Commit graph

388,156 commits

Author SHA1 Message Date
Wang YanQing
8b5c913f7e serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection
The code in 8250.c for detecting ARM/XScale UARTs says:

  * Try writing and reading the UART_IER_UUE bit (b6).
  * If it works, this is probably one of the Xscale platform's
  * internal UARTs.

If the above passes, it then goes on to:

     * It's an Xscale.
     * We'll leave the UART_IER_UUE bit set to 1 (enabled).

However, the CH352 uses the UART_IER_UUE as the LOWPOWER function,
so it is readable and writable.  According to the datasheet:

    "LOWPOWER:When the bit is 1, close the internal benchmark
     clock of serial port to set into low-power status.

So it essentially gets mis-detected as Xscale, and gets
powered down in the process.  The device in question where
this was seen is listed by lspci as:

 Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550])

Re-using the 353 quirk which just sets flags to fixed and type
to 16550 is suitable for fixing the 352 as well.

Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 13:27:35 -07:00
Pawel Wieczorkiewicz
503bded92d tty: atmel_serial_probe(): index of atmel_ports[] fix
Index of atmel_ports[ATMEL_MAX_UART] should be smaller
than ATMEL_MAX_UART.

Signed-off-by: Pawel Wieczorkiewicz <wpawel@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 13:23:29 -07:00
Peter Hurley
19ffd68f81 pty: Remove redundant itty reset
port->itty has already been reset by release_tty() before
pty_cleanup() is called.

Call stack:
release_tty()
  tty_kref_put()
    queue_release_one_tty()
      release_one_tty() : workqueue
        tty->ops->cleanup()
          pty_cleanup()

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 13:00:48 -07:00
Andy King
347e0899b1 VMCI: Fix process-to-process DRGAMs.
When sending between processes, we always schedule a work item.  Our work info
struct has the message embedded in the middle, which means that we end up
overwriting subsequent fields when we copy the (variable-length) message into
it.  Move it to the end of the struct.

Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:58:12 -07:00
Greg Kroah-Hartman
61ec7e77d7 extcon fixes for 3.9-rc3
This is small fixes against 3.9-rc2.
 
 Fix to max77693 extcon driver:
 - Set default value of MUIC register to bring up it.
 Fix to max8997 extcon driver:
 - Fix null pointer error duing probe when platform data
 isn't used.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJRQDzoAAoJEJzN3yze689TprQP+gPvd2I2LLl/Sq42UyhtzIlk
 MlDIXk/4mHLeDycsTEq6RlDHmA2mXznpnXd0lyIBrD4VJqie9RQsd2TMJ560QeBd
 PJPaQwruAcKnRBh6BdVRNGE9wZvZYEaXOl6tB0QHbldrqfA6lU3WzOd4lzw7dnNw
 a+nFkhvLUraIHAlvjGMlH5ZEhobuKpsOyWSpznI1M5MsvxgPoEL4Vzbq5/QJBVVD
 R5x9tZ+Fb0PM1IexwDpBzxuTMGua0XJsrKCZ3FZExy5LcIb1etnELmacwPNkr0XX
 N06ZwJyQWiG4TpRvYOhhpWbhHwlGLu2tTtfvg+TipeN+bjFarExeg7IiReNiz2Sg
 mig+5R8BMAXMMcaC7l1erzaOPrUJDrBdd57pBGCx3eYIW1OeHJ1apTKKKaFXTqdr
 w19Y4j379breQMIk41KaFhZcWidgt37qxxKpreaM8XowJBhrrFFUSOvDTWhCBxq6
 AUIWtP5kCUPynivkpm7S6f0N2nSdtRVQTpVGUwORxPCt3tMXErWDC2Hd+8GTioXC
 9i3pFmbOHB60WEaTIr1wHFWCX+vnU8pWk6TPt/NSF9vScZxKUnNw0inOv/fsqyVM
 D8vTNYrjyq9ES21jmmIcYCtS1Ue7D+aj0t6f0YNxrsslaq/k5AKMI2xtg+q4HPTI
 lhCd46ALukPKHIxs1oc+
 =XVHH
 -----END PGP SIGNATURE-----

Merge tag 'extcon-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-linus

Chanwoo writes:

	extcon fixes for 3.9-rc3

	This is small fixes against 3.9-rc2.

