Commit graph

533,096 commits

Author SHA1 Message Date
Prashant Laddha
d585c1e14a [media] vivid sdr: fix broken sine tone generated for sdr FM
FM (frequency modulated) signal for SDR is generated by varying the
phase, where phase variation is proportional to input signal. It is
seen that, the larger phase increments leads to discontinuities in
the signal recovered after demodulation. Reducing the extent of phase
variation with respect to input signal, equivalent to reducing the
modulation index.

Tested using FM receiver flow graph in gnuradio-companion.

Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:53:04 -03:00
Prashant Laddha
4e30a37345 [media] vivid sdr: Use LUT based implementation for sin/cos()
The common implementation for sin/cos in include/linux/fixp-arith.h
has been improved recently to provide higher precision.

Replacing native implementation of sin/cos in vivid sdr with common
implementation. This serves two purposes:

1. Improved accuracy: the native implementation based on the Taylor
   series is more prone to rounding errors.
2. Reuse of common function: this is better compared to maintaining
   native versions for each driver.

Suggested by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:51:32 -03:00
Mauro Carvalho Chehab
559addc25b [media] fixp-arith: replace sin/cos table by a better precision one
The cos table used at fixp-arith.h has only 8 bits of precision.
That causes problems if it is reused on other drivers.

As some media drivers require a higher precision sin/cos
implementation, replace the current implementation by one that
will provide 32 bits precision.

The values generated by the new implementation matches the
32 bit precision of glibc's sin for an angle measured in
integer degrees.

It also provides support for fractional angles via linear
interpolation. On experimental calculus, when used a table
with a 0.001 degree angle, the maximum error for sin is
0.000038, which is likely good enough for practical purposes.

There are some logic there that seems to be specific to the
usage inside ff-memless.c. Move those logic to there, as they're
not needed elsewhere.

Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:50:06 -03:00
Christian Engelmayer
96df988bb9 [media] cx88: Fix possible leak in cx8802_probe()
In case allocation vb2_dma_sg_init_ctx() fails during cx8802_probe(), the
already allocated cx8802 device structure memory is not freed in the used
exit path. Thus adapt the cleanup handling accordingly. Detected by Coverity
CID 1260065.

Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:47:19 -03:00
Alexey Khoroshilov
2160abb294 [media] sh_vou: fix memory leak on error paths in sh_vou_open()
Memory allocated for sh_vou_file is not deallocated
on error paths in sh_vou_open().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:46:48 -03:00
Hans Verkuil
6ab6a026bc [media] DocBook media: fix validation error
<tgroup> doesn't understand the 'border' attribute.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:46:16 -03:00
Kiran Padwal
92afdc1bf1 [media] staging: dt3155v4l: Switch to using managed resource with devm_
This patch uses managed resource APIs to allocate memory
in order to simplify the driver unload or failure cases

Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:45:57 -03:00
Geert Uytterhoeven
50d8e46faf [media] timberdale: VIDEO_TIMBERDALE should depend on HAS_DMA
If NO_DMA=y:

    warning: (VIDEO_OMAP2_VOUT && VIDEO_VIU && VIDEO_TIMBERDALE) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)

    drivers/built-in.o: In function `__videobuf_dc_free':
    videobuf-dma-contig.c:(.text+0x6f4d32): undefined reference to `dma_free_coherent'
    drivers/built-in.o: In function `__videobuf_dc_alloc':
    videobuf-dma-contig.c:(.text+0x6f4fe6): undefined reference to `dma_alloc_coherent'
    drivers/built-in.o: In function `__videobuf_mmap_mapper':
    videobuf-dma-contig.c:(.text+0x6f518e): undefined reference to `dma_free_coherent'

