Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240410170317.248715-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Allow 'power-domains' property because i.MX8DXL i.MX8QM and i.MX8QXP need
it. EDMA supports each power-domain for each dma channel. So minItems and
maxItems align 'dma-channels'.
Change fsl,imx93-edma3 example to fsl,imx8qm-edma to reflect this variants.
Fixed below DTB_CHECK warning:
dma-controller@599f0000: Unevaluated properties are not allowed ('power-domains' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240417152457.361340-2-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
fsl,imx8qm-adma and fsl,imx8qm-edma don't require 'clocks'. Remove it from
required and add 'if' block for other compatible string to keep the same
restrictions.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240417152457.361340-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix all kernel-doc warnings under drivers/dma/fsl-dpaa2-qdma.
./scripts/kernel-doc -v -none drivers/dma/fsl-dpaa2-qdma/*
drivers/dma/fsl-dpaa2-qdma/dpdmai.c:262: warning: Function parameter or struct member 'queue_idx' not described in 'dpdmai_set_rx_queue'
drivers/dma/fsl-dpaa2-qdma/dpdmai.c:339: warning: Excess function parameter 'fqid' description in 'dpdmai_get_tx_queue'
...
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202404190019.t4IhmbHh-lkp@intel.com/
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240418185851.3221726-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New sdma script (sdma-6q: v3.6, sdma-7d: v4.6) support i2c at imx8mp and
imx6ull. So add I2C dma support.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Acked-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240419150729.1071904-3-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The macros SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V<n> actually related with the
struct sdma_script_start_addrs.
struct sdma_script_start_addrs {
...
/* End of v1 array */
...
/* End of v2 array */
...
/* End of v3 array */
...
/* End of v4 array */
};
When add new field of sdma_script_start_addrs, it is easy to miss update
SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V<n>.
Employ offsetof for SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V<n> macros instead of
hardcoding numbers. the preprocessing stage will calculate the size for
each version automatically.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240419150729.1071904-2-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add peripheral types ID 27 for I2C because sdma firmware (sdma-6q: v3.6,
sdma-7d: v4.6) support I2C DMA transfer.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240419150729.1071904-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Fixes: 3d83d4d490 ("coresight: tpiu: Move ACPI support from AMBA driver to platform driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/ad5e0d3ec081444a5ad04a7be277dde3afcb696b.1713858615.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Fixes: 70750e257a ("coresight: tmc: Move ACPI support from AMBA driver to platform driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/3cf26d85a8d45f0efb07e07f3307a1b435ebf61e.1713858615.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Fixes: 057256aaac ("coresight: stm: Move ACPI support from AMBA driver to platform driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/3fefa60744fc68c9c4b40aeb69e34cda22582c4b.1713858615.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Fixes: 965edae4e6 ("coresight: debug: Move ACPI support from AMBA driver to platform driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/fb3d7db82a2490ace41c51b16ad17ef61549e2f6.1713858615.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Fixes: 2356732385 ("coresight: catu: Move ACPI support from AMBA driver to platform driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/16a7123efa7d97ae62a02ccbf9b39d146b066860.1713858615.git.u.kleine-koenig@pengutronix.de
The eDMA hardware issue only exist imx8QM A0. A0 never mass production.
The compatible string "fsl,imx8qm-adma" is unused. So remove it safely.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240424064508.1886764-3-joy.zou@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The eDMA hardware issue only exist imx8QM A0. A0 never mass production.
So remove the workaround safely.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240424064508.1886764-2-joy.zou@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The QCom hidma binding was used on a defunct QCom server platform which
mainly used ACPI. DT support in the Linux driver has been broken since
2018, so it seems this binding is unused and can be dropped.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240423161413.481670-2-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT support in hidma has been broken since commit 37fa4905d2
("dmaengine: qcom_hidma: simplify DT resource parsing") in 2018. The
issue is the of_address_to_resource() calls bail out on success rather
than failure. This driver is for a defunct QCom server platform where
DT use was limited to start with. As it seems no one has noticed the
breakage, just remove the DT support altogether.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240423161413.481670-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In "struct div4_clk", the "flags" field is unused.
Remove it, and update the "div4_clks" array accordingly.
Found with cppcheck, unusedStructMember.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/658e6b1b23d5b66646bb830361b8c55ccf797771.1713025170.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/G3S SoC supports configurable supply voltages for several of its
I/O interfaces. All of these interfaces support both 1.8V and 3.3V
supplies, but only the Ethernet and XSPI interfaces support a 2.5V
supply.
