The kernel test robot reported a compile-time error regarding the
FIELD_PREP() value being too large for the TRANS_DUAL_QUAD field:
error: FIELD_PREP: value too large for the field
note: in expansion of macro 'TRANS_DUAL_QUAD'
tc |= TRANS_DUAL_QUAD(ffs(op->data.buswidth) - 1);
This occurs because TRANS_DUAL_QUAD is defined as a 2-bit field, and
GCC's static analysis cannot deduce that `ffs(op->data.buswidth) - 1`
will strictly fall within the 0~3 range. Although the SPI framework
guarantees that `op->data.buswidth` is valid at runtime (e.g., 1, 2,
4, 8), an explicit bounds check is necessary to satisfy the compiler.
To resolve the build warning, introduce a safe fallback mechanism.
If an unexpected buswidth is encountered, the driver will trigger
a WARN_ON_ONCE to leave a trace and fall back to width_code = 0
(standard 1-bit SPI mode). This approach guarantees predictable
hardware behavior.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202602140738.P7ZozxzI-lkp@intel.com/
Suggested-by: Pei Xiao <xiaopei01@kylinos.cn>
Signed-off-by: CL Wang <cl634@andestech.com>
Link: https://patch.msgid.link/20260303024737.1791196-1-cl634@andestech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIOs with "gpio" suffix were long time ago deprecated, thus
"reset-gpios" should be used. Linux kernel supports both, thus this
only documents desired choice of ABI.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260311153548.94265-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In update_fdt_memmap() an update_fdt() the fdt values should be
of the fd32_t and fdt64_t types. Make the relevant changes to
remove the following sparse warnings:
drivers/firmware/efi/libstub/fdt.c:97:19: warning: incorrect type in assignment (different base types)
drivers/firmware/efi/libstub/fdt.c:97:19: expected unsigned long long [usertype] fdt_val64
drivers/firmware/efi/libstub/fdt.c:97:19: got restricted __be64 [usertype]
drivers/firmware/efi/libstub/fdt.c:157:19: warning: incorrect type in assignment (different base types)
drivers/firmware/efi/libstub/fdt.c:157:19: expected unsigned long long [usertype] fdt_val64
drivers/firmware/efi/libstub/fdt.c:157:19: got restricted __be64 [usertype]
drivers/firmware/efi/libstub/fdt.c:163:19: warning: incorrect type in assignment (different base types)
drivers/firmware/efi/libstub/fdt.c:163:19: expected unsigned int [usertype] fdt_val32
drivers/firmware/efi/libstub/fdt.c:163:19: got restricted __be32 [usertype]
drivers/firmware/efi/libstub/fdt.c:169:19: warning: incorrect type in assignment (different base types)
drivers/firmware/efi/libstub/fdt.c:169:19: expected unsigned int [addressable] [usertype] fdt_val32
drivers/firmware/efi/libstub/fdt.c:169:19: got restricted __be32 [usertype]
drivers/firmware/efi/libstub/fdt.c:175:19: warning: incorrect type in assignment (different base types)
drivers/firmware/efi/libstub/fdt.c:175:19: expected unsigned int [addressable] [usertype] fdt_val32
drivers/firmware/efi/libstub/fdt.c:175:19: got restricted __be32 [usertype]
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
efi_range_is_wc() has no callers, so remove it.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The AMD PMF driver provides realtime column utilization (npu_busy)
metrics for the NPU. Extend the DRM_IOCTL_AMDXDNA_GET_INFO sensor
query to expose these metrics to userspace.
Add AMDXDNA_SENSOR_TYPE_COLUMN_UTILIZATION to the sensor type enum
and update aie2_get_sensors() to return both the total power and up
to 8 column utilization sensors if the user buffer permits.
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Lizhi Hou <lizhi.hou@amd.com>
[lizhi: support legacy tool which uses small buffer. checkpatch cleanup]
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260311171842.473453-1-lizhi.hou@amd.com
The AMD PMF driver provides an interface to obtain realtime power
estimates for the NPU. Expose this information to userspace through a
new DRM_IOCTL_AMDXDNA_GET_INFO parameter, allowing applications to query
the current NPU power level.
