Commit edc7cb2 (usb: phy: make it a menuconfig) makes USB_MXS_PHY
be a sub-item of menuconfig symbol USB_PHY. This change gets the
selection of CONFIG_USB_MXS_PHY in imx_v6_v7_defconfig lost. Hence the
boot stops at the point below.
ci_hdrc ci_hdrc.0: doesn't support gadget
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
Add CONFIG_USB_PHY to have the CONFIG_USB_MXS_PHY selection back to
work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The symbol usb_bind_phy is exported and annotated __init.
It looks like section mismatch. Fix by removing the
__init annotation of usb_bind_phy.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If function instances are not put on gadget's unbind, their implementation
module's refcount is nonzero and it is impossible to unload them.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
acm was the first function to be converted and it seems that its
code served as a base for converting f_sourcesink to the new function
interface. source_sink has nothing to do with acm, though.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Introduced by commit 29a664 (usb: gadget: cdc2: use function
framework for ACM)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Introduced by commit 59835a (usb: gadget: multi: use
function framework for ACM.)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently we have a special code in tps80031_ldo_set_voltage_sel() to handle
LDO2 track mode for TPS80031 or TPS80032-ES1.0. The purpose is to address below
issues:
Issue description:
- LDO2 traking mode is enabled
- LDO2 tracks SMPS2 voltage.
- LDO2 automatically switch-off when LDO2_CFG_VOLTAGE is changed to some discrete values (non exhaustive list):
00011001, 00011010, 00011011, 00011100, .
- LDO2 switch-on again when LDO2_CFG_VOLTAGE is changed to other values (non exhaustive list):
00011000, 00010111, .
LDOs have reserved codes. For these codes, LDO is switch-off.
In tracking, LDO2 ref comes from SMPS2.
However LDO2 enable is still gated by LDO2 VSEL decoding.
As a result, in tracking mode LDO2 will be disabled for following code (SMPS VSEL format):
000000 & 100000 (MSB not decoded)
011001 & 111001 (MSB not decoded)
011010 & 111010 (MSB not decoded)
011100 & 111100 (MSB not decoded)
011101 & 111101 (MSB not decoded)
011110 & 111110 (MSB not decoded)
However, current code has below bugs:
1. It uses regulator_list_voltage_linear, so list_voltage() still shows above
invalid selectors have supported voltage.
2. Current code may return -EINVAL in tps80031_ldo_set_voltage_sel() for
supported voltage. This is because when we use regulator_list_voltage_linear
as list_voltage callback, regulator core will default use
regulator_map_voltage_linear(). regulator_map_voltage_linear() has an
assumption that the voltages are linear which is not true for this case.
For example,
when request voltage range is: min_uV=950000 uV && max_uV=1200000 uV
regulator_map_voltage_linear() returns the selector is 29 (0x1D),
set_voltage_sel() returns -EINVAL.
(The selector is in invalid range, 0x19 ~ 0x1f).
In above case, map_voltage() should find the lowest valid voltage within
specific range (selector = 0x20) and set_voltage_sel() should successfully
set the voltage to 987500 uV.
This patch fixes these issues by:
1. Add checking valid setting for LDO2 track mode of TPS80031 or TPS80032-ES1.0
in list_voltage. So it returns -EINVAL for invalid selectors.
2. Implement tps80031_ldo_map_voltage, use regulator_map_voltage_iterate()
to find the lowest voltage within specific range for TPS80031 or
TPS80032-ES1.0. This is required when the voltage map is no longer linear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drivers use cmpxchg64, cmpxchg64_local to perform 64-bit operation, so
they can cross 32-bit and 64-bit platforms (it is a standard way).
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
All regulators have ascendant voltage list in this driver.
Thus use regulator_map_voltage_ascend is more efficient than the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All regulators have ascendant voltage list in this driver.
Some regulators have more than 200 supported voltages.
e.g.
For TPS65910_REG_VDD1 and TPS65910_REG_VDD2:
n_voltages = VDD1_2_NUM_VOLT_FINE * VDD1_2_NUM_VOLT_COARSE
= 73 * 3
= 219
Thus it worth converting to regulator_map_voltage_ascend rather than use
default regulator_map_voltage_iterate.
For consistent, convert all regulators to regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All regulators have ascendant voltage list in this driver.
Thus use regulator_map_voltage_ascend is more efficient than the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All regulators have ascendant voltage list in this driver.
