A number function comments state the function return non-zero on
failure but in reality they can only return 0 on success and < 0 on
error.
Update the comments to say < 0 on error to match the behavior.
While at it, improve cat_val() comment to state that 0 means the test
was run (either pass or fail).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
perf_event_open_llc_miss() calls ctrlc_handler() to cleanup if
perf_event_open() returns an error. Those cleanups, however, are not
the responsibility of perf_event_open_llc_miss() and it thus interferes
unnecessarily with the usual cleanup pattern. Worse yet,
ctrlc_handler() calls exit() in the end preventing the ordinary cleanup
done in the calling function from executing.
ctrlc_handler() should only be used as a signal handler, not during
normal error handling.
Remove call to ctrlc_handler() from perf_event_open_llc_miss(). As
unmounting resctrlfs and test cleanup are already handled properly
by error rollbacks in the calling functions, no other changes are
necessary.
Suggested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
A number of functions in the resctrl selftests return errno. It is
problematic because errno is positive which is often counterintuitive.
Also, every site returning errno prints the error message already with
ksft_perror() so there is not much added value in returning the precise
error code.
Simply convert all places returning errno to return -1 that is typical
userspace error code in case of failures.
While at it, improve resctrl_val() comment to state that 0 means the
test was run (either pass or fail).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The resctrl selftest code contains a number of perror() calls. Some of
them come with hash character and some don't. The kselftest framework
provides ksft_perror() that is compatible with test output formatting
so it should be used instead of adding custom hash signs.
Some perror() calls are too far away from anything that sets error.
For those call sites, ksft_print_msg() must be used instead.
Convert perror() to ksft_perror() or ksft_print_msg().
Other related changes:
- Remove hash signs
- Remove trailing stops & newlines from ksft_perror()
- Add terminating newlines for converted ksft_print_msg()
- Use consistent capitalization
- Small fixes/tweaks to typos & grammar of the messages
- Extract error printing out of PARENT_EXIT() to be able to
differentiate
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The ACPI in some SoundWire laptops has a spk-id-gpios property but
it points to the wrong Device node. This patch adds a workaround to
try to get the GPIO directly from the correct Device node.
If the attempt to get the GPIOs from the property fails, the workaround
looks for the SDCA node "AF01", which is where the GpioIo resource is
defined. If this exists, a spk-id-gpios mapping is added to that node
and then the GPIO is got from that node using the property.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://msgid.link/r/20240209111840.1543630-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the names given to a few of the GPIO pins. The original names
were unknowingly based on the header from a pre-production board. The
production board has a slightly different pin assignment for the 40-pin
GPIO header.
Fixes: 3900160e16 ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240125201943.90476-2-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Due to internal differences between LLVM and GCC the current
implementation for the CO-RE macros does not fit GCC parser, as it will
optimize those expressions even before those would be accessible by the
BPF backend.
As examples, the following would be optimized out with the original
definitions:
- As enums are converted to their integer representation during
parsing, the IR would not know how to distinguish an integer
constant from an actual enum value.
- Types need to be kept as temporary variables, as the existing type
casts of the 0 address (as expanded for LLVM), are optimized away by
the GCC C parser, never really reaching GCCs IR.
Although, the macros appear to add extra complexity, the expanded code
is removed from the compilation flow very early in the compilation
process, not really affecting the quality of the generated assembly.
Signed-off-by: Cupertino Miranda <cupertino.miranda@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240213173543.1397708-1-cupertino.miranda@oracle.com
The rock-pi-e currently comes in 4 board spins, the latest one (v1.21)
swaps out the Realtek 8211e PHY for an 8211f PHY. Therefore modify the
phy-handle name to be more generic.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Link: https://lore.kernel.org/r/20240116204103.29318-1-twoerner@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix rk3288 hdmi ports node so that it matches the
rockchip,dw-hdmi.yaml binding with some reordering
to align with the (new) documentation about
property ordering.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/cc3a9b4f-076d-4660-b464-615003b6a066@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
kvm_pgtable_stage2_free_unlinked() does the final put_page() on the
root page of the sub-tree before returning, so remove the additional
put_page() invocations in the callers.
