The TI DP83826 PHY can operate between two RMII modes:
- master mode (PHY operates from a 25MHz clock reference)
- slave mode (PHY operates from a 50MHz clock reference)
By default, the operation mode is configured by hardware straps.
Add support to configure the operation mode from within the driver.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI DP83826 PHY can operate in either MII mode or RMII mode.
By default, it is configured by straps.
It can also be configured by writing to the bit 5 of register 0x17 - RMII
and Status Register (RCSR).
When phydev->interface is rmii, rmii mode must be enabled, otherwise
mii mode must be set.
This prevents misconfiguration of hw straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add property ti,rmii-mode to support selecting the RMII operation mode
between:
- master mode (PHY operates from a 25MHz clock reference)
- slave mode (PHY operates from a 50MHz clock reference)
If not set, the operation mode is configured by hardware straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement bridge port isolation for KSZ switches. Enabling the isolation
of switch ports from each other while maintaining connectivity with the
CPU and other forwarding ports. For instance, to isolate swp1 and swp2
from each other, use the following commands:
- bridge link set dev swp1 isolated on
- bridge link set dev swp2 isolated on
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that we keep GRO flag in sync when XDP is disabled while
the device is closed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth sets NETIF_F_GRO automatically when XDP is enabled,
because both features use the same NAPI machinery.
The logic to clear NETIF_F_GRO sits in veth_disable_xdp() which
is called both on ndo_stop and when XDP is turned off.
To avoid the flag from being cleared when the device is brought
down, the clearing is skipped when IFF_UP is not set.
Bringing the device down should indeed not modify its features.
Unfortunately, this means that clearing is also skipped when
XDP is disabled _while_ the device is down. And there's nothing
on the open path to bring the device features back into sync.
IOW if user enables XDP, disables it and then brings the device
up we'll end up with a stray GRO flag set but no NAPI instances.
We don't depend on the GRO flag on the datapath, so the datapath
won't crash. We will crash (or hang), however, next time features
are sync'ed (either by user via ethtool or peer changing its config).
The GRO flag will go away, and veth will try to disable the NAPIs.
But the open path never created them since XDP was off, the GRO flag
was a stray. If NAPI was initialized before we'll hang in napi_disable().
If it never was we'll crash trying to stop uninitialized hrtimer.
Move the GRO flag updates to the XDP enable / disable paths,
instead of mixing them with the ndo_open / ndo_close paths.
Fixes: d3256efd8e ("veth: allow enabling NAPI even without XDP")
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: syzbot+039399a9b96297ddedca@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of Infineon SPI NOR flash devices support hybrid sector layout that
overlays 4KB sectors on a 256KB sector and SPI NOR framework recognizes
that by parsing SMPT and construct params->erase_map. The hybrid sector
layout is similar to CFI flash devices that have small sectors on top
and/or bottom address. In case of CFI flash devices, the erase map
information is parsed through CFI table and populated into
mtd->eraseregions so that users can create MTD partitions that aligned
with small sector boundaries. This patch provides the same capability to
SPI NOR flash devices that have non-uniform erase map.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/35d0962986e493b06c13bdf7ada8130a9966dc02.1708404584.git.Takahiro.Kuwano@infineon.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Introduce n_regions in spi_nor_erase_map structure and remove
SNOR_LAST_REGION flag. Loop logics that depend on the flag are also
reworked to use n_regions as loop condition.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Suggested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/eded84294bd81e966d6f423e578fc2cfb9a4a5b6.1708404584.git.Takahiro.Kuwano@infineon.com
[ta: update spi_nor_init_erase_cmd_list() and break the for loop sooner.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
For the clksel clocks we are still using the legacy ti,bit-shift property
instead of the standard reg property. We can now use the reg property, so
let's do that for the clksel clocks.
To add the reg property, we switch to use #address-cells = <1>.
For now let's not update the clock-dss-tv-fck as it seems to share the same
register bit as the clock-dss-96m-fck and would introduce more warnings.
Cc: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For the clksel clocks we are still using the legacy ti,bit-shift property
instead of the standard reg property. We can now use the reg property, so
let's do that for the clksel clocks.