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
(Update comment to indicate power and utilization)
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260228061109.361239-2-superm1@kernel.org
The amdxdna driver uses amd_pmf_get_npu_data() which is exported in the
AMD_PMF namespace. Import the AMD_PMF namespace.
Reviewed-by: Lizhi Hou <lizhi.hou@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20260301005028.367618-1-superm1@kernel.org
The function acpi_processor_cstate_first_run_checks() is currently called
only once during initialization in acpi_processor_register_idle_driver().
Since its execution is already limited by the caller's lifecycle, the
internal static 'first_run' variable is redundant and can be safely
removed.
Additionally, the current function name is no longer descriptive of its
behavior, so rename the function to acpi_processor_update_max_cstate()
to better reflect its actual purpose.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Link: https://patch.msgid.link/20260311065038.4151558-4-lihuisong@huawei.com
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_processor_cstate_first_run_checks() function, which updates
max_cstate on certain platforms, only needs to be executed once.
Move this call outside of the loop to avoid redundant executions.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Link: https://patch.msgid.link/20260311065038.4151558-3-lihuisong@huawei.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function acpi_processor_cstate_first_run_checks() is responsible
for updating max_cstate and performing initial hardware validation.
Currently, this function is invoked within acpi_processor_power_init().
However, the initialization flow already ensures this is called during
acpi_processor_register_idle_driver(). Therefore, the call in
acpi_processor_power_init() is redundant and effectively performs no work,
so remove it.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Link: https://patch.msgid.link/20260311065038.4151558-2-lihuisong@huawei.com
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A recently added quirk does not fit in the left column of the table,
so it all has to be reformatted and realigned.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid code duplication by extracting the logic for selection of the
correct PAT_PTA entry for a GT into function gt_pta_entry() and using
that function whenever necessary.
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Link: https://patch.msgid.link/20260303-pat-gt_pta_entry-v1-1-0dee8e1e7bd9@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
If discovery has failed for any reason (such as no support for a block)
then there is no need to unwind all the IP blocks in fini. In this
condition there can actually be failures during the unwind too.
Reset num_ip_blocks to zero during failure path and skip the unnecessary
cleanup path.
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit fae5984296)
Cc: stable@vger.kernel.org
Error handling path should unreserve bo then return failed.
Fixes: 305cd109b7 ("drm/amdkfd: Validate user queue update")
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Alex Sierra <alex.sierra@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit c24afed7de)
[WHY]
On DCN21, dccg2_init() is called in dcn10_init_hw() before
bios_golden_init(). During S0i3 resume, BIOS sets MICROSECOND_TIME_BASE_DIV
to 0x00120464 as a marker. dccg2_init() overwrites this to 0x00120264,
causing dcn21_s0i3_golden_init_wa() to misdetect the state and skip golden
init.
Eventually during the resume sequence, a flip timeout occurs.
[HOW]
Skip DCCG on dccg2_is_s0i3_golden_init_wa_done() on DCN21.
Fixes: 4c595e7511 ("drm/amd/display: Migrate DCCG registers access from hwseq to dccg component.")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit c61eda4343)
Commit 4c595e7511 ("drm/amd/display: Migrate DCCG registers access
from hwseq to dccg component.") moved register writes from hwseq to
dccg2_*() functions but did not add the registers to the DCCG register
list macros. The struct fields default to 0, so REG_WRITE() targets
MMIO offset 0, causing a GPU hang on resume (seen on DCN21/DCN30
during IGT kms_cursor_crc@cursor-suspend).
Add
- MICROSECOND_TIME_BASE_DIV
- MILLISECOND_TIME_BASE_DIV
- DCCG_GATE_DISABLE_CNTL
- DCCG_GATE_DISABLE_CNTL2
- DC_MEM_GLOBAL_PWR_REQ_CNTL
to macros in dcn20_dccg.h, dcn301_dccg.h, dcn31_dccg.h, and dcn314_dccg.h.
Fixes: 4c595e7511 ("drm/amd/display: Migrate DCCG registers access from hwseq to dccg component.")