Cc: Ricardo Koller <ricarkol@google.com>
Fixes: f6a27d6dc5 ("KVM: arm64: Drop last page ref in kvm_pgtable_stage2_free_removed()")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240212193052.27765-1-will@kernel.org
Most Rockchip hdmi nodes are part of a power domain.
Add a power-domains property and include it to the example
with some reordering to align with the (new) documentation
about property ordering.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/5c45527a-e218-40a3-8e71-a5815417e5f7@gmail.com
The hdmi-connector nodes are now functional and the new way to model
hdmi ports nodes with both in and output port subnodes. Unfortunately
with the conversion to YAML the old method with only an input port node
was used. Later the new method was also added to the binding.
A binding must be unambiguously, so remove the old port property
entirely and make port@0 and port@1 a requirement as all
upstream dts files are updated as well and because checking
deprecated stuff is a bit pointless.
Update the example to avoid use of the removed property.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/a493c65e-7cf9-455f-95d5-8c98cad35710@gmail.com
[Changes from V1:
- Avoid conflict by rebasing with latest master.]
Some BPF tests use loop unrolling compiler pragmas that are clang
specific and not supported by GCC. These pragmas, along with their
GCC equivalences are:
#pragma clang loop unroll_count(N)
#pragma GCC unroll N
#pragma clang loop unroll(full)
#pragma GCC unroll 65534
#pragma clang loop unroll(disable)
#pragma GCC unroll 1
#pragma unroll [aka #pragma clang loop unroll(enable)]
There is no GCC equivalence to this pragma. It enables unrolling on
loops that the compiler would not ordinarily unroll even with
-O2|-funroll-loops, but it is not equivalent to full unrolling
either.
This patch adds a new header progs/bpf_compiler.h that defines the
following macros, which correspond to each pair of compiler-specific
pragmas above:
__pragma_loop_unroll_count(N)
__pragma_loop_unroll_full
__pragma_loop_no_unroll
__pragma_loop_unroll
The selftests using loop unrolling pragmas are then changed to include
the header and use these macros in place of the explicit pragmas.
Tested in bpf-next master.
No regressions.
Signed-off-by: Jose E. Marchesi <jose.marchesi@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/bpf/20240208203612.29611-1-jose.marchesi@oracle.com
Compiling with CONFIG_BPF_SYSCALL & !CONFIG_BPF_JIT throws the below
warning:
"WARN: resolve_btfids: unresolved symbol bpf_cpumask"
Fix it by adding the appropriate #ifdef.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: David Vernet <void@manifault.com>
Link: https://lore.kernel.org/bpf/20240208100115.602172-1-hbathini@linux.ibm.com
The sdmmc node already have a "&sdmmc_det" for pinctrl which switch the
GPIO0A4 to sdmmc detect function, no need to define a separate "cd-gpios".
RK3588 has force_jtage feature which is enable JTAG function via sdmmc
pins automatically when there is no SD card insert, this feature will
need the GPIO0A4 works in sdmmc_det function like other mmc signal instead
of GPIO function, or else the force_jtag can not auto be disabled when
SD card insert.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20240201034621.1970279-1-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add two tests to ensure fentry programs cannot attach to
bpf_spin_{lock,unlock}() helpers. The tracing_failure.c files
can be used in the future for other tracing failure cases.
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240207070107.335341-1-yonghong.song@linux.dev
Currently tracing is supposed not to allow for bpf_spin_{lock,unlock}()
helper calls. This is to prevent deadlock for the following cases:
- there is a prog (prog-A) calling bpf_spin_{lock,unlock}().
- there is a tracing program (prog-B), e.g., fentry, attached
to bpf_spin_lock() and/or bpf_spin_unlock().