To add the reg property, we switch to use #address-cells = <1>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Because of legacy reasons, the TI clksel composite clocks can have
overlapping reg properties, and use a custom ti,bit-shift property.
For the clksel clocks we can start using of the standard reg property
instead of the custom ti,bit-shift property.
To do this, let's add a ti_clk_get_legacy_bit_shift() helper, and make
ti_clk_get_reg_addr() populate the clock bit offset.
This makes it possible to update the devicetree files to use the reg
property one clock at a time.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to use #address-cells = <1> and start making use of the
standard reg property, let's prepare things to ignore the possible
address in the clock node name.
Unless the clock-output-names property is used, the legacy clocks still
fall back to matching the clock data based on the node name.
We use cleanup.h to simplify the return path for freeing tmp.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After a couple recent changes in LLVM, there is a warning (or error with
CONFIG_WERROR=y or W=e) from the compile time fortify source routines,
specifically the memset() in copy_to_user_tmpl().
In file included from net/xfrm/xfrm_user.c:14:
...
include/linux/fortify-string.h:438:4: error: call to '__write_overflow_field' declared with 'warning' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
438 | __write_overflow_field(p_size_field, size);
| ^
1 error generated.
While ->xfrm_nr has been validated against XFRM_MAX_DEPTH when its value
is first assigned in copy_templates() by calling validate_tmpl() first
(so there should not be any issue in practice), LLVM/clang cannot really
deduce that across the boundaries of these functions. Without that
knowledge, it cannot assume that the loop stops before i is greater than
XFRM_MAX_DEPTH, which would indeed result a stack buffer overflow in the
memset().
To make the bounds of ->xfrm_nr clear to the compiler and add additional
defense in case copy_to_user_tmpl() is ever used in a path where
->xfrm_nr has not been properly validated against XFRM_MAX_DEPTH first,
add an explicit bound check and early return, which clears up the
warning.
Cc: stable@vger.kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1985
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmXb0T4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5YQH/3eCV90sNGch0Y94
8rtTdqFrVx7QPNl0pz+Mo6OUIKUUHvTuwime16ckLxG+3x2Y3I0MjP1edd1NB99C
Kje//JTpaZBPpTZ/jY4u8B1Shov2Drdx/J4NFnE/9rG6yXzKQBtvON/xAxXDCVHT
mLhst2LR0FeCSMk9jAX6CoqUPEgwlylNyAetKxaDQgoHl4GTZC7FDO17WxyjpIxe
1rVHsrV9Eq8kD4uxrzpTYWgZrwTObPmlZjvefa1JfzSwRNABIBJj/C1nra1Zc1oi
b7xVaXS1cMOxrtuuG00fmHsPnWivu0tuND7H3/yLd1mRCZAPSsVbVvrI/KNtoeV4
1euINlY=
=7IFt
-----END PGP SIGNATURE-----
Merge v6.8-rc6 into drm-next
Thomas Zimmermann asked to backmerge -rc6 for drm-misc branches,
there's a few same-area-changed conflicts (xe and amdgpu mostly) that
are getting a bit too annoying.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The next timer (re-)evaluation, with the purpose of entering/updating
the dyntick mode, can happen from 3 sites and none of them are relevant
while the CPU is offline:
1) The idle loop:
a) From the quick check helping the cpuidle governor to heuristically
predict the best C-state.
b) While stopping the tick.
But if the CPU is offline, the tick has been cancelled and there is
consequently no need to further stop the tick.
2) Remote expiry: when a CPU remotely expires global timers on behalf of
another CPU, the latter target's next timer is re-evaluated
afterwards. However remote expîry doesn't happen on offline CPUs.
3) IRQ exit: on nohz_full mode, the tick is (re-)evaluated on IRQ exit.
But full dynticks is disabled on offline CPUs.
Therefore it is safe to assume that no next dyntick timer lookup can
be performed on offline CPUs.
Assert this expectation to report any surprise.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-17-frederic@kernel.org
The timekeeping duty is handed over from the outgoing CPU on stop
machine, then the oneshot tick is stopped right after. Therefore it's
guaranteed that the current CPU isn't the timekeeper upon its last call
to idle.
