Commit graph

1,215,304 commits

Author SHA1 Message Date
Felix Fietkau
02a894046d wifi: mt76: mt7915: fix capabilities in non-AP mode
Capabilities in vif->bss_conf are only initialized in AP mode.
For other modes, they should be enabled by default, in order to avoid a
mismatch.

Fixes: 885f7af7e5 ("wifi: mt76: mt7915: remove mt7915_mcu_beacon_check_caps()")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-26 11:15:04 +02:00
Krzysztof Kozlowski
2422f74eb9 dt-bindings: pinctrl: qcom,pmic-gpio: document PMC8180 and PMC8180C
Document qcom,pmc8180-gpio and qcom,pmc8180c-gpio compatibles already
used in DTS and in the same binding in allOf:if:then section for
narrowing available GPIOs:

  sc8180x-primus.dtb: pmic@4: gpio@c000:compatible:0: 'qcom,pmc8180c-gpio' is not one of ...

Fixes: 04bed6407e ("dt-bindings: pinctrl: qcom,pmic-gpio: describe gpio-line-names")
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230720083539.73675-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-07-26 11:11:47 +02:00
Konrad Dybcio
63f7c8445f pinctrl: qcom: Introduce SM6115 LPI pinctrl driver
Add support for the pin controller block on SM6115's Low Power Island.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230722-topic-6115_lpasstlmm-v2-2-d4883831a858@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-07-26 11:09:47 +02:00
Konrad Dybcio
ba93d88721 dt-bindings: pinctrl: qcom,sm6115-lpass-lpi: add SM6115 LPASS TLMM
Add bindings for pin controller in SM6115 Low Power Audio SubSystem
LPASS).

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230722-topic-6115_lpasstlmm-v2-1-d4883831a858@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-07-26 11:09:42 +02:00
Tim Crawford
5d36931f0f platform/x86: system76: Handle new KBLED ACPI methods
System76 EC since system76/ec@9ac513128a detects if the keyboard is
white or RGB backlit via `RGBKB-DET#` at run-time instead of being set
at compile-time. As part of this, the brightness of white-only backlit
keyboards was also changed to behave more like the RGB-backlit
keyboards: a value between 0 and 255 instead of a firmware-defined
level.

The EC ACPI methods in coreboot have been updated for this new
functionality only, removing the old behavior.

This should preserve behavior as we roll out new firmware with these
changes included and users update to it.

Link: https://github.com/system76/ec/pull/357
Link: https://review.coreboot.org/c/coreboot/+/76152
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20230719181324.47035-1-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-07-26 11:00:07 +02:00
Rob Herring
b9fe9c9ef9 platform: Explicitly include correct DT includes
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20230714174909.4062739-1-robh@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-07-26 10:58:36 +02:00
Peter Seiderer
2303fae130 net: skbuff: remove unused HAVE_HW_TIME_STAMP feature define
Remove unused HAVE_HW_TIME_STAMP feature define (introduced by
commit ac45f602ee ("net: infrastructure for hardware time stamping").

Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-26 09:55:37 +01:00
Muhammad Husaini Zulkifli
d4a7ce6421 igc: Fix Kernel Panic during ndo_tx_timeout callback
The Xeon validation group has been carrying out some loaded tests
with various HW configurations, and they have seen some transmit
queue time out happening during the test. This will cause the
reset adapter function to be called by igc_tx_timeout().
Similar race conditions may arise when the interface is being brought
down and up in igc_reinit_locked(), an interrupt being generated, and
igc_clean_tx_irq() being called to complete the TX.

When the igc_tx_timeout() function is invoked, this patch will turn
off all TX ring HW queues during igc_down() process. TX ring HW queues
will be activated again during the igc_configure_tx_ring() process
when performing the igc_up() procedure later.

This patch also moved existing igc_disable_tx_ring_hw() to avoid using
forward declaration.

