of_gpio.h provides a single function, which is not used in this driver.
Remove unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Valid configurations for the extcon interrupt declarations are
- usb_id
- usb_vbus
- (usb_id | usb_vbus)
In the case of a standalone usb_id or usb_vbus failure to find one of the
interrupts shouldn't generate a warning message. A warning is already in
place if both IRQs are missing.
Switch to using platform_get_irq_byname_optional() in order to facilitate
this behaviour.
Suggested-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
dts validation is throwing an error for me on 8916 and 8939 with
extcon@1300. In that case we have usb_vbus but not usb_id.
It wasn't immediately obvious if there was a valid use-case for the
existing code for usb_id in isolation, however discussing further, we
concluded that usb_id, usb_vbus or (usb_id | usb_vbus) are valid
combinations as an external IC may be responsible for usb_id or usb_vbus.
Expand the definition with anyOf to capture the three different valid
modes.
Fixes: 4fcdd677c4 ("bindings: pm8941-misc: Add support for VBUS detection")
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The spmi-pmic bindings is now using usb-detect@ for this node, so adjust
the example to match.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The driver can register a typec port if suitable firmware properties are
present. But if the driver is removed through sysfs unbind, rmmod or
similar, then it does not clean up after itself and the typec port
device remains registered. This can be seen in sysfs, where stale typec
ports get left over in /sys/class/typec.
In order to fix this we have to add an i2c_driver remove function and
call typec_unregister_port(), which is a no-op in the case where no
typec port is created and the pointer remains NULL.
In the process we should also put the fwnode_handle when the typec port
isn't registered anymore, including if an error occurs during probe. The
typec subsystem does not increase or decrease the reference counter for
us, so we track it in the driver's private data.
Note that the conditional check on TYPEC_PWR_MODE_PD was removed in the
probe path because a call to tusb320_set_adv_pwr_mode() will perform an
even more robust validation immediately after, hence there is no
functional change here.
Fixes: bf7571c00d ("extcon: usbc-tusb320: Add USB TYPE-C support")
Cc: stable@vger.kernel.org
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to guard sections of code calling them
as alternative access methods with CONFIG_HAS_IOPORT checks. For
uhci-hcd there are a lot of I/O port uses that do have MMIO alternatives
all selected by uhci_has_pci_registers() so this can be handled by
UHCI_IN/OUT macros and making uhci_has_pci_registers() constant 0 if
CONFIG_HAS_IOPORT is unset.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230522105049.1467313-38-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hayato's Realtek WiFi/BT module has it's Bluetooth function wired to
UART1.
Add and enable the relevant device nodes for it.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20230424100409.2992418-1-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-37-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
smatch warning:
drivers/devfreq/mtk-cci-devfreq.c:135 mtk_ccifreq_target()
warn: variable dereferenced before check 'drv' (see line 130)
This is based on static analysis only. Compilation tested.
Signed-off-by: Sukrut Bellary <sukrut.bellary@linux.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The "udc" pointer was never set in the probe() function so it will
lead to a NULL dereference in udc_pci_remove() when we do:
usb_del_gadget_udc(&udc->gadget);
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ZG+A/dNpFWAlCChk@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit adf8238ef4 ("ARM: dts: exynos: move exynos-bus nodes out of soc
in Exynos4412") changed the order of the exynos-bus nodes, what results
in different probe order of the Exynos Bus devices. Although the driver
properly handles the deferred probe and all devices seems to be finally
properly registered, this change revealed some kind of a bug related to
PPMU counters registration and passive governor operation. Usually in 1
of 10 boots this results in complete board freeze during loading of the
kernel modules.
To avoid that freeze, ensure that the Exynos PPMU driver is already
loaded before the Exynos Bus driver starts probing.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
While exercising the unbind path, with the current implementation
the functionfs_unbind would be calling which waits for the ffs->mutex
to be available, however within the same time ffs_ep0_read is invoked
& if no setup packets are pending, it will invoke function
wait_event_interruptible_exclusive_locked_irq which by definition waits
for the ev.count to be increased inside the same mutex for which
functionfs_unbind is waiting.
This creates deadlock situation because the functionfs_unbind won't
get the lock until ev.count is increased which can only happen if
the caller ffs_func_unbind can proceed further.
