Newer devices use 32 bit for boost register,
set the correct value for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few places that iterate the wdev
list and assume wdev->netdev exists, check
there. The rfkill one has to be extended for
each non-netdev type later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since soon there will be virtual interfaces that
don't have a netdev, use the wdev identifier for
the API to retrieve interface data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some nl80211 callbacks will soon need the wdev instead
of the netdev, so add NL80211_FLAG_NEED_WDEV to allow
them to request that. Add NL80211_FLAG_NEED_WDEV_UP as
well which checks the netdev is UP if one exists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support a P2P device abstraction and
Bluetooth high-speed AMPs, we need to have a way
to identify virtual interfaces that don't have a
netdev associated.
Do this by adding a NL80211_ATTR_WDEV attribute
to identify a wdev which may or may not also be
a netdev.
To simplify things, use a 64-bit value with the
high 32 bits being the wiphy index for this new
wdev identifier in the nl80211 API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This API call was intended to be used by drivers
if they want to optimize key handling by removing
one key when another is added. Remove it since no
driver is using it. If needed, it can always be
added back.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_mlme_notify_scan_completed() iterates all
interfaces and doesn't need to assign anything to
the sdata variable before the loop.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AC parameters change, drivers might rely
on getting a bss_info_changed notification with
BSS_CHANGED_QOS in addition to the conf_tx call.
Always call the function when userspace updates
are made (in AP/GO modes) and also set the change
flag when updates were made by the AP (in managed
mode.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the new i.mx clock framework the i2c clock is registered as:
clk_register_clkdev(clk[i2c1_ipg_gate], NULL, "imx-i2c.0")
So we do not need to pass "i2c_clk" string and can use NULL instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
[wsa: rebased on top of the devm-conversion]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Patch shortens locals scope and adds missing braces. This is a diff
between v1 which was applied and v2 of patch "Bluetooth: btmrvl: Do
not send vendor events to bluetooth stack".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The 4430 and 4460 version of PandaBoard mostly the same with
exception at least in audio setup.
Use the omap4-panda.dts file as a base and only override the differences
between the revisions.
For audio it is the name of the sound card and the routing information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PandaBoard uses twl6040 connected via McPDM for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 SDP the audio setup includes the twl6040 codec and digital
microphones.
Since OMAP4 SDP is a reference board it has all possible audio interfaces
connected. This information is passed via the ti,audio-routing
property.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl6040 provides the audio and vibra support on OMAP4 SDP boards.
It is connected to i2c1 bus with 0x4b address.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMIC IP is used to connect up to 6 digital microphones directly to OMAP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM is used on OMAP4 based boards to communicate with an external audio
codec (twl6040).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure we prepare/unprepare the clock for the ST U300
I2C driver as is required by the clk API especially if you
use common clock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sys_nirq2 is used for twl6040, make sure the pin is configured
correctly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Indirect extent block is not accounted in i_blocks during allocation
thus we should not decrement i_blocks when we are freeing such block
during truncation.
Reported-by: Steve Nickel <snickel58@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Our emulation should be complete enough that we can emulate guests
while they are in big real mode, or in a mode transition that is not
virtualizable without unrestricted guest support.
Signed-off-by: Avi Kivity <avi@redhat.com>
Guest software doesn't actually depend on it, but vmx will refuse us
entry if we don't. Set the bit in both the cached segment and memory,
just to be nice.
Signed-off-by: Avi Kivity <avi@redhat.com>
Opcode C8.
Only ENTER with lexical nesting depth 0 is implemented, since others are
very rare. We'll fail emulation if nonzero lexical depth is used so data
is not corrupted.
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit 2adb5ad9fe removed ByteOp from MOVZX/MOVSX, replacing them by
SrcMem8, but neglected to fix the dependency in the emulation code
on ByteOp. This caused the instruction not to have any effect in
some circumstances.
Fix by replacing the check for ByteOp with the equivalent src.op_bytes == 1.
Signed-off-by: Avi Kivity <avi@redhat.com>
If we return early from an invalid guest state emulation loop, make
sure we return to it later if the guest state is still invalid.
