Afaict there's no need to (incompletely) iterate the
MEM_UOPS_RETIRED.* umask state.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1338884803.28282.153.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implement rudimentary IVB perf support. The SDM states its identical
to SNB with exception of the exact event tables, but a quick look
suggests they're similar enough.
Also mark SNB-EP as broken for now.
Requested-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1338884803.28282.153.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that there's finally a chip with working PEBS (IvyBridge), we can
enable the hardware and implement cycles:p for SNB/IVB.
Cc: Stephane Eranian <eranian@google.com>
Requested-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1338884803.28282.153.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Zheng Yan reported that event group validation can wreck event state
when Intel extra_reg allocation changes event state.
Validation shouldn't change any persistent state. Cloning events in
validate_{event,group}() isn't really pretty either, so add a few
special cases to avoid modifying the event state.
The code is restructured to minimize the special case impact.
Reported-by: Zheng Yan <zheng.z.yan@linux.intel.com>
Acked-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1338903031.28282.175.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add some code to validate assumptions we're making and output
warnings if they are not.
If this trigger we want to know about it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alex Shi <lkml.alex@gmail.com>
Link: http://lkml.kernel.org/n/tip-6uc3wk5s9udxtdl9cnku0vtt@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Often when we run into mis-shapen topologies the balance iteration
fails to update the cpu power properly and we'll end up in /0 traps.
Always initialize the cpu-power to a semi-sane value so that we can
at least boot the machine, even if the load-balancer might not
function correctly.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-3lbhyj25sr169ha7z3qht5na@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Weird topologies can lead to asymmetric domain setups. This needs
further consideration since these setups are typically non-minimal
too.
For now, make it work by adding an extra mask selecting which CPUs
are allowed to iterate up.
The topology that triggered it is the one from David Rientjes:
10 20 20 30
20 10 20 20
20 20 10 20
30 20 20 10
resulting in boxes that wouldn't even boot.
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-3p86l9cuaqnxz7uxsojmz5rm@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Roland Dreier reported spurious, hard to trigger lockdep warnings
within the scheduler - without any real lockup.
This bit gives us the right clue:
> [89945.640512] [<ffffffff8103fa1a>] double_lock_balance+0x5a/0x90
> [89945.640568] [<ffffffff8104c546>] push_rt_task+0xc6/0x290
if you look at that code you'll find the double_lock_balance() in
question is the one in find_lock_lowest_rq() [yay for inlining].
Now find_lock_lowest_rq() has a bug.. it fails to use
double_unlock_balance() in one exit path, if this results in a retry in
push_rt_task() we'll call double_lock_balance() again, at which point
we'll run into said lockdep confusion.
Reported-by: Roland Dreier <roland@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1337282386.4281.77.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit cb83b629b ("sched/numa: Rewrite the CONFIG_NUMA sched
domain support") removed the NODE sched domain and started checking
if the node distance in SLIT table is farther than REMOTE_DISTANCE,
if so, it will lose the load balance chance at exec/fork/wake_affine
points.
But actually, even the node distance is farther than REMOTE_DISTANCE.
Modern CPUs also has QPI like connections, which ensures that memory
access is not too slow between nodes. So the above change in behavior
on NUMA machine causes a performance regression on various benchmarks:
hackbench, tbench, netperf, oltp, etc.
This patch will recover the scheduler behavior to old mode on all my
Intel platforms: NHM EP/EX, WSM EP, SNB EP/EP4S, and thus fixes the
perfromance regressions. (all of them just have 2 kinds distance, 10, 21)
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1338965571-9812-1-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 316ad24830 ("sched/x86: Rewrite set_cpu_sibling_map()")
broke the booted_cores accounting.
The problem is that the booted_cores accounting needs all the
sibling links set up. So restore the second loop and add a comment as
to why its needed.
