fsl,tmu-calibration contains cell pairs (u32-matrix). Mark them as such.
Use matching property syntax and allow correct validation.
No functional changes.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node names should be generic.
Use 'rtc' for the rtc node to fix the following dt-schema warning:
imx27-phytec-phycore-rdk.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per imx-keypad.yaml, '#address-cells', '#size-cells', 'clock-names'
are not valid properties.
Remove them to fix the following dt-schema warning:
imx25-pdk.dtb: kpp@43fa8000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'clock-names' were unexpected)
from schema $id: http://devicetree.org/schemas/input/imx-keypad.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Defining the size of register regions is not really in scope of what
bindings need to cover. The schema for this is also not completely correct
as a reg entry can be variable number of cells for the address and size,
but the schema assumes 1 cell.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231213232455.2248056-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Even if the 'dsp' node is disabled the memory intended to be used by the
DSP is reserved. This limits the memory range suitable for CMA allocation.
Thus disable the dsp_reserved node. DSP users need to enable it in parallel
to the 'dsp' node.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8qxp re-uses imx8qm VPU subsystem file, but it has different base
addresses. Also imx8qxp has only two VPU cores, delete vpu_vore2 and
mu2_m0 accordingly.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per nxp,ptn5110.yaml, 'port' should be placed under 'connector'.
Do as requested to fix the following dt-schema warning:
imx8qxp-mek.dtb: tcpc@50: connector:ports: 'port@0' is a required property
from schema $id: http://devicetree.org/schemas/usb/nxp,ptn5110.yaml#
imx8qxp-mek.dtb: tcpc@50: connector: Unevaluated properties are not allowed ('ports' was unexpected)
from schema $id: http://devicetree.org/schemas/usb/nxp,ptn5110.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the display and nodes required for its operation.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/c3a51791d54deaa818b8526975fc4e16ef1090ce.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/06612aff79dfb52d5b0b20129dff5e4b1f04d3a7.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
In the error path emit an error message replacing the (less useful)
message by the core. Apart from the improved error message there is no
change in behaviour.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Link: https://lore.kernel.org/linux-pci/50de44ea8931465fd9cdc821854ea761cb43adf6.1701682617.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Pengfei Xu reported [1] Syzkaller/KASAN issue found in bpf_link_show_fdinfo.
The reason is missing BPF_LINK_TYPE invocation for uprobe multi
link and for several other links, adding that.
[1] https://lore.kernel.org/bpf/ZXptoKRSLspnk2ie@xpf.sh.intel.com/
Fixes: 89ae89f53d ("bpf: Add multi uprobe link")
Fixes: e420bed025 ("bpf: Add fd-based tcx multi-prog infra with link support")
Fixes: 84601d6ee6 ("bpf: add bpf_link support for BPF_NETFILTER programs")
Fixes: 35dfaad718 ("netkit, bpf: Add bpf programmable net device")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Acked-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/bpf/20231215230502.2769743-1-jolsa@kernel.org
Temporarily disable dummy_struct_ops test on s390.
The breakage is likely due to
commit 2cd3e3772e ("x86/cfi,bpf: Fix bpf_struct_ops CFI").
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Peter Zijlstra says:
====================
x86/cfi,bpf: Fix CFI vs eBPF
Hi!
What started with the simple observation that bpf_dispatcher_*_func() was
broken for calling CFI functions with a __nocfi calling context for FineIBT
ended up with a complete BPF wide CFI fixup.
With these changes on the BPF selftest suite passes without crashing -- there's
still a few failures, but Alexei has graciously offered to look into those.
(Alexei, I have presumed your SoB on the very last patch, please update
as you see fit)
Changes since v2 are numerous but include:
- cfi_get_offset() -- as a means to communicate the offset (ast)
- 5 new patches fixing various BPF internals to be CFI clean
Note: it *might* be possible to merge the
bpf_bpf_tcp_ca.c:unsupported_ops[] thing into the CFI stubs, as is
get_info will have a NULL stub, unlike the others.
---
arch/riscv/include/asm/cfi.h | 3 +-
arch/riscv/kernel/cfi.c | 2 +-
arch/x86/include/asm/cfi.h | 126 +++++++++++++++++++++++++++++++++++++-
arch/x86/kernel/alternative.c | 87 +++++++++++++++++++++++---
arch/x86/kernel/cfi.c | 4 +-
arch/x86/net/bpf_jit_comp.c | 134 +++++++++++++++++++++++++++++++++++------
include/asm-generic/Kbuild | 1 +
include/linux/bpf.h | 27 ++++++++-
include/linux/cfi.h | 12 ++++
kernel/bpf/bpf_struct_ops.c | 16 ++---
kernel/bpf/core.c | 25 ++++++++
kernel/bpf/cpumask.c | 8 ++-
kernel/bpf/helpers.c | 18 +++++-
net/bpf/bpf_dummy_struct_ops.c | 31 +++++++++-
net/bpf/test_run.c | 15 ++++-
net/ipv4/bpf_tcp_ca.c | 69 +++++++++++++++++++++
16 files changed, 528 insertions(+), 50 deletions(-)
====================
Link: https://lore.kernel.org/r/20231215091216.135791411@infradead.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Ensure the various dtor functions match their prototype and retain
their CFI signatures, since they don't have their address taken, they
are prone to not getting CFI, making them impossible to call
indirectly.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231215092707.799451071@infradead.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a CFI_NOSEAL() helper to mark functions that need to retain their
CFI information, despite not otherwise leaking their address.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231215092707.669401084@infradead.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
BPF struct_ops uses __arch_prepare_bpf_trampoline() to write
trampolines for indirect function calls. These tramplines much have
matching CFI.
