Add triggers for DC6 as per details provided in skl_enable_dc6
and skl_disable_dc6 implementations.
Also Call POSTING_READ for every write to a register to ensure
it is written to immediately
v1: Remove POSTING_READ and intel_prepare_ddi calls as they've been added in previous patches.
v2:
1] Remove check for backlight disabled as it should be the case by that time.
2] Mark DC5 as disabled when enabling DC6.
3] Return from DC5-disabling function early if DC5 is already be disabled which can happen
due to DC6-enabling earlier.
3] Ensure CSR firmware is loaded after resume from DC6 as corresponding memory contents won't
be retained after runtime-suspend.
4] Ensure that CSR isn't identified as loaded before CSR-loading program is called during
runtime-resume.
v3: Rebase to latest
Modified as per review comments from Imre and after discussion with Art:
1] DC6 should be preferably enabled when PG2 is disabled by SW as the check for PG1 being
disabled is taken of by HW to enter DC6, and disabled when PG2 is enabled respectively.
This helps save more power, especially in the case when display is disabled but GT is
enabled. Accordingly, replacing DC5 trigger sequence with DC6 for SKL.
2] DC6 could be enabled from intel_runtime_suspend() function, if DC5 is already enabled.
3] Move CSR-load-status setting code from intel_runtime_suspend function to a new function.
v4:
1] Enable/disable DC6 only when toggling the power-well using a newly defined macro ENABLE_DC6.
v5:
1] Load CSR on system resume too as firmware may be lost on system suspend preventing
enabling DC5, DC6.
2] DDI buffers shouldn't be programmed during driver-load/resume as it's already done
during modeset initialization then and also that the encoder list is still uninitialized by
then. Therefore, call intel_prepare_ddi function right after disabling DC6 but outside
skl_disable_dc6 function and not during driver-load/resume.
v6:
1] Rebase to latest.
2] Move SKL_ENABLE_DC6 macro definition from intel_display.c to intel_runtime_pm.c.
v7:
1) Refactored the code for removing the warning got from checkpatch.
2) After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v8:
- Reverted the changes done in v7.
- Removed the condition check in skl_prepare_resune(). (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Warn if the conditions to enter or exit DC5 are not satisfied such
as support for runtime PM, state of power well, CSR loading etc.
v2: Removed camelcase in functions and variables.
v3: Do some minimal check to assert if CSR program is not loaded.
v4:
1] Used an appropriate function lookup_power_well() to identify power well,
instead of using a magic number which can change in future.
2] Split the conditions further in assert_can_enable_DC5() and added more checks.
3] Removed all WARNs from assert_can_disable_DC5 as they were unnecessary and added two
new ones.
4] Changed variable names as updated in earlier patches.
v5:
1] Change lookup_power_well function to take an int power well id.
2] Define a new intel_display_power_well_is_enabled helper function to check whether a
particular power well is enabled.
3] Use CSR-related mutex in assert_csr_loaded function.
v6: Remove use of dc5_enabled variable as it's no longer needed.
v7:
1] Rebase to latest.
2] Move all DC5-related functions from intel_display.c to intel_runtime_pm.c.
v8: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v9: Modified below changes based on review comments from Imre.
- Moved intel_display_power_well_is_enabled() to intel_runtime_pm.c.
- Removed mutex lock from assert_csr_loaded(). (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch just implements the basic enable and disable
functions of DC5 state which is needed for both SKL and BXT.
Its important to load respective CSR program before calling
enable, which anyways will happen as CSR program is executed
during boot.
DC5 is a power saving state where hardware dynamically disables
power well 1 and the CDCLK PLL and saves the associated registers.
DC5 can be entered when software allows it, power well 2 is
disabled, and hardware detects that all pipes are disabled
or pipe A is enabled with PSR active.
Its better to configure display engine to have power well 2 disabled before
getting into DC5 enable function. Hence rpm framework will have to
ensure to check status of power well 2 before calling gen9_enable_dc5.
Rather dc5 entry criteria should be decided based on power well 2 status.
If disabled, then call gen9_enable_dc5.
v2: Replace HAS_ with IS_ check as per Daniel's review comments
v3: Cleared the bits dc5/dc6 enable of DC_STATE_EN register
before setting them as per Satheesh's review comments.
v4: call POSTING_READ for every write to a register to ensure that
its written immediately.
v5: Modified as per review comments from Imre.
- Squashed register definitions into this patch.
- Finetuned comments and functions.
v6:
Avoid redundant writes in gen9_set_dc_state_debugmask_memory_up function.
v7:
- Rebase to latest.
- Move all runtime PM functions defined in intel_display.c to
intel_runtime_pm.c.
v8: Rebased to drm-intel-nightly. (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add triggers as per expectations mentioned in gen9_enable_dc5
and gen9_disable_dc5 patch.
Also call POSTING_READ for every write to a register to ensure that
its written immediately.
v1: Remove POSTING_READ calls as they've already been added in previous patches.
v2: Rebase to move all runtime pm specific changes to intel_runtime_pm.c file.
Modified as per review comments from Imre:
1] Change variable name 'dc5_allowed' to 'dc5_enabled' to correspond to relevant
functions.
2] Move the check dc5_enabled in skl_set_power_well() to disable DC5 into
gen9_disable_DC5 which is a more appropriate place.