Kernel trace:
[ 7678.747813] ------------[ cut here ]------------
[ 7678.757914] NETDEV WATCHDOG: enp1s0 (igc): transmit queue 2 timed out
[ 7678.770117] WARNING: CPU: 0 PID: 13 at net/sched/sch_generic.c:525 dev_watchdog+0x1ae/0x1f0
[ 7678.784459] Modules linked in: xt_conntrack nft_chain_nat xt_MASQUERADE xt_addrtype nft_compat
nf_tables nfnetlink br_netfilter bridge stp llc overlay dm_mod emrcha(PO) emriio(PO) rktpm(PO)
cegbuf_mod(PO) patch_update(PO) se(PO) sgx_tgts(PO) mktme(PO) keylocker(PO) svtdx(PO) svfs_pci_hotplug(PO)
vtd_mod(PO) davemem(PO) svmabort(PO) svindexio(PO) usbx2(PO) ehci_sched(PO) svheartbeat(PO) ioapic(PO)
sv8259(PO) svintr(PO) lt(PO) pcierootport(PO) enginefw_mod(PO) ata(PO) smbus(PO) spiflash_cdf(PO) arden(PO)
dsa_iax(PO) oobmsm_punit(PO) cpm(PO) svkdb(PO) ebg_pch(PO) pch(PO) sviotargets(PO) svbdf(PO) svmem(PO)
svbios(PO) dram(PO) svtsc(PO) targets(PO) superio(PO) svkernel(PO) cswitch(PO) mcf(PO) pentiumIII_mod(PO)
fs_svfs(PO) mdevdefdb(PO) svfs_os_services(O) ixgbe mdio mdio_devres libphy emeraldrapids_svdefs(PO)
regsupport(O) libnvdimm nls_cp437 snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_intel
snd_intel_dspcfg snd_hda_codec snd_hwdep x86_pkg_temp_thermal snd_hda_core snd_pcm snd_timer isst_if_mbox_pci
[ 7678.784496]  input_leds isst_if_mmio sg snd isst_if_common soundcore wmi button sad9(O) drm fuse backlight
configfs efivarfs ip_tables x_tables vmd sdhci led_class rtl8150 r8152 hid_generic pegasus mmc_block usbhid
mmc_core hid megaraid_sas ixgb igb i2c_algo_bit ice i40e hpsa scsi_transport_sas e1000e e1000 e100 ax88179_178a
usbnet xhci_pci sd_mod xhci_hcd t10_pi crc32c_intel crc64_rocksoft igc crc64 crc_t10dif usbcore
crct10dif_generic ptp crct10dif_common usb_common pps_core
[ 7679.200403] RIP: 0010:dev_watchdog+0x1ae/0x1f0
[ 7679.210201] Code: 28 e9 53 ff ff ff 4c 89 e7 c6 05 06 42 b9 00 01 e8 17 d1 fb ff 44 89 e9 4c
89 e6 48 c7 c7 40 ad fb 81 48 89 c2 e8 52 62 82 ff <0f> 0b e9 72 ff ff ff 65 8b 05 80 7d 7c 7e
89 c0 48 0f a3 05 0a c1
[ 7679.245438] RSP: 0018:ffa00000001f7d90 EFLAGS: 00010282
[ 7679.256021] RAX: 0000000000000000 RBX: ff11000109938440 RCX: 0000000000000000
[ 7679.268710] RDX: ff11000361e26cd8 RSI: ff11000361e1b880 RDI: ff11000361e1b880
[ 7679.281314] RBP: ffa00000001f7da8 R08: ff1100035f8fffe8 R09: 0000000000027ffb
[ 7679.293840] R10: 0000000000001f0a R11: ff1100035f840000 R12: ff11000109938000
[ 7679.306276] R13: 0000000000000002 R14: dead000000000122 R15: ffa00000001f7e18
[ 7679.318648] FS:  0000000000000000(0000) GS:ff11000361e00000(0000) knlGS:0000000000000000
[ 7679.332064] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 7679.342757] CR2: 00007ffff7fca168 CR3: 000000013b08a006 CR4: 0000000000471ef8
[ 7679.354984] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 7679.367207] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
[ 7679.379370] PKRU: 55555554
[ 7679.386446] Call Trace:
[ 7679.393152]  <TASK>
[ 7679.399363]  ? __pfx_dev_watchdog+0x10/0x10
[ 7679.407870]  call_timer_fn+0x31/0x110
[ 7679.415698]  expire_timers+0xb2/0x120
[ 7679.423403]  run_timer_softirq+0x179/0x1e0
[ 7679.431532]  ? __schedule+0x2b1/0x820
[ 7679.439078]  __do_softirq+0xd1/0x295
[ 7679.446426]  ? __pfx_smpboot_thread_fn+0x10/0x10
[ 7679.454867]  run_ksoftirqd+0x22/0x30
[ 7679.462058]  smpboot_thread_fn+0xb7/0x160
[ 7679.469670]  kthread+0xcd/0xf0
[ 7679.476097]  ? __pfx_kthread+0x10/0x10
[ 7679.483211]  ret_from_fork+0x29/0x50
[ 7679.490047]  </TASK>
[ 7679.495204] ---[ end trace 0000000000000000 ]---
[ 7679.503179] igc 0000:01:00.0 enp1s0: Register Dump
[ 7679.511230] igc 0000:01:00.0 enp1s0: Register Name   Value
[ 7679.519892] igc 0000:01:00.0 enp1s0: CTRL            181c0641
[ 7679.528782] igc 0000:01:00.0 enp1s0: STATUS          40280683
[ 7679.537551] igc 0000:01:00.0 enp1s0: CTRL_EXT        10000040
[ 7679.546284] igc 0000:01:00.0 enp1s0: MDIC            180a3800
[ 7679.554942] igc 0000:01:00.0 enp1s0: ICR             00000081
[ 7679.563503] igc 0000:01:00.0 enp1s0: RCTL            04408022
[ 7679.571963] igc 0000:01:00.0 enp1s0: RDLEN[0-3]      00001000 00001000 00001000 00001000
[ 7679.583075] igc 0000:01:00.0 enp1s0: RDH[0-3]        00000068 000000b6 0000000f 00000031
[ 7679.594162] igc 0000:01:00.0 enp1s0: RDT[0-3]        00000066 000000b2 0000000e 00000030
[ 7679.605174] igc 0000:01:00.0 enp1s0: RXDCTL[0-3]     02040808 02040808 02040808 02040808
[ 7679.616196] igc 0000:01:00.0 enp1s0: RDBAL[0-3]      1bb7c000 1bb7f000 1bb82000 0ef33000
[ 7679.627242] igc 0000:01:00.0 enp1s0: RDBAH[0-3]      00000001 00000001 00000001 00000001
[ 7679.638256] igc 0000:01:00.0 enp1s0: TCTL            a503f0fa
[ 7679.646607] igc 0000:01:00.0 enp1s0: TDBAL[0-3]      2ba4a000 1bb6f000 1bb74000 1bb79000
[ 7679.657609] igc 0000:01:00.0 enp1s0: TDBAH[0-3]      00000001 00000001 00000001 00000001
[ 7679.668551] igc 0000:01:00.0 enp1s0: TDLEN[0-3]      00001000 00001000 00001000 00001000
[ 7679.679470] igc 0000:01:00.0 enp1s0: TDH[0-3]        000000a7 0000002d 000000bf 000000d9
[ 7679.690406] igc 0000:01:00.0 enp1s0: TDT[0-3]        000000a7 0000002d 000000bf 000000d9
[ 7679.701264] igc 0000:01:00.0 enp1s0: TXDCTL[0-3]     02100108 02100108 02100108 02100108
[ 7679.712123] igc 0000:01:00.0 enp1s0: Reset adapter
[ 7683.085967] igc 0000:01:00.0 enp1s0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 8086.945561] ------------[ cut here ]------------
Entering kdb (current=0xffffffff8220b200, pid 0) on processor 0
Oops: (null) due to oops @ 0xffffffff81573888
RIP: 0010:dql_completed+0x148/0x160
Code: c9 00 48 89 57 58 e9 46 ff ff ff 45 85 e4 41 0f 95 c4 41 39 db 0f 95
c1 41 84 cc 74 05 45 85 ed 78 0a 44 89 c1 e9 27 ff ff ff <0f> 0b 01 f6 44 89
c1 29 f1 0f 48 ca eb 8c cc cc cc cc cc cc cc cc
RSP: 0018:ffa0000000003e00 EFLAGS: 00010287
RAX: 000000000000006c RBX: ffa0000003eb0f78 RCX: ff11000109938000
RDX: 0000000000000003 RSI: 0000000000000160 RDI: ff110001002e9480
RBP: ffa0000000003ed8 R08: ff110001002e93c0 R09: ffa0000000003d28
R10: 0000000000007cc0 R11: 0000000000007c54 R12: 00000000ffffffd9
R13: ff1100037039cb00 R14: 00000000ffffffd9 R15: ff1100037039c048
FS:  0000000000000000(0000) GS:ff11000361e00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffff7fca168 CR3: 000000013b08a003 CR4: 0000000000471ef8
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
 <IRQ>
 ? igc_poll+0x1a9/0x14d0 [igc]
 __napi_poll+0x2e/0x1b0
 net_rx_action+0x126/0x250
 __do_softirq+0xd1/0x295
 irq_exit_rcu+0xc5/0xf0
 common_interrupt+0x86/0xa0
 </IRQ>
 <TASK>
 asm_common_interrupt+0x27/0x40
RIP: 0010:cpuidle_enter_state+0xd3/0x3e0
Code: 73 f1 ff ff 49 89 c6 8b 05 e2 ca a7 00 85 c0 0f 8f b3 02 00 00 31 ff e8 1b
de 75 ff 80 7d d7 00 0f 85 cd 01 00 00 fb 45 85 ff <0f> 88 fd 00 00 00 49 63 cf
4c 2b 75 c8 48 8d 04 49 48 89 ca 48 8d
RSP: 0018:ffffffff82203df0 EFLAGS: 00000202
RAX: ff11000361e2a200 RBX: 0000000000000002 RCX: 000000000000001f
RDX: 0000000000000000 RSI: 000000003cf3cf3d RDI: 0000000000000000
RBP: ffffffff82203e28 R08: 0000075ae38471c8 R09: 0000000000000018
R10: 000000000000031a R11: ffffffff8238dca0 R12: ffd1ffffff200000
R13: ffffffff8238dca0 R14: 0000075ae38471c8 R15: 0000000000000002
 cpuidle_enter+0x2e/0x50
 call_cpuidle+0x23/0x40
 do_idle+0x1be/0x220
 cpu_startup_entry+0x20/0x30
 rest_init+0xb5/0xc0
 arch_call_rest_init+0xe/0x30
 start_kernel+0x448/0x760
 x86_64_start_kernel+0x109/0x150
 secondary_startup_64_no_verify+0xe0/0xeb
 </TASK>
more>
[0]kdb>