Following is the illustration:
CPU1 CPU2
ffs_func_unbind() ffs_ep0_read()
mutex_lock(ffs->mutex)
wait_event(ffs->ev.count)
functionfs_unbind()
mutex_lock(ffs->mutex)
mutex_unlock(ffs->mutex)
ffs_event_add()
<deadlock>
Fix this by moving the event unbind before functionfs_unbind
to ensure the ev.count is incrased properly.
Fixes: 6a19da1110 ("usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait")
Cc: stable <stable@kernel.org>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20230525092854.7992-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At iMX8QM platform, enable NCM gadget and run 'iperf3 -s'.
At host, run 'iperf3 -V -c fe80::6863:98ff:feef:3e0%enxc6e147509498'
[ 5] 0.00-1.00 sec 1.55 MBytes 13.0 Mbits/sec 90 4.18 KBytes
[ 5] 1.00-2.00 sec 1.44 MBytes 12.0 Mbits/sec 75 4.18 KBytes
[ 5] 2.00-3.00 sec 1.48 MBytes 12.4 Mbits/sec 75 4.18 KBytes
Expected speed should be bigger than 300Mbits/sec.
The root cause of this performance drop was found to be data corruption
happening at 4K borders in some Ethernet packets, leading to TCP
checksum errors. This corruption occurs from the position
(4K - (address & 0x7F)) to 4K. The u_ether function's allocation of
skb_buff reserves 64B, meaning all RX addresses resemble 0xXXXX0040.
Force trb_burst_size to 16 can fix this problem.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230518154946.3666662-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ba751e28d4 ("net: dsa: mt7530: add interrupt support")
the mt7530 driver can act as an interrupt controller. Wire up irq line
of the MT7531 switch on the BananaPi BPi-R64 board, so the status of
the PHYs of the five 1000Base-T ports doesn't need to be polled any
more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZEA-DV_OsmFg5egL@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Group some variables based on their sizes to reduce holes.
On x86_64, this shrinks the size of 'struct devfreq_dev_status' from 72 to
64 bytes.
This structure is used both to allocate static variables or is embedded in
some other structures. In both cases, reducing its size is nice to have.
Moreover, the whole structure now fits in a single cache line on x86_64.
Finally, it makes the order of code match the order of the above kernel
doc.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The SPI-NOR node in the device tree of the BananaPi R64 has most likely
been copied from the reference board's device tree even though the R64
comes with an SPI-NAND chip rather than SPI-NOR.
Setup the Serial NAND Flash Interface (SNFI) controller, enable
hardware BCH error detection and correction engine and add the SPI-NAND
chip including basic partitions,
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZEA96dmaXqTpk8u8@makrotopia.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
ISOC transfers expect a certain cadence of requests being queued. Not
keeping up with the expected rate of requests results in missed ISOC
transfers (EXDEV). The application layer may or may not produce video
frames to match this expectation, so uvc gadget driver must handle cases
where the application is not queuing up buffers fast enough to fulfill
ISOC requirements.
Currently, uvc gadget driver waits for new video buffer to become available
before queuing up usb requests. With this patch the gadget driver queues up
0 length usb requests whenever there are no video buffers available. The
USB controller's complete callback is used as the limiter for how quickly
the 0 length packets will be queued. Video buffers are still queued as
soon as they become available.
Link: https://lore.kernel.org/CAMHf4WKbi6KBPQztj9FA4kPvESc1fVKrC8G73-cs6tTeQby9=w@mail.gmail.com/
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20230508231103.1621375-1-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When serial console over USB is enabled, gs_console_connect
queues gs_console_work, where it acquires the spinlock and
queues the usb request, and this request goes to gadget layer.
Now consider a situation where gadget layer prints something
to dmesg, this will eventually call gs_console_write() which
requires cons->lock. And this causes spinlock recursion. Avoid
this by excluding usb_ep_queue from the spinlock.
spin_lock_irqsave //needs cons->lock
gs_console_write
.
.
_printk
__warn_printk
dev_warn/pr_err
.
.
[USB Gadget Layer]
.