3] Convert checks for 'pm.dc5_enabled' and 'pm.suspended' in skl_set_power_well()
to warnings. However, removing them for now as they'll be included in a future patch
asserting DC-state entry/exit criteria.
4] Enable DC5, only when CSR firmware is verified to be loaded. Create new structure
to track 'enabled' and 'deferred' status of DC5.
5] Ensure runtime PM reference is obtained, if CSR is not loaded, to avoid entering
runtime-suspend and release it when it's loaded.
6] Protect necessary CSR-related code with locks.
7] Move CSR-loading call to runtime PM initialization, as power domains needed to be
accessed during deferred DC5-enabling, are not initialized earlier.
v3: Rebase to latest.
Modified as per review comments from Imre:
1] Use blocking wait for CSR-loading to finish to enable DC5 for simplicity, instead of
deferring enabling DC5 until CSR is loaded.
2] Obtain runtime PM reference during CSR-loading initialization itself as deferred DC5-
enabling is removed and release it at the end of CSR-loading functionality.
3] Revert calling CSR-loading functionality to the beginning of i915 driver-load
functionality to avoid any delay in loading.
4] Define another variable to track whether CSR-loading failed and use it to avoid enabling
DC5 if it's true.
5] Define CSR-load-status accessor functions for use later.
v4:
1] Disable DC5 before enabling PG2 instead of after it.
2] DC5 was being mistaken enabled even when CSR-loading timed-out. Fix that.
3] Enable DC5-related functionality using a macro.
4] Remove dc5_enabled tracking variable and its use as it's not needed now.
v5:
1] Mark CSR failed to load where necessary in finish_csr_load function.
2] Use mutex-protected accessor function to check if CSR loaded instead of directly
accessing the variable.
3] Prefix csr_load_status_get/set function names with intel_.
v6: rebase to latest.
v7: Rebase on top of nightly (Damien)
v8: Squashed the patch from Imre - added csr helper pointers to simplify the code. (Imre)
v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v10: Added a enum for different csr states, suggested by Imre. (Animesh)
v11: Based on review comments from Imre, Damien and Daniel following changes done
- enum name chnaged to csr_state (singular form).
- FW_UNINITIALIZED used as zeroth element in enum csr_state.
- Prototype changed for helper function(set/get csr status), using enum csr_state instead of bool.
v12: Based on review comment from Imre, introduced bool fw_loaded local to finish_csr_load() which helps
calling once to set the csr status. The same flag used to fail RPM if find any issue during
firmware loading.
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display Context Save and Restore support is needed for
various SKL Display C states like DC5, DC6.
This implementation is added based on first version of DMC CSR program
that we received from h/w team.
Here we are using request_firmware based design.
Finally this firmware should end up in linux-firmware tree.
For SKL platform its mandatory to ensure that we load this
csr program before enabling DC states like DC5/DC6.
As CSR program gets reset on various conditions, we should ensure
to load it during boot and in future change to be added to load
this system resume sequence too.
v1: Initial relese as RFC patch
v2: Design change as per Daniel, Damien and Shobit's review comments
request firmware method followed.
v3: Some optimization and functional changes.
Pulled register defines into drivers/gpu/drm/i915/i915_reg.h
Used kmemdup to allocate and duplicate firmware content.
Ensured to free allocated buffer.
v4: Modified as per review comments from Satheesh and Daniel
Removed temporary buffer.
Optimized number of writes by replacing I915_WRITE with I915_WRITE64.
v5:
Modified as per review comemnts from Damien.
- Changed name for functions and firmware.
- Introduced HAS_CSR.
- Reverted back previous change and used csr_buf with u8 size.
- Using cpu_to_be64 for endianness change.
Modified as per review comments from Imre.
- Modified registers and macro names to be a bit closer to bspec terminology
and the existing register naming in the driver.
- Early return for non SKL platforms in intel_load_csr_program function.
- Added locking around CSR program load function as it may be called
concurrently during system/runtime resume.
- Releasing the fw before loading the program for consistency
- Handled error path during f/w load.
v6: Modified as per review comments from Imre.
- Corrected out_freecsr sequence.
v7: Modified as per review comments from Imre.
Fail loading fw if fw->size%8!=0.
v8: Rebase to latest.
v9: Rebase on top of -nightly (Damien)
v10: Enabled support for dmc firmware ver 1.0.
According to ver 1.0 in a single binary package all the firmware's that are
required for different stepping's of the product will be stored. The package
contains the css header, followed by the package header and the actual dmc
firmwares. Package header contains the firmware/stepping mapping table and
the corresponding firmware offsets to the individual binaries, within the
package. Each individual program binary contains the header and the payload
sections whose size is specified in the header section. This changes are done
to extract the specific firmaware from the package. (Animesh)
v11: Modified as per review comemnts from Imre.
- Added code comment from bpec for header structure elements.
- Added __packed to avoid structure padding.
- Added helper functions for stepping and substepping info.
- Added code comment for CSR_MAX_FW_SIZE.
- Disabled BXT firmware loading, will be enabled with dmc 1.0 support.
- Changed skl_stepping_info based on bspec, earlier used from config DB.
- Removed duplicate call of cpu_to_be* from intel_csr_load_program function.
