Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).
Fixes: cca8b13375 ("net: dsa: Use mnemonics rather than register numbers")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
net: Fix "hw csum failure" message flood for ppp tunnel
This patch set addresses bug "Bug 95171 - "hw csum failure" message
flood for ppp tunnel since upgrade to 3.16". The problem is that pppoe
is being used over UDP with UDP checksusm enabled. On receive
checksum conversion turns checksum-unnecessary in checksum-
complete. The PPP receive functions do not properly pull
the checksum over its headers, so that when an encapsulated
checksums is considered the checksum-complete value is incorrect.
This patch adds skb_checksum_complete_unset which can be called
in the receive path in lieu of pulling checksum complete in
layer. This is useful when the packet is being modified (e.g.
decompressed) and the checksum-complete value is no longer
relevant.
In the ppp_receive_frame we call skb_checksum_complete_unset to toss
out checksum-complete. This should eliminate the reported messages.
Alternatively, we could add skb_postpull_rcsum and probably
special case handling for VJ compression if maintaining the
checksum-complete is needed (not clear to me this is worth the
effort).
I haven't tested this since setting up the failure scenario doesn't
seem trivial to configure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function changes ip_summed to CHECKSUM_NONE if CHECKSUM_COMPLETE
is set. This is called to discard checksum-complete when packet
is being modified and checksum is not pulled for headers in a layer.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the DRBG does not operate on shadow copies of the DRBG instance
any more, the cipher handles only need to be allocated once during
initalization time and deallocated during uninstantiate time.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The creation of a shadow copy is intended to only hold a short term
lock. But the drawback is that parallel users have a very similar DRBG
state which only differs by a high-resolution time stamp.
The DRBG will now hold a long term lock. Therefore, the lock is changed
to a mutex which implies that the DRBG can only be used in process
context.
The lock now guards the instantiation as well as the entire DRBG
generation operation. Therefore, multiple callers are fully serialized
when generating a random number.
As the locking is changed to use a long-term lock to avoid such similar
DRBG states, the entire creation and maintenance of a shadow copy can be
removed.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The drbg_generate returns 0 in success case. That means that
drbg_generate_long will always only generate drbg_max_request_bytes at
most. Longer requests will be truncated to drbg_max_request_bytes.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the documentation by including SEC1 into SEC2/3 doc
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We add a specific compatible for SEC1, to handle the differences
between SEC1 and SEC2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC1 bugs on 0 data hash, so we submit an already padded block representing 0 data
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC1 doesn't support scatter/gather, SEC1 doesn't handle link tables.
Therefore, for SEC1 we have to do it by SW. For that, we reserve
space at the end of the extended descriptor, in lieu of the space
reserved for the link tables on SEC2, and we perform sg_copy() when
preparing the descriptors
We also adapt the max buffer size which is only 32k on SEC1 while it
is 64k on SEC2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adapts the interrupts handling and reset function for
SEC1. On SEC1, registers are almost similar to SEC2+, but bits
are sometimes located at different places. So we need to define
TALITOS1 and TALITOS2 versions of some fields, and manage according
to whether it is SEC1 or SEC2.
On SEC1, only one interrupt vector is dedicated to the SEC, so only
interrupt_4ch is needed.
On SEC1, interrupts are enabled by clearing related bits in IMR,
while on SEC2, interrupts are enabled by seting the bits in IMR.
SEC1 also performs parity verification in the DES Unit. We have
to disable this feature because the test vectors provided in
the kernel have parity errors.
In reset functions, only SEC2 supports continuation after error.
For SEC1, we have to reset in all cases.
For errors handling, SEC2+ names have been kept, but displayed
text have been amended to reflect exact meaning on SEC1.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC 1.0, 1.2 and 2.x+ have different EU base addresses, so we need to
define pointers for each EU in the driver private data structure.
The proper address is set by the probe function depending on the
SEC type, in order to provide access to the proper address.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC1 descriptor is a bit different to SEC2+ descriptor.
talitos_submit() will have to copy hdr field into hdr1 field and
send the descriptor starting at hdr1 up to next_desc.