.
usb_ep_queue
gs_console_work
__gs_console_push // acquires cons->lock
process_one_work
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1683638872-6885-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider a case where gserial_disconnect has already cleared
gser->ioport. And if gserial_suspend gets called afterwards,
it will lead to accessing of gser->ioport and thus causing
null pointer dereference.
Avoid this by adding a null pointer check. Added a static
spinlock to prevent gser->ioport from becoming null after
the newly added null pointer check.
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1683278317-11774-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
orientation-switch it the standard declaration to inform the Type-C mux
layer that a remote-endpoint is capable of processing orientation change
messages.
Add as an optional since not all versions of the dp-phy currently support
the orientation-switch.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230515133643.3621656-4-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VBUS driver needs to know the regulator-min-microamp and
regulator-max-microamp so they should both be marked as required.
regulator.yaml defines those two dependencies so include regulator.yaml.
We need to change from additionalProperties: false to
unevaluatedProperties: false.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230515133643.3621656-3-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regulator code needs to know the location of the register to write to
to switch on/off. Right now we have a driver that does this, a yaml that
partially describes it and no dts that uses it.
Switching on the VBUS for sm8250 shows that we haven't documented reg as a
required property, do so now.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230515133643.3621656-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hdr->opcode is __le32 type, use le32_to_cpu() to cast opcode
to integer in the switch..case statement to fix the following
sparse warnings:
drivers/usb/typec/ucsi/ucsi_glink.c:248:20: sparse: warning: restricted __le32 degrades to integer
drivers/usb/typec/ucsi/ucsi_glink.c:248:20: sparse: warning: restricted __le32 degrades to integer
drivers/usb/typec/ucsi/ucsi_glink.c:248:20: sparse: warning: restricted __le32 degrades to integer
No functional change.
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230523162314.114274-1-minhuadotchen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
power_supply_is_system_supplied() checks whether any power
supplies are present that aren't batteries to decide whether
the system is running on DC or AC. Downstream drivers use
this to make performance decisions.
Navi dGPUs include an UCSI function that has been exported
since commit 17631e8ca2 ("i2c: designware: Add driver
support for AMD NAVI GPU").
This UCSI function registers a power supply since commit
992a60ed0d ("usb: typec: ucsi: register with power_supply class")
but this is not a system power supply.
As the power supply for a dGPU is only for powering devices connected
to dGPU, create a device property to indicate that the UCSI endpoint
is only for the scope of `POWER_SUPPLY_SCOPE_DEVICE`.
Link: https://lore.kernel.org/lkml/20230516182541.5836-2-mario.limonciello@amd.com/
Reviewed-by: Evan Quan <evan.quan@amd.com>
Tested-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230518161150.92959-1-mario.limonciello@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function dwc3_qcom_probe() allocates memory for resource structure
which is pointed by parent_res pointer. This memory is not
freed. This leads to memory leak. Use stack memory to prevent
memory leak.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20230517172518.442591-1-VEfanov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
smatch reports
drivers/usb/typec/tcpm/qcom/qcom_pmic_typec.c:323:29: warning: symbol
'pm8150b_typec_res' was not declared. Should it be static?
This variable is only used in its defining file, so it should be static
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230515114043.3452010-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_FORTIFY_SOURCE=2 uses more and stricter checks. This is what e.g.
Debian recommends to build packages with.
While at it fix a typo in the output of ./configure --help.
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Reviewed-By: Hongren Zheng <i@zenithal.me>
Link: https://lore.kernel.org/r/20230503173622.1072787-1-ukleinek@debian.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The channel's rpmsg object allows new invocations to be made. After old
invocations are already interrupted, the driver shouldn't try to invoke
anymore. Invalidating the rpmsg at the end of the driver removal
function makes it easy to cause a race condition in userspace. Even
closing a file descriptor before the driver finishes its cleanup can
cause an invocation via fastrpc_release_current_dsp_process() and
subsequent timeout.
Invalidate the channel before the invocations are interrupted to make
sure that no invocations can be created to hang after the device closes.
Fixes: c68cfb718c ("misc: fastrpc: Add support for context Invoke method")
Cc: stable <stable@kernel.org>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523152550.438363-5-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value is initialized as -1, or -EPERM. The completion of an
invocation implies that the return value is set appropriately, but
"Permission denied" does not accurately describe the outcome of the
invocation. Set the invocation's return value to a more appropriate
"Broken pipe", as the cleanup breaks the driver's connection with rpmsg.
