Get rid of page_align_ptr() and use PTR_ALIGN() instead.
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Simplify memory allocation for diagnose 204 memory buffer:
- allocate with __vmalloc_node() to enure page alignment
- allocate real / physical memory area also within vmalloc area and handle
vmalloc to real / physical address translation within diag204().
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Mete Durlu <meted@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove the legacy device driver code for CEX2 and CEX3 cards.
The last machines which are able to handle CEX2 crypto cards
are z10 EC first available 2008 and z10 BC first available 2009.
The last machines able to handle a CEX3 crypto card are
z196 first available 2010 and z114 first available 2011.
Please note that this does not imply to drop CEX2 and CEX3
support in general. With older kernels on hardware up to the
aforementioned machine models these crypto cards will get
support by IBM.
The removal of the CEX2 and CEX3 device drivers code opens up
some simplifications, for example support for crypto cards
without rng support can be removed also.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
vmalloc() does not guarantee any alignment, unless it is explicitly
requested with e.g. __vmalloc_node(). Using diag204() with subcode 7
requires a 4k aligned virtual buffer. Therefore switch to __vmalloc_node().
Note: with the current vmalloc() implementation callers would still get a
4k aligned area, even though this is quite non-obvious looking at the
code. So changing this in sthyi doesn't fix a real bug. It is just to make
sure the code will not suffer from some obscure options, like it happened
in the past with kmalloc() where debug options changed the assumed
alignment of allocated memory areas.
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Diagnose 204 subcode 4 requires a real (physical) address, but a
virtual address is passed to the inline assembly.
Convert the address to a physical address for only this specific case.
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Enable receiving the user-defined certificates from the s390x
hypervisor via new diagnose 0x320 calls, and make them available to the
Linux root user as 'cert_store_key' type keys in a so-called
'cert_store' keyring.
New user-space interfaces:
/sys/firmware/cert_store/refresh
Writing to this attribute re-fetches certificates via DIAG 0x320
/sys/firmware/cert_store/cs_status
Reading from this attribute returns either of:
"uninitialized"
If no certificate has been retrieved yet
"ok"
If certificates have been successfully retrieved
"failed (<number>)"
If certificate retrieval failed with reason code <number>
New debug trace areas:
/sys/kernel/debug/s390dbf/cert_store_msg
/sys/kernel/debug/s390dbf/cert_store_hexdump
Usage example:
To initiate request for certificates available to the system as root:
$ echo 1 > /sys/firmware/cert_store/refresh
Upon success the '/sys/firmware/cert_store/cs_status' contains
the value 'ok'.
$ cat /sys/firmware/cert_store/cs_status
ok
Get the ID of the keyring 'cert_store':
$ keyctl search @us keyring cert_store
OR
$ keyctl link @us @s; keyctl request keyring cert_store
Obtain list of IDs of certificates:
$ keyctl rlist <cert_store keyring ID>
Display certificate content as hex-dump:
$ keyctl read <certificate ID>
Read certificate contents as binary data:
$ keyctl pipe <certificate ID> >cert_data
Display certificate description:
$ keyctl describe <certificate ID>
The certificate description has the following format:
<64 bytes certificate name in EBCDIC> ':'
<certificate index as obtained from hypervisor> ':'
<certificate store token obtained from hypervisor>
The certificate description in /proc/keys has certificate name
represented in ASCII.
Users can read but cannot update the content of the certificate.
Signed-off-by: Anastasia Eskova <anastasia.eskova@ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Jiri Benc says:
====================
vxlan: fix GRO with VXLAN-GPE
The first patch generalizes code for the second patch, which is a fix for
broken VXLAN-GPE GRO. Thanks to Paolo for noticing the bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In VXLAN-GPE, there may not be an Ethernet header following the VXLAN
header. But in GRO, the vxlan driver calls eth_gro_receive
unconditionally, which means the following header is incorrectly parsed
as Ethernet.
Introduce GPE specific GRO handling.