- prog-B calls bpf_spin_{lock,unlock}().
For such a case, when prog-A calls bpf_spin_{lock,unlock}(),
a deadlock will happen.
The related source codes are below in kernel/bpf/helpers.c:
notrace BPF_CALL_1(bpf_spin_lock, struct bpf_spin_lock *, lock)
notrace BPF_CALL_1(bpf_spin_unlock, struct bpf_spin_lock *, lock)
notrace is supposed to prevent fentry prog from attaching to
bpf_spin_{lock,unlock}().
But actually this is not the case and fentry prog can successfully
attached to bpf_spin_lock(). Siddharth Chintamaneni reported
the issue in [1]. The following is the macro definition for
above BPF_CALL_1:
#define BPF_CALL_x(x, name, ...) \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
typedef u64 (*btf_##name)(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)); \
u64 name(__BPF_REG(x, __BPF_DECL_REGS, __BPF_N, __VA_ARGS__)) \
{ \
return ((btf_##name)____##name)(__BPF_MAP(x,__BPF_CAST,__BPF_N,__VA_ARGS__));\
} \
static __always_inline \
u64 ____##name(__BPF_MAP(x, __BPF_DECL_ARGS, __BPF_V, __VA_ARGS__))
#define BPF_CALL_1(name, ...) BPF_CALL_x(1, name, __VA_ARGS__)
The notrace attribute is actually applied to the static always_inline function
____bpf_spin_{lock,unlock}(). The actual callback function
bpf_spin_{lock,unlock}() is not marked with notrace, hence
allowing fentry prog to attach to two helpers, and this
may cause the above mentioned deadlock. Siddharth Chintamaneni
actually has a reproducer in [2].
To fix the issue, a new macro NOTRACE_BPF_CALL_1 is introduced which
will add notrace attribute to the original function instead of
the hidden always_inline function and this fixed the problem.
[1] https://lore.kernel.org/bpf/CAE5sdEigPnoGrzN8WU7Tx-h-iFuMZgW06qp0KHWtpvoXxf1OAQ@mail.gmail.com/
[2] https://lore.kernel.org/bpf/CAE5sdEg6yUc_Jz50AnUXEEUh6O73yQ1Z6NV2srJnef0ZrQkZew@mail.gmail.com/
Fixes: d83525ca62 ("bpf: introduce bpf_spin_lock")
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240207070102.335167-1-yonghong.song@linux.dev
The binding doesn't define interrupts and adding such a definition was
refused because it's unclear how they should ever be used and the
relevant registers are outside the PWM range. So drop them fixing
several dtbs_check warnings.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/5551846d-62cd-4b72-94f4-07541e726c37@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The px30 has two spi controllers with two chip-selects each.
The num-cs property is specified as the total number of chip
selects a controllers has and is used since 2020 to find uses
of chipselects outside that range in the Rockchip spi driver.
Without the property set, the default is 1, so spi devices
using the second chipselect will not be created.
Fixes: eb1262e3cc ("spi: spi-rockchip: use num-cs property and ctlr->enable_gpiods")
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240119101656.965744-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A hardware switch can set the rs485 transceiver into half or full duplex
mode.
Switching to the half-duplex mode requires the user to enable em485 on
uart5 using ioctl, DE/RE are both connected to GPIO0_B5 which is the
RTS signal for uart0. Implement GPIO0_B5 as rts-gpios with RTS_ON_SEND
option enabled (default) so that driver mode gets enabled while sending
(RTS high) and receiver mode gets enabled while not sending (RTS low).
In full-duplex mode (em485 is disabled), DE is connected to GPIO0_B5 and
RE is grounded (enabled). Since GPIO0_B5 is implemented as rts-gpios, the
driver mode gets enabled whenever we want to send something and RE is not
affected (always enabled) in this case by the state of RTS.