- Used cpu_to_be32 instead of cpu_to_be64 as firmware binary in dword aligned.
- Added sanity check for header length.
- Added sanity check for mmio address got from firmware binary.
- kmalloc done separately for dmc header and dmc firmware. (Animesh)
v12: Modified as per review comemnts from Imre.
- Corrected the typo error in skl stepping info structure.
- Added out-of-bound access for skl_stepping_info.
- Sanity check for mmio address modified.
- Sanity check added for stepping and substeppig.
- Modified the intel_dmc_info structure, cache only the required header info. (Animesh)
v13: clarify firmware load error message.
The reason for a firmware loading failure can be obscure if the driver
is built-in. Provide an explanation to the user about the likely reason for
the failure and how to resolve it. (Imre)
v14: Suggested by Jani.
- fix s/I915/CONFIG_DRM_I915/ typo
- add fw_path to the firmware object instead of using a static ptr (Jani)
v15:
1) Changed the firmware name as dmc_gen9.bin, everytime for a new firmware version a symbolic link
with same name will help not to build kernel again.
2) Changes done as per review comments from Imre.
- Error check removed for intel_csr_ucode_init.
- Moved csr-specific data structure to intel_csr.h and optimization done on structure definition.
- fw->data used directly for parsing the header info & memory allocation
only done separately for payload. (Animesh)
v16:
- No need for out_regs label in i915_driver_load(), so removed it.
- Changed the firmware name as skl_dmc_ver1.bin, followed naming convention <platform>_dmc_<api-version>.bin (Animesh)
Issue: VIZ-2569
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_needs_cmd_parser already checks that for us.
Suggested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables skylake sprite plane display scaling using shared
scalers atomic desgin.
v2:
-use single copy of scaler limits (Matt)
v3:
-detaching scalers moved to crtc commit path (Matt)
v4:
-changes to align with updated scaler structures (Matt, me)
-keep sprite src rect in 16.16 format (Matt, Daniel)
v5:
-rebased on top of 90/270 rotation changes (me)
-Refactored skl_update_plane to reduce its size (Daniel)
It is a step towards having a single function covering all planes.
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Testcase: igt/kms_plane_scaling
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables skylake primary plane scaling using shared
scalers atomic desgin.
v2:
-use single copy of scaler limits (Matt)
v3:
-move detach_scalers to crtc commit path (Matt)
-use values in plane_state->src as regular integers (me)
v4:
-changes to align with updated scaler structures (Matt, me)
-keep plane src rect in 16.16 format (Matt, Daniel)
v5:
-Rebased on top of 90/270 rotation changes (me)
-Fixed an issue introduced by 90/270 changes where plane programming
is using drm_plane->state rect instead of intel_plane->state rect.
This change also required for scaling to work properly. (me)
-With 90/270, updated limits to cover both portrait and landscape usages (me)
-Refactored skylake_update_primary_plane to reduce its size (Daniel)
Added helper functions for refactoring are comprehended enough to be
used for skylake_update_plane (for sprite) too. One stop towards
having single function for all planes.
v6:
-Added fixme note when checking plane_state->src width in update_plane (Daniel)
-Release lock when failing to colorkey request with active scaler (Daniel)
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Reviewed-by: matthew.d.roper@intel.com
Reviewed-by: sonika.jindal@intel.com (v5)
Testcase: igt/kms_plane_scaling
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since:
b53b5eda81 ("x86/cpu: Increase max CPU count to 8192")
... the maximum supported NR_CPUS for CPUMASK_OFFSTACK case
is 8192. Let's adjust the description to reflect the change.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1431080726-2490-1-git-send-email-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Default NR_CPUS==8 is not enough to cover high-end desktop
configuration: Haswell-E has upto 16 threads.
Let's increase default NR_CPUS to 64 on 64-bit configuration.
With this value CPU bitmask will still fit into one unsigned long.
Default for 32-bit configuration is still 8: it's unlikely
anybody will run 32-bit kernels on modern hardware.
As an alternative we could bump NR_CPUS to 128 to cover all
dual-processor servers with some margin.
For reference: Debian and Suse build their kernels with
NR_CPUS==512, Fedora -- 1024.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1431080745-19792-1-git-send-email-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tegra would not only need a hardware vblank counter that
increments at leading edge of vblank, but also support
for instantaneous high precision vblank timestamp queries, ie.
a proper implementation of dev->driver->get_vblank_timestamp().