On qemu booted with -smp sockets=1,cores=2,threads=2;
Before:
$ grep cores /proc/cpuinfo
cpu cores : 2
cpu cores : 1
cpu cores : 4
cpu cores : 3
With the patch:
$ grep cores /proc/cpuinfo
cpu cores : 2
cpu cores : 2
cpu cores : 2
cpu cores : 2
Reported-by: Prarit Bhargava <prarit@redhat.com>
Reported-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120531073738.GH7511@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since Henrik's autoloading changes, the proper macro for device
entry is MT_USB_DEVICE().
Reported-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ceph_con_revoke_message() is passed both a message and a ceph
connection. A ceph_msg allocated for incoming messages on a
connection always has a pointer to that connection, so there's no
need to provide the connection when revoking such a message.
Note that the existing logic does not preclude the message supplied
being a null/bogus message pointer. The only user of this interface
is the OSD client, and the only value an osd client passes is a
request's r_reply field. That is always non-null (except briefly in
an error path in ceph_osdc_alloc_request(), and that drops the
only reference so the request won't ever have a reply to revoke).
So we can safely assume the passed-in message is non-null, but add a
BUG_ON() to make it very obvious we are imposing this restriction.
Rename the function ceph_msg_revoke_incoming() to reflect that it is
really an operation on an incoming message.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
ceph_con_revoke() is passed both a message and a ceph connection.
Now that any message associated with a connection holds a pointer
to that connection, there's no need to provide the connection when
revoking a message.
This has the added benefit of precluding the possibility of the
providing the wrong connection pointer. If the message's connection
pointer is null, it is not being tracked by any connection, so
revoking it is a no-op. This is supported as a convenience for
upper layers, so they can revoke a message that is not actually
"in flight."
Rename the function ceph_msg_revoke() to reflect that it is really
an operation on a message, not a connection.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
There are essentially two types of ceph messages: incoming and
outgoing. Outgoing messages are always allocated via ceph_msg_new(),
and at the time of their allocation they are not associated with any
particular connection. Incoming messages are always allocated via
ceph_con_in_msg_alloc(), and they are initially associated with the
connection from which incoming data will be placed into the message.
When an outgoing message gets sent, it becomes associated with a
connection and remains that way until the message is successfully
sent. The association of an incoming message goes away at the point
it is sent to an upper layer via a con->ops->dispatch method.
This patch implements reference counting for all ceph messages, such
that every message holds a reference (and a pointer) to a connection
if and only if it is associated with that connection (as described
above).
For background, here is an explanation of the ceph message
lifecycle, emphasizing when an association exists between a message
and a connection.
Outgoing Messages
An outgoing message is "owned" by its allocator, from the time it is
allocated in ceph_msg_new() up to the point it gets queued for
sending in ceph_con_send(). Prior to that point the message's
msg->con pointer is null; at the point it is queued for sending its
message pointer is assigned to refer to the connection. At that
time the message is inserted into a connection's out_queue list.
When a message on the out_queue list has been sent to the socket
layer to be put on the wire, it is transferred out of that list and
into the connection's out_sent list. At that point it is still owned
by the connection, and will remain so until an acknowledgement is
received from the recipient that indicates the message was
successfully transferred. When such an acknowledgement is received
(in process_ack()), the message is removed from its list (in
ceph_msg_remove()), at which point it is no longer associated with
the connection.
So basically, any time a message is on one of a connection's lists,
it is associated with that connection. Reference counting outgoing
messages can thus be done at the points a message is added to the
out_queue (in ceph_con_send()) and the point it is removed from
either its two lists (in ceph_msg_remove())--at which point its
connection pointer becomes null.
Incoming Messages
When an incoming message on a connection is getting read (in
read_partial_message()) and there is no message in con->in_msg,
a new one is allocated using ceph_con_in_msg_alloc(). At that
point the message is associated with the connection. Once that
message has been completely and successfully read, it is passed to
upper layer code using the connection's con->ops->dispatch method.
At that point the association between the message and the connection
no longer exists.
Reference counting of connections for incoming messages can be done
by taking a reference to the connection when the message gets
allocated, and releasing that reference when it gets handed off
using the dispatch method.
