This patch allows iscsiadm to manage iSCSI target information stored on
adapter flash on per host basis.
The sysfs entries will look as cited below:
/sys/bus/iscsi_flashnode/devices/flashnode_sess-<host_no>:<flashnode_id>/<session attrs>
/sys/bus/iscsi_flashnode/devices/flashnode_conn-<host_no>:<flashnode_id>:<conn_id>/<conn attrs>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If a TCP retransmission gets partially ACKed and collapsed multiple
times it is possible for the headroom to grow beyond 64K which will
overflow the 16bit skb->csum_start which is based on the start of
the headroom. It has been observed rarely in the wild with IPoIB due
to the 64K MTU.
Verify if the acking and collapsing resulted in a headroom exceeding
what csum_start can cover and reallocate the headroom if so.
A big thank you to Jim Foraker <foraker1@llnl.gov> and the team at
LLNL for helping out with the investigation and testing.
Reported-by: Jim Foraker <foraker1@llnl.gov>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While probe Skip retry of initialize_adapter only for ISP82XX and ISP83XX.
We need to retry initialize_adapter for ISP40XX.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
If flash read for FLT fails, we are assigning wrong default
address for CHAP table in FLT, which will cause CHAP table
read/write to wrong address.
Fix:
Assign correct default CHAP table address to FLT.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The definitions have moved to include/linux/usb/samsung-usb-phy.h,
and plat/usb-phy.h is unavailable from drivers in a multiplatform
configuration.
Also fix up the plat/usb-phy.h header file to use the definitions
from the new header instead of providing a separate copy.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading the cpu speed, round it to the closest available
frequency from the table.
Signed-off-by: Mats Fagerstrom <mats.fagerstrom@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dereference to 'put_index' should be moved below the NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make a copy of the IDT (as seen via the "sidt" instruction) read-only.
This primarily removes the IDT from being a target for arbitrary memory
write attacks, and has the added benefit of also not leaking the kernel
base offset, if it has been relocated.
We already did this on vendor == Intel and family == 5 because of the
F0 0F bug -- regardless of if a particular CPU had the F0 0F bug or
not. Since the workaround was so cheap, there simply was no reason to
be very specific. This patch extends the readonly alias to all CPUs,
but does not activate the #PF to #UD conversion code needed to deliver
the proper exception in the F0 0F case except on Intel family 5
processors.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130410192422.GA17344@www.outflux.net
Cc: Eric Northup <digitaleric@google.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
__cpufreq_governor() must be called with a correct policy->cpus mask.
In __cpufreq_remove_dev() we initially clear policy->cpus with
cpumask_clear_cpu() and then call
__cpufreq_governor(policy, CPUFREQ_GOV_POLICY_EXIT). If the governor
is doing some per-cpu stuff in EXIT callback, this can create
uncertain behavior.
Generic governors in drivers/cpufreq/ doesn't do any per-cpu stuff
in EXIT callback and so we don't face any issues currently. But its
better to keep the code clean, so we don't face any issues in future.
Now, we call cpumask_clear_cpu() only when multiple cpus are managed
by policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 18a3870 (ACPI / PM: Expose lists of device power resources
to user space) exposed the lists of ACPI power resources associated
with power states of ACPI devices, but it didn't expose the lists
of ACPI wakeup power resources, which also is necessary to get the
full picture of dependencies between ACPI devices and power
resources.
For this reason, for every ACPI device node having a list of ACPI
wakeup power resources associated with it, expose that list to user
space in analogy with commit 18a3870.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Before, it was a function that would set all members of a given struct
containing only int members to -1. Now, it is renamed to
dwc_set_all_params and it works only on the dwc2_core_params struct.
This makes sure that all of the slightly dubious casting and assumptions
happen inside the function instead of by the caller.
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, it was "dwc_otg", but this does not correspond to the
directory name and might cause confusion with the old out-of-tree
dwc_otg driver of which many versions circulate.
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert use of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
This was found with coccinelle.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO support to mv643xx_eth by making it invoke
napi_gro_receive instead of netif_receive_skb.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan_features was zero which prevents vlan GSO packets to be transmitted to
userspace. This is suboptimal so enable this by initialize vlan_features for
tuntap.
Netperf shows better performance of guest receiving since vlan TSO works for
tuntap:
before:
netperf -H 192.168.5.4
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.5.4 ()
port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.01 2786.67
after:
netperf -H 192.168.5.4
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.5.4 ()
port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 8085.49
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's nothing that prevent passing the device features of virtio_net to its
vlan device. So this patch simply passes those to vlan device to benefit from
advanced features.
Netperf shows better sending performance for vlan device since TSO can work on
vlan now.
