Modify driver to set the Write Same Divert Capability bit in the IOCInit
message for the firmware to know that the driver is capable of diverting
certain Write Same commands as defined by the MPI specification.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver uses a controller-wide flag to block ioctls when a controller
reset is in progress. This flag is set before controller reset is initiated
and cleared after the reset has completed.
Make the driver clear the controller-wide block ioctls flag after a
controller reset fails and the controller is marked unrecoverable.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 'flags' variable inside an MPI request is a bitfield and should
consequently be updated using a bitwise OR operation.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver did not remove the virtual disk that was exposed as hidden and
offline after the controller was reset.
Drive is removed from OS when firmware sends "device added" event with
hidden bit set or access status indicating inability to accept I/Os.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Link: https://lore.kernel.org/r/20240313100746.128951-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Link: https://lore.kernel.org/r/20240208105314.129095-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Convert Samsung Exynos5250/5420 SoC Display Port Controller bindings to
DT schema with a change: add power-domains, already used in DTS.
This Display Port controller is actually variant of Analogix Display
Port bridge, however new DT Schema does not reference analogix,dp.yaml,
because of incompatibilities in the driver. The analogix,dp.yaml
expects two ports, input and output, but Linux Exynos DP DRM driver and
DTS use only one port: output.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240313182855.14140-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Convert WM8974 audio CODEC bindings from text to dtschema.
Signed-off-by: Kartik Agarwala <agarwala.kartik@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240325181943.116733-1-agarwala.kartik@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fc663711b9 ("scsi: core: Remove the /proc/scsi/${proc_name}
directory earlier") fixed a bug related to modules loading/unloading, by
adding a call to scsi_proc_hostdir_rm() on scsi_remove_host(). But that led
to a potential duplicate call to the hostdir_rm() routine, since it's also
called from scsi_host_dev_release(). That triggered a regression report,
which was then fixed by commit be03df3d4b ("scsi: core: Fix a procfs host
directory removal regression"). The fix just dropped the hostdir_rm() call
from dev_release().
But it happens that this proc directory is created on scsi_host_alloc(),
and that function "pairs" with scsi_host_dev_release(), while
scsi_remove_host() pairs with scsi_add_host(). In other words, it seems the
reason for removing the proc directory on dev_release() was meant to cover
cases in which a SCSI host structure was allocated, but the call to
scsi_add_host() didn't happen. And that pattern happens to exist in some
error paths, for example.
Syzkaller causes that by using USB raw gadget device, error'ing on
usb-storage driver, at usb_stor_probe2(). By checking that path, we can see
that the BadDevice label leads to a scsi_host_put() after a SCSI host
allocation, but there's no call to scsi_add_host() in such path. That leads
to messages like this in dmesg (and a leak of the SCSI host proc
structure):
usb-storage 4-1:87.51: USB Mass Storage device detected
proc_dir_entry 'scsi/usb-storage' already registered
WARNING: CPU: 1 PID: 3519 at fs/proc/generic.c:377 proc_register+0x347/0x4e0 fs/proc/generic.c:376
The proper fix seems to still call scsi_proc_hostdir_rm() on dev_release(),
but guard that with the state check for SHOST_CREATED; there is even a
comment in scsi_host_dev_release() detailing that: such conditional is
meant for cases where the SCSI host was allocated but there was no calls to
{add,remove}_host(), like the usb-storage case.
This is what we propose here and with that, the error path of usb-storage
does not trigger the warning anymore.
Reported-by: syzbot+c645abf505ed21f931b5@syzkaller.appspotmail.com
Fixes: be03df3d4b ("scsi: core: Fix a procfs host directory removal regression")
Cc: stable@vger.kernel.org
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20240313113006.2834799-1-gpiccoli@igalia.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avri Altman <avri.altman@wdc.com> says:
Device management commands are constructed for query commands that are
being issued by the driver, but also for raw device management
commands originated by the bsg module, and recently, by the advanced
rpmb handler. Thus, the same code fragments, e.g. locking, composing
the command, composing the upiu etc., appear over and over. Remove
those duplications. Theoretically, there should be no functional
change.