We should never fail to get a connection reference for a
message--the since the caller should already hold one.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
When a ceph message is queued for sending it is placed on a list of
pending messages (ceph_connection->out_queue). When they are
actually sent over the wire, they are moved from that list to
another (ceph_connection->out_sent). When acknowledgement for the
message is received, it is removed from the sent messages list.
During that entire time the message is "in the possession" of a
single ceph connection. Keep track of that connection in the
message. This will be used in the next patch (and is a helpful
bit of information for debugging anyway).
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
The function ceph_alloc_msg() is only used to allocate a message
that will be assigned to a connection's in_msg pointer. Rename the
function so this implied usage is more clear.
In addition, make that assignment inside the function (again, since
that's precisely what it's intended to be used for). This allows us
to return what is now provided via the passed-in address of a "skip"
variable. The return type is now Boolean to be explicit that there
are only two possible outcomes.
Make sure the result of an ->alloc_msg method call always sets the
value of *skip properly.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Move the initialization of a ceph connection's private pointer,
operations vector pointer, and peer name information into
ceph_con_init(). Rearrange the arguments so the connection pointer
is first. Hide the byte-swapping of the peer entity number inside
ceph_con_init()
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Hold off initializing a monitor client's connection until just
before it gets opened for use.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
All references to the embedded ceph_connection come from the msgr
workqueue, which is drained prior to mon_client destruction. That
means we can ignore con refcounting entirely.
Signed-off-by: Sage Weil <sage@newdream.net>
Reviewed-by: Alex Elder <elder@inktank.com>
A monitor client has a pointer to a ceph connection structure in it.
This is the only one of the three ceph client types that do it this
way; the OSD and MDS clients embed the connection into their main
structures. There is always exactly one ceph connection for a
monitor client, so there is no need to allocate it separate from the
monitor client structure.
So switch the ceph_mon_client structure to embed its
ceph_connection structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
There were a few direct calls to ceph_con_{get,put}() instead of the con
ops from osd_client.c. This is a bug since those ops aren't defined to
be ceph_con_get/put.
This breaks refcounting on the ceph_osd structs that contain the
ceph_connections, and could lead to all manner of strangeness.
The purpose of the ->get and ->put methods in a ceph connection are
to allow the connection to indicate it has a reference to something
external to the messaging system, *not* to indicate something
external has a reference to the connection.
[elder@inktank.com: added that last sentence]
Signed-off-by: Sage Weil <sage@newdream.net>
Reviewed-by: Alex Elder <elder@inktank.com>
In ceph_osdc_release_request(), a reference to the r_reply message
is dropped. But just after that, that same message is revoked if it
was in use to receive an incoming reply. Reorder these so we are
sure we hold a reference until we're actually done with the message.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Sparse complains about this because:
drivers/block/rbd.c:996:20: warning: cast to restricted __le32
drivers/block/rbd.c:996:20: warning: cast from restricted __le16
These are set in osd_req_encode_op() and they are le16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Add support for a Novatek touchscreen panel as a generic HID multitouch
panel.
Signed-off-by: Austin Hendrix <ahendrix@willowgarage.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The definition of DWC3_DCTL_HIRD_THRES macro is
completely wrong. It will only work for when we
want to read the register's contents for that bitfield.
Change the macro so that it can be used to writing to
the register, and when we need to read, we can add
extra right shift of 24 bits.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
[ balbi@ti.com: add a commit log ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
When mmc_host is not spi mode, mmc/sd is doing mmc_deselect_cards().
mmc_deselect_cards could be returned error.
If returned error, we can know something wrong when enter suspend.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit fa550189 (mmc: core: Prevent eMMC VCC supply to be cut from late init)
slightly affected timings for how things are done for the omap MMC driver
causing the MMC cards not getting detected any longer.
Turns out this was caused by buggy reg_shift initialization in the omap
MMC driver that was happening after mmc_add_host() was being called.