	Fix to max77693 extcon driver:
	- Set default value of MUIC register to bring up it.
	  Fix to max8997 extcon driver:
	- Fix null pointer error duing probe when platform data
	  isn't used.
2013-03-15 12:56:11 -07:00
Kurt Van Dijck
a750fa4edd softingcs: use module_pcmcia_driver
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:30:15 -07:00
Kurt Van Dijck
7fced565e5 softingcs: initialize spinlock with macro
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:29:00 -07:00
H Hartley Sweeten
fdd3f29edd drivers/net: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:27:33 -07:00
H Hartley Sweeten
b85c4a18f6 sound/pcmcia: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:39 -07:00
H Hartley Sweeten
4c7a45fb1b drivers/usb: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:38 -07:00
H Hartley Sweeten
5339102c77 drivers/tty: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:38 -07:00
H Hartley Sweeten
3e13ea450b drivers/scsi: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:38 -07:00
H Hartley Sweeten
f23e79688c drivers/parport: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:38 -07:00
H Hartley Sweeten
fe141149bf drivers/mmc: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:04 -07:00
H Hartley Sweeten
0aae9c6a91 drivers/isdn: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:04 -07:00
H Hartley Sweeten
e0c005f4b9 drivers/bluetooth: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:04 -07:00
H Hartley Sweeten
460604850a drivers/ata: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:03 -07:00
H Hartley Sweeten
6ed7ffddcf pcmcia/ds.h: introduce helper for pcmcia_driver module boilerplate
Introduce the module_pcmcia_driver() macro which is a convenience macro
for pcmcia driver modules. It is intended to be used by pcmcia drivers
with init/exit sections that do nothing but register/unregister the
pcmcia driver.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: linux-pcmcia@lists.infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:26:03 -07:00
Fabio Porcedda
e7c2199ff3 drivers: char: use module_platform_driver_probe()
This patch converts the drivers to use the
module_platform_driver_probe() macro which makes the code smaller and
a bit simpler.

Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:24:20 -07:00
Dan Carpenter
2154e0a4f4 applicom: use correct array offset
We're iterating through abps[] printing information, but here we
use the wrong array index.  IndexCard comes from the user and in
this case it was specifically not range checked because we didn't
expect to use it.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:23:48 -07:00
Samuel Iglesias Gonsalvez
e926301b39 ipack: split ipack_device_register() in several functions
One function is ipack_device_init(). If it fails, the caller should execute
ipack_put_device().

The second function is ipack_device_add that only adds the device. If
it fails, the caller should execute ipack_put_device().

Then the device is removed with refcount = 0, as device_register() kernel
documentation says.

ipack_device_del() is added to remove the device.

Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:23:09 -07:00
Samuel Iglesias Gonsalvez
fa882867ae ipack: add ipack_get_device() ipack_put_device()
Prepare everything for later use.

Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:23:09 -07:00
Hiroshi Doyu
d4cba7fa7e memory: tegra30: Fix build error w/o PM
Make this depend on CONFIG_PM.

Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-03-15 13:22:13 -06:00
Jean-Francois Dagenais
1116575d91 w1: ds2408: use ARRAY_SIZE instead of hard-coded number
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:15:02 -07:00
Jean-Francois Dagenais
aceca28544 w1: ds2408: make value read-back check a Kconfig option
De-activating this reading back will effectively half the time required
for a write to the output register.

Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:15:02 -07:00
K. Y. Srinivasan
96dd86fa58 Drivers: hv: Add a new driver to support host initiated backup
This driver supports host initiated backup of the guest. On Windows guests,
the host can generate application consistent backups using the Windows VSS
framework. On Linux, we ensure that the backup will be file system consistent.
This driver allows the host to initiate a  "Freeze" operation on all the mounted
file systems in the guest. Once the mounted file systems in the guest are frozen,
the host snapshots the guest's file systems. Once this is done, the guest's file
systems are "thawed".