Commit 244829226f ("[media] timberdale: do not select TIMB_DMA")
dropped the dependency of VIDEO_TIMBERDALE on DMADEVICES, and thus the
implicit dependency on HAS_DMA.  VIDEO_TIMBERDALE selects
VIDEOBUF_DMA_CONTIG, which bypasses its dependency on HAS_DMA.  Make
VIDEO_TIMBERDALE depend on HAS_DMA to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:40:40 -03:00
Geert Uytterhoeven
a5d7c92c1b [media] am437x: VIDEO_AM437X_VPFE should depend on HAS_DMA
If NO_DMA=y:

    warning: (VIDEO_AM437X_VPFE && VIDEO_DM365_VPFE && VIDEO_DT3155 && VIDEO_OMAP4) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)

    drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
    drivers/media/v4l2-core/videobuf2-dma-contig.c:207: error: implicit declaration of function ‘dma_mmap_coherent’
    drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
    drivers/media/v4l2-core/videobuf2-dma-contig.c:390: error: implicit declaration of function ‘dma_get_sgtable’

VIDEO_AM437X_VPFE selects VIDEOBUF2_DMA_CONTIG, which bypasses its
dependency on HAS_DMA.  Make VIDEO_AM437X_VPFE depend on HAS_DMA to fix
this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:40:18 -03:00
Nicholas Mc Guire
9713883b0f [media] cx231xx: drop condition with no effect
The if and the else code are identical - so the condition has no effect
on the effective code.
This patch removes the condition and the duplicated code.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:39:32 -03:00
Tomeu Vizoso
dd30014908 ASoC: tegra: Add control for the Mic Jack pin
So userspace can enable and disable the external microphone.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 17:26:28 +00:00
Tomeu Vizoso
3a4562f756 ASoC: tegra: Add sink for the internal mic to tegra_max98090
Also adds a control for the pin of the internal mic, so userspace can
apply policy when the state of the external mic jack changes.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 17:26:28 +00:00
Tomeu Vizoso
a0cf43e2f0 ASoC: tegra: Expose Headphones pin to userspace
So userspace can enable or disable it based on the current policy.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 17:26:28 +00:00
Mark Brown
05a25fd53e Merge branch 'fix/rt5677' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-rt5677 2015-03-02 17:25:12 +00:00
Oder Chiou
cbca4076d1 ASoC: rt5677: Keep the LDO2 powered while used in the suspend mode
The patch keeps the ldo2 power while the DSP function of "Voice Wake Up" used
in the suspend mode.

Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 17:22:59 +00:00
Oder Chiou
ab1f70952f ASoC: rt5677: Add the chip type to distinguish the setting of the clock source
There is only one clock source in the rt5676, so the chip type is added to
distinguish the setting of the clock source in the VAD function.

Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 17:22:59 +00:00
Mauro Carvalho Chehab
f704eab5b6 [media] siano: avoid a linkedit error if !MC
If the media controller (MC) is not enabled, it will compile
fine, but will fail at the linkedition:

 ERROR: "media_device_unregister" [drivers/media/usb/siano/smsusb.ko] undefined!

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 14:17:01 -03:00
Vladimir Davydov
295458e672 cgroup: call cgroup_subsys->bind on cgroup subsys initialization
Currently, we call cgroup_subsys->bind only on unmount, remount, and
when creating a new root on mount. Since the default hierarchy root is
created in cgroup_init, we will not call cgroup_subsys->bind if the
default hierarchy is freshly mounted. As a result, some controllers will
behave incorrectly (most notably, the "memory" controller will not
enable hierarchy support). Fix this by calling cgroup_subsys->bind right
after initializing a cgroup subsystem.

Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2015-03-02 12:11:01 -05:00
Martin Hicks
29200f12a1 sata-fsl: Apply link speed limits
The driver was ignoring limits requested by libata.force.  The output
would look like:

fsl-sata ffe18000.sata: Sata FSL Platform/CSB Driver init
ata1: FORCE: PHY spd limit set to 1.5Gbps
ata1: SATA max UDMA/133 irq 74
ata1: Signature Update detected @ 0 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 310)

Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
2015-03-02 12:08:43 -05:00
Jason Low
283cb41f42 cpuset: Fix cpuset sched_relax_domain_level
The cpuset.sched_relax_domain_level can control how far we do
immediate load balancing on a system. However, it was found on recent
kernels that echo'ing a value into cpuset.sched_relax_domain_level
did not reduce any immediate load balancing.

