This patch resolves a spelling error in the filesystem documentation.
It is submitted as part of my application to the "Linux Kernel Bug
Fixing Spring Unpaid 2024" mentorship program of the Linux Kernel
Foundation.
Signed-off-by: Vincenzo Mezzela <vincenzo.mezzela@gmail.com>
Link: https://lore.kernel.org/r/20240208162032.109184-1-vincenzo.mezzela@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
The low power policy board type was introduced to allow systems
to get into deep states reliably. Before it was introduced `min_power`
was causing problems for a number of drives. New power policies
`min_power_with_partial` and `med_power_with_dipm` have been introduced
which provide a more stable baseline for systems.
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
[cassel: rebase patch and fix trivial conflicts]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
AHCI 1.3.3, 7.3.1.1 Software Flow for Hot Plug Removal Detection states:
"To reliably detect hot plug removals, software must disable interface
power management.
Software should perform the following initialization on a port after a
device is attached:
-Set PxSCTL.IPM to 3h to disable interface power management state
transitions.
-Set PxCMD.ALPE to ‘0’ to disable aggressive power management.
-Ensure PxIE.PRCE is set to ‘1’ to enable interrupts on hot plug removals.
-Disable device initiated interface power management by issuing the
appropriate SET FEATURES command."
Further, AHCI 1.3.3, 7.3 Native Hot Plug Support states:
"The HBA shall set the PxSERR.DIAG.X bit to ‘1’ when a COMINIT is received
from the device. Hot plug insertions are detected via the PxIS.PCS bit
that directly reflects the PxSERR.DIAG.X bit. The HBA shall set the
PxSERR.DIAG.N bit to ‘1’ when the HBA’s internal PhyRdy signal changes
state.
Hot plug removals are detected via the PxIS.PRCS bit that directly
reflects the PxSERR.DIAG.N bit. Note that PxSERR.DIAG.N is also set
to ‘1’ on insertions and during interface power management entry/exit."
ahci_set_lpm() already disables the PxIS.PRCS interrupt if setting a
LPM policy != ATA_LPM_MAX_POWER, so we cannot detect hot plug removals
when LPM policy != ATA_LPM_MAX_POWER.
We do have PxIS.PCS interrupt enabled even for LPM policy !=
ATA_LPM_MAX_POWER, so we should theoretically still be able to detect
hot plug insertions even when LPM is enabled.
However, in practise, for LPM policy ATA_LPM_MED_POWER_WITH_DIPM,
ATA_LPM_MIN_POWER_WITH_PARTIAL, and ATA_LPM_MIN_POWER, if there is
no link enabled, sata_link_scr_lpm() will set SControl.DET = 0x4,
which will transition the port to the "P:Offline" state.
The P:Offline mode is described in SATA Gold 3.5a:
4.1.1.103 Phy offline:
"In this mode the host Phy is forced off and the host Phy does not
recognize nor respond to COMINIT or COMWAKE. This mode is entered by
setting the DET field of the SControl register to 0100b. This is a
mechanism for the host to turn off its Phy."
So in the P:Offline state the PHY does not recognize the unsolicited
COMINIT which is sent on a hot plug insertion.
While we could change sata_link_scr_lpm() to never power off an external
port for LPM policy != ATA_LPM_MAX_POWER (in order be able to handle hot
plug insertions), we still would not be able to handle hot plug removals.
Thus, simply modify ahci_update_initial_lpm_policy() to not enable LPM if
the port advertises itself as an external port, as this function is
already being used to set/override the initial LPM policy.
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
There is no need for ahci_update_initial_lpm_policy() to take hpriv as a
parameter, it can easily be derived from the ata_port.
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
A hotplug capable port is an external port, so mark it as such.
We even say this ourselves in libata-scsi.c:
/* set scsi removable (RMB) bit per ata bit, or if the
* AHCI port says it's external (Hotplug-capable, eSATA).
*/
This also matches the terminology used in AHCI 1.3.1
(the keyword to search for is "externally accessible").
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Move the marking of an external port earlier in the call chain.
This is needed for further cleanups.
No functional change intended.
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Refactor pci_epf_alloc_space() API to accept "epc_features" as a parameter.
This is a preparatory work to make the API more robust.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240207213922.1796533-2-cassel@kernel.org
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This was still referring to cfg80211_chandef_primary_freq(),
fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: b82730bf57 ("wifi: cfg80211/mac80211: move puncturing into chandef")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
__le32 and __le64 types should be used with le32_to_cpu() and
le64_to_cpu() and __user is needed for pointers referencing
guest memory, as sparse helpfully points out.
Fixes: e9f12b5fff ("RISC-V: KVM: Implement SBI STA extension")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401020142.lwFEDK5v-lkp@intel.com/
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
__le32 and __le64 types should be used with le32_to_cpu() and
le64_to_cpu(), as sparse helpfully points out.
Fixes: fdf68acccf ("RISC-V: paravirt: Implement steal-time support")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401011933.hL9zqmKo-lkp@intel.com/
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
steal_time is not used outside paravirt.c, make it static,
as sparse suggested.