This driver has a user-level component (daemon) that invokes the appropriate
operation on all the mounted file systems in response to the requests from
the host. The duration for which the guest is frozen is very short - a few seconds.
During this interval, the diff disk is comitted.

In this version of the patch I have addressed the feedback from Olaf Herring.
Also, some of the connector related issues have been fixed.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:12:36 -07:00
K. Y. Srinivasan
c87059793d Drivers: hv: vmbus: Handle channel rescind message correctly
Properly cleanup the channel state on receipt of the "offer rescind" message.
Starting with ws2012, the host requires that the channel "relid" be properly
cleaned up when the offer is rescinded.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:11:51 -07:00
K. Y. Srinivasan
1cac8cd4d1 Drivers: hv: balloon: Implement hot-add functionality
Implement the memory hot-add functionality. With this, Linux guests can fully
participate in the Dynamic Memory protocol implemented in the Windows hosts.

In this version of the patch, based Olaf Herring's feedback, I have gotten
rid of the module level dependency on MEMORY_HOTPLUG. Instead the code within
the driver that depends on MEMORY_HOTPLUG has the appropriate compilation
switches. This would allow this driver to support pure ballooning in cases
where the kernel does not support memory hotplug.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:11:51 -07:00
K. Y. Srinivasan
0cf40a3e66 Drivers: hv: balloon: Make the balloon driver not unloadable
The balloon driver is stateful. For instance, it needs to keep track of pages
that have been ballooned out to properly post pressure reports. This state cannot
be re-constructed if the driver were to be unloaded and subsequently loaded.
Furthermore, as we support memory hot-add as part of this driver, this driver becomes
even more stateful and this state cannot be re-created. Make the balloon driver
unloadable to deal with this issue.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:11:50 -07:00
K. Y. Srinivasan
c51af826cf Drivers: hv: balloon: Execute hot-add code in a separate context
Execute the hot-add operation in a separate work context.
This allows us to decouple the pressure reporting activity from the
"hot-add" activity. Testing has shown that this makes the guest more
responsive to hot add requests.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:11:50 -07:00
K. Y. Srinivasan
6571b2dab4 Drivers: hv: balloon: Execute balloon inflation in a separate context
Execute the balloon inflation operation in a separate work context.
This allows us to decouple the pressure reporting activity from the
ballooning activity. Testing has shown that this decoupling makes the
guest more reponsive.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:11:50 -07:00
K. Y. Srinivasan
7a64b864a0 Drivers: hv: balloon: Do not request completion notification
There is no need to request completion notification; get rid of it.

Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:11:50 -07:00
Alan Stern
2a40f32454 USB: EHCI: fix regression during bus resume
This patch (as1663) fixes a regression caused by commit
6e0c3339a6 (USB: EHCI: unlink one async
QH at a time).  In order to avoid keeping multiple QHs in an unusable
intermediate state, that commit changed unlink_empty_async() so that
it unlinks only one empty QH at a time.

However, when the EHCI root hub is suspended, _all_ async QHs need to
be unlinked.  ehci_bus_suspend() used to do this by calling
unlink_empty_async(), but now this only unlinks one of the QHs, not
all of them.

The symptom is that when the root hub is resumed, USB communications
don't work for some period of time.  This is because ehci-hcd doesn't
realize it needs to restart the async schedule; it assumes that
because some QHs are already on the schedule, the schedule must be
running.

The easiest way to fix the problem is add a new function that unlinks
all the async QHs when the root hub is suspended.

This patch should be applied to all kernels that have the 6e0c3339a6
commit.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Adrian Bassett <adrian.bassett@hotmail.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:07:53 -07:00
Dmitry Artamonow
29f86e6642 usb-storage: add unusual_devs entry for Samsung YP-Z3 mp3 player
Device stucks on filesystem writes, unless following quirk is passed:
  echo 04e8:5136:m > /sys/module/usb_storage/parameters/quirks

Add corresponding entry to unusual_devs.h

Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:07:53 -07:00
Hannes Reinecke
00eed9c814 USB: xhci: correctly enable interrupts
xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.

v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:07:53 -07:00
Arnd Bergmann
25e9789ddd vfio: include <linux/slab.h> for kmalloc
The vfio drivers call kmalloc or kzalloc, but do not
include <linux/slab.h>, which causes build errors on
ARM.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: kvm@vger.kernel.org
2013-03-15 12:58:20 -06:00
Roger Quadros
413fd1e9aa USB: ehci-omap: Get rid of omap_ehci_init()
As it does almost nothing, get rid of omap_ehci_init()
and move the ehci->caps initialization part into probe().

