We never check the return values, and there's not much we could do on
errors anyway. Just simplify the signatures. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename all VLV IOSF sideband register accessor functions to
vlv_<port>_{read,write}. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both the intel_dpio_{read,write} and valleyview_{punit,nc}_{read,write}
use the IOSF sideband interface. They access the same registers and do
mostly the same stuff, but no shared code. There are even duplicate
register defines for the same registers. Both have locking, but the
former use dpio_lock and the latter rps.hw_lock. It's racy.
This patch refactors the sideband access to a single function that
expects dpio_lock to be held. The dpio_lock is only used for sideband
stuff, so it's a better match than rps.hw_lock for the purpose. The rps
stuff still needs rps.hw_lock, since it's used to protect more than just
the register access, so rps code will need to hold both locks.
Based on the work by Shobhit Kumar <shobhit.kumar@intel.com> and Yogesh
Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Group both the HSW/LPT SBI interface and VLV IOSF sideband register
accessor functions into a new file. No functional changes.
v2: also move intel_sbi_{read,write} (Daniel)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Moorestown
Revert "x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
Hotplug
PCI: acpiphp: Re-enumerate devices when host bridge receives Bus Check
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=M8/H
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Here are some more fixes for v3.10. The Moorestown update broke Intel
Medfield devices, so I reverted it. The acpiphp change fixes a
regression: we broke hotplug notifications to host bridges when we
split acpiphp into the host-bridge related part and the
endpoint-related part.
Moorestown
Revert "x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
Hotplug
PCI: acpiphp: Re-enumerate devices when host bridge receives Bus Check"
* tag 'pci-v3.10-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
PCI: acpiphp: Re-enumerate devices when host bridge receives Bus Check
Pull input updates from Dmitry Torokhov:
"A few fixups to Wacom and eGalax touchscreen driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add an eraser to DTH2242/DTK2241
Input: wacom - add a few new styli for Cintiq series
Input: wacom - add three new display tablets
Input: egalax_ts - ABS_MT_POSITION_Y not reported well
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately, advertising P2P_DEVICE support was a little
premature, a number of issues came up in testing and have
been fixed for 3.10. Rather than try to backport all the
different fixes, disable P2P_DEVICE support in the drivers
using it. For iwlmvm that implies disabling P2P completely
as it can't support P2P operation w/o P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These drivers are now operational and even use the latest common clk
and DMA APIs. There's no reason why we shouldn't start them up now.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cryp driver is currently silent and the Hash driver prints the
name of its probe function unnecessarily. Let's just put a nice
descriptive one-liner there instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Andreas Westin <andreas.westin@stericsson.com>
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DMA channel configuration information should be setup in the driver.
The Ux500 Cryp driver now does this, so there's no need to send it
though here too.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DMA controller currently takes configuration information from
information passed though dma_channel_request(), but it shouldn't.
Using the API, the DMA channel should only be configured during
a dma_slave_config() call.
Cc: David S. Miller <davem@davemloft.net>
Cc: Andreas Westin <andreas.westin@stericsson.com>
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we fail to prepare the ux500-cryp clock before enabling it the
platform will fail to boot. Here we insure this happens.
Cc: David S. Miller <davem@davemloft.net>
Cc: Andreas Westin <andreas.westin@stericsson.com>
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DMA channel configuration information should be setup in the driver.
The Ux500 Hash driver now does this, so there's no need to send it
though here too.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DMA controller currently takes configuration information from
information passed though dma_channel_request(), but it shouldn't.
Using the API, the DMA channel should only be configured during
a dma_slave_config() call.
Cc: David S. Miller <davem@davemloft.net>
Cc: Andreas Westin <andreas.westin@stericsson.com>
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we fail to prepare the ux500-hash clock before enabling it the
platform will fail to boot. Here we insure this happens.
Cc: David S. Miller <davem@davemloft.net>
Cc: Andreas Westin <andreas.westin@stericsson.com>
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DMA data width and packet size information is only required at channel
configuration time. Any information passed from platform data is passed
directly to the DMA40 driver to use during channel allocation, but these
pieces of information are subsequently ignored by the driver, so we may
as well remove them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DMA addresses are now passed as part of the dmaengine API by invoking
dmaengine_slave_config(). So there's no requirement for the DMA40
driver to look them up in a table provided by platform data. This
method does not fit in well using Device Tree either.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Addresses are now stored in local data structures and are easy to
obtain, thus a specialist function used to fetch them is now surplus
to requirement.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Addresses are passed in from the client's driver via the invocation of
dmaengine_slave_config(), so there's no need to fetch them from platform
data too, hardwired or otherwise. This is a great step forward, as it
elevates a large burden from platform data in the way of a look-up
table.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It was required to pass DMA channel configuration information to the
UART driver before the new DMA API was in place. Now that it is, and
is fully compatible with Device Tree we can stop doing that.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the dmaengine API for slave transfers, allocating and configuring
a channel are two separate actions. Here we're removing logical channel
configuration from the channel allocation routine for slave transfers,
as the same config is already done in the runtime config function, and
put the corresponding call into d40_config_memcpy() for the memcpy
code path.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Edited the commit message]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The majority of configuration done in d40_phy_config() pertains
to physical channels. Move the call over to runtime config which
has different code paths for physical and logical channels already,
and make it an exclusive physical channel config function as the
name implies, and drop the is_log argument.