Besides, calling tick_nohz_idle_stop_tick() while the dying CPU goes
into idle suggests that the tick is going to be stopped while it is
actually stopped already from the appropriate CPU hotplug state.
Remove the confusing call and the obsolete case handling and convert it
to a sanity check that verifies the above assumption.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-16-frederic@kernel.org
The timekeeping duty is handed over from the outgoing CPU within stop
machine. This works well if CONFIG_NO_HZ_COMMON=n or the tick is in
high-res mode. However in low-res dynticks mode, the tick isn't
cancelled until the clockevent is shut down, which can happen later. The
tick may therefore fire again once IRQs are re-enabled on stop machine
and until IRQs are disabled for good upon the last call to idle.
That's so many opportunities for a timekeeper to go idle and the
outgoing CPU to take over that duty. This is why
tick_nohz_idle_stop_tick() is called one last time on idle if the CPU
is seen offline: so that the timekeeping duty is handed over again in
case the CPU has re-taken the duty.
This means there are two timekeeping handovers on CPU down hotplug with
different undocumented constraints and purposes:
1) A handover on stop machine for !dynticks || highres. All online CPUs
are guaranteed to be non-idle and the timekeeping duty can be safely
handed-over. The hrtimer tick is cancelled so it is guaranteed that in
dynticks mode the outgoing CPU won't take again the duty.
2) A handover on last idle call for dynticks && lowres. Setting the
duty to TICK_DO_TIMER_NONE makes sure that a CPU will take over the
timekeeping.
Prepare for consolidating the handover to a single place (the first one)
with shutting down the low-res tick as well from
tick_cancel_sched_timer() as well. This will simplify the handover and
unify the tick cancellation between high-res and low-res.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-15-frederic@kernel.org
The nohz mode field tells about low resolution nohz mode or high
resolution nohz mode but it doesn't tell about high resolution non-nohz
mode.
In order to retrieve the latter state, tick_cancel_sched_timer() must
fiddle with struct hrtimer's internals to guess if the tick has been
initialized in high resolution.
Move instead the nohz mode field information into the tick flags and
provide two new bits: one to know if the tick is in nohz mode and
another one to know if the tick is in high resolution. The combination
of those two flags provides all the needed informations to determine
which of the three tick modes is running.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-14-frederic@kernel.org
The individual bitfields of struct tick_sched must be modified from
IRQs disabled places, otherwise local modifications can race due to them
sharing the same memory storage.
The recent move of the "got_idle_tick" bitfield to its own storage shows
that the use of these bitfields, as pretty as they look, can be as much
error prone.
In order to avoid future issues of the like and make sure that those
bitfields are safely accessed, move those flags to an explicit mask
along with a mutator function performing the basic IRQs disabled sanity
check.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-13-frederic@kernel.org
tick_nohz_idle_got_tick() is called by cpuidle_reflect() within the idle
loop with interrupts enabled. This function modifies the struct
tick_sched's bitfield "got_idle_tick". However this bitfield is stored
within the same mask as other bitfields that can be modified from
interrupts.
Fortunately so far it looks like the only race that can happen is while
writing ->got_idle_tick to 0, an interrupt fires and writes the
->idle_active field to 0. It's then possible that the interrupted write
to ->got_idle_tick writes back the old value of ->idle_active back to 1.
However if that happens, the worst possible outcome is that the time
spent between that interrupt and the upcoming call to
tick_nohz_idle_exit() is accounted as idle, which is negligible quantity.
Still all the bitfield writes within this struct tick_sched's shadow
mask should be IRQ-safe. Therefore move this bitfield out to its own
storage to avoid further suprises.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-12-frederic@kernel.org
The full-nohz update function checks if the nohz mode is active before
proceeding. It considers one exception though: if the tick is already
stopped even though the nohz mode is inactive, it still moves on in
order to update/restart the tick if needed.
However in order for the tick to be stopped, the nohz_mode has to be
either NOHZ_MODE_LOWRES or NOHZ_MODE_HIGHRES. Therefore it doesn't make
sense to test if the tick is stopped before verifying NOHZ_MODE_INACTIVE
mode.
Remove the needless related condition.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-11-frederic@kernel.org
The broadcast shutdown code is executed through a random explicit call
within stop machine from the outgoing CPU.
