcpu registers.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Define the saved/restored registers for 64bit guests.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Define all the useful bitfields for EL2 registers.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the necessary infrastructure for identity-mapped HYP page
tables. Idmap-ed code must be in the ".hyp.idmap.text" linker
section.
The rest of the HYP ends up in ".hyp.text".
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add HYP and S2 page flags, for both normal and device memory.
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move cpufreq driver of powerpc platform to drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit ac212b6 (ACPI / processor: Use common hotplug
infrastructure) the acpi-cpufreq module is not loaded automatically
by udev which fails to match it against the x86cpu modalias. Still,
it can be matched against ACPI processor device IDs, which even
makes more sense, because it depends on the ACPI processor driver
that uses those device IDs to bind to processor devices.
For this reason, add ACPI processor device IDs to acpi-cpufreq.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
We need to select CPU_FREQ_TABLE in order to build without
this kind of errors:
drivers/built-in.o: In function `kirkwood_cpufreq_cpu_exit':
/home/zeta/linux-devel/marvell-legacy/drivers/cpufreq/kirkwood-cpufreq.c:145:
undefined reference to `cpufreq_frequency_table_put_attr'
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Like a lot of the other cpufreq drivers, this one needs to
select CONFIG_CPU_FREQ_TABLE to avoid a build error like
built-in.o: In function `bL_cpufreq_set_target':
cpufreq/arm_big_little.c:71: undefined reference to `cpufreq_frequency_table_target'
built-in.o: In function `bL_cpufreq_verify_policy':
cpufreq/arm_big_little.c:55: undefined reference to `cpufreq_frequency_table_verify'
built-in.o: In function `bL_cpufreq_init':
cpufreq/arm_big_little.c:170: undefined reference to `cpufreq_frequency_table_cpuinfo'
cpufreq/arm_big_little.c:178: undefined reference to `cpufreq_frequency_table_get_attr'
built-in.o:(.data+0x5a80c): undefined reference to `cpufreq_freq_attr_scaling_available_freqs'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Like a lot of the other cpufreq drivers, this one needs to
select CONFIG_CPU_FREQ_TABLE to avoid a build error like
drivers/built-in.o: In function `spear_cpufreq_exit':
spear-cpufreq.c:198: undefined reference to `cpufreq_frequency_table_put_attr'
drivers/built-in.o: In function `spear_cpufreq_verify':
spear-cpufreq.c:35: undefined reference to `cpufreq_frequency_table_verify'
drivers/built-in.o: In function `spear_cpufreq_init':
spear-cpufreq.c:181: undefined reference to `cpufreq_frequency_table_cpuinfo'
spear-cpufreq.c:187: undefined reference to `cpufreq_frequency_table_get_attr'
drivers/built-in.o: In function `spear_cpufreq_target':
spear-cpufreq.c:120: undefined reference to `cpufreq_frequency_table_target'
drivers/built-in.o:(.data+0x5e63c): undefined reference to `cpufreq_freq_attr_scaling_available_freqs'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: cpufreq@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Introduce CONFIG_XEN and the implementation of hypercall.S (that is
the only ARMv8 specific code in Xen support for ARM).
Compile enlighten.c and grant_table.c from arch/arm.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
asm/xen/hypercall.h, asm/xen/hypervisor.h, asm/xen/interface.h and
asm/xen/page.h are identical so to avoid code duplication we are just
including the original arm header files here.
asm/xen/events.h is slightly different, so introduce a different file
here (use xchg to implement xchg_xen_ulong and pass regs->pstate to
raw_irqs_disabled_flags).