Without these, there can be off-by-one errors during vblank
disable/enable if the scanout is inside vblank at en/disable
time, and additionally clients will never see any useable
vblank timestamps when querying via drmWaitVblank ioctl. This
would negatively affect swap scheduling under X11 and Wayland.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With both gcc 4.7.2 and 4.9.2, sometimes gcc mysteriously
doesn't inline very small functions we expect to be inlined:
$ nm --size-sort vmlinux | grep -iF ' t ' | uniq -c | grep -v '^
*1 ' | sort -rn 473 000000000000000b t spin_unlock_irqrestore
449 000000000000005f t rcu_read_unlock
355 0000000000000009 t atomic_inc <== THIS
353 000000000000006e t rcu_read_lock
350 0000000000000075 t rcu_read_lock_sched_held
291 000000000000000b t spin_unlock
266 0000000000000019 t arch_local_irq_restore
215 000000000000000b t spin_lock
180 0000000000000011 t kzalloc
165 0000000000000012 t list_add_tail
161 0000000000000019 t arch_local_save_flags
153 0000000000000016 t test_and_set_bit
134 000000000000000b t spin_unlock_irq
134 0000000000000009 t atomic_dec <== THIS
130 000000000000000b t spin_unlock_bh
122 0000000000000010 t brelse
120 0000000000000016 t test_and_clear_bit
120 000000000000000b t spin_lock_irq
119 000000000000001e t get_dma_ops
117 0000000000000053 t cpumask_next
116 0000000000000036 t kref_get
114 000000000000001a t schedule_work
106 000000000000000b t spin_lock_bh
103 0000000000000019 t arch_local_irq_disable
...
Note sizes of marked functions. They are merely 9 bytes long!
Selecting function with 'atomic' in their names:
355 0000000000000009 t atomic_inc
134 0000000000000009 t atomic_dec
98 0000000000000014 t atomic_dec_and_test
31 000000000000000e t atomic_add_return
27 000000000000000a t atomic64_inc
26 000000000000002f t kmap_atomic
24 0000000000000009 t atomic_add
12 0000000000000009 t atomic_sub
10 0000000000000021 t __atomic_add_unless
10 000000000000000a t atomic64_add
5 000000000000001f t __atomic_add_unless.constprop.7
5 000000000000000a t atomic64_dec
4 000000000000001f t __atomic_add_unless.constprop.18
4 000000000000001f t __atomic_add_unless.constprop.12
4 000000000000001f t __atomic_add_unless.constprop.10
3 000000000000001f t __atomic_add_unless.constprop.13
3 0000000000000011 t atomic64_add_return
2 000000000000001f t __atomic_add_unless.constprop.9
2 000000000000001f t __atomic_add_unless.constprop.8
2 000000000000001f t __atomic_add_unless.constprop.6
2 000000000000001f t __atomic_add_unless.constprop.5
2 000000000000001f t __atomic_add_unless.constprop.3
2 000000000000001f t __atomic_add_unless.constprop.22
2 000000000000001f t __atomic_add_unless.constprop.14
2 000000000000001f t __atomic_add_unless.constprop.11
2 000000000000001e t atomic_dec_if_positive
2 0000000000000014 t atomic_inc_and_test
2 0000000000000011 t atomic_add_return.constprop.4
2 0000000000000011 t atomic_add_return.constprop.17
2 0000000000000011 t atomic_add_return.constprop.16
2 000000000000000d t atomic_inc.constprop.4
2 000000000000000c t atomic_cmpxchg
This patch fixes this for x86 atomic ops via
s/inline/__always_inline/. This decreases allyesconfig kernel by
about 25k:
text data bss dec hex filename
82399481 22255416 20627456 125282353 777a831 vmlinux.before
82375570 22255544 20627456 125258570 7774b4a vmlinux
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1431080762-17797-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Add missing initialization of SDMA vm register when creating an SDMA queue
- Don't report local memory size, as we don't support local memory allocation
yet.
- Allow to unregister process with exisiting queues. Until now we blocked
it with BUG_ON, which was also an error by itself.
* tag 'drm-amdkfd-fixes-2015-05-07' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Initialize sdma vm when creating sdma queue
drm/amdkfd: Don't report local memory size
drm/amdkfd: allow unregister process with queues
Mostly stability fixes for UVD and VCE, plus a few other bug and regression
fixes.
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
drm/radeon: make UVD handle checking more strict
drm/radeon: make VCE handle check more strict
drm/radeon: fix userptr lockup
drm/radeon: fix userptr BO unpin bug v3
drm/radeon: don't setup audio on asics that don't support it
drm/radeon: disable semaphores for UVD V1 (v2)
drm-intel-next-2015-04-23:
- dither support for ns2501 dvo (Thomas Richter)
- some polish for the gtt code and fixes to finally enable the cmd parser on hsw
- first pile of bxt stage 1 enabling (too many different people to list ...)
- more psr fixes from Rodrigo
- skl rotation support from Chandra
- more atomic work from Ander and Matt
- pile of cleanups and micro-ops for execlist from Chris
drm-intel-next-2015-04-10:
- cdclk handling cleanup and fixes from Ville
- more prep patches for olr removal from John Harrison
- gmbus pin naming rework from Jani (prep for bxt)
- remove ->new_config from Ander (more atomic conversion work)
- rps (boost) tuning and unification with byt/bsw from Chris
- cmd parser batch bool tuning from Chris
- gen8 dynamic pte allocation (Michel Thierry, based on work from Ben Widawsky)
- execlist tuning (not yet all of it) from Chris
- add drm_plane_from_index (Chandra)
- various small things all over
* tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel: (204 commits)
drm/i915/gtt: Allocate va range only if vma is not bound
drm/i915: Enable cmd parser to do secure batch promotion for aliasing ppgtt
drm/i915: fix intel_prepare_ddi
drm/i915: factor out ddi_get_encoder_port
drm/i915/hdmi: check port in ibx_infoframe_enabled
drm/i915/hdmi: fix vlv infoframe port check
drm/i915: Silence compiler warning in dvo
drm/i915: Update DRIVER_DATE to 20150423
drm/i915: Enable dithering on NatSemi DVO2501 for Fujitsu S6010
rm/i915: Move i915_get_ggtt_vma_pages into ggtt_bind_vma
drm/i915: Don't try to outsmart gcc in i915_gem_gtt.c
drm/i915: Unduplicate i915_ggtt_unbind/bind_vma
drm/i915: Move ppgtt_bind/unbind around
drm/i915: move i915_gem_restore_gtt_mappings around
drm/i915: Fix up the vma aliasing ppgtt binding
drm/i915: Remove misleading comment around bind_to_vm
drm/i915: Don't use atomics for pg_dirty_rings
drm/i915: Don't look at pg_dirty_rings for aliasing ppgtt
drm/i915/skl: Support Y tiling in MMIO flips
drm/i915: Fixup kerneldoc for struct intel_context
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
So Linus noticed that in:
94d4b4765b ("x86/mm: Clean up types in xlate_dev_mem_ptr()")
... I added two nonsensical casts, due to the poor type choice
for 'vaddr'.