For SEC2, it remains unchanged and next_desc is just ignored.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
talitos descriptor is slightly different for SEC1 and SEC2+, so
lets the helper function that fills the descriptor take into account
the type of SEC.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We add a new feature in the features field, to mark compatible
"fsl,sec1.0"
We also define a helper function called has_ftr_sec1() to help
functions quickly determine if they are running on SEC1 or SEC2+.
When only SEC1 or SEC2 is compiled in, has_ftr_sec1() return
trivial corresponding value. If both are compiled in, feature
field is checked.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a CONFIG option to select SEC1, SEC2+ or both.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch enhances the talitos_desc struct with fields for SEC1.
SEC1 has only one header field, and has a 'next_desc' field in
addition.
This mixed descriptor will continue to fit SEC2, and for SEC1
we will recopy hdr value into hdr1 value in talitos_submit()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a helper function for reads and writes of the len
param of the talitos descriptor. This will help implement
SEC1 later.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
map_single_talitos_ptr() is always called with extent == 0, so lets remove this unused parameter
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
j_extent field is specific to SEC2 so we add a helper function to clear it
so that SEC1 can redefine that function as nop
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linux CodyingStyle recommends to use short variables for local
variables. ptr is just good enough for those 3 lines functions.
It helps keep single lines shorter than 80 characters.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch refactors the handling of the input and output data that is quite
similar in several functions
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Do use zero_entry value to init the descriptors ptrs to zero instead of
writing 0 in each field
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The buffer uses for temporary data must be cleared entirely. In AES192
the used buffer is drbg_statelen(drbg) + drbg_blocklen(drbg) as
documented in the comment above drbg_ctr_df.
This patch ensures that the temp buffer is completely wiped.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
backlog is not initialised so in the case where
cpg->eng_st != ENGINE_IDLE it is never initialised and
hence which could lead to an illegal memory dereference
in the statement:
backlog->complete(backlog, -EINPROGRESS);
Discovered with cppcheck static analsys:
[drivers/crypto/mv_cesa.c:616]:
(error) Uninitialized variable: backlog
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a3aV
-----END PGP SIGNATURE-----
Merge tag 'remoteproc-4.1-next' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc update from Ohad Ben-Cohen:
"Suman Anna is adding remoteproc support for processors not behind
IOMMUs"
* tag 'remoteproc-4.1-next' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: add IOMMU hardware capability flag
Pull misc kbuild updates:
"This is the remaining part of kbuild stuff for v4.1-rc1:
- One wew coccinelle script and a clarification of the proposed fix
in bugon.coccinelle
- CONFIG_KERNEL_LZ4 support for extract-ikconfig"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/coccinelle/misc/bugon.cocci: update bug_on conversion warning
scripts/extract-ikconfig: Support LZ4-compressed images.
irqf_oneshot.cocci: add check of devm_request_threaded_irq()
I'd like to say these were a set of regressions for the recent merge window
code. Unfortunately, they all predate the merge window code (stable cc'd).
There's two fixes for data integrity (mostly only showing up on module
removal), an mvsas crash with expander attached SATA devices which goes back
to the dawn of the driver but is only just being picked up as sas expanders
become a standard item in low end server hardware, an am53c974 one because the
interrupt data isn't fully initialised before the line is and a megaraid_sas
one because it uses smp_processor_id() to select MSI-X queues and that now
triggers a WARN_ON().
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVM+JoAAoJEDeqqVYsXL0My40H/Rtb85O+nLmsaPutyM3LqfNb
EKeF7voVsEp2uaNodx5xYe3Q3FpGW/dfct0uSrAD1fYWkr/z+9VJlYkh1dY0Z7Tq
FjbWufPWmRbqvk6q4C4bBkFRBKbX38cmdY9kJQgby6dqPXKhe0LKPJy+ik30b0HV
PWK6Voh3Y41zeOk/q4I2RvEREW+cCz1PTiQRP45Y1j+ilslmDGDH95KZ3PZPwE6t
xOfj9DpGBKmN5Fvn7mIPZA72Xpnmc3Zlw7gv8ZBctxpHRvO+woQXjRqORUEBu4bA
Cwg9lJnyRjDiTarm9ceCm8c5bmlii6Furfn/qxxnW9d64h4K1ed6lf0D/BehAdY=
=U1F+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"I'd like to say these were a set of regressions for the recent merge
window code. Unfortunately, they all predate the merge window code
(stable cc'd).