Also introduce asm/hypervisor.h and asm/sync_bitops.h.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
* pm-fixes:
cpufreq: cpufreq-cpu0: use the exact frequency for clk_set_rate()
cpufreq: protect 'policy->cpus' from offlining during __gov_queue_work()
acpi-cpufreq: set current frequency based on target P-State
* acpi-fixes:
ACPI / PM: Do not execute _PS0 for devices without _PSC during initialization
ACPI / scan: do not match drivers against objects having scan handlers
ACPI / APEI: fix error return code in ghes_probe()
ACPI / video: ignore BIOS initial backlight value for HP Pavilion g6
ACPI / video: ignore BIOS initial backlight value for HP m4
x86 / platform / hp_wmi: Fix bluetooth_rfkill misuse in hp_wmi_rfkill_setup()
Commit b378549 (ACPI / PM: Do not power manage devices in unknown
initial states) added code to force devices without _PSC, but having
_PS0 defined in the ACPI namespace, into ACPI power state D0 by
executing _PS0 for them. That turned out to break Toshiba P870-303,
however, so revert that code.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58201
Reported-and-tested-by: Jerome Cantenot <jerome.cantenot@gmail.com>
Tracked-down-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add regulator_get_linear_step(), which returns the voltage step size
between VSEL values for linear regulators. This is intended for use
by regulator consumers which build their own voltage-to-VSEL tables.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Document the device tree binding for the WM8962 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work of WM8903 by Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When booting the kernel, a bootloader could have left the virtual
timer ticking away, potentially generating interrupts. This could
be troublesome if the user of the virtual timer is not careful
when enabling the interrupt.
In order to avoid any surprise, stop the virtual timer from
interrupting us when booted in HYP mode, as we'll use the physical
timer in this case.
Reported-by: Giridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Dave Martin <dave.martin@linaro.org>
In 8a4da6e: "arm: arch_timer: move core to drivers/clocksource", the
selection of ARM_ARCH_TIMER was indirected via HAVE_ARM_ARCH_TIMER,
though mach-exynos's selection of ARM_ARCH_TIMER was missed, and since
then mach-shmobile, mach-tegra, and mach-virt have begun selecting
ARM_ARCH_TIMER. This can lead to architected timer support erroneously
appearing to not be selected in menuconfig.
This patch fixes up the Kconfigs for those platforms to select
HAVE_ARM_ARCH_TIMER.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Switching between reading the virtual or physical counters is
problematic, as some core code wants a view of time before we're fully
set up. Using a function pointer and switching the source after the
first read can make time appear to go backwards, and having a check in
the read function is an unfortunate block on what we want to be a fast
path.
Instead, this patch makes us always use the virtual counters. If we're a
guest, or don't have hyp mode, we'll use the virtual timers, and as such
don't care about CNTVOFF as long as it doesn't change in such a way as
to make time appear to travel backwards. As the guest will use the
virtual timers, a (potential) KVM host must use the physical timers
(which can wake up the host even if they fire while a guest is
executing), and hence a host must have CNTVOFF set to zero so as to have
a consistent view of time between the physical timers and virtual
counters.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rob Herring <rob.herring@calxeda.com>
To use the virtual counters from the host, we need to ensure that
CNTVOFF doesn't change unexpectedly. When we change to a guest, we
replace the host's CNTVOFF, but we don't restore it when returning to
the host.
As the host sets CNTVOFF to zero, and never changes it, we can simply
zero CNTVOFF when returning to the host. This patch adds said zeroing to
the return to host path.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Christoffer Dall <cdall@cs.columbia.edu>
In order to be able to use the virtual counter in a safe way,
make sure it is initialized to zero before dropping to SVC.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Dave Martin <dave.martin@linaro.org>
Pull the code to disable trickle feed for all primary planes into a
separate function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable trickle feed in all the (relevant) clock gating functions,
except ironlake_init_clock_gating(). Copy paste the same code there as
well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec, trickle feed should be disabled for BW and
mobile CL. Those constraints seem to match all of our gen4 chipsets.
Trickle feed is disabled via the MI_ARB_STATE register instead of
per plane controls on gen4.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs say that the trickle feed disable bit is present (for primary
planes only, not video sprites) on CTG, and that it must be set
for ELK. Just set it for all g4x chipsets.
v2: Do it in init_clock_gating too
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We always limited the link bw calculations to 24bpp. Tested with
my shiny new high-bpc screen, seems to work as advertised.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65280
Tested-by: shui yangwei <yangweix.shui@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
marzen_init_late() should be static
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch is directly accessing to PUPR4 register which can
control SDHI0 CD/WP pin pull-up setting.
It should be replaced in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the marzen board to use the INTC External IRQ pin driver for SMSC.
This code was originally posted by Magnus Damm as part of
"ARM: shmobile: INTC External IRQ pin driver on r8a7779"
but somehow omitted when I applied that patch.
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
