VMD domains are allocated starting at 0x10000, not 0x1000 as the comment
said. Correct the comment and add a reference to the ACPI spec for _SEG.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Use a local "struct device *dev" for brevity and consistency with other
drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI host bridge found on Tegra SoCs doesn't require the MSI target
address to be backed by physical system memory. Writes are intercepted
within the controller and never make it to the memory pointed to.
Since no actual system memory is required, remove the allocation of a
single page and hardcode the MSI target address with a special address that
maps to the last 4 KiB page within the range that is reserved for system
memory and memory-mapped I/O in the FPCI address map.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
The MSI target address can reside beyond the 32-bit boundary on devices
with more than 2 GiB of system memory. The PCI host bridge on Tegra can
easily support 64-bit addresses, so make sure to pass the upper 32 bits of
the target address to endpoints when allocating MSI entries.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
We have a local "struct device *dev" in rockchip_pcie_probe(). Use it
consistently throughout the function. No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Wenrui Li changed his employer and is no longer able to maintain the
Rockchip PCIe driver, so remove his email address from this file.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The default value of MPS for RC is 128 bytes, but actually it could support
256 bytes. So this patch fixes this issue.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe base specification (Revision 3.1a), section 7.5.3, type 1
configuration space header should be used when accessing PCIe switch. So
we need to reconfigure the header according to the bus number we are
accessing. Otherwise we could not visit the buses behind the switch.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need to reconfigure the header type later, so split out a new function.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configuration accesses is also part of ATU settings, so let's keep all of
them inside rockchip_pcie_cfg_atu().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename rockchip_cfg_atu() to keep the name consistent with other functions
in pcie-rockchip.c.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
vpcie0v9 is used for PHY, so we could disable it as we don't need PHY to
work then in S3 if folks assign it DT. But we should note that there is a
side effect that we could not support beacon wakeup if we disable vpcie0v9
for aggressive power-saving.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
of_device_ids are not supposed to change at runtime. All functions working
with of_device_ids provided by <linux/of.h> work with const of_device_ids.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive
text.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Limit TLP size to 2K to work around a hardware bug in the v0 version of
PCIe IP. When using default TLP size of 4K, the internal buffer gets
corrupted due to this hardware bug.
This bug was originally noticed during ssh session between APQ8064-based
board and PC. Network packets got corrupted randomly and terminated the ssh
session due to this bug.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Trivial fix to spelling mistake in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously the v0, v1, and v2 functions were not grouped together in a
consistent order. Reorder them to make them consistent.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the IPQ4019 PCIe controller. IPQ4019 supports Gen 1/2, one
lane, one PCIe root complex with support for MSI and legacy interrupts, and
it conforms to PCI Express Base 2.1 specification.
The core init is the same as for the MSM8996, however the clocks and reset
lines differ.
[bhelgaas: fix qcom_pcie_get_resources_v3(), qcom_pcie_init_v3() compile
issues]
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acked-by: Rob Herring <robh@kernel.org> # binding
Hisilicon PCIe driver shares the common functions for PCIe dw-host.
The poweron functions are developed on hi3660 SoC, while other functions
are common for Kirin series SoCs.
Low power mode (L1 sub-state and Suspend/Resume), hotplug and MSI feature
are not supported currently.
Signed-off-by: Xiaowei Song <songxiaowei@hisilicon.com>
[bhelgaas: fold in MAINTAINERS update from
http://lkml.kernel.org/r/20170704021516.96575-1-songxiaowei@hisilicon.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Some boards might require to control a regulator to power the PCIe port.
Add support for an optional regulator defined in Device Tree linked in the
PCIe controller under `vpcie-supply`. If present, the regulator will be
disabled and then enabled as part of the PCIe host initialization process
and will be disabled when shutting down.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
[bhelgaas: use dev_err() instead of pr_err() in
imx6_pcie_assert_core_reset()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Update the Hyper-V vPCI driver to use the Server-2016 version of the vPCI
protocol, fixing MSI creation and retargeting issues.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Hyper-V vPCI offers different protocol versions. Add the infra for
negotiating the one to use.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
To ease parallel effort to centralize CPU-number-to-vCPU-number conversion,
temporarily stand up own version, file-local hv_tmp_cpu_nr_to_vp_nr().