There are two fixes for data integrity (mostly only showing up on
module removal), an mvsas crash with expander attached SATA devices
which goes back to the dawn of the driver but is only just being
picked up as sas expanders become a standard item in low end server
hardware, an am53c974 one because the interrupt data isn't fully
initialised before the line is and a megaraid_sas one because it uses
smp_processor_id() to select MSI-X queues and that now triggers a
WARN_ON()"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mvsas: fix panic on expander attached SATA devices
am53c974: Fix crash during modprobe
megaraid_sas: use raw_smp_processor_id()
sd: Fix missing ATO tag check
sd: Unregister integrity profile
Pull drm updates from Dave Airlie:
"Highlights:
Core:
- Virtual GEM layer merged, this has been around for a long time, and
it provides a software backed device that allows userspace to use
it as a GEM shared memory handler. This makes it a lot easier to
do certain things when you have no GPU but still have to deal with
DRI expectations.
- atomic helper updates.
- framebuffer modifier interface added.
- i2c over auxch displayport fixes.
- fb width/height confusion fixes.
- new driver for ps8622/ps8625 bridge chips
- lots of new panels
i915:
- more plane atomic conversion
- vGPU guest support for XenGT
- Skylake workarounds and fixes
- Y-tiling support
- work on dynamic pagetable allocation
- EU count report param for gen9+
- CHV fixes (no longer prelim)
- remove ilk rc6
- frontbuffer tracking for fbc
- Displayport link rate refactoring
- sprite colorkey refactor
radeon:
- Displayport MST support (not enabled by default)
- non-ATOM native hw auxch support (DCE5+)
- output csc support
- new queries for userspace debug support
- new VCE packet
nouveau:
- gk20a iommu support
- gm107 graphics support
- more gm20x bringup (waiting on signed nvidia fw).
amdkfd:
- multiple kgd instance support
- use 64-bit time accessors
msm:
- stolen memory support
- DSI and dual-DSI support
- snapdragon 410 support
exynos:
- cleanups for atomic and pageflip
imx-drm:
- more media-bus formats
- TV output prep
- drm panel support
tegra:
- hw vblank counter using host1x syncpoints
omap:
- universal plane support
- prep work for atomic modesetting
rcar-du:
- ported to atomic modesetting
atmel-hlcdc:
- ported to atomic modesetting
- added suspend/resume support
sti:
- ported to atomic modesetting
dwhdmi:
- more compliant audio support
- update rockchip phy support
tda998x:
- DT probing for attached crtcs
- simplified EDID reading
rockchip:
- fixes
adv7511:
- fixes"
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (689 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
drm/i915: Dont enable CS_PARSER_ERROR interrupts at all
drm/i915: Move drm_framebuffer_unreference out of struct_mutex for takeover
drm: fix trivial typo mistake
drm: Make integer overflow checking cover universal cursor updates (v2)
drm/nouveau/bios: fix fetching from acpi on certain systems
drm/nouveau/gr/gm206: initial init+ctx code
drm/nouveau/ce/gm206: enable support via gm204 code
drm/nouveau/fifo/gm206: enable support via gm204 code
drm/nouveau/gr/gm204: initial init+ctx code
drm/nouveau: support for buffer moves via MaxwellDmaCopyA
drm/nouveau/ce/gm204: initial support
drm/nouveau: add support for gm20x fifo channels
drm/nouveau/fifo/gm204: initial support
drm/nouveau/gr/gk104-: prevent reading non-existent regs in intr handler
drm/nouveau/gr/gm107: very slightly demagic part of attrib cb setup
drm/nouveau/gr/gk104-: correct crop/zrop num_active_fbps setting
drm/nouveau/gr/gf100-: add symbolic names for classes
drm/nouveau/gr/gm107: support tpc "strand" ctxsw in gpccs ucode
drm/nouveau/gr/gf100-: support mmio access with gpc offset from gpccs ucode
...
As it turns out, the set_cs() enable parameter refers to the logic level
on the CS pin, not the state of chip selection.
