return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wait_for_completion_timeout can be called with timeout == 0 due to
msecs_to_jiffies(2) == 1 for HZ < 1000 and usecs_to_jiffies(300) == 1
for all reasonable values of HZ, thus the following timeout /= 2; sets
timeout to 0. This patch simply adds a lower-bounds of 1.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up
in case of completion occurring the remaining time is >=1 so ret is set to
1 if no timeout occurred.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, is_sys_clk_from_pll check sysclk source by reading codec
register value. And it will be invoked before updating dapm widget
power. In some machine driver, snd_soc_dai_set_sysclk is called in
dapm event to switch codec sysclk to RC clock in idle mode. And in
some use cases (such as syspend/resume) hw_params will not be called
when the dapm widget is powered up. As a result, is_sys_clk_from_pll
will return 0 although it is supposed to be 1.
To solve this, we let is_sys_clk_from_pll check sysclk sysclk_src
which is stored in private data and don't change the value of sysclk_src
when codec sysclk is switched to internal clock. The internal clock
can only be used in idle mode, so it sould be fine if we don't set
sysclk_src to internal clock.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "Keep sysclk on if JD func is used" patch force enable/disable
pin in rt5670_set_dai_sysclk. But some machine driver call it in
dapm widget event. It will cause kernel crash.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
intel_mid_dma seems to be unmaintained for a long time. Moreover, the IP block
of DMA itself is the same in both dw_dmac and intel_mid_dma. This patch moves
spi-dw-midpci to use dw_dmac driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core has a comprehensive function set to map and unmap a message when it's
needed. This patch converts driver to use that advantage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch shuts up any ongoing DMA transfer in case of error.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In according to documentation SPI in DMA mode may encounter underrun/overrun
failures in rare cases. When such failure occurs, an error recovery protocol is
expected to be implemented in the device driver so that the failed transaction
can be restarted.
This patch enables FIFO overrun / underrun interrupts in DMA case and adds a
handler for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch splits DMA preparatory code to dma_setup() callback. The change also
converts transfer_one() to program DMA whenever the transfer is DMA mapped. The
change is a follow up of the converion to use SPI core transfer_one_message().
Since the DMA mapped transfers can be interleaved with PIO ones the DMA related
configuration should respect that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMAEngine has a specific type to be used for bus width. This patch converts the
code to use the values of the specific type when configure DMA transfer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jz4780 and jz4740 have very similar i2s blocks.
The slight difference is in Rx/Tx fifos.
And the bitclocks for input/output are different.
This patch adds jz4780 support to the driver
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove Kconfig dependency and enable driver for
all ARCHs.
Also update help description.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for setting the RSS hash table and hash key through ethtool.
This patch incorporates suggestions from Ben Hutchings
<ben.hutchings@codethink.co.uk>.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump PF version to 1.2.37 and VF version to 1.2.25
Change-ID: I0287a750408250dc055c03e1f744fd5f0caefd68
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print the LAN, SAN, and Port MACs for the VSI if debugfs command
dump VSI is used on the PF's VSI.
Example output:
[260221.871244] i40e 0000:04:00.0: MAC address: 68:05:ca:26:15:e0 SAN MAC: 00:00:00:00:02:00 Port MAC: 68:05:ca:26:15:e3
Change-ID: I0b393113dfb5ee7ff4f9e5227e4177885f0cc15e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes unused variables from lsiio.c in order
to get rid of the warnings regarding them.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Definition of _GNU_SOURCE is needed to get rid of some warnings, such
as:
warning: implicit declaration of function `asprintf'.
generic_buffer.c and iio_event_monitor.c define _GNU_SOURCE,
but it is also needed in lsiio.c and iio_utils.c. For this reason,
this patch adds the definition in Makefile and removes it from where
it already exists.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch moves iio userspace applications out of staging, to tools/iio/
and adds a Makefile in order to compile them easily. It also adds tools/iio/
to MAINTAINERS file.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch removes inline functions from iio_utils.h in order to clean the
code. iio_utils.c contains the implementation of the functions used by
iio_event_monitor.c, lsiio.c or generic_buffer.c and iio_utils.h contains
the declarations of these functions.
Since iio_utils.h is modified, generic_buffer.c and iio_event_monitor.c
must include stdlib.h.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
By adding this line and installing the kernel headers with
make headers_install, iio_event_monitor can be compiled without
any hacks.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This enables support of 'input-enable' pinconf generic property in
the pinctrl driver.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the pinctrl driver to use the generic pinconf
interface. Mainly it gives us a way to use debugfs to dump
group configurations.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no code ender the 'err' label. Just return the error code directly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct pinctrl_desc does not contain the maxpin member since commit 0d2006bbf0
(pinctrl: remove unnecessary max pin number).
Fixes: 0d2006bbf0 ('pinctrl: remove unnecessary max pin number')
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).
Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both nvidia,io-hv and nvidia,rcv-sel represent the fact that a particular
pin's IO buffers are configured to accept "high voltage" input signals.
