This patch adds device tree node for PWM block present on Exynos 4 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch removes legacy PWM timer interrupt initialization from
exynos{4,5}_init_irq() functions, since it conflicts with internal
interrupt handling of the new PWM clocksource driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Due to rounding errors in clockevents core (in conversions between ticks
and nsecs), it might happen that the set_next_event callback gets called
with cycles = 0, causing the code to incorrectly program the PWM timer.
This patch modifies the callback to program the timer for 1 tick, if
received tick count value is 0.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
In current code, the tick count value programmed to the hardware is
always decremented by one. This is reasonable for periodic mode, since
there is one extra tick between 0 and COUNT (after reloading), but it
makes oneshot events happen 1 tick earlier than requested, because the
interrupt is triggered on transition from 1 to 0.
This patch removes the decrementation from PWM channel setup code and
moves it instead to periodic timer setup, to make both periodic and
oneshot modes work correctly.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch replaces hardcoded -1 argument passed to
clockevents_config_and_register() with tcnt_max calculated based on
variant data.
This fixes invalid max delta configuration for 16-bit timers of s3c24xx.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch extends the driver to support platforms that still use legacy
ATAGS-based boot, without device tree, by providing an exported function
that can be used from platform code to initialize the clocksource.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch removes the unused samsung_pwm struct from public header.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch modifies the driver to keep all its private data consistently
in a single struct, instead of keeping part as separate variables.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch makes the PWM spinlock global and exports it to allow using
it in Samsung PWM driver (will be reworked to use proper synchronization
in further patches).
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch modifies the way of enabling the driver to let the platforms
select it in their Kconfig instead of specifying particular platforms in
Kconfig entry of the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds missing documentation describing Device Tree bindings
for Samsung PWM timers.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add basic EC information to device tree, currently only describing the
keyboard and keymap.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that we have i2c-arbitrator in place on bus 4 we can add the
sbs-battery driver. Future devices will be added onto bus 4 once
drivers are in good shape.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
We need to use the i2c-arbitrator to talk to any of the devices on i2c
bus 4 on exynos5250-snow so that we don't confuse the embedded
controller (EC). Add the i2c-arbitrator to the device tree. As we
add future devices (keyboard, sbs, tps65090) we'll add them on top of
this.
The arbitrated bus is numbered 104 simply as a convenience to make it
easier for people poking around to guess that it might have something
to do with the physical bus 4.
The addition is split between the cros5250-common and the snow device
tree file since not all cros5250-class devices use arbitration.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* exynos/dt: (125 commits)
ARM: dts: add PDMA0 changes for exynos5440
ARM: dts: Add cpufreq controller node for Exynos5440 SoC
ARM: dts: Fix gmac clock ids due to changes in Exynos5440
ARM: dts: add device tree file for SD5v1 board
ARM: dts: update bootargs to boot from sda2 for exynos5440-ssdk5440
ARM: dts: add PMU support in exynos5440
ARM: dts: Add node for GMAC for exynos5440
ARM: dts: list the interrupts generated by pin-controller on Exynos5440
ARM: dts: Add FIMD DT binding Documentation
ARM: dts: Add FIMD node and display timing node to exynos4412-origen.dts
ARM: dts: Add FIMD node to exynos4
ARM: dts: Add SYSREG block node for S5P/Exynos4 SoC series
ARM: dts: Add display timing node to exynos5250-smdk5250.dts
ARM: dts: Add FIMD node to exynos5
ARM: dts: Add virtual GIC DT bindings for exynos5440
ARM: dts: Document usb clocks in samsung,exynos4210-ehci/ohci bindings
ARM: dts: add usb 2.0 clock references to exynos5250 device tree
ARM: dts: Add architected timer nodes for exynos5250
ARM: dts: Declare the gic as a15 compatible for exynos5250
ARM: dts: Add HDMI HPD and regulator node for Arndale board
...
* samsung/pinctrl-exynos:
ARM: EXYNOS: skip wakeup interrupt registration for exynos5250 if pinctrl is enabled
gpio: samsung: skip gpiolib registration if pinctrl support is enabled for exynos5250
pinctrl: exynos: add exynos5250 SoC specific data
Along the time, several debug messages were added at cx88-cards.
While those are still useful to track some troubles with
tuners, they're too verbose:
[ 5768.281801] cx88[0]: Calling XC2028/3028 callback
[ 5768.287388] cx88[0]: Calling XC2028/3028 callback
[ 5768.292575] cx88[0]: Calling XC2028/3028 callback
[ 5768.299408] cx88[0]: Calling XC2028/3028 callback
[ 5768.306244] cx88[0]: Calling XC2028/3028 callback
...
and, most of the time, useless.