Change it to 'void *' and take advantage of void * arithmetics.
This removes the casts.
( Also remove a nonsensical return line from unxlate_dev_mem_ptr()
while at it. )
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds the necessary Xen specific code to allow Xen to
support the CPU halting and kicking operations needed by the queue
spinlock PV code.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-12-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds the necessary KVM specific code to allow KVM to
support the CPU halting and kicking operations needed by the queue
spinlock PV code.
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-11-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We use the regular paravirt call patching to switch between:
native_queued_spin_lock_slowpath() __pv_queued_spin_lock_slowpath()
native_queued_spin_unlock() __pv_queued_spin_unlock()
We use a callee saved call for the unlock function which reduces the
i-cache footprint and allows 'inlining' of SPIN_UNLOCK functions
again.
We further optimize the unlock path by patching the direct call with a
"movb $0,%arg1" if we are indeed using the native unlock code. This
makes the unlock code almost as fast as the !PARAVIRT case.
This significantly lowers the overhead of having
CONFIG_PARAVIRT_SPINLOCKS enabled, even for native code.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-10-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Provide a separate (second) version of the spin_lock_slowpath for
paravirt along with a special unlock path.
The second slowpath is generated by adding a few pv hooks to the
normal slowpath, but where those will compile away for the native
case, they expand into special wait/wake code for the pv version.
The actual MCS queue can use extra storage in the mcs_nodes[] array to
keep track of state and therefore uses directed wakeups.
The head contender has no such storage directly visible to the
unlocker. So the unlocker searches a hash table with open addressing
using a simple binary Galois linear feedback shift register.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1429901803-29771-9-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When we detect a hypervisor (!paravirt, see qspinlock paravirt support
patches), revert to a simple test-and-set lock to avoid the horrors
of queue preemption.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-8-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, atomic_cmpxchg() is used to get the lock. However, this
is not really necessary if there is more than one task in the queue
and the queue head don't need to reset the tail code. For that case,
a simple write to set the lock bit is enough as the queue head will
be the only one eligible to get the lock as long as it checks that
both the lock and pending bits are not set. The current pending bit
waiting code will ensure that the bit will not be set as soon as the
tail code in the lock is set.
With that change, the are some slight improvement in the performance
of the queued spinlock in the 5M loop micro-benchmark run on a 4-socket
Westere-EX machine as shown in the tables below.
[Standalone/Embedded - same node]
# of tasks Before patch After patch %Change
---------- ----------- ---------- -------
3 2324/2321 2248/2265 -3%/-2%
4 2890/2896 2819/2831 -2%/-2%
5 3611/3595 3522/3512 -2%/-2%
6 4281/4276 4173/4160 -3%/-3%
7 5018/5001 4875/4861 -3%/-3%
8 5759/5750 5563/5568 -3%/-3%
[Standalone/Embedded - different nodes]
# of tasks Before patch After patch %Change
---------- ----------- ---------- -------
3 12242/12237 12087/12093 -1%/-1%
4 10688/10696 10507/10521 -2%/-2%
It was also found that this change produced a much bigger performance
improvement in the newer IvyBridge-EX chip and was essentially to close
the performance gap between the ticket spinlock and queued spinlock.
The disk workload of the AIM7 benchmark was run on a 4-socket
Westmere-EX machine with both ext4 and xfs RAM disks at 3000 users
on a 3.14 based kernel. The results of the test runs were:
AIM7 XFS Disk Test
kernel JPM Real Time Sys Time Usr Time
----- --- --------- -------- --------
ticketlock 5678233 3.17 96.61 5.81
qspinlock 5750799 3.13 94.83 5.97
AIM7 EXT4 Disk Test
kernel JPM Real Time Sys Time Usr Time
----- --- --------- -------- --------
ticketlock 1114551 16.15 509.72 7.11
qspinlock 2184466 8.24 232.99 6.01
The ext4 filesystem run had a much higher spinlock contention than
the xfs filesystem run.