The TRM for different chips names the register field rcv-sel on older
SoCs and io_hv on newer SoCs. Add the new naming option into the pinctrl
driver so that DT files can use naming consistent with the TRM.
This new property name will be documented in the patch that adds support
for the new SoC.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of the pinmux configuration bits that exist in "drive group"
registers in Tegra30..Tegra124 move to the "pinmux" registers on future
chips. Add a flag to support this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Various non-semantic tweaks and layout/consistency fixes for existing
Tegra pinctrl drivers.
Move the definition of DRV_PINGROUP_REG() before the definition of
PINGROUP() so that a future SoC driver can invoke the former from the
latter.
PINGROUP_BIT_Y(n) is just n, so replace it with n.
Re-wrap the parameters to *PINGROUP().
Keep various enums sorted in the Tegra124 driver.
Various white-space consistency fixes.
These changes aim to update existing drivers to be consistent with future
SoC drivers. While we could ignore these tweaks to the existing drivers,
I'd like to keep everything as consistent as possible for easy comparison.
Besides, I auto-generate the drivers, and maintaining special-cases to
keep the differences in place is annoying.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds the Device Tree binding documentation to describe the
pin-muxing controller of the Marvell Armada 39x processors. Two
variants are supported for the moment: the 88F6920 (Armada 390) and
88F6928 (Armada 398).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After the last user of the in_pd/in_pu bias parameters of the _PCRH()
macro was removed in commit 80da8e02d2 ("sh-pfc: r8a7740: Add bias
(pull-up/down) pinconf support"), bias parameters are supposed to be
configured using the generic pinctl mechanism, which calls the
.set_bias() method.
However, the PORTCR() macro still represents the control register as
consisting of two 4-bit fields. Hence the bias configuration in the
uppermost 2 bits is always overwritten with zeroes when a pin is
configured for GPIO, disabling any previously configured bias.
Use the variable config register macro instead, to represent the
register as having 4 fields, and to make sure only the input/output
control and function fields are touched.
This affects R-Mobile APE6 (r8a73a4), R-Mobile A1 (r8a7740), SH-Mobile
AP4 (sh7372), and SH-Mobile AG5 (sh73a0).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The r8a7791 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix build errors when CONFIG_THERMAL=m and SENSORS_PWM_FAN=y
by restricting SENSORS_PWM_FAN to 'm' when THERMAL=m.
drivers/built-in.o: In function `pwm_fan_remove':
pwm-fan.c:(.text+0x22ba58): undefined reference to `thermal_cooling_device_unregister'
drivers/built-in.o: In function `pwm_fan_probe':
pwm-fan.c:(.text+0x22bebb): undefined reference to `thermal_of_cooling_device_register'
pwm-fan.c:(.text+0x22bf11): undefined reference to `thermal_cdev_update'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Address the following sparse warnings.
drivers/hwmon/pwm-fan.c:176:5: warning:
symbol 'pwm_fan_of_get_cooling_data' was not declared. Should it be static?
drivers/hwmon/pwm-fan.c:176:5: warning:
no previous prototype for 'pwm_fan_of_get_cooling_data'
pwm_fan_of_get_cooling_data is only used in the pwm-fan driver and thus should
be declared static.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allow gpio-fan to be used as thermal cooling device for platforms that
use GPIO maps to control fans.
As part of this change, we make the shutdown and remove logic the same
as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The PWM FAN device can now be used as a thermal cooling device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch provides code for reading PWM FAN configuration data via
device tree. The pwm-fan can work with full speed when configuration
is not provided. However, errors are propagated when wrong DT bindings
are found.
Additionally the struct pwm_fan_ctx has been extended.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was necessary to decouple code handling writing to sysfs from the one
responsible for setting PWM of the fan.
Due to that, new __set_pwm() method was extracted, which is responsible for
only setting new PWM duty cycle.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some boards, such as the LaCie 2Big Network v2 or 2Big NAS (based on
Marvell Kirkwood SoCs), an I2C fan controller is used but the alarm
signal is wired to a separate GPIO. Unfortunately, the gpio-fan driver
can't be used to handle GPIO alarm alone from DT: an error is returned
if the "gpios" DT property is missing.
This patch allows to use the gpio-fan driver even if the "alarm-gpios"
DT property is defined alone.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bank register has five unused bits. Verify that those bits are zero
to strengthen the detect function.
Cc: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8603 only supports three fans, so it is not necessary to skip fan4.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8786E is mostly compatible with IT8771 / IT8772.
Parameters determined by testing various combinations.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Thomas Lorblanches <zlika_ese@hotmail.com>
[Guenter Roeck: merged from github, addressed review comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Newer chips don't typically support VID inputs or control.
Add a feature flag for VID support to simplify adding support for
new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fans 4-5 are not supported on all chips and revisions. Also, 16-bit fan
counters are always enabled on some chips. Provide feature flags to
simplify adding support for new chips.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>