The reason this occurred was because the update_domain_attr_tree() traversal
did not update for the "top_cpuset". This resulted in nothing being changed
when modifying the sched_relax_domain_level parameter.

This patch is able to address that problem by having update_domain_attr_tree()
allow updates for the root in the cpuset traversal.

Fixes: fc560a26ac ("cpuset: replace cpuset->stack_list with cpuset_for_each_descendant_pre()")
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Jason Low <jason.low2@hp.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Serge Hallyn <serge.hallyn@canonical.com>
2015-03-02 11:55:04 -05:00
Zefan Li
79063bffc8 cpuset: fix a warning when clearing configured masks in old hierarchy
When we clear cpuset.cpus, cpuset.effective_cpus won't be cleared:

  # mount -t cgroup -o cpuset xxx /mnt
  # mkdir /mnt/tmp
  # echo 0 > /mnt/tmp/cpuset.cpus
  # echo > /mnt/tmp/cpuset.cpus
  # cat cpuset.cpus

  # cat cpuset.effective_cpus
  0-15

And a kernel warning in update_cpumasks_hier() is triggered:

 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 4028 at kernel/cpuset.c:894 update_cpumasks_hier+0x471/0x650()

Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Serge Hallyn <serge.hallyn@canonical.com>
2015-03-02 11:55:04 -05:00
Zefan Li
790317e1b2 cpuset: initialize effective masks when clone_children is enabled
If clone_children is enabled, effective masks won't be initialized
due to the bug:

  # mount -t cgroup -o cpuset xxx /mnt
  # echo 1 > cgroup.clone_children
  # mkdir /mnt/tmp
  # cat /mnt/tmp/
  # cat cpuset.effective_cpus

  # cat cpuset.cpus
  0-15

And then this cpuset won't constrain the tasks in it.

Either the bug or the fix has no effect on unified hierarchy, as
there's no clone_chidren flag there any more.

Reported-by: Christian Brauner <christianvanbrauner@gmail.com>
Reported-by: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Serge Hallyn <serge.hallyn@canonical.com>
2015-03-02 11:55:04 -05:00
Colin Ian King
ee655c2968 dmaengine: s3c24xx: Fix spelling mistake in dev_err mistake
Fix spelling mistake, "aquire" -> "acquire" and missing newline (as
spotted by Joe Perches.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-03-02 22:18:57 +05:30
Geert Uytterhoeven
b6d1778bc5 dmaengine: shdma: Move DMA stop to (runtime) suspend callbacks
During system reboot, the sh-dma-engine device may be runtime-suspended,
causing a crash:

    Unhandled fault: imprecise external abort (0x1406) at 0x0002c02c
    Internal error: : 1406 [#1] SMP ARM
    ...
    PC is at sh_dmae_ctl_stop+0x28/0x64
    LR is at sh_dmae_ctl_stop+0x24/0x64

If the sh-dma-engine is runtime-suspended, its module clock is turned
off, and its registers cannot be accessed.

To fix this, move the call to sh_dmae_ctl_stop(), which touches the
DMAOR register, to the sh_dmae_suspend() and sh_dmae_runtime_suspend()
callbacks.  This makes PM operations more symmetric, as both
sh_dmae_resume() and sh_dmae_runtime_resume() already call sh_dmae_rst()
to re-initialize the DMAOR register.

Remove sh_dmae_shutdown(), as it became empty.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2015-03-02 22:10:44 +05:30
Josh Wu
ce037f19aa [media] media: atmel-isi: increase the burst length to improve the performance
The burst length could be BEATS_4/8/16. Before this patch, isi use default
value BEATS_4. To imporve the performance we could set it to BEATS_16.