Signed-off-by: Farouk Bouabid <farouk.bouabid@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240208-dev-rx-enable-v6-2-39e68e17a339@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A hardware switch can set the rs485 transceiver into half or full duplex
mode.
Switching to the half-duplex mode requires the user to enable em485 on
uart5 using ioctl, DE/RE are both connected to GPIO2_C3 which is the
RTS signal for uart0. Implement GPIO2_C3 as rts-gpios with RTS_ON_SEND
option enabled (default) so that driver mode gets enabled while sending
(RTS high) and receiver mode gets enabled while not sending (RTS low).
In full-duplex mode (em485 is disabled), DE is connected to GPIO2_C3 and
RE is grounded (enabled). Since GPIO2_C3 is implemented as rts-gpios, the
driver mode gets enabled whenever we want to send something and RE is not
affected (always enabled) in this case by the state of RTS.
Signed-off-by: Farouk Bouabid <farouk.bouabid@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240208-dev-rx-enable-v6-1-39e68e17a339@theobroma-systems.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since 20d59ee551 ("libbpf: add bpf_core_cast() macro"), libbpf is now
exporting a const arg version of bpf_rdonly_cast(). This causes the
following conflicting type error when generating kfunc prototypes from
BTF:
In file included from skeleton/pid_iter.bpf.c:5:
/home/dxu/dev/linux/tools/bpf/bpftool/bootstrap/libbpf/include/bpf/bpf_core_read.h:297:14: error: conflicting types for 'bpf_rdonly_cast'
extern void *bpf_rdonly_cast(const void *obj__ign, __u32 btf_id__k) __ksym __weak;
^
./vmlinux.h:135625:14: note: previous declaration is here
extern void *bpf_rdonly_cast(void *obj__ign, u32 btf_id__k) __weak __ksym;
This is b/c the kernel defines bpf_rdonly_cast() with non-const arg.
Since const arg is more permissive and thus backwards compatible, we
change the kernel definition as well to avoid conflicting type errors.
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/bpf/dfd3823f11ffd2d4c838e961d61ec9ae8a646773.1707080349.git.dxu@dxuuu.xyz
Add support for the Powkiddy RGB10MAX3. The Powkiddy RGB10MAX3 is a
handheld gaming device with a 720p 5.0 inch screen powered by the
Rockchip RK3566 SoC. It includes a Realtek 8723ds WiFi/BT module, 2 ADC
joysticks powered by a 4-way muxed ADC channel, and several GPIO
face buttons. There are 2 SDMMC slots (sdmmc1 and sdmmc3), 3 pwm
controlled LEDs, and the device includes 1GB of RAM.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240212184950.52210-8-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Powkiddy RGB10MAX3 is a handheld gaming device made by Powkiddy and
powered by the Rockchip RK3566 SoC.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212184950.52210-7-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Move the vdd_cpu regulator to the device specific dts. This is in
preparation of adding the Powkiddy RGB10MAX3 device, which uses
a different vendor for the CPU regulator at a different i2c address.
Also add a phandle to the bluetooth device so that we can change the
compatible string for the RGB10MAX3. This device uses the same pinouts
but a different bluetooth device.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240212184950.52210-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Document the rotation property for rocktech,jh057n00900 panels.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212184950.52210-4-macroalpha82@gmail.com
The Powkiddy RGB10MAX3 is a handheld device with a 5 inch 720x1280
display panel with a Sitronix ST7703 display controller. The panel
is installed rotated 270 degrees.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212184950.52210-3-macroalpha82@gmail.com
The RGB10MAX3 panel is a panel specific to the Powkiddy RGB10MAX3
handheld device that measures 5 inches diagonally with a resolution
of 720x1280.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212184950.52210-2-macroalpha82@gmail.com
The RK3588 VO GRF needs a clock. This adds the clock to the allowed
properties, makes it mandatory for the RK3588 VO grf and disallows it
for any other Rockchip grf.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240213163609.44930-2-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Paolo Abeni says:
====================
selftests: net: more pmtu.sh fixes
The mentioned test is still flaky, unusally enough in 'fast'
environments.