[0]kdb>
[0]kdb> go
Catastrophic error detected
kdb_continue_catastrophic=0, type go a second time if you really want to
continue
[0]kdb> go
Catastrophic error detected
kdb_continue_catastrophic=0, attempting to continue
[ 8086.955689] refcount_t: underflow; use-after-free.
[ 8086.955697] WARNING: CPU: 0 PID: 0 at lib/refcount.c:28 refcount_warn_saturate+0xc2/0x110
[ 8086.955706] Modules linked in: xt_conntrack nft_chain_nat xt_MASQUERADE xt_addrtype nft_compat
nf_tables nfnetlink br_netfilter bridge stp llc overlay dm_mod emrcha(PO) emriio(PO) rktpm(PO)
cegbuf_mod(PO) patch_update(PO) se(PO) sgx_tgts(PO) mktme(PO) keylocker(PO) svtdx(PO)
svfs_pci_hotplug(PO) vtd_mod(PO) davemem(PO) svmabort(PO) svindexio(PO) usbx2(PO) ehci_sched(PO)
svheartbeat(PO) ioapic(PO) sv8259(PO) svintr(PO) lt(PO) pcierootport(PO) enginefw_mod(PO) ata(PO)
smbus(PO) spiflash_cdf(PO) arden(PO) dsa_iax(PO) oobmsm_punit(PO) cpm(PO) svkdb(PO) ebg_pch(PO)
pch(PO) sviotargets(PO) svbdf(PO) svmem(PO) svbios(PO) dram(PO) svtsc(PO) targets(PO) superio(PO)
svkernel(PO) cswitch(PO) mcf(PO) pentiumIII_mod(PO) fs_svfs(PO) mdevdefdb(PO) svfs_os_services(O)
ixgbe mdio mdio_devres libphy emeraldrapids_svdefs(PO) regsupport(O) libnvdimm nls_cp437
snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_intel_dspcfg
snd_hda_codec snd_hwdep x86_pkg_temp_thermal snd_hda_core snd_pcm snd_timer isst_if_mbox_pci
[ 8086.955751]  input_leds isst_if_mmio sg snd isst_if_common soundcore wmi button sad9(O) drm
fuse backlight configfs efivarfs ip_tables x_tables vmd sdhci led_class rtl8150 r8152 hid_generic
pegasus mmc_block usbhid mmc_core hid megaraid_sas ixgb igb i2c_algo_bit ice i40e hpsa
scsi_transport_sas e1000e e1000 e100 ax88179_178a usbnet xhci_pci sd_mod xhci_hcd t10_pi
crc32c_intel crc64_rocksoft igc crc64 crc_t10dif usbcore crct10dif_generic ptp crct10dif_common
usb_common pps_core
[ 8086.955784] RIP: 0010:refcount_warn_saturate+0xc2/0x110
[ 8086.955788] Code: 01 e8 82 e7 b4 ff 0f 0b 5d c3 cc cc cc cc 80 3d 68 c6 eb 00 00 75 81
48 c7 c7 a0 87 f6 81 c6 05 58 c6 eb 00 01 e8 5e e7 b4 ff <0f> 0b 5d c3 cc cc cc cc 80 3d
42 c6 eb 00 00 0f 85 59 ff ff ff 48
[ 8086.955790] RSP: 0018:ffa0000000003da0 EFLAGS: 00010286
[ 8086.955793] RAX: 0000000000000000 RBX: ff1100011da40ee0 RCX: ff11000361e1b888
[ 8086.955794] RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ff11000361e1b880
[ 8086.955795] RBP: ffa0000000003da0 R08: 80000000ffff9f45 R09: ffa0000000003d28
[ 8086.955796] R10: ff1100035f840000 R11: 0000000000000028 R12: ff11000319ff8000
[ 8086.955797] R13: ff1100011bb79d60 R14: 00000000ffffffd6 R15: ff1100037039cb00
[ 8086.955798] FS:  0000000000000000(0000) GS:ff11000361e00000(0000) knlGS:0000000000000000
[ 8086.955800] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8086.955801] CR2: 00007ffff7fca168 CR3: 000000013b08a003 CR4: 0000000000471ef8
[ 8086.955803] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8086.955803] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
[ 8086.955804] PKRU: 55555554
[ 8086.955805] Call Trace:
[ 8086.955806]  <IRQ>
[ 8086.955808]  tcp_wfree+0x112/0x130
[ 8086.955814]  skb_release_head_state+0x24/0xa0
[ 8086.955818]  napi_consume_skb+0x9c/0x160
[ 8086.955821]  igc_poll+0x5d8/0x14d0 [igc]
[ 8086.955835]  __napi_poll+0x2e/0x1b0
[ 8086.955839]  net_rx_action+0x126/0x250
[ 8086.955843]  __do_softirq+0xd1/0x295
[ 8086.955846]  irq_exit_rcu+0xc5/0xf0
[ 8086.955851]  common_interrupt+0x86/0xa0
[ 8086.955857]  </IRQ>
[ 8086.955857]  <TASK>
[ 8086.955858]  asm_common_interrupt+0x27/0x40
[ 8086.955862] RIP: 0010:cpuidle_enter_state+0xd3/0x3e0
[ 8086.955866] Code: 73 f1 ff ff 49 89 c6 8b 05 e2 ca a7 00 85 c0 0f 8f b3 02 00 00 31 ff e8
1b de 75 ff 80 7d d7 00 0f 85 cd 01 00 00 fb 45 85 ff <0f> 88 fd 00 00 00 49 63 cf 4c 2b 75
c8 48 8d 04 49 48 89 ca 48 8d
[ 8086.955867] RSP: 0018:ffffffff82203df0 EFLAGS: 00000202
[ 8086.955869] RAX: ff11000361e2a200 RBX: 0000000000000002 RCX: 000000000000001f
[ 8086.955870] RDX: 0000000000000000 RSI: 000000003cf3cf3d RDI: 0000000000000000
[ 8086.955871] RBP: ffffffff82203e28 R08: 0000075ae38471c8 R09: 0000000000000018
[ 8086.955872] R10: 000000000000031a R11: ffffffff8238dca0 R12: ffd1ffffff200000
[ 8086.955873] R13: ffffffff8238dca0 R14: 0000075ae38471c8 R15: 0000000000000002
[ 8086.955875]  cpuidle_enter+0x2e/0x50
[ 8086.955880]  call_cpuidle+0x23/0x40
[ 8086.955884]  do_idle+0x1be/0x220
[ 8086.955887]  cpu_startup_entry+0x20/0x30
[ 8086.955889]  rest_init+0xb5/0xc0
[ 8086.955892]  arch_call_rest_init+0xe/0x30
[ 8086.955895]  start_kernel+0x448/0x760
[ 8086.955898]  x86_64_start_kernel+0x109/0x150
[ 8086.955900]  secondary_startup_64_no_verify+0xe0/0xeb
[ 8086.955904]  </TASK>
[ 8086.955904] ---[ end trace 0000000000000000 ]---
[ 8086.955912] ------------[ cut here ]------------
[ 8086.955913] kernel BUG at lib/dynamic_queue_limits.c:27!
[ 8086.955918] invalid opcode: 0000 [#1] SMP
[ 8086.955922] RIP: 0010:dql_completed+0x148/0x160