The "ebizzy -m" test was also run with the following results:
kernel records/s Real Time Sys Time Usr Time
----- --------- --------- -------- --------
ticketlock 2075 10.00 216.35 3.49
qspinlock 3023 10.00 198.20 4.80
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-7-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When we allow for a max NR_CPUS < 2^14 we can optimize the pending
wait-acquire and the xchg_tail() operations.
By growing the pending bit to a byte, we reduce the tail to 16bit.
This means we can use xchg16 for the tail part and do away with all
the repeated compxchg() operations.
This in turn allows us to unconditionally acquire; the locked state
as observed by the wait loops cannot change. And because both locked
and pending are now a full byte we can use simple stores for the
state transition, obviating one atomic operation entirely.
This optimization is needed to make the qspinlock achieve performance
parity with ticket spinlock at light load.
All this is horribly broken on Alpha pre EV56 (and any other arch that
cannot do single-copy atomic byte stores).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-6-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is a preparatory patch that extracts out the following 2 code
snippets to prepare for the next performance optimization patch.
1) the logic for the exchange of new and previous tail code words
into a new xchg_tail() function.
2) the logic for clearing the pending bit and setting the locked bit
into a new clear_pending_set_locked() function.
This patch also simplifies the trylock operation before queuing by
calling queued_spin_trylock() directly.
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-5-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Because the qspinlock needs to touch a second cacheline (the per-cpu
mcs_nodes[]); add a pending bit and allow a single in-word spinner
before we punt to the second cacheline.
It is possible so observe the pending bit without the locked bit when
the last owner has just released but the pending owner has not yet
taken ownership.
In this case we would normally queue -- because the pending bit is
already taken. However, in this case the pending bit is guaranteed
to be released 'soon', therefore wait for it and avoid queueing.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-4-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch makes the necessary changes at the x86 architecture
specific layer to enable the use of queued spinlocks for x86-64. As
x86-32 machines are typically not multi-socket. The benefit of queue
spinlock may not be apparent. So queued spinlocks are not enabled.
Currently, there is some incompatibilities between the para-virtualized
spinlock code (which hard-codes the use of ticket spinlock) and the
queued spinlocks. Therefore, the use of queued spinlocks is disabled
when the para-virtualized spinlock is enabled.
The arch/x86/include/asm/qspinlock.h header file includes some x86
specific optimization which will make the queueds spinlock code
perform better than the generic implementation.
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-3-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch introduces a new generic queued spinlock implementation that
can serve as an alternative to the default ticket spinlock. Compared
with the ticket spinlock, this queued spinlock should be almost as fair
as the ticket spinlock. It has about the same speed in single-thread
and it can be much faster in high contention situations especially when
the spinlock is embedded within the data structure to be protected.
Only in light to moderate contention where the average queue depth
is around 1-3 will this queued spinlock be potentially a bit slower
due to the higher slowpath overhead.
This queued spinlock is especially suit to NUMA machines with a large
number of cores as the chance of spinlock contention is much higher
in those machines. The cost of contention is also higher because of
slower inter-node memory traffic.
Due to the fact that spinlocks are acquired with preemption disabled,
the process will not be migrated to another CPU while it is trying
to get a spinlock. Ignoring interrupt handling, a CPU can only be
contending in one spinlock at any one time. Counting soft IRQ, hard
IRQ and NMI, a CPU can only have a maximum of 4 concurrent lock waiting
activities. By allocating a set of per-cpu queue nodes and used them
to form a waiting queue, we can encode the queue node address into a
much smaller 24-bit size (including CPU number and queue node index)
leaving one byte for the lock.
Please note that the queue node is only needed when waiting for the
lock. Once the lock is acquired, the queue node can be released to
be used later.
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel J Blueman <daniel@numascale.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <paolo.bonzini@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1429901803-29771-2-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Looks like commit :
43239cbe79 ("kernel: Change ASSIGN_ONCE(val, x) to WRITE_ONCE(x, val)")
left behind a reference to ASSIGN_ONCE(). Update this to WRITE_ONCE().
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: borntraeger@de.ibm.com
Cc: dave@stgolabs.net
Cc: paulmck@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/20150430115721.22278.94082.stgit@preeti.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In up_write()/up_read(), rwsem_wake() will be called whenever it
detects that some writers/readers are waiting. The rwsem_wake()
function will take the wait_lock and call __rwsem_do_wake() to do the
real wakeup. For a heavily contended rwsem, doing a spin_lock() on
wait_lock will cause further contention on the heavily contended rwsem
cacheline resulting in delay in the completion of the up_read/up_write
operations.
This patch makes the wait_lock taking and the call to __rwsem_do_wake()
optional if at least one spinning writer is present. The spinning
writer will be able to take the rwsem and call rwsem_wake() later
when it calls up_write(). With the presence of a spinning writer,
rwsem_wake() will now try to acquire the lock using trylock. If that
fails, it will just quit.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Jason Low <jason.low2@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Douglas Hatch <doug.hatch@hp.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1430428337-16802-2-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On powerpc the perf event interrupt is not masked when interrupts are
disabled, allowing it to function as an NMI.
This causes problems if perf is using vmalloc. If we take a page fault
on the vmalloc region the fault handler will fail the page fault because
it detects we are coming in from an NMI (see do_hash_page()).