Patch 2/2 [try to] address the existing issues, while patch 1/2
introduces more strict tests for the existing net helpers, to hopefully
prevent future pain.
====================
Link: https://lore.kernel.org/r/cover.1707731086.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The netdev CI is reporting failures for the pmtu test:
[ 115.929264] br0: port 2(vxlan_a) entered forwarding state
# 2024/02/08 17:33:22 socat[7871] E bind(7, {AF=10 [0000:0000:0000:0000:0000:0000:0000:0000]:50000}, 28): Address already in use
# 2024/02/08 17:33:22 socat[7877] E write(7, 0x5598fb6ff000, 8192): Connection refused
# TEST: IPv6, bridged vxlan4: PMTU exceptions [FAIL]
# File size 0 mismatches exepcted value in locally bridged vxlan test
The root cause is apparently a socket created by a previous iteration
of the relevant loop still lasting in LAST_ACK state.
Note that even the file size check is racy, the receiver process dumping
the file could still be running in background
Allow the listener to bound on the same local port via SO_REUSEADDR and
collect file output file size only after the listener completion.
Fixes: 136a1b434b ("selftests: net: test vxlan pmtu exceptions with tcp")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/4f51c11a1ce7ca7a4dabd926cffff63dadac9ba1.1707731086.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The helper waiting for a listener port can match any socket whose
hexadecimal representation of source or destination addresses
matches that of the given port.
Additionally, any socket state is accepted.
All the above can let the helper return successfully before the
relevant listener is actually ready, with unexpected results.
So far I could not find any related failure in the netdev CI, but
the next patch is going to make the critical event more easily
reproducible.
Address the issue matching the port hex only vs the relevant socket
field and additionally checking the socket state for TCP sockets.
Fixes: 3bdd9fd29c ("selftests/net: synchronize udpgro tests' tx and rx connection")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/192b3dbc443d953be32991d1b0ca432bd4c65008.1707731086.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Devicetree binding maintainers expect the example DTS in a binding to
show the usage of only this one particular binding, without unrelated
device nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212150524.81819-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Add to the list of schema contents expected keywords with their
explanation: additionalProperties and unevaluatedProperties.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212150524.81819-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240208105327.129159-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
SmartRG described itself as a CPE manufacturer and produced few home
network devices (e.g. wireless routers). Their SmartRG SR400ac router
(smartrg,sr400ac) is covered by in-Linux DT binding and DTS file.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212140839.27150-1-zajec5@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Apparently on Qualcomm SM8550 and SM8650 the FastRPC compute callbacks
are DMA coherent:
sm8650-qrd.dtb: fastrpc: compute-cb@2: 'dma-coherent' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240212110827.59302-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Kernel test robot reports sparse warning:
sparse warnings: (new ones prefixed by >>)
>> drivers/of/base.c:1337:73: sparse: sparse: incorrect type in initializer
(different base types) @@ expected restricted __be32 @@ got int @@
drivers/of/base.c:1337:73: sparse: expected restricted __be32
drivers/of/base.c:1337:73: sparse: got int
Thus, Make explicit conversions to mute warning(Although BE and LE are
exactly same in binary representation for 0/~0).
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402042134.GEb3Bgwl-lkp@intel.com/
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Link: https://lore.kernel.org/r/20240205024033.3572617-1-dawei.li@shingroup.cn
Signed-off-by: Rob Herring <robh@kernel.org>
Since commit d492cc2573 ("driver core: device.h: make struct
bus_type a const *"), the driver core can properly handle constant
struct bus_type, move the host1x_bus_type variable to be a constant
structure as well, placing it into read-only memory which can not be
modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240213-bus_cleanup-host1x-v1-1-54ec51b5d14f@marliere.net