The sending part is split in two functions to make sure
atomicity of the operations, such as the MD superblock update.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
1. receive status
sender receiver receiver
ACK:CR ACK:CR ACK:CR
2. sender get EX of TOKEN
sender get EX of MESSAGE
sender receiver receiver
TOKEN:EX ACK:CR ACK:CR
MESSAGE:EX
ACK:CR
3. sender write LVB.
sender down-convert MESSAGE from EX to CR
sender try to get EX of ACK
[ wait until all receiver has *processed* the MESSAGE ]
[ triggered by bast of ACK ]
receiver get CR of MESSAGE
receiver read LVB
receiver processes the message
[ wait finish ]
receiver release ACK
sender receiver receiver
TOKEN:EX MESSAGE:CR MESSAGE:CR
MESSAGE:CR
ACK:EX
4. sender down-convert ACK from EX to CR
sender release MESSAGE
sender release TOKEN
receiver upconvert to EX of MESSAGE
receiver get CR of ACK
receiver release MESSAGE
sender receiver receiver
ACK:CR ACK:CR ACK:CR
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
The DLM informs us in case of node failure with the DLM slot number.
cluster_info->recovery_map sets the bit corresponding to the slot number
and wakes up the recovery thread.
The recovery thread:
1. Derives the slot number from the recovery_map
2. Locks the bitmap corresponding to the slot
3. Copies the set bits to the node-local bitmap
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
bitmap_copy_from_slot reads the bitmap from the slot mentioned.
It then copies the set bits to the node local bitmap.
This is helper function for the resync operation on node failure.
bitmap_set_memory_bits() currently assumes it is only run at startup and that
they bitmap is currently empty. So if it finds that a region is already
marked as dirty, it won't mark it dirty again. Change bitmap_set_memory_bits()
to always set the NEEDED_MASK bit if 'needed' is set.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
When a PCM draining is performed to an empty stream that has been
already in PREPARED state, the current code just ignores and leaves as
it is, although the drain is supposed to set all such streams to SETUP
state. This patch covers that overlooked case.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When querying the GTFIFOCTL register to check the FIFO space, the read value
must be masked. The operation is repeated explicitly in several places. This
change refactors the read-and-mask code into a function call.
v2: rebased on top of Mika's forcewake patch set, specifically:
[PATCH 8/8] drm/i915: Enum forcewake domains and domain identifiers
Change-Id: Id1a9f3785cb20b82d4caa330c37b31e4e384a3ef
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Export 32-bit version of memcpy for use in suspend/resume.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for platform suspend and resume. We ensure all pcms are
suspended by invoking snd_soc_suspend() and then stop the DSP
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver didn't implement support for pcm stream suspend and resume, so
add it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds missing pcm pause and resume ops in the driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The updated firmware expects the MMX ID to be used as 3, so update the
driver as well
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP messages are sent with nonatomic context, which include trigger
messages, so mark the driver as nonatomic
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA core with commit 257f8cce5d - "ALSA: pcm: Allow nonatomic trigger
operations" allows trigger ops to implemented as nonatomic. For ASoC, we can
specify this in dailinks and is updated while snd_pcm is created
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch will fix below sparse warnings
warning: incorrect type in argument 2 (different base types) expected
unsigned int [unsigned] val got restricted snd_pcm_format_t [usertype]
<noident>
sound/soc/intel/haswell.c:61:37
sound/soc/intel/broadwell.c:115:37:
sound/soc/intel/bytcr_dpcm_rt5640.c:118:37:
sound/soc/intel/cht_bsw_rt5672.c:183:37:
sound/soc/intel/cht_bsw_rt5645.c:208:37:
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a helper to set pcm format directly from params
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The manual recommends that we reset the DSP when we suspend so add that in
runtime suspend handler
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IPC driver saved only IMR register, we need to save the CSR as well, so
add it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The updated firmware expects the MMX ID to be used as 3, so update the
driver as well
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "Extended Compat ID OS Feature Descriptor Specification" does not
require the (sub)compatible ids to be NUL-terminated, because they
are placed in a fixed-size buffer and only unused parts of it should
contain NULs. If the buffer is fully utilized, there is no place for NULs.
Consequently, the code which uses desc->ext_compat_id never expects the
data contained to be NUL terminated.
If the compatible id is stored after sub-compatible id, and the compatible
id is full length (8 bytes), the (useless) NUL terminator overwrites the
first byte of the sub-compatible id.
If the sub-compatible id is full length (8 bytes), the (useless) NUL
terminator ends up out of the buffer. The situation can happen in the RNDIS
function, where the buffer is a part of struct f_rndis_opts. The next
member of struct f_rndis_opts is a mutex, so its first byte gets
overwritten. The said byte is a part of a mutex'es member which contains
the information on whether the muext is locked or not. This can lead to a
deadlock, because, in a configfs-composed gadget when a function is linked
into a configuration with config_usb_cfg_link(), usb_get_function()
is called, which then calls rndis_alloc(), which tries locking the same
mutex and (wrongly) finds it already locked.