Otherwise sometime it would cause the ISI overflow error.

Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 13:27:11 -03:00
Mengdong Lin
ea232b3f72 ASoC: rt5670: add API to select ASRC clock source
When codec is in slave mode, ASRC can suppress noise for asynchronous
MCLK and LRCLK or special I2S format. This patch defines an API to select
the clock source for specified filters.  And the codec driver will turn on ASRC
for these filters if ASRC is selected as their clock source.

Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 16:19:46 +00:00
Bard Liao
3aebec3a70 ASoC: rt5670: redefine ASRC control registers 0x84 and 0x85
The previous definition of registers 0x84 and 0x85 doesn't match the datasheet.
So this patch removes the wrong definition and writes a new one for the two
registers.

Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 16:19:46 +00:00
Bard Liao
77e3ea2801 ASoC: rt5670: Keep sysclk on if JD func is used
System clock is necessary for rt5670 JD function. We assume system
clock source will be set in machine driver. So there are two things
left we should do in codec driver.
1. Set sysclk to codec internal clock in probe since machine driver
   may not do that before JD function is registered.
2. Power up PLL once sysclk source is switched to PLL.

Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 16:19:46 +00:00
Bard Liao
64e89e5f55 ASoC: rt5670: Add runtime PM support
This patch adds runtime PM support on rt5670 codec.

Signed-off-by: Lin Mengdong <mengdong.lin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 16:19:46 +00:00
Bard Liao
223c055aa0 ASoC: rt5670: set platform data by dmi
This patch set specific data according to dmi data.

Signed-off-by: Jin, Yao <yao.jin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 16:19:46 +00:00
Alexandre Belloni
d7a6fe015b ASoC: sam9g20_wm8731: drop machine_is_xxx
Atmel based boards can now only be used with device tree. Drop non DT
initialization.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-02 16:19:26 +00:00
Adrian Hunter
543d976fa2 perf tools: Initialize cpu set in pthread_attr_setaffinity_np feature test
Feature tests are compiled but not executed, however it might avoid a
future uninitialized variable warning, so initialize the cpu set.

Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-tip-commits@vger.kernel.org
Link: http://lkml.kernel.org/r/54F41849.1010906@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:48:16 -03:00
Masami Hiramatsu
0104fe69e0 perf probe: Remove bias offset to find probe point by address
Remove bias offset to find probe point by address.

Without this patch, probe points on kernel and executables are shown
correctly, but do not work with libraries:

  # ./perf probe -l
    probe:do_fork        (on do_fork@kernel/fork.c)
    probe_libc:malloc    (on malloc in /usr/lib64/libc-2.17.so)
    probe_perf:strlist__new (on strlist__new@util/strlist.c in /home/mhiramat/ksrc/linux-3/tools/perf/perf)

Removing bias allows it to show it as real place:

  # ./perf probe -l
    probe:do_fork        (on do_fork@kernel/fork.c)
    probe_libc:malloc    (on __libc_malloc@malloc/malloc.c in /usr/lib64/libc-2.17.so)
    probe_perf:strlist__new (on strlist__new@util/strlist.c in /home/mhiramat/ksrc/linux-3/tools/perf/perf)

Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naohiro Aota <naota@elisp.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150302124946.9191.64085.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:34:38 -03:00
Masami Hiramatsu
79702f6141 perf probe: Warn if given uprobe event accesses memory on older kernel
Warn if given uprobe event accesses memory on older kernel.

Until 3.14, uprobe event only supports accessing registers so this warns
to upgrade kernel if uprobe-event returns -EINVAL and an argument of the
event accesses memory ($stack, @+offset, and +|-offs() symtax).