For better performance, do not check for GPE during GRO but rather
install a different set of functions at setup time.
Fixes: e1e5314de0 ("vxlan: implement GPE")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vxlan_parse_gpe_hdr function extracts the next protocol value from
the GPE header and marks GPE bits as parsed.
In order to be used in the next patch, split the function into protocol
extraction and bit marking. The bit marking is meaningful only in
vxlan_rcv; move it directly there.
Rename the function to vxlan_parse_gpe_proto to reflect what it now
does. Remove unused arguments skb and vxflags. Move the function earlier
in the file to allow it to be called from more places in the next patch.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson says:
====================
ionic: add FLR support
Add support for handing and recovering from a PCI FLR event.
This patchset first moves some code around to make it usable
from multiple paths, then adds the PCI error handler callbacks
for reset_prepare and reset_done.
Example test:
echo 1 > /sys/bus/pci/devices/0000:2a:00.0/reset
v4:
- don't remove ionic_dev_teardown() in ionic_probe() in patch 2/4
- remove clear_bit() change from patch 3/4
v3:
Link: https://lore.kernel.org/netdev/20230717170001.30539-1-shannon.nelson@amd.com/
- removed first patch, it is already merged into net
v2:
Link: https://lore.kernel.org/netdev/20230713192936.45152-1-shannon.nelson@amd.com/
- removed redundant pci_save/restore_state() calls
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the PCI reset handlers in order to manage an FLR event.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull out some code from ionic_lif_handle_fw_up() that can be
used in the coming FLR recovery patch.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull out some chunks of code from ionic_probe() that will
be common in rebuild paths.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull out a chunk of code from ionic_remove() that will
be common in teardown paths.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in atl1c_tso_csum, it should check the return value of pskb_trim(),
and return an error code if an unexpected value is returned
by pskb_trim().
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samin Guo says:
====================
Add motorcomm phy pad-driver-strength-cfg support
The motorcomm phy (YT8531) supports the ability to adjust the drive
strength of the rx_clk/rx_data, and the default strength may not be
suitable for all boards. So add configurable options to better match
the boards.(e.g. StarFive VisionFive 2)
The first patch adds a description of dt-bingding, and the second patch adds
YT8531's parsing and settings for pad-driver-strength-cfg.
Changes since v4:
Patch 1:
- Removed register-related DS(3b) values and added vol descriptions (by Andrew Lunn)
- Dropped the type and added '-microamp' suffix. (by Rob Herring)
Patch 2:
- Return -EINVAL if the value in DT but it is invalid (by Andrew Lunn)
Changes since v3:
Patch 1:
- Used current values instead of register values
- Added units and numerical descriptions of driver-strength
Patch 2:
- Added a lookup table to listing the valid values in the schema (by Andrew Lunn)
Changes since v2:
Patch 2:
- Readjusted the order of YT8531_RGMII_xxx to below YTPHY_PAD_DRIVE_STRENGTH_REG (by Frank Sae)
- Reversed Christmas tree, sort these longest first, shortest last (by Andrew Lunn)
- Rebased on tag v6.4
Changes since v1:
Patch 1:
- Renamed "rx-xxx-driver-strength" to "motorcomm,rx-xxx-driver-strength" (by Frank Sae)
Patch 2:
- Added default values for rxc/rxd driver strength (by Frank Sea/Andrew Lunn)
- Added range checking when val is in DT (by Frank Sea/Andrew Lunn)
Previous versions:
v1 - https://patchwork.kernel.org/project/netdevbpf/cover/20230426063541.15378-1-samin.guo@starfivetech.com
v2 - https://patchwork.kernel.org/project/netdevbpf/cover/20230505090558.2355-1-samin.guo@starfivetech.com
v3 - https://patchwork.kernel.org/project/netdevbpf/cover/20230526090502.29835-1-samin.guo@starfivetech.com
v4 - https://patchwork.kernel.org/project/netdevbpf/cover/20230714101406.17686-1-samin.guo@starfivetech.com
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The motorcomm phy (YT8531) supports the ability to adjust the drive
strength of the rx_clk/rx_data, and the default strength may not be
suitable for all boards. So add configurable options to better match
the boards.(e.g. StarFive VisionFive 2)
When we configure the drive strength, we need to read the current
LDO voltage value to ensure that it is a legal value at that LDO
voltage.