Link: https://lore.kernel.org/r/20240309081104.5006-1-avri.altman@wdc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move some code fragments into ufshcd_prepare_req_desc_hdr() so it can be
used throughout.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240309081104.5006-5-avri.altman@wdc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move out some of the dev_cmd initializations so they can be used elsewhere.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240309081104.5006-4-avri.altman@wdc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move out the actual command issue from exec_dev_cmd it can be used
elsewhere. While at it, remove a redundant "lrbp->cmd = NULL" assignment.
Also, the device management commands that are originated from the
ufs-bsg code path, are being traced now, which wasn't the case before.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240309081104.5006-3-avri.altman@wdc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Group those 3 calls that repeat for every device management command into
lock and unlock handlers.
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20240309081104.5006-2-avri.altman@wdc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are no more users of the deprecated is_dma_mapped in struct
spi_message so it can be removed.
References in documentation and comments are also removed.
A few similar checks if xfer->tx_dma or xfer->rx_dma are not NULL are
also removed since these are now guaranteed to be NULL because they
were previously set only if is_dma_mapped was true.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240325-spi-remove-is_dma_mapped-v2-1-d08d62b61f1c@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to the SPI controller driver to use SPI MEM framework.
SPI subsystem utilizing the SPI memory operations allows to re-use
SPI controller drivers for both SPI NOR devices, regular SPI devices
as well as SPI NAND devices.
Add below functions of spi_mem_ops to support SPI MEM framework
- exec-op(): to execute the memory operations.
- supports_op(): to check if the memory operation is supported.
- adjust_op_size(): to split data transfers so that they don’t exceed the
max transfer size supported by the controller.
Suggested-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Co-developed-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Signed-off-by: Krishnamoorthi M <krishnamoorthi.m@amd.com>
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://msgid.link/r/20240229134544.3461757-1-Raju.Rangoju@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The limitation that all RT processes have to be in the root cgroup
before enabling cpu controller only applies if the CONFIG_RT_GROUP_SCHED
option is enabled in the running kernel. If a kernel does not have
CONFIG_RT_GROUP_SCHED enabled, RT processes can exist in a non-root
cgroup even when cpu controller is enabled. CPU sharing of RT processes
will not be under cgroup control, but other resources like memory can be.
Clarify this limitation to avoid confusion to users that are using
cgroup v2.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds support for AD7944 ADCs wired in "3-wire mode". (NOTE: 3-wire
is the datasheet name for this wiring configuration and has nothing to
do with SPI_3WIRE.)
In the 3-wire mode, the SPI controller CS line can be wired to the CNV
line on the ADC and used to trigger conversions rather that using a
separate GPIO line.
The turbo/chain mode compatibility check at the end of the probe
function is technically can't be triggered right now but adding it now
anyway so that we don't forget to add it later when support for
daisy-chaining is added.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240314-mainline-ad7944-3-wire-mode-v2-1-d469da0705d2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a statement with two semicolons. Remove the second one, it
is redundant.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240315091436.2430227-1-colin.i.king@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the new cleanup magic for handling mutexes in IIO. This allows us to
greatly simplify some code paths.
While at it, also use __free(kfree) where allocations are done and drop
obvious comment in iio_channel_read_min().
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240229-iio-use-cleanup-magic-v3-4-c3d34889ae3c@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the new cleanup magic for handling mutexes in IIO. This allows us to
greatly simplify some code paths.
Note that we keep the plain mutex calls in the
iio_device_release|acquire() APIs since in there the macros would likely
not help much (as we want to keep the lock acquired when he leave the
APIs).
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240229-iio-use-cleanup-magic-v3-1-c3d34889ae3c@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add wakeup from suspend for WoM when enabled and put accel in low-power
mode when suspended. Requires rewriting pwr_mgmt_1 register handling and
factorize out accel LPF settings. Use a low-power rate similar to the chip
sampling rate but always lower for a best match of the sampling rate while
saving power and adjust threshold to follow the required roc value.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240311160557.437337-5-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new interrupt handler for generating WoM event from int status register
bits. Launch from interrupt the trigger poll function for data buffer.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240311160557.437337-4-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add WoM (roc rising) event as accel x_or_y_or_z event for all chips >=
MPU-6500. This requires to create new MPU-6500 channels as default and
MPU-6050 channels for older chips.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240311160557.437337-3-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
WoM is a threshold test on accel value comparing actual sample with
previous one. It maps best to roc rising event.
