The VAG_POWER must be enabled after all other bits in CHIP_ANA_POWER
and disabled before any other bit in CHIP_ANA_POWER. See the SGTL5000
datasheet (Table 31, BIT 7, page 42-43). Failing to follow this order
will result in ugly loud "POP" noise at the end of playback.
To achieve such order, use the _PRE and _POST DAPM widgets to trigger
the power_vag_event, where the event type check has to be fixed
accordingly as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes the following type of warnings:
drivers/spi/spi-topcliff-pch.c:370:52: warning:
Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Setting platform data to NULL is not necessary.
Also fixes the following sparse warning:
drivers/spi/spi-xilinx.c:508:35: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Do not load endian value from platform data
and rather autodetect it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is now a very simple trigger indeed but useful in many common cases.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Switching from one platform device registering a lot of triggers
to one for each trigger simplifies the code somewhat. It would be
relatively unusual to have more than a couple of such devices
registered so this change will not result in much additional overhead.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Also change all internal naming appropriately.
This trigger is no longer just for gpio provided interrupts so
change the naming to reflect this. Also drop some now missleading
left over comments.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The ISR currently consumes the rx buffer data and re-enables transmission
from within interrupt context. This is bad because if the interrupt
occurs again before the ISR exits, the new interrupt will be erroneously
cleared by the still completing ISR.
Simplified the ISR by just setting the completion variable and exiting with
no action. Then just looped the transmit functionality in
xilinx_spi_txrx_bufs().
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The data structure is required only when DT is enabled.
Hence compile it conditionally.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The code uses
return foo;
goto err_type;
when instead the form should have been
ret = foo;
goto err_type;
Here this causes a useful iio_device_put to be skipped.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If we pass an invalid clock type then "ts" is never set. We need to
check for errors earlier, otherwise we end up passing uninitialized
stack data to userspace.
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes one build failure which is introduced by the patch
below:
driver core: firmware loader: kill FW_ACTION_NOHOTPLUG requests
before suspend
When CONFIG_FW_LOADER_USER_HELPER is unset, kill_requests_without_uevent()
should be nop because no userspace loading is involved.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the SPI subsystem recently grew support to queue messages before handing
them to the SPI master, and erroneously emitted deprecation warnings
when the SPI master's driver did not use the common logic (in fact the
master might queue messages, but implement the queue in the master
driver's source)
[ 0.823015] mpc512x-psc-spi 80011400.psc: master is unqueued, this is deprecated
[ 0.854913] mpc512x-psc-spi 80011500.psc: master is unqueued, this is deprecated
this change makes the MPC512x PSC SPI driver use the SPI subsystem's
support to queue SPI messages and removes the master driver's private
code for the queue support
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
change the MPC512x SPI controller's transmission routine to increase
throughput: allow the RX byte counter to "lag behind" the TX byte
counter while iterating over the transfer's data, only wait for the
remaining RX bytes at the very end of the transfer
this approach eliminates delays in the milliseconds range, transfer
times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct
operation was tested by continuously transferring and comparing data
from an SPI flash (more than 200GB in some 45 hours)
background information on the motivation:
one might assume that all the RX data should have been received when the
TX data was sent, given the fact that we are the SPI master and provide
all of the clock, but in practise there's a difference
the ISR is triggered when the TX FIFO became empty, while transmission
of the last item still occurs (from the TX hold and shift registers),
sampling RX data on the opposite clock edge compared to the TX data adds
another delay (half a bit period), and RX data needs to propagate from
the reception buffer to the RX FIFO depending on the specific SoC
implementation
to cut it short: a difference between TX and RX byte counters during
transmission is not just acceptable but should be considered the regular
case, only the very end of the transfer needs to make sure that all of
the RX data was received before deasserting the chip select and telling
the caller that transmission has completed
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
mechanical edits before changing functionality, to reduce diffs
- rename variables to later tell remaining TX and RX apart
- use size_t for the current TX and RX length
(for better compatibility with the min() macro)
- remove unused members from the master data (sysclk, eofbyte)
- silence a checkpatch warning (braces around single statement)
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Later we would like to clear PageWriteback bit only after extent
conversion from unwritten to written extents is performed. However it
is not possible to start a transaction after PageWriteback is set
because that violates lock ordering (and is easy to deadlock). So we
have to reserve a transaction before locking pages and sending them
for IO and later we use the transaction for extent conversion from
ext4_end_io().