Voltage selection for the XSPI interface is not yet supported, so this
leaves only the Ethernet interfaces currently supporting selection of a
2.5V supply. So we need to return an error if there is an attempt to
select a 2.5V supply for any non-Ethernet interface.
Fixes: 51996952b8 ("pinctrl: renesas: rzg2l: Add support to select power source for Ethernet pins")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240417114132.6605-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pass the dev_priv parameter to the low-level helpers, and move the
implicit dev_priv usage one level higher.
sed -i "s/\(_MMIO_PIPE2(\|_MMIO_TRANS2(\|_MMIO_CURSOR2(\)/\1dev_priv, /" \
$(git ls-files drivers/gpu/drm/i915)
Name the parameter "display", as the generics allow it to be display
already.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3a865664898586ff6cb8e74eab3d1f36eafc0557.1713890614.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Most users of _MMIO_PIPE3() and _MMIO_PORT3() need to add the MMIO base
to the registers. Convert the macros to _MMIO_BASE_PIPE3() and
_MMIO_BASE_PORT3() to move the base addition until after the register
selection. If the register address depends on DISPLAY_MMIO_BASE(), this
removes the need to figure the base out for each register, and it only
needs to be added once.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4b95f125f5021abc00b5fc661b2728f1b583c01e.1713890614.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Philo Lu says:
====================
tcp: update TCPCB_EVER_RETRANS after trace_tcp_retransmit_skb()
Move TCPCB_EVER_RETRANS updating after the trace_tcp_retransmit_skb()
in __tcp_retransmit_skb(), and then we are aware of whether the skb has
ever been retransmitted in this tracepoint. This can be used, e.g., to get
retransmission efficiency by counting skbs w/ and w/o TCPCB_EVER_RETRANS
(through bpf tracing programs).
For this purpose, TCPCB_EVER_RETRANS is also needed to be exposed to bpf.
Previously, the flags are defined as macros in struct tcp_skb_cb. I moved them
out into a new enum, and then they can be accessed with vmlinux.h.
We have discussed to achieve this with BPF_SOCK_OPS in [0], and using
tracepoint is thought to be a better solution.
[0]
https://lore.kernel.org/all/20240417124622.35333-1-lulie@linux.alibaba.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marking TCP_SKB_CB(skb)->sacked with TCPCB_EVER_RETRANS after the
traceopint (trace_tcp_retransmit_skb), then we can get the
retransmission efficiency by counting skbs w/ and w/o TCPCB_EVER_RETRANS
mark in this tracepoint.
We have discussed to achieve this with BPF_SOCK_OPS in [0], and using
tracepoint is thought to be a better solution.
[0]
https://lore.kernel.org/all/20240417124622.35333-1-lulie@linux.alibaba.com/
Signed-off-by: Philo Lu <lulie@linux.alibaba.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the flag definitions for tcp_skb_cb->sacked into a new enum named
tcp_skb_cb_sacked_flags, then we can get access to them in bpf via
vmlinux.h, e.g., in tracepoints.
This patch does not change any existing functionality.
Signed-off-by: Philo Lu <lulie@linux.alibaba.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dt-schema documentation and clock IDs for the high speed interface
0 HSI0 clock management unit. This is used (amongst others) for USB.
While the usual (sed) script has been used to derive the linux clock
IDs from the data sheet, one manual tweak was applied to fix a typo
which we don't want to carry:
HSI0_USPDPDBG_USER -> HSI0_USBDPDBG_USER (note USB vs USP).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240423-hsi0-gs101-v1-1-2c3ddb50c720@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Both the PHYs of the EQOS interface and the FEC interface are supported
to be reset by I2C GPIO Expender. So add the support to reset PHYs.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx93-11x11-evk dts use the strongest driver strength for
default(high-speed), 100MHz(SDR50/DDR50/DDR52) and
200MHz(SDR104/HS200/HS400) timing. To make usdhc working appropriately for
each timing, add X1 drive strength to default timing and X3 drive
strength to 100MHz timing.
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sleep pinctrl settings for EQoS and FEC to save power when suspend.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the resource table to avoid conflict because iMX93 ROM use last 4KB
TCM aream. Also correct vdev1vring node name to align with reg.