[ 8086.955925] Code: c9 00 48 89 57 58 e9 46 ff ff ff 45 85 e4 41 0f 95 c4 41 39 db
0f 95 c1 41 84 cc 74 05 45 85 ed 78 0a 44 89 c1 e9 27 ff ff ff <0f> 0b 01 f6 44 89
c1 29 f1 0f 48 ca eb 8c cc cc cc cc cc cc cc cc
[ 8086.955927] RSP: 0018:ffa0000000003e00 EFLAGS: 00010287
[ 8086.955928] RAX: 000000000000006c RBX: ffa0000003eb0f78 RCX: ff11000109938000
[ 8086.955929] RDX: 0000000000000003 RSI: 0000000000000160 RDI: ff110001002e9480
[ 8086.955930] RBP: ffa0000000003ed8 R08: ff110001002e93c0 R09: ffa0000000003d28
[ 8086.955931] R10: 0000000000007cc0 R11: 0000000000007c54 R12: 00000000ffffffd9
[ 8086.955932] R13: ff1100037039cb00 R14: 00000000ffffffd9 R15: ff1100037039c048
[ 8086.955933] FS:  0000000000000000(0000) GS:ff11000361e00000(0000) knlGS:0000000000000000
[ 8086.955934] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8086.955935] CR2: 00007ffff7fca168 CR3: 000000013b08a003 CR4: 0000000000471ef8
[ 8086.955936] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8086.955937] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
[ 8086.955938] PKRU: 55555554
[ 8086.955939] Call Trace:
[ 8086.955939]  <IRQ>
[ 8086.955940]  ? igc_poll+0x1a9/0x14d0 [igc]
[ 8086.955949]  __napi_poll+0x2e/0x1b0
[ 8086.955952]  net_rx_action+0x126/0x250
[ 8086.955956]  __do_softirq+0xd1/0x295
[ 8086.955958]  irq_exit_rcu+0xc5/0xf0
[ 8086.955961]  common_interrupt+0x86/0xa0
[ 8086.955964]  </IRQ>
[ 8086.955965]  <TASK>
[ 8086.955965]  asm_common_interrupt+0x27/0x40
[ 8086.955968] RIP: 0010:cpuidle_enter_state+0xd3/0x3e0
[ 8086.955971] Code: 73 f1 ff ff 49 89 c6 8b 05 e2 ca a7 00 85 c0 0f 8f b3 02 00 00
31 ff e8 1b de 75 ff 80 7d d7 00 0f 85 cd 01 00 00 fb 45 85 ff <0f> 88 fd 00 00 00
49 63 cf 4c 2b 75 c8 48 8d 04 49 48 89 ca 48 8d
[ 8086.955972] RSP: 0018:ffffffff82203df0 EFLAGS: 00000202
[ 8086.955973] RAX: ff11000361e2a200 RBX: 0000000000000002 RCX: 000000000000001f
[ 8086.955974] RDX: 0000000000000000 RSI: 000000003cf3cf3d RDI: 0000000000000000
[ 8086.955974] RBP: ffffffff82203e28 R08: 0000075ae38471c8 R09: 0000000000000018
[ 8086.955975] R10: 000000000000031a R11: ffffffff8238dca0 R12: ffd1ffffff200000
[ 8086.955976] R13: ffffffff8238dca0 R14: 0000075ae38471c8 R15: 0000000000000002
[ 8086.955978]  cpuidle_enter+0x2e/0x50
[ 8086.955981]  call_cpuidle+0x23/0x40
[ 8086.955984]  do_idle+0x1be/0x220
[ 8086.955985]  cpu_startup_entry+0x20/0x30
[ 8086.955987]  rest_init+0xb5/0xc0
[ 8086.955990]  arch_call_rest_init+0xe/0x30
[ 8086.955992]  start_kernel+0x448/0x760
[ 8086.955994]  x86_64_start_kernel+0x109/0x150
[ 8086.955996]  secondary_startup_64_no_verify+0xe0/0xeb
[ 8086.955998]  </TASK>
[ 8086.955999] Modules linked in: xt_conntrack nft_chain_nat xt_MASQUERADE xt_addrtype
nft_compat nf_tables nfnetlink br_netfilter bridge stp llc overlay dm_mod emrcha(PO) emriio(PO)
rktpm(PO) cegbuf_mod(PO) patch_update(PO) se(PO) sgx_tgts(PO) mktme(PO) keylocker(PO) svtdx(PO)
svfs_pci_hotplug(PO) vtd_mod(PO) davemem(PO) svmabort(PO) svindexio(PO) usbx2(PO) ehci_sched(PO)
svheartbeat(PO) ioapic(PO) sv8259(PO) svintr(PO) lt(PO) pcierootport(PO) enginefw_mod(PO) ata(PO)
smbus(PO) spiflash_cdf(PO) arden(PO) dsa_iax(PO) oobmsm_punit(PO) cpm(PO) svkdb(PO) ebg_pch(PO)
pch(PO) sviotargets(PO) svbdf(PO) svmem(PO) svbios(PO) dram(PO) svtsc(PO) targets(PO) superio(PO)
svkernel(PO) cswitch(PO) mcf(PO) pentiumIII_mod(PO) fs_svfs(PO) mdevdefdb(PO) svfs_os_services(O)
ixgbe mdio mdio_devres libphy emeraldrapids_svdefs(PO) regsupport(O) libnvdimm nls_cp437
snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_intel_dspcfg
snd_hda_codec snd_hwdep x86_pkg_temp_thermal snd_hda_core snd_pcm snd_timer isst_if_mbox_pci
[ 8086.956029]  input_leds isst_if_mmio sg snd isst_if_common soundcore wmi button sad9(O) drm
fuse backlight configfs efivarfs ip_tables x_tables vmd sdhci led_class rtl8150 r8152 hid_generic
pegasus mmc_block usbhid mmc_core hid megaraid_sas ixgb igb i2c_algo_bit ice i40e hpsa
scsi_transport_sas e1000e e1000 e100 ax88179_178a usbnet xhci_pci sd_mod xhci_hcd t10_pi
crc32c_intel crc64_rocksoft igc crc64 crc_t10dif usbcore crct10dif_generic ptp crct10dif_common
usb_common pps_core
[16762.543675] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 8675587.593 msecs
[16762.543678] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 8675587.595 msecs
[16762.543673] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 8675587.495 msecs
[16762.543679] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 8675587.599 msecs
[16762.543678] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 8675587.598 msecs
[16762.543690] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 8675587.605 msecs
[16762.543684] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 8675587.599 msecs
[16762.543693] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 8675587.613 msecs
[16762.543784] ---[ end trace 0000000000000000 ]---
[16762.849099] RIP: 0010:dql_completed+0x148/0x160
PANIC: Fatal exception in interrupt