However the tick broadcast is a midware between the tick callback and
the clocksource, therefore it makes more sense to shut it down after the
tick callback and before the clocksource drivers.
Move it instead to the common tick shutdown CPU hotplug state where
related operations can be ordered from highest to lowest level.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-10-frederic@kernel.org
The tick hrtimer is cancelled right before hrtimers are migrated. This
is done from the hrtimer subsystem even though it shouldn't know about
its actual users.
Move instead the tick hrtimer cancellation to the relevant CPU hotplug
state that aims at centralizing high level tick shutdown operations so
that the related flow is easy to follow.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-9-frederic@kernel.org
During the CPU offlining process, the various timer tick features are
shut down from scattered places, sometimes from teardown callbacks on
stop machine, sometimes through explicit calls, sometimes from the
control CPU after the CPU died. The reason why these shutdown operations
are spread around is not always clear and it makes the tick lifecycle
hard to follow.
The tick should be shut down in order from highest to lowest level:
On stop machine from the dying CPU (high-level):
1) Hand-over the timekeeping duty (tick_handover_do_timer())
2) Cancel the tick implementation called by the clockevent callback
(tick_cancel_sched_timer())
3) Shutdown broadcasting (tick_offline_cpu() / tick_broadcast_offline())
On stop machine from the dying CPU (low-level):
4) Shutdown clockevents drivers (CPUHP_AP_*_TIMER_STARTING states)
From the control CPU after the CPU died (low-level):
5) Shutdown/unregister/cleanup clockevents for the dead CPU
(tick_cleanup_dead_cpu())
Instead the current order is 2, 4 (both from CPU hotplug states), then
1 and 3 through direct calls. This layout and order don't make much
sense. The operations 1, 2, 3 should be gathered together and in order.
Sort this situation with creating a new TICK shut-down CPU hotplug state
and start with introducing the timekeeping duty hand-over there. The
state must precede hrtimers migration because the tick hrtimer will be
stopped from it in a further patch.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-8-frederic@kernel.org
The tick sched structure is already cleared from tick_cancel_sched_timer(),
so there is no need to clear that field again.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-7-frederic@kernel.org
tick_nohz_stop_sched_tick() is only about NOHZ_full and not about
dynticks-idle. Reflect that in the function name to avoid confusion.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-6-frederic@kernel.org
Avoid ifdeferry if it can be converted to IS_ENABLED() whenever possible
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-5-frederic@kernel.org
tick-sched.c is only built when CONFIG_TICK_ONESHOT=y, which is selected
only if CONFIG_NO_HZ_COMMON=y or CONFIG_HIGH_RES_TIMERS=y. Therefore
the related ifdeferry in this file is needless and can be removed.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-4-frederic@kernel.org
tick_nohz_lowres_handler() does the same work as
tick_nohz_highres_handler() plus the clockevent device reprogramming, so
make the former reuse the latter and rename it accordingly.
Signed-off-by: Peng Liu <liupeng17@lenovo.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-3-frederic@kernel.org
The ts->sched_timer initialization work of tick_nohz_switch_to_nohz()
is almost the same as that of tick_setup_sched_timer(), so adjust the
latter to get it reused by tick_nohz_switch_to_nohz().
This also makes the low resolution mode sched_timer benefit from the tick
skew boot option.
Signed-off-by: Peng Liu <liupeng17@lenovo.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240225225508.11587-2-frederic@kernel.org
Add brcm,nand-ecc-use-strap to get ecc and spare area size settings from
board boot strap for broadband board designs because they do not specify
ecc setting in dts but rather using the strap setting.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-7-william.zhang@broadcom.com
Add brcm,wp-not-connected property to have an option for disabling this
feature on broadband board design that does not connect WP pin.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-6-william.zhang@broadcom.com
Update the descriptions to reflect different families of broadband SoC and
use the general name bcmbca for ARM based SoC.
Remove the requirement of interrupts property to reflect the driver
code and only require interrupt-names when interrupts property present.
Also add myself to the list of maintainers.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: David Regan <dregan@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-5-william.zhang@broadcom.com
Update log level messages so that more critical messages can be logged
to console and help the troubleshooting with field devices.