Fix this by initializing reg_shift before mmc_add_host() is called.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit b01a4f1c (mmc: omap: convert to per instance workqueue) initializes
the workqueue too late causing the following:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.4.0-08218-gb48b2c3 #158)
PC is at __queue_work+0x8/0x46c
LR is at queue_work_on+0x38/0x40
pc : [<c005bb4c>] lr : [<c005c00c>] psr: 60000193
sp : c0691e1c ip : 00000000 fp : c07374ac
r10: c7aae400 r9 : c0395700 r8 : 00000100
r7 : c0691e70 r6 : 00000000 r5 : 00000000 r4 : c7aae440
r3 : 00000001 r2 : c7aae440 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 00c5387d Table: 80004000 DAC: 00000017
Process swapper/0 (pid: 0, stack limit = 0xc06902f8)
Stack: (0xc0691e1c to 0xc0692000)
Fix this by initializing the workqueue before mmc_omap_remove_slot()
get called. Tested on n770, looks like n800 at least still has some
other issue with MMC.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit b6e0703b (mmc: omap: make it behave well as a module) made some
__devinit changes but missed one function causing a section warning:
WARNING: vmlinux.o(.devinit.text+0x8604): Section mismatch in reference
from the function mmc_omap_probe)
The function __devinit mmc_omap_probe() references a function
__init mmc_omap_new_slot().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case of "host->bus_hz < slot->clock", divider value is
miscalculated. And clock divider register value is multiple of 2. If
calculated divider value is odd number, result can be over-clocking.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Setting host->data to NULL is incorrect sequence in
dw_mci_command_complete. This early setting makes the skip of
dma_unmap_sg in dw_mci_dma_cleanup.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
IDMAC may not be cleaned in driver probe if it has been already used in
boot time. So IDMAC needs sw reset newly. And DMA interface reset
precedes the internal DMAC reset. Additionally SDMMC_IDMAC_SWRESET is
replaced with magic code.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
DTO interrupt can be later than transmit interrupt(IDMAC) in case of
write. Current handling of IDMAC interrupt sets EVENT_DATA_COMPLETE as
well as EVENT_XFER_COMPLETE regardless of DTO rising. This makes the
current request finish in tasklet and permits the next request even
though current data transfer is still in progress. As a result, sequence
is broken and lock-up happens. Setting EVENT_DATA_COMPLETE is not proper
after IDMAC interrupt. It should be taken after DTO interrupt is
generated.
Reported-by: Dmitry Shmidt <dimitrysh@android.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Hyeonsu Kim <hyeonsu.kim@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO_CCCR_IF[1:0] in SDIO card is used for card data bus width
setting as below:
00b: 1-bit bus
01b: Reserved
10b: 4-bit bus
11b: 8-bit bus (only for embedded SDIO)
And sdio_enable_wide is for setting data bus width as 4-bit.
But currently, it first reads the register, second OR' 1b with
SDIO_CCCR_IF[1], and then writes it back.
As we can see, this is based on such assumption that the
SDIO_CCCR_IF[0] is always 0. Apparently, this is not right.
Signed-off-by: Yong Ding <yongd@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The use of DMA slave config operation requires that the burst size
(aka chunk size) is specified through this interface.
Modify atmel-mci slave driver to use this specification on its side.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Alex says:
"Changes this time include:
- Generalize KVM_GUEST support to overall ePAPR code
- Fix reset for Book3S HV
- Fix machine check deferral when CONFIG_KVM_GUEST=y
- Add support for BookE register DECAR"
* 'for-upstream' of git://github.com/agraf/linux-2.6:
KVM: PPC: Not optimizing MSR_CE and MSR_ME with paravirt.