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There isn't any need for setting BH_Uninit on buffers anymore. It was
only used to signal we need to mark io_end as needing extent
conversion in add_bh_to_extent() but now we can mark the io_end
directly when mapping extent.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There are two issues with current writeback path in ext4. For one we
don't necessarily map complete pages when blocksize < pagesize and
thus needn't do any writeback in one iteration. We always map some
blocks though so we will eventually finish mapping the page. Just if
writeback races with other operations on the file, forward progress is
not really guaranteed. The second problem is that current code
structure makes it hard to associate all the bios to some range of
pages with one io_end structure so that unwritten extents can be
converted after all the bios are finished. This will be especially
difficult later when io_end will be associated with reserved
transaction handle.
We restructure the writeback path to a relatively simple loop which
first prepares extent of pages, then maps one or more extents so that
no page is partially mapped, and once page is fully mapped it is
submitted for IO. We keep all the mapping and IO submission
information in mpage_da_data structure to somewhat reduce stack usage.
Resulting code is somewhat shorter than the old one and hopefully also
easier to read.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The register access to enable hardware flow control depends on the
device port number and not the port minor number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the no longer used endpoint-array access completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The outcont_endpoints array was indexed using the port minor number
(which can be greater than the array size) rather than the device port
number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus port-number check in open and close, which prevented this
driver from being used with a minor number different from zero.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We limit the number of blocks written in a single loop of
ext4_da_writepages() to 64 when inode uses indirect blocks. That is
unnecessary as credit estimates for mapping logically continguous run
of blocks is rather low even for inode with indirect blocks. So just
lift this limitation and properly calculate the number of necessary
credits.
This better credit estimate will also later allow us to always write
at least a single page in one iteration.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
ext4_ind_trans_blocks() wrongly used 'chunk' argument to decide whether
blocks mapped are logically contiguous. That is wrong since the argument
informs whether the blocks are physically contiguous. As the blocks
mapped are always logically contiguous and that's all
ext4_ind_trans_blocks() cares about, just remove the 'chunk' argument.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This attribute is now unused so deprecate it. We still show the old
default value to keep some compatibility but we don't allow writing to
that attribute anymore.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Writeback code got better in how it submits IO and now the number of
pages requested to be written is usually higher than original 1024.
The number is now dynamically computed based on observed throughput
and is set to be about 0.5 s worth of writeback. E.g. on ordinary
SATA drive this ends up somewhere around 10000 as my testing shows.
So remove the unnecessary smarts from ext4_da_writepages().
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
In some cases we cannot start a transaction because of locking
constraints and passing started transaction into those places is not
handy either because we could block transaction commit for too long.
Transaction reservation is designed to solve these issues. It
reserves a handle with given number of credits in the journal and the
handle can be later attached to the running transaction without
blocking on commit or checkpointing. Reserved handles do not block
transaction commit in any way, they only reduce maximum size of the
running transaction (because we have to always be prepared to
accomodate request for attaching reserved handle).
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
In summary, the symptom is intermittent key events lost after resume
on some machines with synaptics touchpad (seems this is synaptics _only_),
and key events loss is due to serio port reconnect after psmouse sync lost.
Removing psmouse and inserting it back during the suspend/resume process
is able to work around the issue, so the difference between psmouse_connect()
and psmouse_reconnect() is the key to the root cause of this problem.
After comparing the two different paths, synaptics driver has its own
implementation of synaptics_reconnect(), and the missing psmouse_probe()
seems significant, the patch below added psmouse_probe() to the reconnect
process, and has been verified many times that the issue could not be reliably
reproduced.
There are two PS/2 commands in psmouse_probe():
1. PSMOUSE_CMD_GETID
2. PSMOUSE_CMD_RESET_DIS
Only the PSMOUSE_CMD_GETID seems to be significant. The
PSMOUSE_CMD_RESET_DIS is irrelevant to this issue after trying
several times. So we have only implemented this patch to issue
the PSMOUSE_CMD_GETID so far.