Add support of a new WOM sensor and functions for handling the associated
roc_rising event. The event value is in SI units. Ensure WOM is stopped and
restarted at suspend-resume, handle usage with buffer data ready interrupt,
and handle change in sampling rate impacting already set roc value.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240311160557.437337-2-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The HDC3020 provides an active low reset signal that must be handled if
connected. Asserting this signal turns the device into Trigger-on Demand
measurement mode, reducing its power consumption when no measurements
are required like in low-power modes.
According to the datasheet, the longest "Reset Ready" is 3 ms, which is
only taken into account if the reset signal is defined.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240303-hdc3020-pm-v3-3-48bc02b5241b@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The HDC3020 provides an active low reset signal that is still not
described in the bindings.
Add reset-gpios to the bindings and the example.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240303-hdc3020-pm-v3-2-48bc02b5241b@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The HDC3020 sensor carries out periodic measurements during normal
operation, but as long as the power supply is enabled, it will carry on
in low-power modes. In order to avoid that and reduce power consumption,
the device can be switched to Trigger-on Demand mode, and if possible,
turn off its regulator.
According to the datasheet, the maximum "Power Up Ready" is 5 ms.
Add resume/suspend pm operations to manage measurement mode and
regulator state.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240303-hdc3020-pm-v3-1-48bc02b5241b@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a driver for the Analog Devices Inc. AD7944, AD7985, and
AD7986 ADCs. These are a family of pin-compatible ADCs that can sample
at rates up to 2.5 MSPS.
The initial driver adds support for sampling at lower rates using the
usual IIO triggered buffer and can handle all 3 possible reference
voltage configurations.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240304-ad7944-mainline-v5-2-f0a38cea8901@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a new binding for the Analog Devices, Inc. AD7944, AD7985, and
AD7986 ADCs.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240304-ad7944-mainline-v5-1-f0a38cea8901@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Include mod_devicetable.h explicitly to replace the dropped of.h
which included mod_devicetable.h indirectly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240304144037.1036390-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for: AD7172-2, AD7175-8, AD7177-2.
AD7172-4 does not feature an internal reference, check for external
reference presence.
Signed-off-by: Dumitru Ceclan <mitrutzceclan@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240306110956.13167-2-mitrutzceclan@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver support for Avago (Broadcom) APDS9306 Ambient Light Sensor.
It has two channels - ALS and CLEAR. The ALS (Ambient Light Sensor)
channel approximates the response of the human-eye providing direct
read out where the output count is proportional to ambient light levels.
It is internally temperature compensated and rejects 50Hz and 60Hz flicker
caused by artificial light sources. Hardware interrupt configuration is
optional. It is a low power device with 20 bit resolution and has
configurable adaptive interrupt mode and interrupt persistence mode.
The device also features inbuilt hardware gain, multiple integration time
selection options and sampling frequency selection options.
This driver also uses the IIO GTS (Gain Time Scale) Helpers Namespace for
Scales, Gains and Integration time implementation.
Signed-off-by: Subhajit Ghosh <subhajit.ghosh@tweaklogic.com>
Link: https://lore.kernel.org/r/20240309105031.10313-6-subhajit.ghosh@tweaklogic.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Include irq.h and irq level macro in the example for readability
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Subhajit Ghosh <subhajit.ghosh@tweaklogic.com>
Link: https://lore.kernel.org/r/20240309105031.10313-4-subhajit.ghosh@tweaklogic.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All devices covered by the binding have a vdd supply.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Subhajit Ghosh <subhajit.ghosh@tweaklogic.com>
Link: https://lore.kernel.org/r/20240309105031.10313-3-subhajit.ghosh@tweaklogic.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No need to rewrite the value, instead use 'else' branch.
This will also help further refactoring the code later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240304140650.977784-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In iio_device_alloc() when size of the private data is 0,
the private pointer is calculated to point behind the valid data.
Leave it NULL when no private data supplied.
Fixes: 6d4ebd565d ("iio: core: wrap IIO device into an iio_dev_opaque object")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240304140650.977784-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