Once the changes have merged, this work-around can be removed, and the
calls replaced with hv_cpu_number_to_vp_number().
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
The hv_pcibus_device structure contains an in-memory hypercall argument
that must not cross a page boundary. Allocate the structure as a page to
ensure that.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Fix comment formatting and use proper integer fields.
Signed-off-by: Jork Loeser <jloeser@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
The Faraday FTPCI100 controller has two clock ports, PCLK and PCICLK. Add
bindings for these two clocks so we can assign them in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Previously, we tried to clear interrupt requests by clearing bits in the
PCIECTRL_DRA7XX_CONF_IRQSTATUS_MSI and PCIECTRL_DRA7XX_CONF_IRQSTATUS_MAIN
registers. But per the TRM, these fields are RW1C, so we must *set* bits
to clear the interrupt bits.
Fixes: 47ff3de911 ("PCI: dra7xx: Add TI DRA7xx PCIe driver")
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The PCI controller attached to a SoC isn't much use if the core SoC isn't
enabled, unless of course it's compile testing, so add appropriate
dependency.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The dw_pcie_host_ops structures are never modified. Constify these
structures such that these can be write-protected.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Similar as commit 8ff0ef996c ("PCI: host: Mark PCIe/PCI (MSI) IRQ cascade
handlers as IRQF_NO_THREAD"), we should mark PCIe/PCI (MSI) IRQ cascade
handlers in designware, qcom, and vmd as IRQF_NO_THREAD explicitly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com> # vmd
Acked-by: Jingoo Han <jingoohan1@gmail.com> # pcie-designware-plat.c
Original comments is confusing on "OBJ directory", make it clear.
Bonus: move comments close to what it wants to comment.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
kbuild runs "find" on each entry in CONFIG_INITRAMFS_SOURCE that is a
directory. The order of the file listing output by "find" matter for
build reproducability, hence this patch applies "sort" to get
deterministic results.
Without this patch, two different machines with identical initramfs
directory input may produce differing initramfs cpio archives (different
hash) due to the different order of the files within the archive.
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixed build error due to misplaced "#ifdef CONFIG_INET" (moved 1
statement up).
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of struct pci_host_bridge.map_irq pointer it is
possible to assign IRQs for all devices originating from a PCI host bridge
at probe time; this is implemented through pci_assign_irq() that relies on
the struct pci_host_bridge.map_irq pointer to map IRQ for a given device.
The benefits this brings are twofold:
- the IRQ for a device is assigned once at probe time
- the IRQ assignment works also for hotplugged devices
With all DT based PCI host bridges converted to the struct
pci_host_bridge.{map/swizzle}_irq hooks mechanism the DT IRQ allocation in
ARM64 pcibios_alloc_irq() is now redundant and can be removed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the xilinx-nwl PCI host driver to move the
IRQ allocation into core code and stop relying on arch-specific callbacks.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the rockchip PCI host driver to move the IRQ
allocation into core code and stop relying on arch-specific callbacks.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wenrui Li <wenrui.li@rock-chips.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ
mapping can be done automatically by PCI core code through the
pci_assign_irq() function instead of resorting to arch-specific
implementation callbacks to carry out the same task which force PCI host
bridge drivers implementation to implement per-arch kludges to carry out a
task that is inherently architecture agnostic.
Add map/swizzle IRQs hooks to the xgene PCI host driver to move the IRQ
allocation into core code and stop relying on arch-specific callbacks.
Tested-by: Khuong Dinh <kdinh@apm.com> # with e1000e
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI altera host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ley Foon Tan <lftan@altera.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI versatile host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: folded in typo fix from Arnd Bergmann <arnd@arndb.de>:
http://lkml.kernel.org/r/20170621215323.3921382-4-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh@kernel.org>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI host-common bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI ftpci100 host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI designware host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI iproc host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Jon Mason <jonmason@broadcom.com>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI rcar host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Simon Horman <horms@verge.net.au>
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now
allocated in the pci_assign_irq() callback automatically, PCI host bridge
drivers can stop relying on pci_fixup_irqs() for IRQ allocation.
Drop pci_fixup_irqs() usage from PCI xilinx host bridge driver.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