Fixes: 9b27517627 ("igc: Add ndo_tx_timeout support")
Tested-by: Alejandra Victoria Alcaraz <alejandra.victoria.alcaraz@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-26 09:54:40 +01:00
Krzysztof Kozlowski
57f706bf73 ARM: dts: samsung: exynos4412-midas: add USB connector and USB OTG
Add full description of USB-MUIC (MAX77693 MUIC) and MUIC-MHL
connections, along with proper USB connector and OTG mode for DWC2 USB
controller.

This fixes dtc W=1 warnings:

  Warning (graph_child_address): /i2c-mhl/hdmi-bridge@39/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary

Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: replicant@osuosl.org
Cc: phone-devel@vger.kernel.org
Cc: ~postmarketos/upstreaming@lists.sr.ht
Cc: Martin Jücker <martin.juecker@gmail.com>
Cc: Henrik Grimler <henrik@grimler.se>
Cc: Artur Weber <aweber.kernel@gmail.com>
Tested-by: Henrik Grimler <henrik@grimler.se>
Link: https://lore.kernel.org/r/20230723142417.97734-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-07-26 10:51:41 +02:00
Krzysztof Kozlowski
7562d91450 ARM: dts: samsung: exynos5250-snow: switch i2c-arb to new child variant
Since commit e8813c15be ("dt-bindings: i2c: add support for 'i2c-arb'
subnode") the i2c-arbitrator subnode should not have unit address.

Link: https://lore.kernel.org/r/20230721133246.15752-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-07-26 10:51:07 +02:00
Krzysztof Kozlowski
4f861a9b81 ARM: dts: samsung: exynos5250-snow: use 'gpios' suffix for i2c-arb
Linux drivers support both variants - gpios and gpio - but first is
preferred.

Link: https://lore.kernel.org/r/20230721133246.15752-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
2023-07-26 10:51:07 +02:00
Christian Marangi
dfd739f182 net: dsa: qca8k: fix mdb add/del case with 0 VID
The qca8k switch doesn't support using 0 as VID and require a default
VID to be always set. MDB add/del function doesn't currently handle
this and are currently setting the default VID.

Fix this by correctly handling this corner case and internally use the
default VID for VID 0 case.

Fixes: ba8f870dfa ("net: dsa: qca8k: add support for mdb_add/del")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-26 08:50:10 +01:00
Christian Marangi
ae70dcb9d9 net: dsa: qca8k: fix broken search_and_del
On deleting an MDB entry for a port, fdb_search_and_del is used.
An FDB entry can't be modified so it needs to be deleted and readded
again with the new portmap (and the port deleted as requested)

We use the SEARCH operator to search the entry to edit by vid and mac
address and then we check the aging if we actually found an entry.

Currently the code suffer from a bug where the searched fdb entry is
never read again with the found values (if found) resulting in the code
always returning -EINVAL as aging was always 0.

Fix this by correctly read the fdb entry after it was searched.

Fixes: ba8f870dfa ("net: dsa: qca8k: add support for mdb_add/del")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-26 08:50:10 +01:00
Christian Marangi
80248d4160 net: dsa: qca8k: fix search_and_insert wrong handling of new rule
On inserting a mdb entry, fdb_search_and_insert is used to add a port to
the qca8k target entry in the FDB db.

A FDB entry can't be modified so it needs to be removed and insert again
with the new values.

To detect if an entry already exist, the SEARCH operation is used and we
check the aging of the entry. If the entry is not 0, the entry exist and
we proceed to delete it.

Current code have 2 main problem:
- The condition to check if the FDB entry exist is wrong and should be
  the opposite.
- When a FDB entry doesn't exist, aging was never actually set to the
  STATIC value resulting in allocating an invalid entry.

Fix both problem by adding aging support to the function, calling the
function with STATIC as aging by default and finally by correct the
condition to check if the entry actually exist.

Fixes: ba8f870dfa ("net: dsa: qca8k: add support for mdb_add/del")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-26 08:50:10 +01:00
Christian Marangi
2c39dd025d net: dsa: qca8k: enable use_single_write for qca8xxx
The qca8xxx switch supports 2 way to write reg values, a slow way using
mdio and a fast way by sending specially crafted mgmt packet to
read/write reg.

The fast way can support up to 32 bytes of data as eth packet are used
to send/receive.

This correctly works for almost the entire regmap of the switch but with
the use of some kernel selftests for dsa drivers it was found a funny
and interesting hw defect/limitation.

For some specific reg, bulk write won't work and will result in writing
only part of the requested regs resulting in half data written. This was
especially hard to track and discover due to the total strangeness of
the problem and also by the specific regs where this occurs.

This occurs in the specific regs of the ATU table, where multiple entry
needs to be written to compose the entire entry.
It was discovered that with a bulk write of 12 bytes on
QCA8K_REG_ATU_DATA0 only QCA8K_REG_ATU_DATA0 and QCA8K_REG_ATU_DATA2
were written, but QCA8K_REG_ATU_DATA1 was always zero.
Tcpdump was used to make sure the specially crafted packet was correct
and this was confirmed.

The problem was hard to track as the lack of QCA8K_REG_ATU_DATA1
resulted in an entry somehow possible as the first bytes of the mac
address are set in QCA8K_REG_ATU_DATA0 and the entry type is set in
QCA8K_REG_ATU_DATA2.

Funlly enough writing QCA8K_REG_ATU_DATA1 results in the same problem
with QCA8K_REG_ATU_DATA2 empty and QCA8K_REG_ATU_DATA1 and
QCA8K_REG_ATU_FUNC correctly written.
A speculation on the problem might be that there are some kind of
indirection internally when accessing these regs and they can't be
accessed all together, due to the fact that it's really a table mapped
somewhere in the switch SRAM.

Even more funny is the fact that every other reg was tested with all
kind of combination and they are not affected by this problem. Read
operation was also tested and always worked so it's not affected by this
problem.

The problem is not present if we limit writing a single reg at times.

To handle this hardware defect, enable use_single_write so that bulk
api can correctly split the write in multiple different operation
effectively reverting to a non-bulk write.

Cc: Mark Brown <broonie@kernel.org>
Fixes: c766e077d9 ("net: dsa: qca8k: convert to regmap read/write API")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-26 08:50:10 +01:00
Linus Walleij
f8ea950210 misc/genalloc: Name subpools by of_node_full_name()
A previous commit tried to come up with more generic subpool
names, but this isn't quite working: the node name was used
elsewhere to match pools to consumers which regressed the
nVidia Tegra 2/3 video decoder.

Revert back to an earlier approach using of_node_full_name()
instead of just the name to make sure the pool name is more
unique, and change both sites using this in the kernel.

It is not perfect since two SRAM nodes could have the same
subpool name but it makes the situation better than before.

Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: 21e5a2d10c ("misc: sram: Generate unique names for subpools")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20230622074520.3058027-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 09:45:01 +02:00
Greg Kroah-Hartman
645bb6b1fe Documentation: embargoed-hardware-issues.rst: add AMD to the list
Add AMD back to the embargoed-hardware-issues.rst list.  There was
confusion about a recent issue that ended up being due to third-party's
misrepresentation, not AMD, so add AMD back to the list to get notified
properly as they understand the proper procedures to follow.

Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/2023072514-submersed-yanking-652e@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 09:39:34 +02:00
Hans Verkuil
7baeedbe2b media: venus: core.h: update kerneldoc
Document missing fields. This resolves two warnings:

drivers/media/platform/qcom/venus/core.h:226: warning: Function parameter or member 'venus_ver' not described in 'venus_core'
drivers/media/platform/qcom/venus/core.h:501: warning: Function parameter or member 'enc_state' not described in 'venus_inst'

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
2023-07-26 09:35:04 +02:00
Kalle Valo
456b5e85d8 MAINTAINERS: add Jeff as ath10k, ath11k and ath12k maintainer
Jeff will now start maintaining these drivers together with me.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230725094248.3205486-1-kvalo@kernel.org
2023-07-26 10:14:38 +03:00
Kalle Valo
cc326aae03 MAINTAINERS: wifi: mark mlw8k as orphan
Last activity from Lennert is from 2012 so mark the driver as orphan.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-10-kvalo@kernel.org
2023-07-26 10:11:21 +03:00
Kalle Valo
3ccbc99c15 MAINTAINERS: wifi: mark b43 as orphan
There's no maintainer for b43 so mark it as orphan.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-9-kvalo@kernel.org
2023-07-26 10:11:21 +03:00
Kalle Valo
c1e0a70de1 MAINTAINERS: wifi: mark zd1211rw as orphan
Last activity from Ulrich is from 2007 so mark the driver orphan.

Remove the zd1211-devs list, I doubt anyone uses it anymore. The webpage seems
to be down so remove that as well.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-8-kvalo@kernel.org
2023-07-26 10:11:20 +03:00
Kalle Valo
0566ec9051 MAINTAINERS: wifi: mark wl3501 as orphan
There's no maintainer for this driver so mark it as orphan.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-7-kvalo@kernel.org
2023-07-26 10:11:20 +03:00
Kalle Valo
bc5dee3ce7 MAINTAINERS: wifi: mark rndis_wlan as orphan
Last activity from Jussi for this driver is from 2013 so mark the driver
orphan.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-6-kvalo@kernel.org
2023-07-26 10:11:20 +03:00
Kalle Valo
e76983151d MAINTAINERS: wifi: mark ar5523 as orphan
Last activity from Pontus for this driver is from 2013 so mark the driver
orphan.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-5-kvalo@kernel.org
2023-07-26 10:11:19 +03:00
Kalle Valo
74b81eac2d MAINTAINERS: wifi: mark cw1200 as orphan
Last activity from Solomon is from 2013 so mark the driver orphan.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-4-kvalo@kernel.org
2023-07-26 10:11:19 +03:00
Kalle Valo
25700d4916 MAINTAINERS: wifi: atmel: mark as orphan
Last activity from Simon is from 2005 so mark the driver is orphan.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-3-kvalo@kernel.org
2023-07-26 10:11:19 +03:00
Kalle Valo
96839282ed MAINTAINERS: wifi: rtw88: change Ping as the maintainer
Yan-Hsuan has been away since 2021 and Ping has been the de facto maintainer
the past year, actively reviewing patches and doing all other maintainer
duties. So fix the MAINTAINERS file to show the current situation.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724104547.3061709-2-kvalo@kernel.org
2023-07-26 10:11:19 +03:00
Kalle Valo
a1ce186db7 Revert "wifi: ath6k: silence false positive -Wno-dangling-pointer warning on GCC 12"
This reverts commit bd1d129daa.

The dangling-pointer warnings were disabled kernel-wide by commit 49beadbd47
("gcc-12: disable '-Wdangling-pointer' warning for now") for v5.19. So this
hack in ath6kl is not needed anymore.

Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230724100823.2948804-1-kvalo@kernel.org
2023-07-26 10:09:28 +03:00
Ilan Peer
fd7f08d92f wifi: cfg80211: Fix return value in scan logic
The reporter noticed a warning when running iwlwifi:

WARNING: CPU: 8 PID: 659 at mm/page_alloc.c:4453 __alloc_pages+0x329/0x340

As cfg80211_parse_colocated_ap() is not expected to return a negative
value return 0 and not a negative value if cfg80211_calc_short_ssid()
fails.

Fixes: c8cb5b854b ("nl80211/cfg80211: support 6 GHz scanning")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217675
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230723201043.3007430-1-ilan.peer@intel.com
2023-07-26 10:08:07 +03:00
Kalle Valo
d265ebe41c Revert "wifi: ath11k: Enable threaded NAPI"
This reverts commit 13aa2fb692.

This commit broke QCN9074 initialisation:

[  358.960477] ath11k_pci 0000:04:00.0: ce desc not available for wmi command 36866
[  358.960481] ath11k_pci 0000:04:00.0: failed to send WMI_STA_POWERSAVE_PARAM_CMDID
[  358.960484] ath11k_pci 0000:04:00.0: could not set uapsd params -105

As there's no fix available let's just revert it to get QCN9074 working again.

Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217536
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230720151444.2016637-1-kvalo@kernel.org
2023-07-26 09:56:53 +03:00
Rahul Singh
58f6259b7a xen/evtchn: Introduce new IOCTL to bind static evtchn
Xen 4.17 supports the creation of static evtchns. To allow user space
application to bind static evtchns introduce new ioctl
"IOCTL_EVTCHN_BIND_STATIC". Existing IOCTL doing more than binding
that’s why we need to introduce the new IOCTL to only bind the static
event channels.

Static evtchns to be available for use during the lifetime of the
guest. When the application exits, __unbind_from_irq() ends up being
called from release() file operations because of that static evtchns
are getting closed. To avoid closing the static event channel, add the
new bool variable "is_static" in "struct irq_info" to mark the event
channel static when creating the event channel to avoid closing the
static evtchn.

Also, take this opportunity to remove the open-coded version of the
evtchn close in drivers/xen/evtchn.c file and use xen_evtchn_close().

Signed-off-by: Rahul Singh <rahul.singh@arm.com>
Reviewed-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/ae7329bf1713f83e4aad4f3fa0f316258c40a3e9.1689677042.git.rahul.singh@arm.com
Signed-off-by: Juergen Gross <jgross@suse.com>
2023-07-26 08:42:34 +02:00
Jeffery Miller
92e24e0e57 Input: psmouse - add delay when deactivating for SMBus mode
There is a period of time between the psmouse deactivate and the
ability to communicate with the SMBus companion. Insert a
sleep after the deactivate to account for the delay and ensure
the SMBus companion is responsive.

Attempting to read from the SMBus companion too quickly was causing
the touchpad on machines with an i801_smbus companion to stop working
after a sleep/resume cycle.

On resume the rmi4_smbus would fail with errors reading the SMBus version
number:
```
[5454] i2c_i801:i801_check_post:414: i801_smbus 0000:00:1f.3: No response
smbus_result: i2c-0 a=02c f=0000 c=fd BYTE_DATA rd res=-6
rmi4_smbus 0-002c: failed to get SMBus version number!
...
rmi4_f01 rmi4-00.fn01: Failed to restore normal operation: -6.
rmi4_f01 rmi4-00.fn01: Resume failed with code -6.
rmi4_physical rmi4-00: Failed to suspend functions: -6
rmi4_smbus 0-002c: Failed to resume device: -6
```
In this case the rmi_smb_get_version fails with -ENXIO if it happens too
soon after the preceding serio_resume -> psmouse_deactivate call.