KVM: PPC: booke: Added DECAR support
KVM: PPC: Book3S HV: Make the guest hash table size configurable
KVM: PPC: Factor out guest epapr initialization
Signed-off-by: Avi Kivity <avi@redhat.com>
I see this in 3.5-rc1:
arch/x86/kvm/mmu.c: In function ‘kvm_test_age_rmapp’:
arch/x86/kvm/mmu.c:1271: warning: ‘iter.desc’ may be used uninitialized in this function
The line in question was introduced by commit
1e3f42f03c
static int kvm_test_age_rmapp(struct kvm *kvm, unsigned long *rmapp,
unsigned long data)
{
- u64 *spte;
+ u64 *sptep;
+ struct rmap_iterator iter; <- line 1271
int young = 0;
/*
The reason I think is that the compiler assumes that
the rmap value could be 0, so
static u64 *rmap_get_first(unsigned long rmap, struct rmap_iterator
*iter)
{
if (!rmap)
return NULL;
if (!(rmap & 1)) {
iter->desc = NULL;
return (u64 *)rmap;
}
iter->desc = (struct pte_list_desc *)(rmap & ~1ul);
iter->pos = 0;
return iter->desc->sptes[iter->pos];
}
will not initialize iter.desc, but the compiler isn't
smart enough to see that
for (sptep = rmap_get_first(*rmapp, &iter); sptep;
sptep = rmap_get_next(&iter)) {
will immediately exit in this case.
I checked by adding
if (!*rmapp)
goto out;
on top which is clearly equivalent but disables the warning.
This patch uses uninitialized_var to disable the warning without
increasing code size.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduces a couple of print functions, which are essentially wrappers
around standard printk functions, with a KVM: prefix.
Functions introduced or modified are:
- kvm_err(fmt, ...)
- kvm_info(fmt, ...)
- kvm_debug(fmt, ...)
- kvm_pr_unimpl(fmt, ...)
- pr_unimpl(vcpu, fmt, ...) -> vcpu_unimpl(vcpu, fmt, ...)
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Gilad reported at
http://lkml.kernel.org/r/1336056962-10465-2-git-send-email-gilad@benyossef.com
"Current timer code fails to correctly return a value meaning that
there is no future timer event, with the result that the timer keeps
getting re-armed in HZ one shot mode even when we could turn it off,
generating unneeded interrupts.
What is happening is that when __next_timer_interrupt() wishes
to return a value that signifies "there is no future timer
event", it returns (base->timer_jiffies + NEXT_TIMER_MAX_DELTA).
However, the code in tick_nohz_stop_sched_tick(), which called
__next_timer_interrupt() via get_next_timer_interrupt(),
compares the return value to (last_jiffies + NEXT_TIMER_MAX_DELTA)
to see if the timer needs to be re-armed.
base->timer_jiffies != last_jiffies and so tick_nohz_stop_sched_tick()
interperts the return value as indication that there is a distant
future event 12 days from now and programs the timer to fire next
after KTIME_MAX nsecs instead of avoiding to arm it. This ends up
causing a needless interrupt once every KTIME_MAX nsecs."
Fix this by using the new active timer accounting. This avoids scans
when no active timer is enqueued completely, so we don't have to rely
on base->timer_next and base->timer_jiffies anymore.
Reported-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120525214819.317535385@linutronix.de
The code in get_next_timer_interrupt() is suboptimal as it has to run
through the cascade to find the next expiring timer. On a completely
idle core we should only do that when there is an active timer
enqueued and base->next_timer does not give us a fast answer.
Add accounting of the active timers to the now consolidated
attach/detach code. I deliberately avoided sanity checks because the
code is fully symetric and any fiddling with timers w/o using the API
functions will lead to cute explosions anyway. ulong is big enough
even on 32bit and if we really run into the situation to have more
than 1<<32 timers enqueued there, then we are definitely not in a
state to go idle and run through that code.
This allows us to fix another shortcoming of get_next_timer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120525214819.236377028@linutronix.de
Another bunch of mindlessly copied code. All callers of
internal_add_timer() except the recascading code updates
base->next_timer.
Move this into internal_add_timer() and let the cascading code call
__internal_add_timer().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120525214819.189946224@linutronix.de
Most callers of detach_timer() have the same pattern around
them. Check whether the timer is pending and eventually updating
base->next_timer.
Create detach_if_pending() and replace the duplicated code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20120525214819.131246037@linutronix.de
There's no need to declare the opmode ops
as extern since they're now dynamically
registered.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the RF config is done for all devices,
there's no need to keep a separate function
that is called for all devices, move it into
the general NIC config function.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>