Thus use regulator_map_voltage_ascend is more efficient than the default
regulator_map_voltage_iterate.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
dma_request_slave_channel() is a more appropriate API for dmaengine
clients that adopt generic DMA bindings to call. Let's use it instead
of of_dma_request_slave_channel() to save <linux/of_dma.h> include.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The examples in Documentation/devicetree/bindings/dma/dma.txt recommends
the name for dma channel doing both RX and TX to be "rx-tx". This
becomes a common pattern that has been adopted by platforms that
converts to generic DMA bindings. Let's follow this common pattern in
generic-dmaengine-pcm.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simply the [get|set]_voltage_sel implementation by using
regulator_[set|get]_voltage_sel_regmap instead of open coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All radio ops are 16b (there is only 1 exception for reg 0x1), so we
deprecated b43_radio_read16 and b43_radio_write16 long time ago.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
In MMIO dumps of ndiswrapper there are following PHY ops:
phy_read(0x0118) -> 0x013d
phy_read(0x01ed) -> 0x993d
phy_read(0x0119) -> 0x012f
phy_read(0x01ee) -> 0x992f
phy_read(0x011a) -> 0x0139
phy_read(0x0969) -> 0x9939
It matches the code of wlc_phy_txpower_est_power_nphy (from brcm80211),
so we know the registers meaning.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
After b43_phy_ht_tx_power_ctl_setup there are some extra radio ops:
radio_read(0x08bf) -> 0x0001
radio_write(0x08bf) <- 0x0001
radio_write(0x0159) <- 0x0011
On N-PHY we write 0x11 to TSSI regs, so it's probably sth similar.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Now when we know many radio regs at 0x000 are core-generic, I've noticed
we duplicate some values in the tables.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
After comparing writes to registers at 0x000, 0x400 and 0x800 it seems
there are many very similar writes. So 0x000 offset is not for accessing
something totally different, but probably just the first out of three
cores.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
According to the datasheet[1]
Register 0x06h Description: RmpCtrl (REGISTER ADDRESS: 0x06h Read/Write)
BIT[5..7]:
RMP[2:0] Output voltage ramp timing
D7-D5 Slope
000 32mV/us
001 16mV/us
010 8mV/us
...
110 0.5mV/us
111 0.25mV/us
Thus to get correct ramp_ctrl value, we need to right-shift 5 bits.
[1] http://www.ti.com/lit/ds/symlink/tps62360.pdf
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add tracepoints to debug the various page write operation
like data pages, meta pages.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
[Jaegeuk: remove unnecessary tracepoints]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add tracepoints for tracing the garbage collector
threads in f2fs with status of collection & type.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
[Jaegeuk: modify slightly to show information]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We need to hold the rps lock around punit access.
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
lpc32xx_pwm_config() is supposed to set duty_ns and period_ns,
it should not change PWM_ENABLE bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
According to the LPC32x0 User Manual [1]:
For both PWM1 and PWM2 Control Registers:
BIT 31:
This bit gates the PWM_CLK signal and enables the external output pin
to the PWM_PIN_STATE logical level.
0 = PWM disabled. (Default)
1 = PWM enabled
So in lpc32xx_pwm_enable(), we should set PWM_ENABLE bit.
In lpc32xx_pwm_disable(), we should just clear PWM_ENABLE bit rather than
write 0 to the register which will also clear PWMx_RELOADV and PWMx_DUTY bits.
[1] http://www.nxp.com/documents/user_manual/UM10326.pdf
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Kay Sievers reported that coreutils' stat tool has a problem with
s390's statfs[64] definition:
> The definition of struct statfs::f_type needs a fix. s390 is the only
> architecture in the kernel that uses an int and expects magic
> constants lager than INT_MAX to fit into.
>
> A fix is needed to make Fedora boot on s390, it currently fails to do
> so. Userspace does not want to add code to paper-over this issue.
[...]
> Even coreutils cannot handle it:
> #define RAMFS_MAGIC 0x858458f6
> # stat -f -c%t /
> ffffffff858458f6
>
> #define BTRFS_SUPER_MAGIC 0x9123683E
> # stat -f -c%t /mnt
> ffffffff9123683e
The bug is caused by an implicit sign extension within the stat tool:
out_uint_x (pformat, prefix_len, statfsbuf->f_type);
where the format finally will be "%lx".
A similar problem can be found in the 'tail' tool.
s390 is the only architecture which has an int type f_type member in
struct statfs[64]. Other architectures have either unsigned ints or
long values, so that the problem doesn't occur there.
Therefore change the type of the f_type member to unsigned int, so
that we get zero extension instead of sign extension when assignment to
a long value happens.
This patch changes the s390 uapi struct stafs[64] definition in the kernel
to contain only unsigned values.
This was true for 32 bit builds anyway, since we use the generic uapi
header file in that case. So lets not include conditionally the generic
uapi header file but have the s390 implementation completely independent.
Also fix the types of struct compat_stafs to match reality and move the
definition of struct compat_statfs64 to asm/compat.h since it is not part
of the api.
Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For offset > PAGE_SIZE, s390_dma_map_pages() will issue a warning
and return a wrong dma address.
This patch removes the warning and fixes the dma return address
calculation.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The compat definitions are not part of the uapi. So move them to
s390's private compat header file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