On boot this issue could cause the touchpad to stay in the limited PS/2
mode. This only reproduced in 1 in 10 boots on the Lenovo T440p.
Failures in the log on boot would show up as:
```
psmouse serio1: synaptics: Trying to set up SMBus access
[122] i2c_i801:i801_check_post:437: i801_smbus 0000:00:1f.3: No response
psmouse serio1: synaptics: SMbus companion is not ready yet
```

Experimentation on the Lenovo T440p showed that a delay of 7-12ms on
resume allowed the companion to respond.

The 30ms delay in this patch was chosen based on the linux-input message:
Link: https://lore.kernel.org/all/BYAPR03MB47572F2C65E52ED673238D41B2439@BYAPR03MB4757.namprd03.prod.outlook.com/

Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Link: https://lore.kernel.org/r/20230726025256.81174-1-jefferymiller@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2023-07-25 22:07:42 -07:00
Suraj Kandpal
4948738e29 drm/i915/hotplug: Reduce SHPD_FILTER to 250us
On TGP, the RTC (always running) was reduced from 3MHz to 32KHz.
As a result of this change, when HPD active going low pulse or HPD IRQ
is presented and the refclk (19.2MHz) is not toggling already toggling,
there is a 60 to 90us synchronization delay which effectively reduces
the duration of the IRQ pulse to less than the programmed 500us filter
value and the hot plug interrupt is NOT registered.
Solution was to Reduce SHPD_FILTER to 250us for ADL and above.
This solution was derived when the below patch was floated.
[1]https://patchwork.freedesktop.org/patch/532187
and after some internal discussion Ville's suggestion made sense.

Bspec: 68970

Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230720104624.3063544-1-suraj.kandpal@intel.com
2023-07-26 10:28:13 +05:30
Takashi Iwai
a85ff0db48 usb: gadget: midi2: More flexible MIDI 1.0 configuration
This patch allows users to set up MIDI 1.0 ports more flexibly.
Namely, instead of the fixed mapping only from FB 0, now multiple
block definitions are applied to build up the MIDI 1.0 mapping.

The each block config has midi1_first_group and midi1_num_groups
attributes, and those specify which Groups are used for MIDI 1.0.
Those fields must be within the UMP Groups defined in the block
itself.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-8-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Takashi Iwai
1b437d2fb3 usb: gadget: midi2: Add "Operation Mode" control
Add a new ALSA control element to watch the current operation mode
(MIDI 1.0 or MIDI 2.0).  It's a read-only control that reflects the
current value of altsetting, and 0 means unused, 1 for MIDI 1.0
(altset 0) and 2 for MIDI 2.0 (altset 1).

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-7-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Takashi Iwai
8559caa985 usb: gadget: midi2: Add testing documentation
Describing brief testing of the new MIDI 2.0 function driver.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-6-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Takashi Iwai
d6468be779 usb: gadget: midi2: MIDI 1.0 interface (altset 0) support
This patch extends MIDI 2.0 function driver to add more proper support
for MIDI 1.0 interface.  Before this patch, the driver only exposes
the USB descriptor of a MIDI 1.0 interface in altset 0 while no actual
I/O is running for it.  This patch enables the actual I/O for the
altset 0; the backend UMP rawmidi is translated from/to the MIDI 1.0
USB commands.

For converting to USB MIDI 1.0 data protocol, a helper function is
copied from the existing f_midi driver, in addition to a few other UMP
Core helper functions.  For the MIDI 1.0 OUT (that is, input for
gadget), the incoming USB MIDI 1.0 packet is translated to UMP packets
via UMP Core helper, and tossed to the attached UMP rawmidi.  It's a
relatively straightforward.  OTOH, for MIDI 1.0 IN (i.e. output for
gadget), it's a bit more complex: we need to convert a source UMP
packet once to the standard MIDI 1.0 byte stream, and convert it again
to USB MIDI 1.0 packets, then send them out.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-5-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Takashi Iwai
856fa444b0 usb: gadget: midi2: Dynamically create MIDI 1.0 altset descriptors
This patch extends MIDI 2.0 function driver to deal with more MIDI1
Jacks depending on the given Block configuration.

For MIDI 1.0, we take the configuration given in Function Block 0, and
create MIDI Jacks and Endpoints depending on the definition there.
That is, when more UMP Groups are defined in the Block 0, the
corresponding MIDI1 Jacks will be created.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-4-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Takashi Iwai
29ee7a4ddd usb: gadget: midi2: Add configfs support
This patch adds the support of configfs to MIDI 2.0 function driver
for users to allow configuring the UMP Endpoint and Function Blocks
more flexibly.  The configuration is in a tree form.  The top-most
contains some card-level configurations.  UMP Endpoints are defined in
subdirectories (ep.0, ep.1, etc) that contain Endpoint-specific
configurations such as ep_name, etc.  And, UMP Function Blocks are
defined in the subdirectories (block.0, block.1, etc) under EP
subdirectory.  As default, the driver creates a single UMP Endpoint
(ep.0) and a single Function Block (block.0) to work in a minimalistic
manner.  User can modify those attributes freely to fit with the
demands.

When multiple Function Blocks are required, user can create another
directory as block.1, block.2, and so on (up to block.31).  A block.*
directory can be deleted dynamically, too.  A caveat is that the block
number has to be continuous.

Similarly, when multiple UMP Endpoints are required, user can create
another directory as ep.1, ep.2, up to ep.3.

Also, some driver behavior can be controlled in the card top-level
configs.  e.g. you can pass process_ump=0 to disable the processing of
UMP Stream messages.  This would be equivalent with the older MIDI 2.0
spec that doesn't support UMP v1.1 features.

The configfs interface checks upper- / lower-bound of input values,
and more sanity checks are performed at binding.

Attributes can't be changed any longer once when the instance is
linked to UDC.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-3-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Takashi Iwai
8b645922b2 usb: gadget: Add support for USB MIDI 2.0 function driver
This patch adds the support for USB MIDI 2.0 gadget function driver.
The driver emulates a USB MIDI 2.0 interface with one or more UMP
Endpoints, where each of UMP Endpoint is a pair of MIDI Endpoints for
handling MIDI 2.0 UMP packets.  When the function driver is bound, the
driver creates an ALSA card object with UMP rawmidi devices.  This is
a kind of loop-back where the incoming and upcoming UMP packets
from/to the MIDI 2.0 UMP Endpoints are transferred as-is.  In
addition, legacy (MIDI 1.0) rawmidi devices are created, so that
legacy applications can work in the gadget side, too.

When a USB MIDI 2.0 gadget interface appears, the connected host can
use it with the snd-usb-audio driver where MIDI 2.0 support is
enabled.  Both gadget and connected hosts will have the similar UMP
Endpoint and Function Block (or Group Terminal Block) information.
Slight differences are the direction and UI-hint bits; it's due to the
nature of gadget driver, and the input/output direction is swapped in
both sides (the input for gadget is the output for host, and vice
versa).

The driver supports the brand-new UMP v1.1 feature, including the UMP
Stream message handling for providing UMP Endpoint and Function Block
information as well as dealing with the MIDI protocol switch.  The
driver responds to UMP Stream messages by itself.  OTOH, MIDI-CI
message handling isn't implemented in the kernel driver; it should be
processed in the user-space through the loopback UMP device.

