It seems Broadcom released two devices with conflicting device id. There
are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they
can be found in routers, e.g. Netgear WNR834Bv2. However, according to
Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY).
It's unsure if they meant PCI device id, or "virtual" id (from SPROM).
To distinguish these devices lets check PHY type (G vs. N).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As we plan to add support for platform NVRAM we should store direct
data pointer without the extra struct firmware layer. This will allow
us to support other sources with the only requirement being u8 buffer.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most drivers use FIF_OTHER_BSS to set promiscous mode. Let us
follow their lead even though it doesn't match exactly the HW
filter flags.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure .disconnect() doesn't cleanup the device if
.resume() failed. This may happen when device is removed
during suspend.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Users of older Ralink devices report that received frames
sometimes have zero length. Watch out for that.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows e.g. user space to use /sys/class/ieee80211/*/macaddress
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently Broadcom added support for NVRAMs with entries for multiple
PCIe devices. One of the supported formats is based on prefixes defined
like: devpath0=pcie/1/4/ and entries like 0:foo=bar 0:baz=qux etc.
Unfortunately there are also a bit older devices using different way of
defining prefixes, e.g. SmartRG SR400ac (2 x BCM43602) with entries:
devpath0=pci/1/1/
devpath1=pci/2/1
Broadcom stated this old format will never be used/supported by brcmfmac
but given the simplicity of this patch I'll insist on supporting it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kernel is not trying to increase mcbufsz. It suggests you should try
doing so. Also print the calculated required size of mcbufsz.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rework slave configuration part in order to more report wrong errors
about the configuration.
Only maxburst and addr width values are checked when doing the slave
configuration. The validity of the channel configuration is done at
prepare time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Using _bh variant for spin locks causes this kind of warning:
Starting logging: ------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at /ssd_drive/linux/kernel/softirq.c:151
__local_bh_enable_ip+0xe8/0xf4()
Modules linked in:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.1.0-rc2+ #94
Hardware name: Atmel SAMA5
[<c0013c04>] (unwind_backtrace) from [<c00118a4>] (show_stack+0x10/0x14)
[<c00118a4>] (show_stack) from [<c001bbcc>]
(warn_slowpath_common+0x80/0xac)
[<c001bbcc>] (warn_slowpath_common) from [<c001bc14>]
(warn_slowpath_null+0x1c/0x24)
[<c001bc14>] (warn_slowpath_null) from [<c001e28c>]
(__local_bh_enable_ip+0xe8/0xf4)
[<c001e28c>] (__local_bh_enable_ip) from [<c01fdbd0>]
(at_xdmac_device_terminate_all+0xf4/0x100)
[<c01fdbd0>] (at_xdmac_device_terminate_all) from [<c02221a4>]
(atmel_complete_tx_dma+0x34/0xf4)
[<c02221a4>] (atmel_complete_tx_dma) from [<c01fe4ac>]
(at_xdmac_tasklet+0x14c/0x1ac)
[<c01fe4ac>] (at_xdmac_tasklet) from [<c001de58>]
(tasklet_action+0x68/0xb4)
[<c001de58>] (tasklet_action) from [<c001dfdc>]
(__do_softirq+0xfc/0x238)
[<c001dfdc>] (__do_softirq) from [<c001e140>] (run_ksoftirqd+0x28/0x34)
[<c001e140>] (run_ksoftirqd) from [<c0033a3c>]
(smpboot_thread_fn+0x138/0x18c)
[<c0033a3c>] (smpboot_thread_fn) from [<c0030e7c>] (kthread+0xdc/0xf0)
[<c0030e7c>] (kthread) from [<c000f480>] (ret_from_fork+0x14/0x34)
---[ end trace b57b14a99c1d8812 ]---
It comes from the fact that devices can called some code from the DMA
controller with irq disabled. _bh variant is not intended to be used in
this case since it can enable irqs. Switch to irqsave/irqrestore variant to
avoid this situation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the commit below, I missed the connector allocation in the function
intel_sdvo_analog_init(), leading to those connectors to have a NULL
state pointer.
commit 08d9bc920d
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri Apr 10 10:59:10 2015 +0300
drm/i915: Allocate connector state together with the connectors
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The btusb_read_local_version function has only a single user and with
that just move its functionality in place where it belongs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The __hci_cmd_sync function already handles the command status and
command complete errors. No need to check the status field again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
So, I'm told this problem exists in the world:
> Subject: Build error in -next due to 'efi: Add esrt support'
>
> Building ia64:defconfig ... failed
> --------------
> Error log:
>
> drivers/firmware/efi/esrt.c:28:31: fatal error: asm/early_ioremap.h: No such file or directory
>
I'm not really sure how it's okay that we have things in asm-generic on
some platforms but not others - is having it the same everywhere not the
whole point of asm-generic?
That said, ia64 doesn't have early_ioremap.h . So instead, since it's
difficult to imagine new IA64 machines with UEFI 2.5, just don't build
this code there.