Since we moved the call to runtime_config() it only gets called
for device transfers, so encode the small snippet of configuration
pertaining to memcpy channels into the d40_config_memcpy()
function.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[rewrote the commit message]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During the initial setup of a logical channel, it is necessary to unmask
the GIM in order to receive generated terminal count and error interrupts.
We're separating out this required code so it will be possible to move
the remaining code in d40_phy_cfg(), which is mostly runtime configuration
into the runtime_config() routine.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ironically, in order to remove lots of the auxdata assignments, we have
to add just one more. A lot of them require DMA information to be passed
into clients for DMA channel allocation, but we now have this capability
in Device Tree. However, the DMA40 driver still relies on a reverse table
look-up to obtain DMA addresses. Until all of the clients are converted,
over to the new API, we're stuck with this.
Also, now the DMA40 has been DT:ed, there's no requirement to register
it using traditional methods, so let's remove it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the new DMA DT bindings and API, we can register the DMA40 driver
as Device Tree capable. Now, when a client attempts to allocate a
channel using the DMA DT bindings via its own node, we are able to parse
the request and allocate a channel in the correct manner.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When booting using Device Tree, devices aren't registered in the normal
way. Instead, they need to be provided with a compatible string which is
held in an OF Match Table for comparison during start-up. Here we provide
the compatible string and prepare the driver to not receive a platform
data pointer.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Fixed up whitespace error]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's the way that most other drivers do it.
Very trivial clean-up which reduces line count and simplifies code.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now we know the total of physical and logical channels, we may as
well report them within the information log.
Before:
dma40 dma40.0: hardware revision: 3 @ 0x801c0000 with 8 physical channels
After:
<as above ...> and 256 logical channels
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At the moment we fetch the hardware revision, then do some stuff, then
check whether the revision is correct and return in error if it's not.
Well we may as well check it as soon as we know what it is, so let's
move the check right up underneath where we acquire the version.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before allocating memory for logical channels, the current driver
checks to see if there are any. Well as the dma40_memcpy_channels[]
array is always populated, the check is always true. Best to
remove the check.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change will cost ~25KB of memory, but it's worth the trade-off,
as it removes a great deal of overhead. It means that instead of only
allocating memory for the logical channels in use, it does so for all
available ones, which is 32 per physical channel. However, this now
means we can remove some platform data and we don't have to worry
about adding vendor specific variables to Device Tree.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'psize' is used to calculate the maximum DMA burst size. However it
is only taken into consideration when editing the DMA channel's
configuration. The Audio DMA platform data is only used to allocate
a channel, not configure it. That will be done at a later date within
the MSP driver.
We're also removing comments which are no longer required, as
'data_width' is no longer set in any device's platform data period.
Tested-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DMA configuration data is now allocated in the UART driver, so these
are just ignored.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DMA configuration data is now allocated in the SSP driver, so these
are just ignored.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DMA configuration data is now allocated in the MMCI driver, so these
are just ignored.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current implementation of the DMA40's local MAX() macro evaluates
its arguments more times than is necessary and it not type checked.
This patch strips replaces it with a new, more efficient constant.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For the moment at least, the TX and RX channels for DB8500 USB are
identical, so this patch generalises them into a single structure
and passes it twice. Once as the TX and again for the RX configuration.
We're keeping the infrastructure the same i.e. passing the TX and RX
separately in case they start to differ on latter incarnations of the
platform.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices which utilise DMA use the same device numbers for transmitting
and receiving. In this patch we encode the source and destination
information into one single attribute. We can subsequently exploit the
direction attribute to see which of the transfer directions are being
described. This also lessens the burden on platform data.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we compare an event's group (dev_type / 16) with STEDMA40_DEV_DST_MEMORY
(-1), the only way we'd obtain a positive result is if we passed -16 as a
device type, which is unfeasible. Instead, it would be much more sane to
compare STEDMA40_DEV_DST_MEMORY against the raw dev_type in order to expect
the expected result.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are only two default memcpy configurations used for the DMA40
driver; one for physical memcpy and one for logical memcpy. Instead
of invariably passing the same configurations though platform data,
we're moving them into the driver instead.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit
"dmaengine: ste_dma40: Assign memcpy channels in the driver"
had two problems:
- It assigned magic numbers to the memcpy event lines
instead of giving them symbolic names.
- It seems to have missed one of the memcpy event lines,
number 51.
This patch fixes it up.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The channels reserved for memcpy are the same for all currently
supported platforms. With this in mind, we can ease the platform
data passing requirement by moving these assignments out from
platform code and place them directly into the driver.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code I added in "mac80211: don't start new netdev queues
if driver stopped" crashes for monitor and AP VLAN interfaces
because while they have a netdev, they don't have queues set
up by the driver.
To fix the crash, exclude these from queue accounting here
and just start their netdev queues unconditionally.
For monitor, this is the best we can do, as we can redirect
frames there to any other interface and don't know which one
that will since it can be different for each frame.
For AP VLAN interfaces, we can do better later and actually
properly track the queue status. Not doing this is really a
separate bug though.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We copy the result to user if the command is completed from the
controller even if it completes with failure (non-zero) status.
A return status of < 0 indicates the command was not completed
by the controller. The user application may expect the error code
in the result field in case of failure.
Signed-off-by: Chayan Biswas <Chayan.Biswas@sandisk.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