before:
netperf -H 192.168.5.2
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.5.2 ()
port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 4162.35
after:
netperf -H 192.168.5.2
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.5.2 ()
port 0 AF_INET : demo
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 9365.42
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Designware UART has an optional support for 16750
compatible Auto Flow Control. This will enable it based on
the AFCE bit in Component Parameter Register.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new ACPI DMA helpers in dmaengine API can take care of
extracting all the necessary information regarding DMA. The
driver does not need to do this separately any more.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lynxpoint LPSS peripheral clocks are now handled in clk
framework so the drivers do not need to take care of them
manually. In dw8250_probe_acpi(), the uartclk is now taken
from the driver_data only if it was not already set.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows ACPI to put the device to D3 when it's not used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some slave channel parameters will be always the same. For
example, direction for the Rx channel will always be
DMA_DEV_TO_MEM and DMA_MEM_TO_DEV for Tx channel.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves shared private data kzalloc to managed devm_kzalloc and
cleans now unneccessary kfree and error handling.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an optional shared block clock to avoid lockups on
clock gated controllers. Besides the new clock, clock handling for
existing clocks is cleaned up and moved to devm_clk_get. Device
tree binding documentation is updated for the new clocks property.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3d604da1e9
("net: mvmdio: get and enable optional clock")
was missing an update of the corresponding device tree binding
documentation. This patch adds the clocks property to mvmdio
binding documentation.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper functions in dmaengine API allow the drivers to
request slave channels without the filter parameters. They
will attempt to extract the needed DMA client information
from DT or ACPI, but if such information is not available
the filter parameters can still be used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Overrun, parity and framing errors should be handled in
8250_core. This also adds check for the dma_status and exits
if the channel is not idle.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing one unneeded uart_write_wakeup(). There is no need
to start PIO transfer unless DMA fails, so this also changes
serial8250_tx_dma() to return 0 unless that is the case.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 2b8b328b61 (vhost_net: handle polling
errors when setting backend), we in fact track the polling state through
poll->wqh, so there's no need to duplicate the work with an extra
vhost_net_polling_state. So this patch removes this and make the code simpler.
This patch also removes the all tx starting/stopping code in tx path according
to Michael's suggestion.
Netperf test shows almost the same result in stream test, but gets improvements
on TCP_RR tests (both zerocopy or copy) especially on low load cases.
Tested between multiqueue kvm guest and external host with two direct
connected 82599s.
zerocopy disabled:
sessions|transaction rates|normalize|
before/after/+improvements
1 | 9510.24/11727.29/+23.3% | 693.54/887.68/+28.0% |
25| 192931.50/241729.87/+25.3% | 2376.80/2771.70/+16.6% |
50| 277634.64/291905.76/+5% | 3118.36/3230.11/+3.6% |
zerocopy enabled:
sessions|transaction rates|normalize|
before/after/+improvements
1 | 7318.33/11929.76/+63.0% | 521.86/843.30/+61.6% |
25| 167264.88/242422.15/+44.9% | 2181.60/2788.16/+27.8% |
50| 272181.02/294347.04/+8.1% | 3071.56/3257.85/+6.1% |
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few bugs in the samsung serial driver when built as a
loadable module, which makes the console code unavailable, as well as
giving no access to the 'printascii' early debug function. This adds
the appropriate compile time conditionals.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steffen Klassert says:
====================
1) Allow to avoid copying DSCP during encapsulation
by setting a SA flag. From Nicolas Dichtel.
2) Constify the netlink dispatch table, no need to modify it
at runtime. From Mathias Krause.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The registers for the Samsung S3C serial port are currently defined in
the platform specific arch/arm/plat-samsung/include/plat/regs-serial.h
file, which is not visible to multiplatform capable drivers.
Unfortunately, it is not possible to move the file into a more local
place as we should normally try to, because the same registers
may be used in one of four places:
* In the driver itself
* In platform-independent ARM code for early debug output
* In platform_data definitions
* In the Samsung platform power management code
I have also found no way to logically split out a platform_data
file, other than possibly move everything into
include/linux/platform_data, which also felt wrong. The only
part of this file that makes sense to keep specific to the s3c24xx
platform are the virtual and physical addresses defined here,
which are needed in no other location.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the common clock interface, there is no way to provide the
"clock_source" sysfs attribute for the samsung serial ports. Given that
this file was purely informational and had fixed contents, we have reason
to believe that no user space programs were relying on it.
The sysfs file is not documented in the ABI docs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting MTU in SRIOV mode add ETH, VLAN and FCS header length
to the maximum MTU obtained from QUERY_DEV_CAP.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different steering modes are global to the device, with DMFS
being introduced after SRIOV was merged. Hence, SRIOV guests running
legacy / older Linux kernels or non-Linux drivers may provide
B0 steering directives when the hypervisor is using DMFS and fail.
Under B0 only L2 steering rules are allowed, hence B0 is a subset of DMFS.
Use this fact to enable such legacy guests to run by modifying the SRIOV
B0 steering wrapper to translate guest B0 directives to DMFS ones when
the device uses DMFS. The translated B0 rule has to be kept in the
resource tracker as a B0 object to allow for lookup in case of detach.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pre-step for supporting guests that use B0 steering over a hypervisor
that runs in DMFS (device managed flow steering mode). Add helper function
which allows to translate L2 attachments / detachments provided in B0 mode
to DMFS rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sp804 binding is already in use by several platforms. This adds missing
documentation for the binding and also extends the binding to handle some
additional possible interrupt configurations.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Move the integrator-cp timer init to timer-sp.c and use CLKSRC_OF. There is
no reason to use the aliases, so drop them from the init code.
The integrator-cp timers are mistakenly called sp804 timers in the dts, but
in fact they are not sp804 dual timers, but single timers with the same
programming model. Fix the dts to reflect this.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The timer-sp initialization code clears the control register before
initializing the timers, so every platform doing this is redundant.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The motherboard sp804 timer is used, but core tile sp804 timer is not.
According to Russell King, the clock configuration is undocumented and
defaults to 32kHz which is not desireable. So mark core tile sp804 timer
as disabled.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Remove the vexpress specific setup for the sp804 timer now that
clocksource_of_init will do it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
This adds CLKSRC_OF based init for sp804 timer. The clock initialization is
refactored to support retrieving the clock(s) from the DT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This converts arm and arm64 to use CLKSRC_OF DT based initialization for
the arch timer. A new function arch_timer_arch_init is added to allow for
arch specific setup.
This has a side effect of enabling sched_clock on omap5 and exynos5. There
should not be any reason not to use the arch timers for sched_clock.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