Signed-off-by: David Regan <dregan@broadcom.com>
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240223034758.13753-4-william.zhang@broadcom.com
The SLAB_MEM_SPREAD flag used to be implemented in SLAB, which was
removed as of v6.8-rc1, so it became a dead flag since the commit
16a1d96835 ("mm/slab: remove mm/slab.c and slab_def.h"). And the
series[1] went on to mark it obsolete to avoid confusion for users.
Here we can just remove all its users, which has no functional change.
[1] https://lore.kernel.org/all/20240223-slab-cleanup-flags-v2-1-02f1753e8303@suse.cz/
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
FMC2 IP supports up to 4 chip select. On MP1 SoC, only 2 of them are
available when on MP25 SoC, the 4 chip select are available.
Let's use a platform data structure for parameters that will differ.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240219140505.85794-4-christophe.kerello@foss.st.com
Use dma_get_slave_caps API to get the max burst size of a DMA channel.
For MP1 SoCs, MDMA is used and the max burst size is 128.
For MP25 SoC, DMA3 is used and the max burst size is 64.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240219140505.85794-3-christophe.kerello@foss.st.com
Add a compatible string to support MP25 SoC.
FMC2 IP supports up to 4 chip select. On MP1 SoC, only 2 of them are
available when on MP25 SoC, the 4 chip select are available.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240219140505.85794-2-christophe.kerello@foss.st.com
clang-16 warns about mismatched function prototypes:
drivers/mtd/nand/raw/lpc32xx_mlc.c:783:29: error: cast from 'irqreturn_t (*)(int, struct lpc32xx_nand_host *)' (aka 'enum irqreturn (*)(int, struct lpc32xx_nand_host *)') to 'irq_handler_t' (aka 'enum irqreturn (*)(int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Change the interrupt handler to the normal way of just passing
a void* pointer and converting it inside the function..
Fixes: 70f7cb78ec ("mtd: add LPC32xx MLC NAND driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240213100146.455811-1-arnd@kernel.org
This is an effort to get rid of all multiplications from allocation
functions in order to prevent integer overflows [1].
As the "chip" variable is a pointer to "struct mtk_nfc_nand_chip" and
this structure ends in a flexible array:
struct mtk_nfc_nand_chip {
[...]
u8 sels[] __counted_by(nsels);
};
the preferred way in the kernel is to use the struct_size() helper to
do the arithmetic instead of the argument "size + count * size" in the
devm_kzalloc() function.
This way, the code is more readable and safer.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/160 [2]
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Erick Archer <erick.archer@gmx.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240211091633.4545-1-erick.archer@gmx.com
Scrambling mode is enabled by value (1 << 19). NFC_CMD_SCRAMBLER_ENABLE
is already (1 << 19), so there is no need to shift it again in CMDRWGEN
macro.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Cc: <Stable@vger.kernel.org>
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240210214551.441610-1-avkrasnov@salutedevices.com
The variable bbtblocks is being assigned a value that is never
read. The assignment is redundant and can be removed.
Cleans up clang scan build warning:
drivers/mtd/nand/raw/nand_bbt.c:579:3: warning: Value stored to
'bbtblocks' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240209174019.3933233-1-colin.i.king@gmail.com
Encoding bitmask flags into offset worsen the code readability. The
erase type mask and flags should be stored in dedicated members. Also,
erase_map.uniform_erase_type can be removed as it is redundant.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Suggested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://lore.kernel.org/r/8e5e9e4081ed9f16ea9dce30693304a4b54d19b1.1708404584.git.Takahiro.Kuwano@infineon.com
[ta: remove spi_nor_region_end()]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
As far as anybody can tell, this product never shipped. If it did,
it shipped in 2007 and nobody has access to one any more. Remove the
mtd NOR driver.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231208224703.1603264-2-willy@infradead.org
In two functions the variable timeo is being initialized with a value
that is never read, it is being re-assigned later on. The initializations
are redundant and can be removed.
Cleans up clang scan build warning:
warning: Value stored to 'timeo' during its initialization is never
read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240215140106.2062858-1-colin.i.king@gmail.com