To me this looks like a workaround - doing something like:
generic-y += early_ioremap.h
in arch/ia64/include/asm/Kbuild would appear to be more correct, but
ia64 has its own early_memremap() decl in arch/ia64/include/asm/io.h ,
and it's a macro. So adding the above /and/ requiring that asm/io.h be
included /after/ asm/early_ioremap.h in all cases would fix it, but
that's pretty ugly as well. Since I'm not going to spend the rest of my
life rectifying ia64 headers vs "generic" headers that aren't generic,
it's much simpler to just not build there.
Note that I've only actually tried to build this patch on x86_64, but
esrt.o still gets built there, and that would seem to demonstrate that
the conditional building is working correctly at all the places the code
built before. I no longer have any ia64 machines handy to test that the
exclusion actually works there.
Signed-off-by: Peter Jones <pjones@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
(Compile-)Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
struct timeval uses a 32-bit field for representing seconds, which
will overflow in the year 2038 and beyond. Replace struct timeval with
64-bit ktime_t which is 2038 safe. This is part of a larger effort to
remove instances of 32-bit timekeeping variables (timeval, time_t and
timespec) from the kernel.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
This patch adds native DSD support for the XMOS based JLsounds I2SoverUSB board
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the explicit checking against ss_masks inside a for_each_subsys
block with for_each_subsys_which(..., ss_mask), to take advantage of the
more readable (and more efficient) macro.
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Add a new macro for_each_subsys_which that allows all enabled cgroup
subsystems to be filtered by a bitmask, such that mask & (1 << ssid)
determines if the subsystem is to be processed in the loop body (where
ssid is the unique id of the subsystem).
Also replace the need_forkexit_callback with two separate bitmasks for
each callback to make (ss->{fork,exit}) checks unnecessary.
tj: add a short comment for "if (!CGROUP_SUBSYS_COUNT)".
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes semantic warning for debugging data dump feature.
Previous code is based on the assumption that skb is not null.
New change makes sure that we already have data buffer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After physical reconnect, the rtl8192cu chipset shows low
transmission rates.It cause is that variable "iqk_initialized"
do not de-initialized. So I add this code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Negative adapter->tx_pending is observed while running data traffic,
because tx_pending is decreased once more for AMSDU packet.
since tx_pending have been decreased for all the source MSDU packets,
we don't need to update once more for AMSDU packet.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes issue with the accessing correct ra_list by
downgrading corresponding tid number.
Alternatively, ra lists are created in mwifiex_wmm_add_buf_txqueue
using downgraded tid number.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was missing and would cause issue in WMM handling.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This would enable driver to enter powersave as soon as connected.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We often see ADDBA request packets coming to driver because driver
has registered for action frame subtype. We dont process BA action
frames in host; drop such frames.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Earlier only RSN, WPA and channel switch IEs from tail buffer would
be downloaded to FW.
This patch adds support for downloading more IEs from tail buffer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to parse power constraint IEs from
Tail buffer. This power constraint is then set to FW during
bss_config download.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch extend cfg80211 dump_station handler, support for
dump stations associated to mwifiex micro AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add sta_list firmware command, which can be used
to get power status and rssi for the stations associated to
mwifiex micro AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to disable ongoing CAC in FW upon
detecting radar during CAC period.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes an issue where we were still setting 11h_active
flag to true for channel defs where DFS is not required.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BSS reset would reset all state information in FW.
Issue 11d config command after reset to enabled 11d in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This would enable clearing of FW bss data structures when AP
operations are stopped.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct bss_type assignment in add_virtual_interface.
This would ensure correct operation in multiple station scenarios.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds more detailed information about association failures
- reason and states.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delete jump to a label on the next line, when that label is not
used elsewhere.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier l;
@@
-if (...) goto l;
-l:
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: 6058bb3628 'ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller'
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1433684009.9134.1.camel@ingics.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The SKB returned from the Intel specific version information command is
missing a kfree_skb.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
During the initial setup stage of a controller, the low-level transport
is actually active. This means that HCI_UP is true. To avoid toggling
the transport off and back on again for normal operation the kernel
holds a grace period with HCI_AUTO_OFF that will turn the low-level
transport off in case no user is present.
The idea of the grace period is important to avoid having to initialize
all of the controller twice. So legacy ioctl and the new management
interface knows how to clear this grace period and then start normal
operation.
For the user channel operation this grace period has not been taken into
account which results in the problem that HCI_UP and HCI_AUTO_OFF are
set and the kernel will return EBUSY. However from a system point of
view the controller is ready to be grabbed by either the ioctl, the
management interface or the user channel.
This patch brings the user channel to the same level as the other two
entries for operating a controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
All users of arch/microblaze/include/asm/pci.h get it by including
include/linux/pci.h, which in turn includes <asm/pci.h> after it declares
struct pci_dev.
The forward declaration here is unnecessary, so remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
pci_bus_find_capability() is declared in include/linux/pci.h.
Remove the pci_bus_find_capability() declaration from
arch/microblaze/include/asm/pci.h.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warnings found by sparse:
arch/microblaze/kernel/dma.c:157:5: warning: symbol
'dma_direct_mmap_coherent' was not declared. Should it be static?
arch/microblaze/kernel/kgdb.c:35:14: warning: symbol 'pvr' was not
declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