Also remove the outdated TODO list from header.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:54:26 -07:00
Roger Quadros
49f092198f USB: ehci-omap: Fix detection in HSIC mode
Move PHY initialization until after EHCI initialization is
complete, instead of initializing the PHYs first, shutting
them down again, and then initializing them a second time.

This fixes HSIC device detection.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:54:21 -07:00
Roger Quadros
a2f450ca88 USB: ehci-omap: Try to get PHY even if not in PHY mode
Even when not in PHY mode, the USB device on the port (e.g. HUB)
might need resources like RESET which can be modelled as a PHY
device. So try to get the PHY device in any case.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:53:52 -07:00
Roger Quadros
a1ae0affee USB: ehci-omap: Add device tree support and binding information
Allows the OMAP EHCI controller to be specified via device tree.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:47 -07:00
Roger Quadros
5867320dec USB: ohci-omap3: Add device tree support and binding information
Allows the OHCI controller found in OMAP3 and later chips to
be specified via device tree.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:47 -07:00
Roger Quadros
8c3ec38550 USB: ohci-omap3: Get platform resources by index rather than by name
Since there is only one resource per type we don't really need
to use resource name to obtain it. This also also makes it easier
for device tree adaptation.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:46 -07:00
Roger Quadros
3414211b91 USB: ehci-omap: Get platform resources by index rather than by name
Since there is only one resource per type we don't really need
to use resource name to obtain it. This also also makes it easier
for device tree adaptation.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:46 -07:00
Roger Quadros
dfdf9ad92a USB: ehci-omap: Select NOP USB transceiver driver
In PHY mode we need to have the nop-usb-xceiv transceiver
driver to operate, so select it in Kconfig.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:46 -07:00
Roger Quadros
218a214723 USB: ehci-omap: Remove PHY regulator handling code
PHY regulator handling must be done in the PHY driver

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:46 -07:00
Roger Quadros
87425ad363 USB: ehci-omap: Remove PHY reset handling code
Reset GPIO handling for the PHY must be done in the PHY
driver. We use the PHY helpers instead to reset the PHY.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:46 -07:00
Roger Quadros
dcd64063fd USB: ehci-omap: Use PHY APIs to get the PHY device and put it out of suspend
For each port that is in PHY mode we obtain a PHY device using the USB PHY
library and put it out of suspend.

It is up to platform code to associate the PHY to the controller's
port and it is up to the PHY driver to manage the PHY's resources.

Also remove weird spacing around declarations we come across.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:46 -07:00
Roger Quadros
18c2bb1b8c USB: ehci-omap: Use devm_ioremap_resource()
Make use of devm_ioremap_resource() and correct comment.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:46 -07:00
Alan Stern
54a419668b USB: EHCI: split ehci-omap out to a separate driver
This patch (as1645) converts ehci-omap over to the new "ehci-hcd is a
library" approach, so that it can coexist peacefully with other EHCI
platform drivers and can make use of the private area allocated at
the end of struct ehci_hcd.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:45 -07:00
Colin Ian King
a1645eefc8 usb: misc: sisusbvga: Avoid NULL pointer dereference from sisusb
A failed kzalloc() is reported with a dev_err that dereferences the null
sisusb, this will cause a NULL pointer deference error.

Instead, pass dev->dev to the dev_err() rather than &sisusb->sisusb_dev->dev

Smatch analysis:

drivers/usb/misc/sisusbvga/sisusb.c:3087 sisusb_probe() error: potential null
  dereference 'sisusb'.  (kzalloc returns null)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 11:51:01 -07:00