Signed-off-by: Avi Kivity <avi@redhat.com>
Checking EFLAGS.IF is incorrect as we might be in interrupt shadow. If
that is the case, the main loop will notice that and not inject the interrupt,
causing an endless loop.
Fix by using vmx_interrupt_allowed() to check if we can inject an interrupt
instead.
Signed-off-by: Avi Kivity <avi@redhat.com>
We correctly default to SS when BP is used as a base in 16-bit address mode,
but we don't do that for 32-bit mode.
Fix by adjusting the default to SS when either ESP or EBP is used as the base
register.
Signed-off-by: Avi Kivity <avi@redhat.com>
memop is not initialized; this can lead to a two-byte operation
following a 4-byte operation to see garbage values. Usually
truncation fixes things fot us later on, but at least in one case
(call abs) it doesn't.
Fix by moving memop to the auto-initialized field area.
Signed-off-by: Avi Kivity <avi@redhat.com>
Otherwise, if the guest ends up looping, we never exit the srcu critical
section, which causes synchronize_srcu() to hang.
Signed-off-by: Avi Kivity <avi@redhat.com>
Some userspace (e.g. QEMU 1.1) munge the d and g bits of segment
descriptors, causing us not to recognize them as unusable segments
with emulate_invalid_guest_state=1. Relax the check by testing for
segment not present (a non-present segment cannot be usable).
Signed-off-by: Avi Kivity <avi@redhat.com>
The operand size for these instructions is 8 bytes in long mode, even without
a REX prefix. Set it explicitly.
Triggered while booting Linux with emulate_invalid_guest_state=1.
Signed-off-by: Avi Kivity <avi@redhat.com>
Opcode 0F A2.
Used by Linux during the mode change trampoline while in a state that is
not virtualizable on vmx without unrestricted_guest, so we need to emulate
it is emulate_invalid_guest_state=1.
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of getting an exact leaf, follow the spec and fall back to the last
main leaf instead. This lets us easily emulate the cpuid instruction in the
emulator.
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduce kvm_cpuid() to perform the leaf limit check and calculate
register values, and let kvm_emulate_cpuid() just handle reading and
writing the registers from/to the vcpu. This allows us to reuse
kvm_cpuid() in a context where directly reading and writing registers
is not desired.
Signed-off-by: Avi Kivity <avi@redhat.com>
In protected mode, the CPL is defined as the lower two bits of CS, as set by
the last far jump. But during the transition to protected mode, there is no
last far jump, so we need to return zero (the inherited real mode CPL).
Fix by reading CPL from the cache during the transition. This isn't 100%
correct since we don't set the CPL cache on a far jump, but since protected
mode transition will always jump to a segment with RPL=0, it will always
work.
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently the MMU's ->new_cr3() callback does nothing when guest paging
is disabled or when two-dimentional paging (e.g. EPT on Intel) is active.
This means that an emulated write to cr3 can be lost; kvm_set_cr3() will
write vcpu-arch.cr3, but the GUEST_CR3 field in the VMCS will retain its
old value and this is what the guest sees.
This bug did not have any effect until now because:
- with unrestricted guest, or with svm, we never emulate a mov cr3 instruction
- without unrestricted guest, and with paging enabled, we also never emulate a
mov cr3 instruction
- without unrestricted guest, but with paging disabled, the guest's cr3 is
ignored until the guest enables paging; at this point the value from arch.cr3
is loaded correctly my the mov cr0 instruction which turns on paging
However, the patchset that enables big real mode causes us to emulate mov cr3
instructions in protected mode sometimes (when guest state is not virtualizable
by vmx); this mov cr3 is effectively ignored and will crash the guest.
The fix is to make nonpaging_new_cr3() call mmu_free_roots() to force a cr3
reload. This is awkward because now all the new_cr3 callbacks to the same
thing, and because mmu_free_roots() is somewhat of an overkill; but fixing
that is more complicated and will be done after this minimal fix.
Observed in the Window XP 32-bit installer while bringing up secondary vcpus.
Signed-off-by: Avi Kivity <avi@redhat.com>