Fixes: e1da729459 ("arm64: dts: imx93: enable CM33 for 11x11 EVK")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Config SDHC1 clock 400MHz to support eMMC HS400ES mode
2. The original usdhc2 and usdhc3 root clock is 200MHz. Then WIFI
on usdhc3 at SDR104 mode can work under 200MHz. But if imx93 work
under Low Drive mode, the usdhc3 pad signal is not good under 200MHz,
SDR104 mode can't work stable. Need to downgrade to 133MHz to let
WIFI work stable. To cover all the cases, for Norminal Drive mode,
keep usdhc root at 400MHz, then card(SD/wifi) can work at SDR104 mode
under 200MHz to get the best performance. For Low Drive mode,
bootloader need override usdhc root clock to 266MHz, and the
card(SD/wifi) work at SDR104 mode under 133MHz, can work stable.
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add dma support for lpspi[1..8]
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add dma support for lpi2c[1..8].
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use FSL_EDMA_RX for dma rx channel bitmask, which is intuitive.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PCI devices should have a compatible string based on the vendor and device
IDs. Add these to the Freescale ENETC devices.
Putting the PCI compatible string first as vendor and device ID is more
specific than a compatible without any device specific information.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PCI devices should use PCI interrupt binding for their interrupts assuming
they function as standard PCI interrupts. The embedded PCI devices in the
LS1028a are mapping the interrupts directly to the host interrupt
controller. While that works here, it is unusual.
Based on the reference manual, there is not any INTC or INTD to map, so
only INTA and INTB are mapped.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add cm40_i2c, wm8960 and sai[0,1,4,5] for imx8qxp-mek (SCH-38813).
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure both CSI2 clock-frequency and assigned-clock-rates
the same way. There does not seem to be any reason for keeping
the two CSI2 pixel clock set to different frequencies.
This also reduces first CSI2 clock from overdrive mode
frequency which is 500 MHz down below the regular mode
frequency of 400 MHz.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Our hardware department recently informed us that, according to
the specification, the QCA7000 should be operated with a
maximum SPI clock frequency of 12 MHz. Even if it appears to work
at a higher frequency, we should not take any risks here. A short
performance test showed no measurable loss of speed.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Our Tarragon platform uses a active-low signal to inform
the i.MX6ULL about the over-current detection.
Fixes: 5e4f393ccb ("ARM: dts: imx6ull: Add chargebyte Tarragon support")
Signed-off-by: Michael Heimpold <michael.heimpold@chargebyte.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unused clock-names 'mem'. Driver (sound/soc/fsl/fsl_esai.c.) never
use clock name 'mem'.
arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dtb: esai@2024000: clocks: [[2, 208], [2, 209], [2, 118], [2, 208], [2, 156]] is too long
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dtb: esai@2024000: clock-names:1: 'extal' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dtb: esai@2024000: clock-names:2: 'fsys' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dtb: esai@2024000: clock-names:3: 'spba' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dtb: esai@2024000: clock-names: ['core', 'mem', 'extal', 'fsys', 'spba'] is too long
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove undocumented compatible string 'fsl,imx6sx-esai', which never used
in driver sound/soc/fsl/fsl_esai.c.
Remove unused clock-names 'mem'. Driver never use clock name 'mem'.
Fix below warning:
arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: esai@2024000: compatible:0: 'fsl,imx6sx-esai' is not one of ['fsl,imx35-esai', 'fsl,imx6ull-esai', 'fsl,imx8qm-esai', 'fsl,vf610-esai']
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arm/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: esai@2024000: compatible: ['fsl,imx6sx-esai', 'fsl,imx35-esai'] is too long
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arm/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: esai@2024000: clocks: [[2, 239], [2, 240], [2, 152], [2, 239], [2, 196]] is too long
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: esai@2024000: clock-names:1: 'extal' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: esai@2024000: clock-names:2: 'fsys' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: esai@2024000: clock-names:3: 'spba' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,esai.yaml#
arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtb: esai@2024000: clock-names: ['core', 'mem', 'extal', 'fsys', 'spba'] is too long
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dt_has_supported_hw() function returns type bool. That means these
negative error codes are cast to true but the function should return
false instead.
Fixes: fa5aec9561 ("cpufreq: sun50i: Add support for opp_supported_hw")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
There is a compile warning because a NULL pointer check was added before
a struct was declared. This moves the NULL pointer check to after the
struct is declared and moves the struct assignment to after the NULL
pointer check.
Fixes: f661017e6d ("cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value")
Signed-off-by: Portia Stephens <portia.stephens@canonical.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
There are no more users that need the legacy idle quirk so let's drop
the legacy idle quirk handling. This simplifies the PM code to just
sysc_pm_ops with unified handling for all the interconnect targets.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the smartreflex driver no longer relying on the use of
pm_runtime_irq_safe(), we can finally drop the related legacy quirk
handling.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