Fixes: fdf68acccf ("RISC-V: paravirt: Implement steal-time support")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
commit 0a31bd5f2b ("KMEM_CACHE(): simplify slab cache creation")
introduces a new macro.
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
SP 800-56Br2, Section 7.1.1 [1] specifies that:
1. If m does not satisfy 1 < m < (n – 1), output an indication that m is
out of range, and exit without further processing.
Similarly, Section 7.1.2 of the same standard specifies that:
1. If the ciphertext c does not satisfy 1 < c < (n – 1), output an
indication that the ciphertext is out of range, and exit without further
processing.
This range is slightly more conservative than RFC3447, as it also
excludes RSA fixed points 0, 1, and n - 1.
[1] https://doi.org/10.6028/NIST.SP.800-56Br2
Signed-off-by: Joachim Vandersmissen <git@jvdsn.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rework the AER reset and recovery flow to take into account root port
integrated devices that gets reset between the error detected and the
slot reset callbacks.
In adf_error_detected() the devices is gracefully shut down. The worker
threads are disabled, the error conditions are notified to listeners and
through PFVF comms and finally the device is reset as part of
adf_dev_down().
In adf_slot_reset(), the device is brought up again. If SRIOV VFs were
enabled before reset, these are re-enabled and VFs are notified of
restarting through PFVF comms.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the driver detects an heartbeat failure, it starts the recovery
flow. Set a limit so that the number of events is limited in case the
heartbeat status is read too frequently.
Signed-off-by: Furong Zhou <furong.zhou@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Expose the `auto_reset` sysfs attribute to configure the driver to reset
the device when a fatal error is detected.
When auto reset is enabled, the driver resets the device when it detects
either an heartbeat failure or a fatal error through an interrupt.
This patch is based on earlier work done by Shashank Gupta.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Notify a fatal error condition and optionally reset the device in
the following cases:
* if the device reports an uncorrectable fatal error through an
interrupt
* if the heartbeat feature detects that the device is not
responding
This patch is based on earlier work done by Shashank Gupta.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When a Physical Function (PF) is reset, SR-IOV gets disabled, making the
associated Virtual Functions (VFs) unavailable. Even after reset and
using pci_restore_state, VFs remain uncreated because the numvfs still
at 0. Therefore, it's necessary to reconfigure SR-IOV to re-enable VFs.
This commit introduces the ADF_SRIOV_ENABLED configuration flag to cache
the SR-IOV enablement state. SR-IOV is only re-enabled if it was
previously configured.
This commit also introduces a dedicated workqueue without
`WQ_MEM_RECLAIM` flag for enabling SR-IOV during Heartbeat and CPM error
resets, preventing workqueue flushing warning.
This patch is based on earlier work done by Shashank Gupta.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the PFVF logic to handle restart and recovery. This adds the
following functions:
* adf_pf2vf_notify_fatal_error(): allows the PF to notify VFs that the
device detected a fatal error and requires a reset. This sends to
VF the event `ADF_PF2VF_MSGTYPE_FATAL_ERROR`.
* adf_pf2vf_wait_for_restarting_complete(): allows the PF to wait for
`ADF_VF2PF_MSGTYPE_RESTARTING_COMPLETE` events from active VFs
before proceeding with a reset.
* adf_pf2vf_notify_restarted(): enables the PF to notify VFs with
an `ADF_PF2VF_MSGTYPE_RESTARTED` event after recovery, indicating that
the device is back to normal. This prompts VF drivers switch back to
use the accelerator for workload processing.
These changes improve the communication and synchronization between PF
and VF drivers during system restart and recovery processes.
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Disable arbitration to avoid new requests to be processed before
resetting a device.
This is needed so that new requests are not fetched when an error is
detected.
Signed-off-by: Furong Zhou <furong.zhou@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add error notify method to report a fatal error event to all the
subsystems registered. In addition expose an API,
adf_notify_fatal_error(), that allows to trigger a fatal error
notification asynchronously in the context of a workqueue.
This will be invoked when a fatal error is detected by the ISR or
through Heartbeat.
Signed-off-by: Furong Zhou <furong.zhou@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a mechanism that allows to inject a heartbeat error for testing
purposes.
A new attribute `inject_error` is added to debugfs for each QAT device.
Upon a write on this attribute, the driver will inject an error on the
device which can then be detected by the heartbeat feature.
Errors are breaking the device functionality thus they require a
device reset in order to be recovered.
This functionality is not compiled by default, to enable it
CRYPTO_DEV_QAT_ERROR_INJECTION must be set.
Signed-off-by: Damian Muszynski <damian.muszynski@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Lucas Segarra Fernandez <lucas.segarra.fernandez@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Markas Rapoportas <markas.rapoportas@intel.com>
Signed-off-by: Mun Chun Yep <mun.chun.yep@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
virtqueue_enable_cb() will call virtqueue_poll() which will check if
queue is broken at beginning, so remove the virtqueue_is_broken() call
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>