This patch eliminates NUL terminating of the (sub)compatible id.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: da4243145f: "usb: gadget: configfs: OS Extended Compatibility descriptors support"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the wrapper the IRQ disable should be done by writing 1's to the
IRQ*_CLR register. Existing code is broken because it instead writes
zeros to IRQ*_SET register.
Fix this by adding functions dwc3_omap_write_irqmisc_clr() and
dwc3_omap_write_irq0_clr() which do the right thing.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_v4l2.c:264:29: warning: symbol 'uvc_v4l2_ioctl_ops' was not declared. Should it be static?
uvc_v4l2.c:355:29: warning: symbol 'uvc_v4l2_fops' was not declared. Should it be static?
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
g_ffs.c:136:3: warning: symbol 'gfs_configurations' was not declared. Should it be static?
g_ffs.c:281:16: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
uvc_video.c:283:5: warning: symbol 'uvcg_video_pump' was not declared. Should it be static?
uvc_video.c:342:5: warning: symbol 'uvcg_video_enable' was not declared. Should it be static?
uvc_video.c:381:5: warning: symbol 'uvcg_video_init' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_sourcesink.c:347:34: warning: symbol 'ss_int_source_comp_desc' was not declared. Should it be static?
f_sourcesink.c:365:34: warning: symbol 'ss_int_sink_comp_desc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warnings:
f_uac2.c:57:12: warning: symbol 'uac2_name' was not declared. Should it be static?
f_uac2.c:637:36: warning: symbol 'in_clk_src_desc' was not declared. Should it be static?
f_uac2.c:649:36: warning: symbol 'out_clk_src_desc' was not declared. Should it be static?
f_uac2.c:661:39: warning: symbol 'usb_out_it_desc' was not declared. Should it be static?
f_uac2.c:675:39: warning: symbol 'io_in_it_desc' was not declared. Should it be static?
f_uac2.c:689:40: warning: symbol 'usb_in_ot_desc' was not declared. Should it be static?
f_uac2.c:703:40: warning: symbol 'io_out_ot_desc' was not declared. Should it be static?
f_uac2.c:716:34: warning: symbol 'ac_hdr_desc' was not declared. Should it be static?
f_uac2.c:754:34: warning: symbol 'as_out_hdr_desc' was not declared. Should it be static?
f_uac2.c:767:38: warning: symbol 'as_out_fmt1_desc' was not declared. Should it be static?
f_uac2.c:775:32: warning: symbol 'fs_epout_desc' was not declared. Should it be static?
f_uac2.c:785:32: warning: symbol 'hs_epout_desc' was not declared. Should it be static?
f_uac2.c:831:34: warning: symbol 'as_in_hdr_desc' was not declared. Should it be static?
f_uac2.c:844:38: warning: symbol 'as_in_fmt1_desc' was not declared. Should it be static?
f_uac2.c:852:32: warning: symbol 'fs_epin_desc' was not declared. Should it be static?
f_uac2.c:862:32: warning: symbol 'hs_epin_desc' was not declared. Should it be static?
f_uac2.c:1566:21: warning: symbol 'afunc_alloc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch fixes following sparse warning:
f_hid.c:572:30: warning: symbol 'f_hidg_fops' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit exposes in sysfs the HID country code that is stored in the country
member of hid_device structure. It identifies the country code of localized
hardware.
For example some keyboards use it to exhibit the language of the key layout. It
helps the upper layer to identify the localized hardware and setup the correct
language to use.
For USB HID devices the country code comes for the HID descriptor and for
Bluetooth HID devices it is the HIDCountryCode attribute from the SDP database.
Signed-off-by: Olivier Gay <ogay@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We still have a combination of legacy phys and generic phys in
use so we need to support both types of phy for musb_dsps.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The renesas usbhs driver calls extcon_get_edev_by_phandle(), which
is defined in drivers/extcon/extcon-class.c, and that can be a
loadable module. If the extcon-class support is disabled, usbhs
will work correctly for all devices that do not need extcon.
However, if extcon-class is a loadable module, and usbhs is
built-in, the kernel fails to link. In order to solve that,
we need a Kconfig dependency that allows extcon to be disabled
but does not allow usbhs built-in if extcon is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The value for the multipoint dts property is ignored when parsing with
of_property_read_bool, so we currently have multipoint always set as 1
even if value 0 is specified in the dts file.
Let's fix this to read the value too instead of just the property like
the binding documentation says as otherwise MUSB will fail to work
on devices with Mentor configuration that does not support multipoint.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AFAICS, there is no reason why kernel threads should have FPU context
even if use_eager_fpu() == T. Now that interrupted_kernel_fpu_idle()
does not check __thread_has_fpu() in the use_eager_fpu() case, we
can remove the init_fpu() code from eager_fpu_init() and change
flush_thread() called by do_execve() to initialize FPU.
