Commit graph

321,296 commits

Author SHA1 Message Date
Anisse Astier
0586a11b5c rt2800: add chipset revision RT5390R support
About 70% of the chips with revision RT5390R initialize incorrectly, using
the auxiliary antenna instead of the main one. The net result is that
signal reception is very poor (no AP further than 1M).

This chipset differs from RT5390 and RT5390F by its support of hardware
antenna diversity. Therefore antenna selection should be done
differently, by disabling software features and previously selected
antenna.

This changeset does just that, and makes all RT5390R work properly.

This is based on Ralink's 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
driver.

Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:37:42 -04:00
Bala Shanmugam
218d2e26dc cfg80211: Validate legacy rateset.
Legacy rates are not validated while configuring
tx rateset using iw. So below cmd is accepted by nl80211.
sudo iw wlan2 set bitrates legacy-2.4 1 2 3

Validate legacy rates and return
error if any rate in the rateset is not valid.

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:37:41 -04:00
Wey-Yi Guy
0d8a0a1728 mac80211: declare ieee80211_ave_rssi as EXPORT
ieee80211_ave_rssi need to be declare as export for driver to use it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:37:41 -04:00
Javier Cardona
6ac95b5765 mac80211: fixup for mesh TSF adjustment latency in Toffset setpoint
The original patch defined the correction margin but did not apply it.

Signed-off-by: Shinichi Hotori <hotorinn@gmail.com>
Signed-off-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:37:41 -04:00
Zefir Kurtisi
b96f20b3af ath9k: extend DFS detector stats in dfs_debugfs
Extend debugfs entry for dfs_stats with DFS detection events
and shared pool statistics.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:37:41 -04:00
Michael Liang
2a5783b817 ath9k: don't strip mic on non-encrypted frames in tkip
Fix the following bug: in tkip mode, qos-null ps on/off packets
are dropped due to incorrect packet length so that ath9k softap
can't handle powersave state transition of peer STA correctly.

Signed-off-by: Michael Liang <mliang@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:33 -04:00
Larry Finger
e0602750ab rtlwifi: rtl8192se: Convert driver to use private dm struct
Convert driver to use private version of dig_t instead of global version.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:33 -04:00
Larry Finger
c21916ec4c rtlwifi: rtl8192de: Convert driver to use private dm structs
Convert driver to use the private dig_t instead of a global version.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:33 -04:00
Larry Finger
d10dc6d1b7 rtlwifi: rtl8192c: Convert driver to use private ps_t struct
Convert driver to use the private instead of global version.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:32 -04:00
Larry Finger
40332e5fd3 rtlwifi: rtl8192c: Convert driver to use private dm structs
Convert rtl8192c to use the dm_digtable struct in the common header file
instead of the global variable. Without this change, every instance of
rtl8192ce and rtl8192cu will be using the same global arrays.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:32 -04:00
Larry Finger
0985dfbc51 rtlwifi: Add dm structs to private structure
Add the dig_t and ps_t structures to the private variables.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:32 -04:00
Larry Finger
df37a0eccf rtlwifi: Move dig_t and ps_t structs
Move struct definitions for dig_t and ps_t to the common header file.