Reported-by: Rafael Passos <rafael@rcpassos.me>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e6e2b956fc)
It turned out that protecting the status of each bo_va with a
spinlock was just hiding problems instead of solving them.
Revert the whole approach, add a separate stats_lock and lockdep
assertions that the correct reservation lock is held all over the place.
This not only allows for better checks if a state transition is properly
protected by a lock, but also switching back to using list macros to
iterate over the state of lists protected by the dma_resv lock of the
root PD.
v2: re-add missing check
v3: split into two patches
v4: re-apply by fixing holding the VM lock at the right places.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sunil Khatri <sunil.khatri@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If discovery has failed for any reason (such as no support for a block)
then there is no need to unwind all the IP blocks in fini. In this
condition there can actually be failures during the unwind too.
Reset num_ip_blocks to zero during failure path and skip the unnecessary
cleanup path.
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix XGMI max bitrate/width reporting on SMUv13.0.12 SOCs. The data
format got changed when moved to static table from dynamic metrics
table.
Fixes: 1bec2f2707 ("drm/amd/pm: Fetch SMUv13.0.12 xgmi max speed/width")
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The mes.fw[] is per-pipe resource shared accross xcc inst.
And enlarge hung_queue array to max inst_pipes.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct the base addr value shown on sysfs with ignore reg_base_64,
since the base_addr value have been over write when discovery_init.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable to print RLC v2_5 related firmware information by default.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calculate sdma instance number according to xcc_mask and
num_inst_per_xcc, and correct adev->sdma.sdma_mask according
to totally sdma instance number.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UMC node_inst_num can exceed 32, causing
(1 << node_inst_num) to shift a 32-bit int
out of bounds
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For MP0 15.0.8, IMU ucode is part of IFWI and ASP would load it by default.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update GFX CGCG flags and fix num_xcc assignment
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Return false from soc_v1_0_reset_on_init as psp is loaded with ifwi and
sol register will be non zero on first load itself
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
IH v7_1 changes the offsets of some registers relative to
IH v7_0. Introduce IH v7_1-specific register access
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If DF function not initialized, NULL pointer issue
will happen on soc24.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On some hardware configuration, sriov guests
cannot access mm_index and mm_data. Update the
IPD table via memcpy in these cases
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement a driver path to read the IP discovery
binary offset and size from DRIVER_SCRATCH registers
BIOS signals usage by setting a feature flag that
instructs the driver to use this method. Otherwise,
fallback to legacy approach.
v2: Simplify discovery offset/size retrieval in
get_tmr_info
v3: Update get_tmr_info to cover discovery offset
and size retrieval for both bare-metal and sriov
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use an common function to check the validation of discovery table.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support for new IP discovery binary header version 2.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Error handling path should unreserve bo then return failed.
Fixes: 305cd109b7 ("drm/amdkfd: Validate user queue update")
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Alex Sierra <alex.sierra@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following updates:
- [FW Promotion] Release 0.1.50.0
- Sync DCN42 with DC 3.2.373
- Add DML support for dcn42
- Enable dcn42 DC clk_mgr
- Clean up unused code
- Add back missing memory type in array
- Fix compile warnings in dml2_0
- Check for S0i3 to be done before DCCG init on DCN21
- Add documentation and cleanup DMUB HW lock manager
- Add new types to replay config
- Fix HWSS v3 fast path determination
- Add missing DCCG register entries for DCN20-DCN316
- Add ESD detection for replay recovery
- Update underflow detection
- Add COLOR_ENCODING/COLOR_RANGE to overlay planes
- Add NV12/P010 formats to primary plane
- Set chroma taps to 1 if luma taps are 1
- Add min clock init for DML21 mode programming
- Return early from vesa replay enable function
- Clean up NULL pointer warnings in dml2
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch provides a bulk merge to align driver
support for DCN42 with Display Core version 3.2.373.
It includes upgrade for:
- clk_mgr
- dml2/dml21
- optc
- hubp
- mpc
- optc
- hwseq
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DML support for DCN 4.2
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for DCN 4.2 clock manager.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Silence warning by cleaning up unused code.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Clay King <clayking@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Add back some missing memory type in window_memory_type.
It should be aligned with enum dmub_window_id.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>