Fixes: c68cfb718c ("misc: fastrpc: Add support for context Invoke method")
Cc: stable <stable@kernel.org>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523152550.438363-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The userspace map request for remote heap allocates CMA memory.
The ownership of this memory needs to be reassigned to proper
owners to allow access from the protection domain running on
DSP. This reassigning of ownership is not correct if done for
any other supported flags.
When any other flag is requested from userspace, fastrpc is
trying to reassign the ownership of memory and this reassignment
is getting skipped for remote heap request which is incorrect.
Add proper flag check to reassign the memory only if remote heap
is requested.
Fixes: 532ad70c6d ("misc: fastrpc: Add mmap request assigning for static PD pool")
Cc: stable <stable@kernel.org>
Tested-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523152550.438363-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a map request is made with securemap attribute, the memory
ownership needs to be reassigned to new VMID to allow access
from protection domain. Currently only DSP VMID is passed to
the reassign call which is incorrect as only a combination of
HLOS and DSP VMID is allowed for memory ownership reassignment
and passing only DSP VMID will cause assign call failure.
Also pass proper restoring permissions to HLOS as the source
permission will now carry both HLOS and DSP VMID permission.
Change is also made to get valid physical address from
scatter/gather for this allocation request.
Fixes: e90d911906 ("misc: fastrpc: Add support to secure memory map")
Cc: stable <stable@kernel.org>
Tested-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523152550.438363-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __mei_cl_recv and __mei_cl_send accepts u8 buffer.
Fix buffer type from char to u8.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20230522101210.2207395-2-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cldev cannot be NULL when derived with to_mei_cl_device().
Drop useless NULL-checks.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20230522101210.2207395-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230516110038.2413224-18-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
While touching these drivers, fix alignment in apds990x.c and bh1770glc.c.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20230517220135.170379-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a compatible string for MediaTek Helio X10 MT6795: this SoC uses
the same DSI PHY as MT8173.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230412112739.160376-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This smartphone uses the Helio X10 standard MT6331+MT6332 combo PMICs:
include the mt6331 devicetree and add the required interrupt.
Note that despite there being two interrupts, one for MT6331 and one
for MT6332, in configurations using the companion PMIC, the interrupt
of the latter fires for both events on MT6331 and for ones on MT6332,
while the interrupt for the main PMIC fires only for events of the
main PMIC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-25-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT6331 is the primary PMIC for the MediaTek Helio X10 MT6795 smartphone
platforms: add a devicetree describing its regulators, Real Time Clock
and PMIC-keys.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-24-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add nodes for the multimedia IOMMU and its LARBs: this includes all but
the MJC LARB, which cannot currently be used and will be added later.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-19-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use C99 array initializer syntax for consistency with other array
initializers around it and to eliminate a sparse warning:
drivers/accessibility/speakup/main.c:1290:26: sparse: warning: obsolete array initializer, use C99 syntax
Fixes: f43241aafe ("accessibility: speakup: Specify spk_vars among module parameters")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mushahid Hussain <mushi.shar@gmail.com>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: speakup@linux-speakup.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20230501001617.9152-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns:
arch/x86/lib/csum-partial_64.c:74:20: error: variable 'result' is uninitialized when used here [-Werror,-Wuninitialized]
return csum_tail(result, temp64, odd);
^~~~~~
arch/x86/lib/csum-partial_64.c:48:22: note: initialize the variable 'result' to silence this warning
unsigned odd, result;
^
= 0
1 error generated.
The only initialization and uses of result in csum_partial() were moved
into csum_tail() but result is still being passed by value to
csum_tail() (clang's -Wuninitialized does not do interprocedural
analysis to realize that result is always assigned in csum_tail()
however). Sink the declaration of result into csum_tail() to clear up
the warning.
Closes: https://lore.kernel.org/202305262039.3HUYjWJk-lkp@intel.com/
Fixes: 688eb8191b ("x86/csum: Improve performance of `csum_partial`")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20230526-csum_partial-wuninitialized-v1-1-ebc0108dcec1%40kernel.org