We don't actually need or want vmalloc backed perf so just disable it on
powerpc.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <linuxppc-dev@ozlabs.org>
Cc: Andrew Morton <akpm@osdl.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@ghostprotocols.net
Cc: sukadev@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1430720799-18426-1-git-send-email-mpe@ellerman.id.au
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Stephane asked about PERF_COUNT_SW_CPU_MIGRATIONS and I realized it
was borken:
> The problem is that the task isn't actually scheduled while its being
> migrated (obviously), and if its not scheduled, the counters aren't
> scheduled either, so there's no observing of the fact.
>
> A further problem with migrations is that many migrations happen from
> softirq context, which is nested inside the 'random' task context of
> whoemever happens to run at that time, similarly for the wakeup
> migrations triggered from (soft)irq context. All those end up being
> accounted in the task that's currently running, eg. your 'ls'.
The below cures this by marking a task as migrated and accounting it
on the subsequent sched_in().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The is a missing mutex unlock on the error path in
snd_soc_dapm_get_enum_double. This was introduced in commit
561ed680b7 ("ASoC: dapm: Add support for autodisable mux controls").
This patch adds the missing unlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the wakeup_process() invocation so it is not done under
the info->lock by making use of a lockless wake_q. With this change, the
waiter is woken up once it is STATE_READY and it does not need to loop
on SMP if it is still in STATE_PENDING. In the timeout case we still need
to grab the info->lock to verify the state.
This change should also avoid the introduction of preempt_disable() in -rt
which avoids a busy-loop which pools for the STATE_PENDING -> STATE_READY
change if the waiter has a higher priority compared to the waker.
Additionally, this patch micro-optimizes wq_sleep by using the cheaper
cousin of set_current_state(TASK_INTERRUPTABLE) as we will block no
matter what, thus get rid of the implied barrier.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: George Spelvin <linux@horizon.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Mason <clm@fb.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: dave@stgolabs.net
Link: http://lkml.kernel.org/r/1430748166.1940.17.camel@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Given the overall futex architecture, any chance of reducing
hb->lock contention is welcome. In this particular case, using
wake-queues to enable lockless wakeups addresses very much real
world performance concerns, even cases of soft-lockups in cases
of large amounts of blocked tasks (which is not hard to find in
large boxes, using but just a handful of futex).
At the lowest level, this patch can reduce latency of a single thread
attempting to acquire hb->lock in highly contended scenarios by a
up to 2x. At lower counts of nr_wake there are no regressions,
confirming, of course, that the wake_q handling overhead is practically
non existent. For instance, while a fair amount of variation,
the extended pef-bench wakeup benchmark shows for a 20 core machine
the following avg per-thread time to wakeup its share of tasks:
nr_thr ms-before ms-after
16 0.0590 0.0215
32 0.0396 0.0220
48 0.0417 0.0182
64 0.0536 0.0236
80 0.0414 0.0097
96 0.0672 0.0152
Naturally, this can cause spurious wakeups. However there is no core code
that cannot handle them afaict, and furthermore tglx does have the point
that other events can already trigger them anyway.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Mason <clm@fb.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: George Spelvin <linux@horizon.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1430494072-30283-3-git-send-email-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is useful for locking primitives that can effect multiple
wakeups per operation and want to avoid lock internal lock contention
by delaying the wakeups until we've released the lock internal locks.
Alternatively it can be used to avoid issuing multiple wakeups, and
thus save a few cycles, in packet processing. Queue all target tasks
and wakeup once you've processed all packets. That way you avoid
waking the target task multiple times if there were multiple packets
for the same task.
Properties of a wake_q are:
- Lockless, as queue head must reside on the stack.
- Being a queue, maintains wakeup order passed by the callers. This can
be important for otherwise, in scenarios where highly contended locks
could affect any reliance on lock fairness.
- A queued task cannot be added again until it is woken up.
This patch adds the needed infrastructure into the scheduler code
and uses the new wake_list to delay the futex wakeups until
after we've released the hash bucket locks.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
[tweaks, adjustments, comments, etc.]
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Mason <clm@fb.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: George Spelvin <linux@horizon.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1430494072-30283-2-git-send-email-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Recent optimizations were made to thread_group_cputimer to improve its
scalability by keeping track of cputime stats without a lock. However,
the values were open coded to the structure, causing them to be at
a different abstraction level from the regular task_cputime structure.
Furthermore, any subsequent similar optimizations would not be able to
share the new code, since they are specific to thread_group_cputimer.
This patch adds the new task_cputime_atomic data structure (introduced in
the previous patch in the series) to thread_group_cputimer for keeping
track of the cputime atomically, which also helps generalize the code.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Waiman Long <Waiman.Long@hp.com>
Link: http://lkml.kernel.org/r/1430251224-5764-6-git-send-email-jason.low2@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds an atomic variant of the 'struct task_cputime' data structure,
which can be used to store and update task_cputime statistics without
needing to do locking.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Waiman Long <Waiman.Long@hp.com>
Link: http://lkml.kernel.org/r/1430251224-5764-5-git-send-email-jason.low2@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While running a database workload, we found a scalability issue with itimers.
Much of the problem was caused by the thread_group_cputimer spinlock.
Each time we account for group system/user time, we need to obtain a
thread_group_cputimer's spinlock to update the timers. On larger systems
(such as a 16 socket machine), this caused more than 30% of total time
spent trying to obtain this kernel lock to update these group timer stats.