In order to obtain the correct CFI hash for the various methods, add a
matching structure that contains stub functions, the compiler will
generate correct CFI which we can pilfer for the trampolines.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231215092707.566977112@infradead.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Where the main BPF program is expected to match bpf_func_t,
sub-programs are expected to match bpf_callback_t.
This fixes things like:
tools/testing/selftests/bpf/progs/bloom_filter_bench.c:
bpf_for_each_map_elem(&array_map, bloom_callback, &data, 0);
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231215092707.451956710@infradead.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The current BPF call convention is __nocfi, except when it calls !JIT things,
then it calls regular C functions.
It so happens that with FineIBT the __nocfi and C calling conventions are
incompatible. Specifically __nocfi will call at func+0, while FineIBT will have
endbr-poison there, which is not a valid indirect target. Causing #CP.
Notably this only triggers on IBT enabled hardware, which is probably why this
hasn't been reported (also, most people will have JIT on anyway).
Implement proper CFI prologues for the BPF JIT codegen and drop __nocfi for
x86.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231215092707.345270396@infradead.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Normal include order is that linux/foo.h should include asm/foo.h, CFI has it
the wrong way around.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20231215092707.231038174@infradead.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive PCI
drivers to use the newer symbol.
Link: https://lore.kernel.org/linux-pci/20230918-safeness-cornflake-62278bc3aaaa@wendy
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Document the PCIe Controller on the SM8650 platform by using the
SM8550 bindings as a fallback.
Link: https://lore.kernel.org/linux-pci/20231128-topic-sm8650-upstream-bindings-pcie-v2-1-b72e2d13bcf1@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
On some boards the 100MHz PCIe reference clock to both controller and
devices is controllable. Add that clock to the list of clocks.
The clock is optional, so the minItems stays the same.
Link: https://lore.kernel.org/linux-pci/20231206145041.667900-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
There is no "resets-names" property, but "reset-names".
Fixes: 075a9d5593 ("dt-bindings: PCI: qcom: Convert to YAML")
Link: https://lore.kernel.org/linux-pci/20231111142006.51883-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
PCI node in Qualcomm SM8150 should have exactly 8 clocks, including the
ref clock.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20231208105155.36097-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
PCI node in Qualcomm SC8180x DTS has 8 clocks:
sc8180x-primus.dtb: pci@1c00000: 'oneOf' conditional failed, one must be fixed:
['pipe', 'aux', 'cfg', 'bus_master', 'bus_slave', 'slave_q2a', 'ref', 'tbu'] is too short
Link: https://lore.kernel.org/linux-pci/20231208105155.36097-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
The PCIe controller on SDX55 has five entries in its iommu-map, MSM8998
has one and SDM845 has sixteen, so allow wider number of items to fix
dtbs_check warnings like:
qcom-sdx55-mtp.dtb: pcie@1c00000: iommu-map: [[0, 21, 512, 1], [256, 21, 513, 1],
[512, 21, 514, 1], [768, 21, 515, 1], [1024, 21, 516, 1]] is too long
Link: https://lore.kernel.org/linux-pci/20231208105155.36097-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Log bridge secondary/subordinate bus and window information at the same
time we log the bridge BARs, just after discovering the bridge and before
scanning the bridge's secondary bus. This logs the bridge and downstream
devices in a more logical order:
- pci 0000:00:01.0: [8086:1901] type 01 class 0x060400
- pci 0000:01:00.0: [10de:13b6] type 00 class 0x030200
- pci 0000:01:00.0: reg 0x10: [mem 0xec000000-0xecffffff]
- pci 0000:00:01.0: PCI bridge to [bus 01]
- pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
+ pci 0000:00:01.0: [8086:1901] type 01 class 0x060400
+ pci 0000:00:01.0: PCI bridge to [bus 01]
+ pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
+ pci 0000:01:00.0: [10de:13b6] type 00 class 0x030200
+ pci 0000:01:00.0: reg 0x10: [mem 0xec000000-0xecffffff]
Note that we read the windows into a temporary struct resource that is
thrown away, not into the resources in the struct pci_bus.
