The I2S controller can handle sample rates only up to 96000 and the CPU DAI
has already related constraint set so drop the impossible 176400, 192000
switch cases.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of sample rates lower than 44100 currently there is too low MCLK
frequency set for the CODEC. Playback fails with following errors:
$ speaker-test -c2 -t sine -f 1500 -l2 -r 32000
Sine wave rate is 1500.0000Hz
Rate set to 32000Hz (requested 32000Hz)
Buffer size range from 128 to 131072
Period size range from 64 to 65536
Using max buffer size 131072
Periods = 4
Unable to set hw params for playback: Invalid argument
Setting of hwparams failed: Invalid argument
[ 497.883700] max98090 1-0010: Invalid master clock frequency
To fix this the I2S root clock's frequency is increased, depending
on sampling rate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds some device nodes for the PCIe function block and updates
related pinmux.
Moreover, we add interrupt-map properties in both parent and children as
the chip only has one IRQ per slot that is connected to all INTx and get
propagated through the bridges and it also represents the root ports own
interrupts.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
1. split MFG power domain into MFG/MFG_SC1/MFG_SC2/MFG_SC3
according to MT2712 ECO design change
2. add subdomain support for MT2712
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add new power domains(MFG_SC1/MFG_SC2/MFG_SC3)
for MT2712 according to ECO design change.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a device-tree binding for Texas Instrument's PCM1789 codec.
For the moment, only I2C bus is supported but SPI could be added
in future.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Texas Instruments's PCM1789 DAC support.
It is a simple DAC and does not have many registers.
One particularity about this DAC is that the clocks must be
always enabled. Also, an entire software reset is necessary
while starting to play a sound otherwise, the clocks are not
synchronized (so the DAC is not able to send data).
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document support for the sound modules in the Renesas M3-W (r8a7796)
SoC.
No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the remove callback is removed, the snd_soc_unregister_component()
is missing when remove device. Using devm_snd_soc_register_component()
instead of snd_soc_register_component().
Fixes: d06f33aed8 ("ASoC: da7210: replace codec to component")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Compatible for XU4 audio is not being used. Instead the board uses the
same compatible as XU3. The devices are now just compatible so they
should use the same value. Mark "hardkernel,odroid-xu4-audio" as being
deprecated so in this future could be removed to limit useless
properties.
Additionally add older compatibles appearing in the bindings.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the remove callback is removed, the snd_soc_unregister_component()
is missing when remove device. Using devm_snd_soc_register_component()
instead of snd_soc_register_component().
Fixes: 10dc44c646 ("ASoC: wm8400: replace codec to component")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's not necessary to unregister a component registered
with devm_snd_soc_register_component().
Fixes: f1b5bf0736 ("ASoC: mt2701/mt8173: replace platform to componen")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds syscon property for specifying soc-glue core.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state. After
resetting of SoC Hi-Z state is selected. This driver set to signal
output state when syscon property is available.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds syscon property for specifying soc-glue core into
DT binding documentation.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state. If you don't
need to use features on soc-glue described above you can ommit this
property.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does not disable ref_clk on remove.
According to the comment, the only reason to enable the clock is to get
its rate. So, it should be safe to disable clk just after that.
By the way, clk_prepare_enable() looks to be more appropriate
than clk_enable() here.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using BIT() makes (1 << foo) constructions easier to read, and
also account for common mistakes where bit 31 is not working
because of numbers being interpreted as negative unless
specified as unsigned.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is a pure GPIO driver and should only include
<linux/gpio/driver.h>. Refrain from using GPIOF_* flags in
the driver, just use 1/0 to return direction.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is a pure GPIO driver and should only include
<linux/gpio/driver.h>. Drop the include of <linux/gpio.h>
from the platform data header as well, it serves no purpose.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Emma Mobile (EM) GPIO driver uses the too generic include
<linux/gpio.h>. It is a driver so it should just use
<linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver has no business including <linux/gpio.h>, it is a
driver so include <linux/gpio/driver.h>.