This broke functionality of the LEDs behind the CPLD, or at least delayed
the commands until another one came in to toggle CS.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A pppoe session is identified by its session ID and MAC address.
Currently pppoe does not check if the received pkg has the correct
MAC address. This is a problem when the eth I/F is in promisc mode
as then any DST MAC address is accepted.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan says:
====================
iommu-common build warning fixes.
This patchset has fixes for 2 architectures
- Part 1: x86_64 warnings generated by sparse
- Part 2: allmodconfig build error for powerpc, identified by Guenter Roeck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_DEBUG_FORCE_WEAK_PER_CPU is set, the DEFINE_PER_CPU_SECTION
macro will define an extern __pcpu_unique_##name variable that could
conflict with the same definition in powerpc at this time. Avoid that
conflict by renaming iommu_pool_hash in iommu-common.c
Thanks to Guenter Roeck for catching this, and helping to test the fix.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial discussion was:
[FYI] xfrm: Don't lookup sk_policy for timewait sockets
Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.
This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.
v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not much this time, but the changes include:
* Moving domain allocation into the iommu drivers to prepare for
the introduction of default domains for devices
* Fixing the IO page-table code in the AMD IOMMU driver to
correctly encode large page sizes
* Extension of the PCI support in the ARM-SMMU driver
* Various fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FMxH
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Not much this time, but the changes include:
- moving domain allocation into the iommu drivers to prepare for the
introduction of default domains for devices
- fixing the IO page-table code in the AMD IOMMU driver to correctly
encode large page sizes
- extension of the PCI support in the ARM-SMMU driver
- various fixes and cleanups"
* tag 'iommu-updates-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (34 commits)
iommu/amd: Correctly encode huge pages in iommu page tables
iommu/amd: Optimize amd_iommu_iova_to_phys for new fetch_pte interface
iommu/amd: Optimize alloc_new_range for new fetch_pte interface
iommu/amd: Optimize iommu_unmap_page for new fetch_pte interface
iommu/amd: Return the pte page-size in fetch_pte
iommu/amd: Add support for contiguous dma allocator
iommu/amd: Don't allocate with __GFP_ZERO in alloc_coherent
iommu/amd: Ignore BUS_NOTIFY_UNBOUND_DRIVER event
iommu/amd: Use BUS_NOTIFY_REMOVED_DEVICE
iommu/tegra: smmu: Compute PFN mask at runtime
iommu/tegra: gart: Set aperture at domain initialization time
iommu/tegra: Setup aperture
iommu: Remove domain_init and domain_free iommu_ops
iommu/fsl: Make use of domain_alloc and domain_free
iommu/rockchip: Make use of domain_alloc and domain_free
iommu/ipmmu-vmsa: Make use of domain_alloc and domain_free
iommu/shmobile: Make use of domain_alloc and domain_free
iommu/msm: Make use of domain_alloc and domain_free
iommu/tegra-gart: Make use of domain_alloc and domain_free
iommu/tegra-smmu: Make use of domain_alloc and domain_free
...
Brian noticed while working on another SATA driver that uses libahci_platform,
an error in this driver; it tries to the the driver data for its
device, while libata also thinks it can set the driver data. See:
ahci_platform_init_host()
-> ata_host_alloc_pinfo()
-> ata_host_alloc()
-> dev_set_drvdata()
So instead of sticking the IP-specific platform data into drvdata, let's
use the plat_data variable that is reserved for this use.
Addtionally plat_data isn't set until ahci_platform_init_host() has been
called further down in probe(). So re-work the st_ahci_probe_resets and
st_ahci_deassert_resets functions to take ahci_host_priv *hpriv as a
parameter.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Suggested-by: Brian Norris <computersforpeace@gmail.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
With the recent changes omaps have developed a dependency to MFD_SYSCON.
This is used for system control module generic register area and some
clocks.
We do have it selected in omap2plus_defconfig, but targeted config
files may not have it selected. Let's make sure it's selected like
few other ARM platforms are already doing.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: Dudley Du <dudl@cypress.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which
is quite unexpected.
Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAgA
-----END PGP SIGNATURE-----
Merge tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