This move is needed to convert these structures from a "per-driver" to a
"per-interface" basis.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:32 -04:00
Felix Fietkau
8d1bd2afc5 ath9k_hw: increase tx abort timeout for half/quarter channels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:32 -04:00
Felix Fietkau
feb7bc9951 ath9k_hw: disable fast channel change when changing from/to half/quarter mode
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:31 -04:00
Felix Fietkau
e5d821a4ff ath9k_hw: disable Tx IQ calibration on half/quarter channels
It does not work properly and reduces throughput.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:31 -04:00
Felix Fietkau
7c5adc8d83 ath9k_hw: fix and clean up PHY activation delay
The delay calculation is the same for all chips, however some parts of the
code missed the extra delay factor for half/quarter.
Clean up the code and move the delay calculation to a common place.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:31 -04:00
Felix Fietkau
3e61d3f9b2 ath9k_hw: increase symbol overlap window for half/quarter channels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:31 -04:00
Felix Fietkau
08685ce30f ath9k_hw: set the PHY mode for half/quarter channels on AR9003
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:31 -04:00
Felix Fietkau
e115b7ec33 ath9k_hw: increase ACK timeout for half/quarter channels
For some reason the MAC timing is a bit off when waiting for ACKs, so add
some extra delay to the ACK timeout values. Significantly reduces the
number of retransmissions in my tests.
Also disable the 2.4 GHz ACK timeout workaround in half/quarter mode, it
is not required there.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:30 -04:00
Felix Fietkau
e88e486115 ath9k_hw: use standard SIFS time as reference for half/quarter channels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:30 -04:00
Rajkumar Manoharan
0466e2547d ath9k_hw: remove ATH_BTCOEX_CFG_MCI
AR9462 uses modified version of 3-Wire hw scheme for btcoex.
MCI itself is not a separate hw scheme but it aids to manage
multiple bt profiles. In ar9462, bt priority traffic is identified
by the number of bt profile types instead of gpio. So that this
patch removes MCI hw scheme.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:30 -04:00
Rajkumar Manoharan
ed2578cd24 ath9k: simplify beacon configuration for beaconing vifs
As of now beacon configuration is being called multiple times
in bss info change notification. This patch avoids multiple
configuration and make it simpler.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:30 -04:00
Zefir Kurtisi
78241bdcaf ath9k: make DFS detector pools SMP safe
This adds locking of the detector's shared pulse and PRI sequence
pools to enable multi-wiphy operation on SMP systems.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:30 -04:00
Felix Fietkau
7608f16573 libertas: add missing include
Without it, I get compile errors due to missing TASK_NORMAL,
TASK_UNINTERRUPTIBLE and schedule.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:29 -04:00
Helmut Schaa
88211021a6 rt2x00: Use GFP_KERNEL for rx buffer allocation on USB devices
Since the RX path on USB devices is handled in process context we can
use GFP_KERNEL for RX buffer allocation. This should reduce the
likelihood of allocation failures.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Tested-By: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:35:29 -04:00
Anisse Astier
0c0fdf6c80 rt2800: debugfs register access: BBP is 256 bytes big
We're already using BBP for values > 128. Make that explicit and allow
debugfs access.

Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:34:08 -04:00
Amitkumar Karwar
4daffe3543 mwifiex: add support for Marvell USB8797 chipset
This patch supports Avastar 88W8797 chipset with USB interface.

The corresponding firmware image file is located at:
"mrvl/usb8797_uapsta.bin"

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:34:08 -04:00
Thomas Pedersen
aee286c2cf mac80211: fix STA channel width field
According to IEEE 802.11 8.4.2.59, set the "STA channel width" bit to 0
if transmitting STA is using a 20mhz channel.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:34:07 -04:00
Thomas Pedersen
e76781e48f mac80211: don't set mesh peer ht caps if ht disabled
Blindly setting ht caps on a mesh peer's station entry would result in
MCS rates being used by the rate control algorithm even if no ht had
been configured. Fix this by checking the channel type before assigning
ht capabilites.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:34:07 -04:00
Thomas Pedersen
f743ff4907 mac80211: refactor mesh peer rate handling
To avoid passing supp_rates and basic_rates around all the time, just
derive these when needed in mesh_matches_local() and mesh_peer_init().

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:34:07 -04:00
Thomas Pedersen
54ab1ffb6c mac80211: refactor mesh peer initialization
This patch unifies the previous two paths toward mesh peer creation a
bit. It also fixes a bug where a peer's changing rates or HT mode
wouldn't register on leaving and then returning to the mesh with a sta
entry still present.

Also clean up locking and clear possibly stale ht cap.

Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:34:07 -04:00
Gabor Juhos
75acd5a82a ath9k: fix TX power reporting on AR9003 chips
The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.

The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.

On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:34:06 -04:00
Daniel Drake
488c3ee77e libertas CS: convert to asynchronous firmware loading
Signed-off-by: Daniel Drake <dsd@laptop.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:34:06 -04:00
Ben Greear
990e08a0f6 ath9k: Fix compile warnings when DEBUGFS is disabled.
This fixes two compile warnings, and removes a useless
cast when assigning the 'sc' variable.

Reported-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:28:34 -04:00
Ben Greear
8a690674e0 mac80211: Support on-channel scan option.
This based on an idea posted by Stanislaw Gruszka,
though I accept full blame for the implementation!

This has been tested with ath9k.

The idea is to let users scan on the current operating
channel without interrupting normal traffic more than
absolutely necessary (changing power level might reset
some hardware, for instance).