GPIOF_DIR_IN/GPIOF_DIR_OUT are for consumers and should not be
used in drivers to use just 1/0 instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The #sound-dai-cells DT property is required to describe link between
the HDMI IP block and the SoC's audio subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This adds code to the radix hypervisor page fault handler to handle the
case where the guest memory is backed by 1GB hugepages, and put them
into the partition-scoped radix tree at the PUD level. The code is
essentially analogous to the code for 2MB pages. This also rearranges
kvmppc_create_pte() to make it easier to follow.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When using the radix MMU, we can get hypervisor page fault interrupts
with the DSISR_SET_RC bit set in DSISR/HSRR1, indicating that an
attempt to set the R (reference) or C (change) bit in a PTE atomically
failed. Previously we would find the corresponding Linux PTE and
check the permission and dirty bits there, but this is not really
necessary since we only need to do what the hardware was trying to
do, namely set R or C atomically. This removes the code that reads
the Linux PTE and just update the partition-scoped PTE, having first
checked that it is still present, and if the access is a write, that
the PTE still has write permission.
Furthermore, we now check whether any other relevant bits are set
in DSISR, and if there are, then we proceed with the rest of the
function in order to handle whatever condition they represent,
instead of returning to the guest as we did previously.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This improves the handling of transparent huge pages in the radix
hypervisor page fault handler. Previously, if a small page is faulted
in to a 2MB region of guest physical space, that means that there is
a page table pointer at the PMD level, which could never be replaced
by a leaf (2MB) PMD entry. This adds the code to clear the PMD,
invlidate the page walk cache and free the page table page in this
situation, so that the leaf PMD entry can be created.
This also adds code to check whether a PMD or PTE being inserted is
the same as is already there (because of a race with another CPU that
faulted on the same page) and if so, we don't replace the existing
entry, meaning that we don't invalidate the PTE or PMD and do a TLB
invalidation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since commit fb1522e099 ("KVM: update to new mmu_notifier semantic
v2", 2017-08-31), the MMU notifier code in KVM no longer calls the
kvm_unmap_hva callback. This removes the PPC implementations of
kvm_unmap_hva().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from powernv driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
RAPL MSRs and handling for Cannon Lake are similar to Sky Lake
and Kaby Lake.
Signed-off-by: Joe Konno <joe.konno@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a device referred to by ACPI LPI constrains (coming from function 1
of the Low Power S0 Idle _DSM interface) is not power-manageable via
ACPI (no _PS0 method and no power resources), the code generating
diagnostic information for the LPI constraints will print a message
about that to the kernel log on every system suspend-resume cycle
(possibly for multiple times).
That is not very useful and noisy, so modify that code to disregard
the LPI list entries corresponding to the devices that are not power-
manageable after printing that information for them once.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fix grammar and punctuation (end sentences with a period) in the
Kconfig help text for ACPI_PROCFS_POWER.
I was looking at this since it appears to be going away (again,
some day) and I have a working script that uses this info to tell me
battery usage. I can update the script to use /sys/class/power_supply
(in theory) but the contents (with units) should be documented in
Documentation/ABI/ before /proc/acpi/battery/ is removed (IMO).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can return directly at the beginning of the function and save the 'err'
label.
We can also explicitly return 0 when the probe succeed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Avoid some code ducplication and be more future-proof.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A number of Dell systems require an OEM _OSI string "Linux-Dell-Video"
as a BIOS workaround to disable RTD3 which causes systems hangs when
NVidia graphics cards are installed. The affected Dell systems are
with system IDs: 0818, 0819, 0820, 0850, 0851, 086F, 0870, 0885 and
0886.
The form of the OEM _OSI strings is defined by each OEMs and is
discussed in Documentation/acpi/osi.txt.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The H3 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
It should be good that no use "_" is in DT node name. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The property pinctrl-names is totally superfluous. It would be good to
remove the property to keep the node neatness. There is actually
unnecessary to set up any pins for data path TRGMII between main SoC and
MT7530. Furthermore, it's more reasonable for the pin setup of control
path MDIO bus is being placed inside the node of ethernet controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On bpi-r2 board, totally there're four UARTs which we usually called
uart[0-3] helpful to extend slow-I/O devices. Among those ones, uart2 has
dedicated pin slot which is used to console log. uart[0-1] appear at the
40-pins connector and uart3 has no pinout, but just has test points (TP47
for TX and TP48 for RX, respectively) nearby uart2, but we don't enable
uart3 in the patch. The missing pinctrl is also being supplemented for
those newly added devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Both mmc devices on bananapi-r2 board should all use the fixed regulators
as their power source instead of PMIC MT6323 exports.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>