With this patch (on 3.10.0-123.13.2.el7.x86_64);
  -----
  # ./perf probe -x ./perf warn_uprobe_event_compat stack=-0\(%sp\)
  Added new event:
  Failed to write event: Invalid argument
  Please upgrade your kernel to at least 3.14 to have access to feature -0(%sp)
    Error: Failed to add events.
  -----

Suggested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20150228025329.32106.70581.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:27:43 -03:00
Ingo Molnar
de5349fa43 perf tools: Improve 'libbabel' feature check failure message
On Debian-ish systems libbabeltrace-dev should be suggested as a package
install as well.

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <david.ahern@oracle.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150228091849.GA28959@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:21:41 -03:00
Ingo Molnar
b49f1a4be7 perf tools: Improve feature test debuggability
Certain feature tests fail with link errors:

  triton:~/tip/tools/perf/config/feature-checks> make test-libbabeltrace.bin
  gcc -MD  -o test-libbabeltrace.bin test-libbabeltrace.c # -lbabeltrace provided by
  /tmp/cc6dRSqd.o: In function `main':
  test-libbabeltrace.c:(.text+0xf): undefined reference to `bt_ctf_stream_class_get_packet_context_type'

although they should already fail with a build error due to lack of a
proper prototype for the function. Due to this I first tried to find
which library was missing - while it was the whole feature that was
missing from the .h file already.

To solve this, propagate -Wall -Werror to all testcases and remove them
from testcase Makefile rules that used them explicitly.

A missing feature now outputs:

  triton:~/tip/tools/perf/config/feature-checks> make test-libbabeltrace.bin
  gcc -MD  -Wall -Werror -o test-libbabeltrace.bin test-libbabeltrace.c  # -lbabeltrace provided by
  test-libbabeltrace.c: In function ‘main’:
  test-libbabeltrace.c:6:2: error: implicit declaration of function ‘bt_ctf_stream_class_get_packet_context_type’ [-Werror=implicit-function-declaration]

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <david.ahern@oracle.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150228091627.GF31887@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:17:44 -03:00
Ingo Molnar
0189d7c45a perf tools: Improve libbfd detection message
Before:

  No bfd.h/libbfd found, install binutils-dev[el]/zlib-static to gain symbol demangling

After:

  No bfd.h/libbfd found, please install binutils-dev[el]/zlib-static/libiberty-dev to gain symbol demangling

Change the message to the standard 'please install' language and also
add libiberty-dev suggestion for Ubuntu systems.

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <david.ahern@oracle.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150228084610.GE31887@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:16:35 -03:00
Ingo Molnar
a954e68402 perf tools: Improve libperl detection message
Before:

  Missing perl devel files. Disabling perl scripting support, consider installing perl-ExtUtils-Embed

After:

  Missing perl devel files. Disabling perl scripting support, please install perl-ExtUtils-Embed/libperl-dev

Change the message to the standard 'please install' language and
adds Debian-ish package suggestion.

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <david.ahern@oracle.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150228083909.GC31887@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:15:55 -03:00
Ingo Molnar
6c5aa23704 perf tools: Improve Python feature detection messages
Change the Python detection message from:

  config/Makefile:566: No python-config tool was found
  config/Makefile:566: Python support will not be built

  config/Makefile:565: No 'python-config' tool was found: disables Python support - please install python-devel/python-dev

It's now a standard one-line message with a package install suggestion,
and it also uses the standard language used by other feature detection
messages.

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <david.ahern@oracle.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150228083345.GB31887@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:13:51 -03:00
Ingo Molnar
a6a76ba9ea perf tools: Remove annoying extra message from the features build
This message:

  Makefile:153: The path 'python-config' is not executable.

Appears on every perf build that does not have a sufficient python
environment installed. It's really just an internal detail of python
configuration pass and users should not see it - and it's pretty
meaningless to them in any case because the message is not very helpful.
(So it's not executable. Why does that matter? What can the user do
about it?)

Remove the warning, the missing python feature warning is sufficient:

  config/Makefile:566: No python-config tool was found
  config/Makefile:566: Python support will not be built

although even that one isn't very helpful to users: so no Python support
will be built, what can the user do to fix that? Most other such
warnings give package install suggestions.