This patch converts the timers to 64-bit atomic variables and use
atomic add to update them without a lock. With this patch, the percent
of total time spent updating thread group cputimer timers was reduced
from 30% down to less than 1%.
Note: On 32-bit systems using the generic 64-bit atomics, this causes
sample_group_cputimer() to take locks 3 times instead of just 1 time.
However, we tested this patch on a 32-bit system ARM system using the
generic atomics and did not find the overhead to be much of an issue.
An explanation for why this isn't an issue is that 32-bit systems usually
have small numbers of CPUs, and cacheline contention from extra spinlocks
called periodically is not really apparent on smaller systems.
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Waiman Long <Waiman.Long@hp.com>
Link: http://lkml.kernel.org/r/1430251224-5764-4-git-send-email-jason.low2@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The p->mm->numa_scan_seq is accessed using READ_ONCE/WRITE_ONCE
and modified without exclusive access. It is not clear why it is
accessed this way. This patch provides some documentation on that.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Waiman Long <waiman.long@hp.com>
Link: http://lkml.kernel.org/r/1430440094.2475.61.camel@j-VirtualBox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ACCESS_ONCE doesn't work reliably on non-scalar types. This patch removes
the rest of the existing usages of ACCESS_ONCE() in the scheduler, and use
the new READ_ONCE() and WRITE_ONCE() APIs as appropriate.
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Waiman Long <Waiman.Long@hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Scott J Norton <scott.norton@hp.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1430251224-5764-2-git-send-email-jason.low2@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
'rt_period_us' is automatically type converted from u64 to long and then cast
back to u64 - this down/up conversion is unnecessary and can be removed to
improve readability.
This will also help us not truncate 'rt_period_us' to 32 bits on 32-bit kernels,
should we ever have so large values. (unlikely, not the least due to procfs.)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1430643116-24049-1-git-send-email-hofrat@osadl.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The misaligned load exception arises when running ptrace_attach() on
the RISC-V (which hasn't been upstreamed yet). The problem is that
wait_on_bit() takes a void* but then proceeds to call test_bit(),
which takes a long*. This allows an int-aligned pointer to be passed
to test_bit(), which promptly fails. This will manifest on any other
asm-generic port where unaligned loads trap, where sizeof(long) >
sizeof(int), and where task_struct.jobctl ends up not being
long-aligned.
This patch changes task_struct.jobctl to be a long, which ensures it
has the correct alignment.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bobby.prani@gmail.com
Cc: oleg@redhat.com
Cc: paulmck@linux.vnet.ibm.com
Cc: richard@nod.at
Cc: vdavydov@parallels.com
Link: http://lkml.kernel.org/r/1430453997-32459-2-git-send-email-palmer@dabbelt.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The implementations of wait_on_bit*() will only work with long-aligned
memory on systems that don't support misaligned loads and stores.
This patch changes the function prototypes to ensure that the compiler
will enforce alignment.
Running
make defconfig
make KFLAGS="-Werror"
seems to indicate that, as of c56fb6564dcd ("Fix a misaligned load
inside ptrace_attach()"), there are now no users of non-long-aligned
calls to wait_on_bit*(). I additionally tried a few "make randconfig"
attempts, none of which failed to compile for this reason.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bobby.prani@gmail.com
Cc: oleg@redhat.com
Cc: paulmck@linux.vnet.ibm.com
Cc: richard@nod.at
Cc: vdavydov@parallels.com
Link: http://lkml.kernel.org/r/1430453997-32459-3-git-send-email-palmer@dabbelt.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
c56fb6564dcd ("Fix a misaligned load inside ptrace_attach()") makes
jobctl an "unsigned long". It makes sense to have the masks applied
to it match that type. This is currently just a cosmetic change, but
it will prevent the mask from being unexpectedly truncated if we ever
end up with masks with more bits.
One instance of "signr" is an int, but I left this alone because the
mask ensures that it will never overflow.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bobby.prani@gmail.com
Cc: oleg@redhat.com
Cc: paulmck@linux.vnet.ibm.com
Cc: richard@nod.at
Cc: vdavydov@parallels.com
Link: http://lkml.kernel.org/r/1430453997-32459-4-git-send-email-palmer@dabbelt.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I could not find the loadavg code.. turns out it was hidden in a file
called proc.c. It further got mingled up with the cruft per rq load
indexes (which we really want to get rid of).
Move the per rq load indexes into the fair.c load-balance code (that's
the only thing that uses them) and rename proc.c to loadavg.c so we
can find it again.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
[ Did minor cleanups to the code. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
iTLB-load-misses and LLC-load-misses count incorrectly on SLM.
There is no ITLB.MISSES support on SLM. Event PAGE_WALKS.I_SIDE_WALK
should be used to count iTLB-load-misses. This event counts when an
instruction (I) page walk is completed or started. Since a page walk
implies a TLB miss, the number of TLB misses can be counted by counting
the number of pagewalks.
DMND_DATA_RD counts both demand and DCU prefetch data reads. However,
LLC-load-misses should only count demand reads. There is no way to not
include prefetches with a single counter on SLM. So the LLC-load-misses
support should be removed on SLM.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1429608881-5055-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