As of this patch, the whole configuration is fixed, providing only one
bidirectional UMP Endpoint containing a single FB/GTB with a single
UMP Group.  The configuration will be dynamically changeable in the
following patches.

The traditional MIDI 1.0 is still provided in the altset 0 (which is
mandatory per spec).  But it's only about the configuration, and no
actual I/O will be running for the altset 0 as of this patch.  The
proper support MIDI 1.0 altset will follow in later patches, too.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230725062206.9674-2-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Stanley Chang
d6ef688786 dt-bindings: phy: realtek: Add Realtek DHC RTD SoC USB 3.0 PHY
Document the USB PHY bindings for Realtek SoCs.
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller and using USB 3.0 PHY transceiver.

Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230725033318.8361-5-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Stanley Chang
612ad27a30 dt-bindings: phy: realtek: Add Realtek DHC RTD SoC USB 2.0 PHY
Document the USB PHY bindings for Realtek SoCs.
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller and using USB 2.0 PHY transceiver.

Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230725033318.8361-4-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Stanley Chang
adda6e82a7 phy: realtek: usb: Add driver for the Realtek SoC USB 3.0 PHY
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 3.0 PHY transceivers.

Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-3-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Stanley Chang
134e6d25f6 phy: realtek: usb: Add driver for the Realtek SoC USB 2.0 PHY
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 2.0 PHY transceivers.

Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-2-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Stanley Chang
a08799cf17 usb: phy: add usb phy notify port status API
In Realtek SoC, the parameter of usb phy is designed to can dynamic
tuning base on port status. Therefore, add a notify callback of phy
driver when usb port status change.

The Realtek phy driver is designed to dynamically adjust disconnection
level and calibrate phy parameters. When the device connected bit changes
and when the disconnected bit changes, do port status change notification:

Check if portstatus is USB_PORT_STAT_CONNECTION and portchange is
USB_PORT_STAT_C_CONNECTION.
1. The device is connected, the driver lowers the disconnection level and
   calibrates the phy parameters.
2. The device disconnects, the driver increases the disconnect level and
   calibrates the phy parameters.

When controller to notify connect that device is already ready. If we
adjust the disconnection level in notify_connect, the disconnect may have
been triggered at this stage. So we need to change that as early as
possible. The status change of connection is before port reset.
Therefore, we add an api to notify phy the port status changes. In this
stage, the device is not port enable, and it will not trigger
disconnection.

Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230725033318.8361-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-26 06:38:14 +02:00
Jakub Kicinski
b57e0d48b3 Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:

====================
ice: switchdev bridge offload

Wojciech Drewek says:

Linux bridge provides ability to learn MAC addresses and vlans
detected on bridge's ports. As a result of this, FDB (forward data base)
entries are created and they can be offloaded to the HW. By adding
VF's port representors to the bridge together with the uplink netdev,
we can learn VF's and link partner's MAC addresses. This is achieved
by slow/exception-path, where packets that do not match any filters
(FDB entries in this case) are send to the bridge ports.

Driver keeps track of the netdevs added to the bridge
by listening for NETDEV_CHANGEUPPER event. We distinguish two types
of bridge ports: uplink port and VF's representor port. Linux
bridge always learns src MAC of the packet on rx path. With the
current slow-path implementation, it means that we will learn
VF's MAC on port repr (when the VF transmits the packet) and
link partner's MAC on uplink (when we receive it on uplink from LAN).

The driver is notified about learning of the MAC/VLAN by
SWITCHDEV_FDB_{ADD|DEL}_TO_DEVICE events. This is followed by creation
of the HW filter. The direction of the filter is based on port
type (uplink or VF repr). In case of the uplink, rule forwards
the packets to the LAN (matching on link partner's MAC). When the
notification is received on VF repr then the rule forwards the
packets to the associated VF (matching on VF's MAC).

This approach would not work on its own however. This is because if
one of the directions is offloaded, then the bridge would not be able
to learn the other one. If the egress rule is added (learned on uplink)
then the response from the VF will be sent directly to the LAN.
The packet will not got through slow-path, it would not be seen on
VF's port repr. Because of that, the bridge would not learn VF's MAC.

This is solved by introducing guard rule. It prevents forward rule from
working until the opposite direction is offloaded.

Aging is not fully supported yet, aging time is static for now. The
follow up submissions will introduce counters that will allow us to
keep track if the rule is actually being used or not.

A few fixes/changes are needed for this feature to work with ice driver.
These are introduced in first 5 patches.

Reviewed-by: Vlad Buslov <vladbu@nvidia.com>

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ice: add tracepoints for the switchdev bridge
  ice: implement static version of ageing
  ice: implement bridge port vlan
  ice: Add VLAN FDB support in switchdev mode
  ice: Add guard rule when creating FDB in switchdev
  ice: Switchdev FDB events support
  ice: Implement basic eswitch bridge setup
  ice: Unset src prune on uplink VSI
  ice: Disable vlan pruning for uplink VSI
  ice: Don't tx before switchdev is fully configured
  ice: Prohibit rx mode change in switchdev mode
  ice: Skip adv rules removal upon switchdev release
====================

Link: https://lore.kernel.org/r/20230724161152.2177196-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-25 21:10:20 -07:00
Masami Hiramatsu (Google)
02ab7234fc selftests/ftrace: Fix to check fprobe event eneblement
Fix to check the availability of fprobe and kprobes for
add_remove_btfarg.tc.
Only if both kprobe and fprobe are not supported, it should return
"unsupported".

Link: https://lore.kernel.org/all/169024904889.395371.17998733386857387118.stgit@devnote2/

Fixes: 4231f30fcc ("selftests/ftrace: Add BTF arguments test cases")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2023-07-26 12:54:17 +09:00
Masami Hiramatsu (Google)
1f9f4f4777 tracing/probes: Fix to add NULL check for BTF APIs
Since find_btf_func_param() abd btf_type_by_id() can return NULL,
the caller must check the return value correctly.

Link: https://lore.kernel.org/all/169024903951.395371.11361556840733470934.stgit@devnote2/

Fixes: b576e09701 ("tracing/probes: Support function parameters if BTF is available")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2023-07-26 12:53:38 +09:00
Johannes Zink
20bf98c941 net: stmmac: correct MAC propagation delay
The IEEE1588 Standard specifies that the timestamps of Packets must be
captured when the PTP message timestamp point (leading edge of first
octet after the start of frame delimiter) crosses the boundary between
the node and the network. As the MAC latches the timestamp at an
internal point, the captured timestamp must be corrected for the
additional path latency, as described in the publicly available
datasheet [1].

This patch only corrects for the MAC-Internal delay, which can be read
out from the MAC_Ingress_Timestamp_Latency register, since the Phy
framework currently does not support querying the Phy ingress and egress
latency. The Closs Domain Crossing Circuits errors as indicated in [1]
are already being accounted in the stmmac_get_tx_hwtstamp() function and
are not corrected here.

As the Latency varies for different link speeds and MII
modes of operation, the correction value needs to be updated on each
link state change.

As the delay also causes a phase shift in the timestamp counter compared
to the rest of the network, this correction will also reduce phase error
when generating PPS outputs from the timestamp counter.

[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"

Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v2-1-3366f38ee9a6@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-25 20:37:21 -07:00