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:28:33 -04:00
Xose Vazquez Perez
e828b9fb4f wireless: rt2x00: rt2800usb more devices were identified
found in 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO

RT3070:
(0x2019,0x5201)  Planex Communications, Inc. RT8070
(0x7392,0x4085)  2L Central Europe BV 8070
7392 is Edimax

RT35xx:
(0x1690,0x0761) Askey
was Fujitsu Stylistic 550, but 1690 is Askey

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:28:33 -04:00
Felix Fietkau
20c8e8dc4e ath9k: add possible wiphy interface combinations
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:28:33 -04:00
Xose Vazquez Perez
63b3764111 wireless: rt2x00: rt2800usb add more devices ids
They were taken from ralink drivers:
2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO
2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO

0x1eda,0x2210 RT3070 Airties

0x083a,0xb511 RT3370 Panasonic
0x0471,0x20dd RT3370 Philips

0x1690,0x0764 RT35xx Askey
0x0df6,0x0065 RT35xx Sitecom
0x0df6,0x0066 RT35xx Sitecom
0x0df6,0x0068 RT35xx Sitecom

0x2001,0x3c1c RT5370 DLink
0x2001,0x3c1d RT5370 DLink

2001 is D-Link not Alpha

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 15:28:33 -04:00
Mark Brown
de050acaa1 ASoC: wm_hubs: Make sure we don't disable differential line outputs
While we need to clean up unused single ended line outputs we don't want
to do this if the outputs are in differential mode.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-23 20:20:00 +01:00
Mark Brown
82caa9780a regulator: wm831x-dcdc: Specify supply names
Allows hookup via normal consumer mechanisms.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-23 20:18:58 +01:00
Mark Brown
f1aba13fbd regulator: wm831x-ldo: Set up supply names
Allows hookup via normal consumer mechanisms.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-23 20:18:56 +01:00
Jiri Kosina
c6e6dc87b3 HID: hid-lg4ff: remove unused label in !LEDS_CLASS case
'out' label will be unused of CONFIG_LEDS_CLASS is unset.
Move it into conditional block.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-04-23 21:08:15 +02:00
Alan Stern
3d9545cc37 EHCI: maintain the ehci->command value properly
The ehci-hcd driver is a little haphazard about keeping track of the
state of the USBCMD register.  The ehci->command field is supposed to
hold the register's value (apart from a few special bits) at all
times, but it isn't maintained properly.

This patch (as1543) cleans up the situation.  It keeps ehci->command
up-to-date, and uses that value rather than reading the register from
the hardware whenever possible.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-04-23 12:05:44 -07:00
Kristoffer KARLSSON
dd7b10b30c ASoC: core: Add strobe control
Added support for a control that strobes a bit in
a register to high then back to low (or the inverse).

This is typically useful for hardware that requires
strobing a singe bit to trigger some functionality
and where exposing the bit in a normal single control
would require the user to first manually set then
again unset the bit again for the strobe to trigger.

Added convenience macro.

SOC_SINGLE_STROBE

Added accessor implementations.

snd_soc_get_strobe
snd_soc_put_strobe

Signed-off-by: Kristoffer KARLSSON <kristoffer.karlsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-23 20:05:06 +01:00
Kristoffer KARLSSON
4183eed288 ASoC: core: Add signed multi register control
Added control type that can span multiple consecutive codec registers
forming a single signed value in a MSB/LSB manner.
The control dynamically adjusts to the register word size configured
in driver.

Added convenience macro.

SOC_SINGLE_XR_SX

Added accessor implementations.

snd_soc_info_xr_sx
snd_soc_get_xr_sx
snd_soc_put_xr_sx

Signed-off-by: Kristoffer KARLSSON <kristoffer.karlsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-04-23 20:05:06 +01:00
Eldad Zack
6ead629b27 brcmsmac: "INTERMEDIATE but not AMPDU" only when tracing
I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU

From the code comment I understand that this something that can -
and does, quite frequently - happen.

Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 14:57:53 -04:00
Larry Finger
44eb65cfd8 rtlwifi: Fix oops on unload
Under some circumstances, a PCI-based driver reports the following OOPs:

Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>]  [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---

This oops is due to interrupts not being disabled in this particular path.

Reported-by: Dave Airlie <airlied@gmail.com>
Tested-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 14:57:53 -04:00
Stanislav Yakovlev
dd44731989 ipw2200: Fix race condition in the command completion acknowledge
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution.  Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:

Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.

After that you need to reload the driver to get it working again.

This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106

This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.

Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 14:57:49 -04:00
Stanislaw Gruszka
8db4c7e25d iwlwifi: do not nulify ctx->vif on reset
ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.

This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.

Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 14:56:12 -04:00
Gabor Juhos
83722bd4ae ath9k: fix tx power settings for AR9287
The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852
(ath9k_hw: Cleanup TX power calculation for AR9287).

Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.

Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.

Fix this by adding the missing call of the helper
function.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-23 14:56:11 -04:00