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <david.ahern@oracle.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150228081750.GA31887@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:07:35 -03:00
Ingo Molnar
97fe925359 perf tools: Add PERF-FEATURES to the .gitignore file
It's an auto-generated file.

Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <david.ahern@oracle.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150228081248.GA31856@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:06:20 -03:00
Namhyung Kim
9a75606ca0 perf record: Document --group option
The 'perf record --group' option lacks documentation and confuses users.
As -e/--event option already supports group spec, it should not be used
anymore.

Also add a short description of event group itself.

Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1425266013-5034-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:04:45 -03:00
Namhyung Kim
08b23f4e63 perf record: Get rid of -l option from Documentation
The perf record does not support -l option anymore, so nuke it.

Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1425272038-10406-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:04:07 -03:00
Namhyung Kim
b11db6581b perf tools: Fix build error on ARCH=i386/x86_64/sparc64
He Kuang reported that current perf tools failed to build when ARCH
variable was given like above.

It was because the name is different that internal directory name.  I
can see that David's sparc64 build has same problem.

So fix it by applying the sed conversion script to the command line ARCH
variable also, and fixing the converted name there (i.e. i386/x86_64 ->
x86, sparc64 -> sparc).

Reported-by: He Kuang <hekuang@huawei.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: He Kuang <hekuang@huawei.com>
Acked: Jiri Olsa <jolsa@redhat.com>
Cc: David Ahern <david.ahern@oracle.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1425270663-10215-1-git-send-email-namhyung@kernel.org
[ Resolved conflict with 4861f87cd3 "Make sparc64 arch point to sparc" ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2015-03-02 12:01:42 -03:00
Rafał Miłecki
9b6cc9a807 bcma: enable support for PCIe Gen 2 host devices
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-02 16:59:45 +02:00
Rafał Miłecki
804e27dee4 bcma: support bringing up bus hosted on PCIe Gen 2
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-02 16:59:45 +02:00
Rafał Miłecki
5b6ff664c8 bcma: change IRQ control function to accept bus as an argument
It doesn't operate on PCI core, but PCI host device, so there is no
point of passing core related struct.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-02 16:59:45 +02:00
Rafał Miłecki
4186721d02 bcma: add helpers bringing PCIe hosted bus up / down
Bringing PCIe hosted bus up requires operating on host-related core.
Since we plan to support PCIe Gen 2 devices we should provide a helper
picking the correct one (PCIE or PCIE2).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-02 16:59:45 +02:00
Hans Verkuil
0e66100637 [media] vb2: fix 'UNBALANCED' warnings when calling vb2_thread_stop()
Stopping the vb2 thread (as used by several DVB devices) can result
in an 'UNBALANCED' warning such as this:

vb2: counters for queue ffff880407ee9828: UNBALANCED!
vb2:     setup: 1 start_streaming: 1 stop_streaming: 1
vb2:     wait_prepare: 249333 wait_finish: 249334

This is due to a race condition between stopping the thread and
calling vb2_internal_streamoff(). While I have not been able to deduce
the exact mechanism how this race condition can produce this warning,
I can see that the way the stream is stopped is likely to lead to a
race somewhere.

This patch simplifies how this is done by first ensuring that the
thread is completely stopped before cleaning up the vb2 queue. It
does that by setting threadio->stop to true, followed by a call to
vb2_queue_error() which will wake up the thread. The thread sees that
'stop' is true and it will exit.

The call to kthread_stop() waits until the thread has exited, and only
then is the queue cleaned up by calling __vb2_cleanup_fileio().

This is a much cleaner sequence and the warning has now disappeared.

Reported-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Tested-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org>      # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
2015-03-02 11:59:36 -03:00
Rafał Miłecki
ba8b6ae6e9 brcmfmac: respect reason when deleting (deauthenticating) STA
Starting with kernel 3.19 reason is provided by cfg80211.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-03-02 16:57:28 +02:00