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The motorcomm phy (YT8531) supports the ability to adjust the drive
strength of the rx_clk/rx_data.
The YT8531 RGMII LDO voltage supports 1.8V/3.3V, and the
LDO voltage can be configured with hardware pull-up resistors to match
the SOC voltage (usually 1.8V). The software can read the registers
0xA001 obtain the current LDO voltage value.
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we only mute after playback has finished, and unmute
prior to setting global enable. To prevent any possible pops
and clicks, mute at probe, and then only unmute after global
enable is set.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-12-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To ensure consistency between the HDA core and the CS35L41 HDA
driver, add a device_link between them. This ensures that the
HDA core will suspend first, and resume second, meaning the
amp driver will not miss any events from the playback hook from
the HDA core during system suspend and resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-11-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to correctly pause audio on suspend, amps using external boost
require parts of the pause sequence to be called for all amps before moving
on to the next steps.
For example, as part of pausing the audio, the VSPK GPIO must be disabled,
but since this GPIO is controlled by one amp, but controls the boost for
all amps, it is required to separate the calls.
During playback this is achieved by using the pre and post playback hooks,
however during system suspend, this is not possible, so to separate the
calls, we use both the .prepare and .suspend calls to pause the audio.
Currently, for this reason, we do not restart audio on system resume.
However, we can support this by relying on the playback hook to resume
playback after system suspend.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-10-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use new hooks to ensure separation between play/pause actions,
as required by external boost.
External Boost on CS35L41 requires the amp to go through a
particular sequence of steps. One of these steps involes
the setting of a GPIO. This GPIO is connected to one or
more of the amps, and it may control the boost for all of
the amps. To ensure that the GPIO is set when it is safe
to do so, and to ensure that boost is ready for the rest of
the sequence to be able to continue, we must ensure that
the each part of the sequence is executed for each amp
before moving on to the next part of the sequence.
Some of the Play and Pause actions have moved from Open to
Prepare. This is because Open is not guaranteed to be called
again on system resume, whereas Prepare should.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-9-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These hooks can be used to add callbacks that would be run before and after
the main playback hooks. These hooks would be called for all amps, before
moving on to the next hook, i.e. pre_playback_hook would be called for
all amps, before the playback_hook is called for all amps, then finally
the post_playback_hook is called for all amps.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are several steps required to put the system into system suspend.
Some of these steps may fail, so the driver should pass up the errors
if they occur.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to properly system suspend, it is necessary to unload the firmware
and ensure the chip is ready for shutdown (if necessary). If the system
is currently in runtime suspend, it is necessary to wake up the device,
and then make it ready. Currently, the wake does not correctly resync
the device, which may mean it cannot suspend correctly. Fix this by
performaing a resync.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, we do not check the return status of the pause command,
immediately after we load firmware. If the pause has failed,
the firmware is not running.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To ensure the chip has correctly powered up or down before continuing,
the driver will now poll a register, rather than wait a fixed delay.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To enable the speaker output in external boost mode, 2 registers must
be set, one after another. The longer the time between the writes of
the two registers, the more likely, and more loudly a pop may occur.
To minimize this, an mbox command can be used to allow the firmware
to perform this action, minimizing any delay between write, thus
minimizing any pop or click as a result. The old method will remain
when running without firmware.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IPv6 inet sockets are supposed to have a "struct ipv6_pinfo"
field at the end of their definition, so that inet6_sk_generic()
can derive from socket size the offset of the "struct ipv6_pinfo".