The windows may be adjusted after we know what downstream devices require,
and those adjustments are logged as they are made.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously pci_read_bridge_io(), pci_read_bridge_mmio(), and
pci_read_bridge_mmio_pref() unconditionally logged the bridge window
resource. A future change will call these functions earlier and more
often. Add a "log" parameter so callers can control whether to generate
the log message. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we logged information about devices *below* the bridge before
logging information about the bridge itself, e.g.,
pci 0000:00:01.0: [8086:1901] type 01 class 0x060400
pci 0000:01:00.0: [10de:13b6] type 00 class 0x030200
pci 0000:01:00.0: reg 0x10: [mem 0xec000000-0xecffffff]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
This is partly because the bridge windows are read in this path:
pci_scan_child_bus_extend
for (devfn = 0; devfn < 256; devfn += 8)
pci_scan_slot(bus, devfn) # scan below bridge
pcibios_fixup_bus(bus)
pci_read_bridge_bases(bus) # read bridge windows
pci_read_bridge_io(bus)
Remove the assumption that the secondary (child) pci_bus already exists by
passing in the bridge device (instead of the pci_bus) and a resource
pointer when reading bridge windows. A future change can use this to log
the bridge details before we enumerate the devices below the bridge.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_read_bridge_windows() below the functions that read the I/O,
memory, and prefetchable memory windows, so pci_read_bridge_windows() can
use them in the future. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the pci_resource_name() to get the name of the resource and use it
while printing log messages.
[bhelgaas: rename to match struct resource * names, also use names in other
BAR messages]
Link: https://lore.kernel.org/r/20211106112606.192563-3-puranjay12@gmail.com
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI log messages print the register offsets at some places and BAR
numbers at other places. There is no uniformity in this logging mechanism.
It would be better to print names than register offsets.
Add a helper function that aids in printing more meaningful information
about the BAR numbers like "VF BAR", "ROM", "bridge window", etc. This
function can be called while printing PCI log messages.
[bhelgaas: fold in Lukas' static array suggestion from
https://lore.kernel.org/all/20211106115831.GA7452@wunner.de/]
Link: https://lore.kernel.org/r/20211106112606.192563-2-puranjay12@gmail.com
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Log the device type when enumeration a device. Sample output changes:
- pci 0000:00:00.0: [8086:1237] type 00 class 0x060000
+ pci 0000:00:00.0: [8086:1237] type 00 class 0x060000 conventional PCI endpoint
- pci 0000:00:1c.0: [8086:a110] type 01 class 0x060400
+ pci 0000:00:1c.0: [8086:a110] type 01 class 0x060400 PCIe Root Port
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After commit 1e50915fe0 ("raid: improve MD/raid10 handling of correctable
read errors."), rdev will be set to faulty if it reads data error to many
times in raid10. Add this mechanism to raid1 now.
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20231215023852.3478228-3-linan666@huaweicloud.com
Move check_decay_read_errors() to raid1-10.c and factor out a helper
exceed_read_errors() to check if read_errors exceeds the limit, so that
raid1 can also use it. There are no functional changes.
Signed-off-by: Li Nan <linan122@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20231215023852.3478228-2-linan666@huaweicloud.com
Upon assembling the array, both kernel and mdadm allow the devices to have event
counter difference of 1, and still consider them as up-to-date.
However, a device whose event count is behind by 1, may in fact not be up-to-date,
and array resync with such a device may cause data corruption.
To avoid this, consult the superblock of the freshest device about the status
of a device, whose event counter is behind by 1.
Signed-off-by: Alex Lyakas <alex.lyakas@zadara.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/1702470271-16073-1-git-send-email-alex.lyakas@zadara.com
Should check return value of f2fs_recover_xattr_data in
__f2fs_setxattr rather than doing invalid retry if error happen.
Also just do set_page_dirty in f2fs_recover_xattr_data when
page is changed really.
Fixes: 50a472bbc7 ("f2fs: do not return EFSCORRUPTED, but try to run online repair")
Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Our btrfs subvolume snapshot <source> <destination> utility enforces
that <source> is the root of the subvolume, however this isn't enforced
in the kernel. Update the kernel to also enforce this limitation to
avoid problems with other users of this ioctl that don't have the
appropriate checks in place.
Reported-by: Martin Michaelis <code@mgjm.de>
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This code is rarely (never?) enabled by distros, and it hasn't caught
anything in decades. Let's kill off this legacy debug code.
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are multiple ways to grab references to credentials, and the only
protection we have against overflowing it is the memory required to do
so.
With memory sizes only moving in one direction, let's bump the reference
count to 64-bit and move it outside the realm of feasibly overflowing.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of passing three individual members of 'struct btrfs_io_geometry'
into btrfs_max_io_len(), pass a pointer to btrfs_io_geometry.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of passing three members of 'struct btrfs_io_geometry' into
set_io_stripe() pass a pointer to the whole structure and then get the needed
members out of btrfs_io_geometry.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Open code set_io_stripe() for RAID56, as it
a) uses a different method to calculate the stripe_index
b) doesn't need to go through raid-stripe-tree mapping code.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that all the per-profile if/else statement blocks have been
converted to calls to helper the conversion to switch/case is
straightforward.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we have a container for the I/O geometry that has all the needed
information for the block mappings of SINGLE profiles, factor out a helper
calculating this information.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Now that we have a container for the I/O geometry that has all the needed
information for the block mappings of RAID5 and RAID6, factor out a helper
calculating this information.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Reduce the scope of 'data_stripes' in btrfs_map_block(). While the
change alone may not make too much sense, it helps us factoring out a
helper function for the block mapping of RAID56 I/O.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>