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Signed-off-by: James M Leddy <james.leddy@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Define xen_remap as ioremap_cache (MT_MEMORY and MT_DEVICE_CACHED end up
having the same AttrIndx encoding).
Remove include asm/mach/map.h, not unneeded.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
j_wait_logspace and j_wait_checkpoint are unused. Remove them.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
jbd2_journal_extend() first checked whether transaction can accept
extending handle with more credits and then added credits to
t_outstanding_credits. This can race with start_this_handle() adding
another handle to a transaction and thus overbooking a transaction.
Make jbd2_journal_extend() use atomic_add_return() to close the race.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This is a driver for the keypads found on the TI-Nspire series calculators.
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
__jbd2_log_space_left() and jbd_space_needed() were kind of odd.
jbd_space_needed() accounted also credits needed for currently
committing transaction while it didn't account for credits needed for
control blocks. __jbd2_log_space_left() then accounted for control
blocks as a fraction of free space. Since results of these two
functions are always only compared against each other, this works
correct but is somewhat strange. Move the estimates so that
jbd_space_needed() returns number of blocks needed for a transaction
including control blocks and __jbd2_log_space_left() returns free
space in the journal (with the committing transaction already
subtracted). Rename functions to jbd2_log_space_left() and
jbd2_space_needed() while we are changing them.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The comment about credit estimates isn't true anymore. We do what the
comment describes now.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Currently when we add a buffer to a transaction, we wait until the
buffer is removed from BJ_Shadow list (so that we prevent any changes
to the buffer that is just written to the journal). This can take
unnecessarily long as a lot happens between the time the buffer is
submitted to the journal and the time when we remove the buffer from
BJ_Shadow list. (e.g. We wait for all data buffers in the
transaction, we issue a cache flush, etc.) Also this creates a
dependency of do_get_write_access() on transaction commit (namely
waiting for data IO to complete) which we want to avoid when
implementing transaction reservation.
So we modify commit code to set new BH_Shadow flag when temporary
shadowing buffer is created and we clear that flag once IO on that
buffer is complete. This allows do_get_write_access() to wait only
for BH_Shadow bit and thus removes the dependency on data IO
completion.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Similarly as for metadata buffers, also log descriptor buffers don't
really need the journal head. So strip it and remove BJ_LogCtl list.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When writing metadata to the journal, we create temporary buffer heads
for that task. We also attach journal heads to these buffer heads but
the only purpose of the journal heads is to keep buffers linked in
transaction's BJ_IO list. We remove the need for journal heads by
reusing buffer_head's b_assoc_buffers list for that purpose. Also
since BJ_IO list is just a temporary list for transaction commit, we
use a private list in jbd2_journal_commit_transaction() for that thus
removing BJ_IO list from transaction completely.
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Change writeback path to create just one io_end structure for the
extent to which we submit IO and share it among bios writing that
extent. This prevents needless splitting and joining of unwritten
extents when they cannot be submitted as a single bio.
Bugs in ENOMEM handling found by Linux File System Verification project
(linuxtesting.org) and fixed by Alexey Khoroshilov
<khoroshilov@ispras.ru>.
CC: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The patch adds support for THP (transparent huge pages) to LPAE
systems. When this feature is enabled, the kernel tries to map
anonymous pages as 2MB sections where possible.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[steve.capper@linaro.org: symbolic constants used, value of
PMD_SECT_SPLITTING adjusted, tlbflush.h included in pgtable.h,
added PROT_NONE support.]
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This patch adds support for hugetlbfs based on the x86 implementation.
It allows mapping of 2MB sections (see Documentation/vm/hugetlbpage.txt
for usage). The 64K pages configuration is not supported (section size
is 512MB in this case).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[steve.capper@linaro.org: symbolic constants replace numbers in places.
Split up into multiple files, to simplify future non-LPAE support,
removed huge_pmd_share code, as this is very rarely executed,
Added PROT_NONE support].
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
On ARM we use the __flush_dcache_page function to flush the dcache
of pages when needed; usually when the PG_dcache_clean bit is unset
and we are setting a PTE.
A HugeTLB page is represented as a compound page consisting of an
array of pages. Thus to flush the dcache of a HugeTLB page, one must
flush more than a single page.
This patch modifies __flush_dcache_page such that all constituent
pages of a HugeTLB page are flushed.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