So, disable them, except if core_debug modprobe parameter
is used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While a nested run is pending, vmx_queue_exception is only called to
requeue exceptions that were previously picked up via
vmx_cancel_injection. Therefore, we must not check for PF interception
by L1, possibly causing a bogus nested vmexit.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
KVM guests today use 8bit APIC ids allowing for 256 ID's. Reserving one
ID for Broadcast interrupts should leave 255 ID's. In case of KVM there
is no need for reserving another ID for IO-APIC so the hard max limit for
VCPUS can be increased from 254 to 255. (This was confirmed by Gleb Natapov
http://article.gmane.org/gmane.comp.emulators.kvm.devel/99713 )
Signed-off-by: Chegu Vinod <chegu_vinod@hp.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
We hope to at some point deprecate KVM legacy device assignment in
favor of VFIO-based assignment. Towards that end, allow legacy
device assignment to be deconfigured.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The VMX implementation of enable_irq_window raised
KVM_REQ_IMMEDIATE_EXIT after we checked it in vcpu_enter_guest. This
caused infinite loops on vmentry. Fix it by letting enable_irq_window
signal the need for an immediate exit via its return value and drop
KVM_REQ_IMMEDIATE_EXIT.
This issue only affects nested VMX scenarios.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
It is "exit_int_info". It is actually EXITINTINFO in the official docs
but we don't like screaming docs.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
currently apparmor name parsing is only correctly handling
:<NS>:<profile>
but
:<NS>://<profile>
is also a valid form and what is exported to userspace.
Signed-off-by: John Johansen <john.johansen@canonical.com>
the exec file isn't processing its command arg. It should only set be
responding to a command of exec.
Also cleanup setprocattr some more while we are at it.
Signed-off-by: John Johansen <john.johansen@canonical.com>
smatch reports
error: potential NULL dereference 'ns'.
this can not actually occur because it relies on aa_split_fqname setting
both ns_name and name as null but ns_name will actually always have a
value in this case.
so remove the unnecessary if (ns_name) conditional that is resulting
in the false positive further down.
Signed-off-by: John Johansen <john.johansen@canonical.com>
The audit type table is missing a comma so that KILLED comes out as
KILLEDAUTO.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Steve Beattie <sbeattie@ubuntu.com>
The top 8 bits of the base field have never been used, in fact can't
be used, by the current 'dfa16' format. However they will be used in the
future as flags, so mask them off when using base as an index value.
Note: the use of the top 8 bits, without masking is trapped by the verify
checks that base entries are within the size bounds.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Kees Cook <kees@ubuntu.com>
Move the free_profile fn ahead of aa_alloc_profile so it can be used
in aa_alloc_profile without a forward declaration.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Kees Cook <kees@ubuntu.com>
The sid is not going to be a direct property of a profile anymore, instead
it will be directly related to the label, and the profile will pickup
a label back reference.
For null-profiles replace the use of sid with a per namespace unique
id.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Kees Cook <kees@ubuntu.com>
Instead of limiting the setting of the processes limits to current,
relax this to tasks confined by the same profile, as the apparmor
controls for rlimits are at a profile level granularity.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Steve Beattie <sbeattie@ubuntu.com>
The "permipc" command is unused and unfinished, remove it.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Kees Cook <kees@ubuntu.com>
-ESTALE used to be incorrectly used to indicate a disconnected path, when
name lookup failed. This was fixed in commit e1b0e444 to correctly return
-EACCESS, but the error to failure message mapping was not correctly updated
to reflect this change.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-by: Steve Beattie <sbeattie@ubuntu.com>
When policy specifies a transition to a profile that is not currently
loaded, it result in exec being denied. However the failure is not being
audited correctly because the audit code is treating this as an allowed
permission and thus not reporting it.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Acked-By: Steve Beattie <sbeattie@ubuntu.com>
This is primarily useful when there's a driver that doesn't claim clocks
properly, but the bootloader leaves them on. It's not expected to be used
in normal cases, but for bringup and debug it's very useful to have the
option to not gate unclaimed clocks that are still on.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed up trivial merge issue]
Reported by Fengguang's kbuild test robot:
kernel/cpuset.c:787: warning: 'generate_sched_domains' defined but not used
Introduced by commit e0e80a02e5
("cpuset: use rebuild_sched_domains() in cpuset_hotplug_workfn()),
which removed generate_sched_domains() from cpuset_hotplug_workfn().
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since we will remove items off the list using list_del_init() we need
to use a safe version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