Note: of course, the change in flush_thread() is horrible and must be
cleanuped. We need the new helper, and flush_thread() should return the
error if init_fpu() fails.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/20150119185212.GD16427@redhat.com
Signed-off-by: Borislav Petkov <bp@suse.de>
The __thread_has_fpu() check in interrupted_kernel_fpu_idle() was needed
to prevent the nested kernel_fpu_begin(). Now that we have in_kernel_fpu
and !__thread_has_fpu() case in __kernel_fpu_begin() does not depend on
use_eager_fpu() (except clts) we can remove it.
__thread_has_fpu() can be false even if use_eager_fpu(), but this case
does not differ from !use_eager_fpu() case except we should not worry
about X86_CR0_TS, __kernel_fpu_begin()/end() will not touch this bit.
Note: I think we can kill all irq_fpu_usable() checks except in_kernel_fpu,
just we need to record the state of X86_CR0_TS in __kernel_fpu_begin() and
conditionalize stts() in __kernel_fpu_end(), but this needs another patch.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Link: http://lkml.kernel.org/r/20150119185151.GC16427@redhat.com
Signed-off-by: Borislav Petkov <bp@suse.de>
__kernel_fpu_begin() does nothing if !__thread_has_fpu() && use_eager_fpu(),
perhaps it assumes that this case is simply impossible. This is certainly
not possible if in_interrupt() == T; interrupted_user_mode() should have
FPU, and interrupted_kernel_fpu_idle() should fail if !__thread_has_fpu().
However, even if use_eager_fpu() == T a task can do drop_fpu(), then switch
to another thread which becomes fpu_owner_task, then resume and call some
function which does kernel_fpu_begin(). Say, an exiting task does a lot of
things after exit_thread(), it is not safe to assume that it can't use FPU
in these paths.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Pekka Riikonen <priikone@iki.fi>
Link: http://lkml.kernel.org/r/20150119185132.GB16427@redhat.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Even without an iommu, NO_KERNEL_MAPPING is still convenient to save on
kernel address space in places where we don't need a kernel mapping.
Implement support for it in the two places where we're creating an
expensive mapping.
__alloc_from_pool uses an internal pool from which we already have
virtual addresses, so it's not relevant, and __alloc_simple_buffer uses
alloc_pages, which will always return a lowmem page, which is already
mapped into kernel space, so we can't prevent a mapping for it in that
case.
Signed-off-by: Jasper St. Pierre <jstpierre@mecheye.net>
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Drake <dsd@endlessm.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The pci_mmap_page_range() API should be written to expect offset
values representing PCI memory resource addresses as seen by user
space, through the pci_resource_to_user() API.
ARM relies on the standard implementation of pci_resource_to_user()
which actually is an identity map and exports to user space
PCI memory resources as they are stored in PCI devices resources
structures, which represent CPU physical addresses (fixed-up using
BUS to CPU address conversions) not PCI bus addresses.
Therefore, on ARM platforms where the mapping between CPU and BUS
address is not a 1:1 the current pci_mmap_page_range() implementation is
erroneous, in that an additional shift is applied to an already fixed-up
offset passed from userspace.
Hence, this patch removes the mem_offset from the pgoff calculation
since the offset as passed from user space already represents the CPU
physical address corresponding to the resource to be mapped, ie no
additional offset should be applied.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, interworking calls on module boundaries are not supported,
and are handled by the same error handling code path as non-interworking
calls whose targets are simply out of range.
Before modifying the handling of those out-of-range jump and call
relocations in a subsequent patch, move the handling of interworking
restrictions out of it.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change:
7b8792bbdf
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
assumed that only one gpio-chip is registred per of-node.
Some drivers register more than one chip per of-node, so
adjust the matching function of_gpiochip_find_and_xlate to
not stop looking for chips if a node-match is found and
the translation fails.
Cc: Stable <stable@vger.kernel.org>
Fixes: 7b8792bbdf ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags")
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Tyler Hall <tylerwhall@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To figure out if ordered_events are being used when doing a flush
operation, it is enough to check if there were in fact some events
queued, i.e. look at oe->nr_events.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-1c5r404vy766kt5nflv88uag@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Microsoft Natural Wireless Ergonomic Keyboard 7000 has special My
Favorites 1..5 keys which are handled through a vendor-defined usage
page (0xff05).
Apply MS_ERGONOMY quirks handling to USB PID 0x071d (Microsoft Microsoft
2.4GHz Transceiver V1.0) so that the My Favorites 1..5 keys are reported
as KEY_F14..18 events.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=52841
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current API only allows setting one offset in the field. This API
is extended to set multiple offsets in the field report.
Also update parameters in the users of this API.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some hid sensor feature report can contain more than one reports.
This API can now support receiving multiple values from the feature
report.
Also update the parameters in the users of this API.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Device Tree description of SDHCI on Armada 388 RD board was
missing. This commit adds the node for it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The binding of the armada-380-sdhci has been extended with a new
register in order to be able to use the SDR50 and DDR50 mode. This
commit add the resource associated to this new register for the
Armada 38x.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 38x SDHCI node.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pass the requested load directly to the rpm.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>