This is very fragile, and prevents adding bigger alignment
in sockets, because inet6_sk_generic() does not work
if the compiler adds padding after the ipv6_pinfo component.
We are currently working on a patch series to reorganize
TCP structures for better data locality and found issues
similar to the one fixed in commit f5d547676c
("tcp: fix tcp_inet6_sk() for 32bit kernels")
Alternative would be to force an alignment on "struct ipv6_pinfo",
greater or equal to __alignof__(any ipv6 sock) to ensure there is
no padding. This does not look great.
v2: fix typo in mptcp_proto_v6_init() (Paolo)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Chao Wu <wwchao@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Coco Li <lixiaoyan@google.com>
Cc: YiFei Zhu <zhuyifei@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two drivers embed a i2c_client in their private driver data, but
only strict device is actually needed. Replace the i2c_client reference
with a struct device one.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230718110407.1005200-1-wenst@chromium.org
VXLAN-GPE does not add an extra inner Ethernet header. Take that into
account when calculating header length.
This causes problems in skb_tunnel_check_pmtu, where incorrect PMTU is
cached.
In the collect_md mode (which is the only mode that VXLAN-GPE
supports), there's no magic auto-setting of the tunnel interface MTU.
It can't be, since the destination and thus the underlying interface
may be different for each packet.
So, the administrator is responsible for setting the correct tunnel
interface MTU. Apparently, the administrators are capable enough to
calculate that the maximum MTU for VXLAN-GPE is (their_lower_MTU - 36).
They set the tunnel interface MTU to 1464. If you run a TCP stream over
such interface, it's then segmented according to the MTU 1464, i.e.
producing 1514 bytes frames. Which is okay, this still fits the lower
MTU.
However, skb_tunnel_check_pmtu (called from vxlan_xmit_one) uses 50 as
the header size and thus incorrectly calculates the frame size to be
1528. This leads to ICMP too big message being generated (locally),
PMTU of 1450 to be cached and the TCP stream to be resegmented.
The fix is to use the correct actual header size, especially for
skb_tunnel_check_pmtu calculation.
Fixes: e1e5314de0 ("vxlan: implement GPE")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jijie Shao says:
====================
There are some bugfix for the HNS3 ethernet driver
There are some bugfix for the HNS3 ethernet driver
====================
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dwrr mode, the default bandwidth weight of disabled tc is set to 0.
If the bandwidth weight is 0, the mode will change to sp.
Therefore, disabled tc default bandwidth weight need changed to 1,
and 0 is returned when query the bandwidth weight of disabled tc.
In addition, driver need stop configure bandwidth weight if tc is disabled.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the weight saved by the driver is used as the query result,
which may be different from the actual weight in the register.
Therefore, the register value read from the firmware is used
as the query result
Fixes: 0e32038dc8 ("net: hns3: refactor dump tc of debugfs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tm module is configured with traffic, traffic
may be abnormal. This patch fixes this problem.
Before the tm module is configured, traffic processing
should be stopped. After the tm module is configured,
traffic processing is enabled.
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current only the first 32 bits of the capability flag bit are considered.
When the matching capability flag bit is greater than 31 bits,
it will get an error bit.This patch use bitmap to solve this issue.
It can handle each capability bit whitout bit width limit.
Fixes: da77aef9cc ("net: hns3: create common cmdq resource allocate/free/query APIs")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the spaces with tab characters in the Kconfig file.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230712065054.2377278-1-wenst@chromium.org
While these aren't generally visible from userland, it's best to be
consistent with timestamp handling. When adjusting the quota, update the
mtime and ctime like we would with a write operation on any other inode,
and avoid updating the atime which should only be done for reads.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Message-Id: <20230713135249.153796-1-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Now that everything in-tree is converted to use the accessor functions,
rename the i_ctime field in the inode to discourage direct access.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705185812.579118-4-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-89-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-88-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-87-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-86-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-85-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-84-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-83-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-82-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-81-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-80-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>