Commit graph

111,142 commits

Author SHA1 Message Date
Xiang wangx
959edef658 ppp: Fix typo in comment
Delete the redundant word 'the'.

Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Link: https://lore.kernel.org/r/20220616142624.3397-1-wangxiang@cdjrlc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-17 20:17:04 -07:00
Yinjun Zhang
382f99c442 nfp: add support for .get_pauseparam()
Show correct pause frame parameters for nfp. These parameters cannot
be configured, so .set_pauseparam() is not implemented. With this
change:

 #ethtool --show-pause enp1s0np0
 Pause parameters for enp1s0np0:
 Autonegotiate:  off
 RX:             on
 TX:             on

Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220616133358.135305-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-17 20:13:03 -07:00
Oleksij Rempel
7a49f21930 net: dsa: ar9331: fix potential dead lock on mdio access
Rework MDIO locking to avoid potential  circular locking:

 WARNING: possible circular locking dependency detected
 5.19.0-rc1-ar9331-00017-g3ab364c7c48c #5 Not tainted
 ------------------------------------------------------
 kworker/u2:4/68 is trying to acquire lock:
 81f3c83c (ar9331:1005:(&ar9331_mdio_regmap_config)->lock){+.+.}-{4:4}, at: regmap_write+0x50/0x8c

 but task is already holding lock:
 81f60494 (&bus->mdio_lock){+.+.}-{4:4}, at: mdiobus_read+0x40/0x78

 which lock already depends on the new lock.

 the existing dependency chain (in reverse order) is:

 -> #1 (&bus->mdio_lock){+.+.}-{4:4}:
        lock_acquire+0x2d4/0x360
        __mutex_lock+0xf8/0x384
        mutex_lock_nested+0x2c/0x38
        mdiobus_write+0x44/0x80
        ar9331_sw_bus_write+0x50/0xe4
        _regmap_raw_write_impl+0x604/0x724
        _regmap_bus_raw_write+0x9c/0xb4
        _regmap_write+0xdc/0x1a0
        _regmap_update_bits+0xf4/0x118
        _regmap_select_page+0x108/0x138
        _regmap_raw_read+0x25c/0x288
        _regmap_bus_read+0x60/0x98
        _regmap_read+0xd4/0x1b0
        _regmap_update_bits+0xc4/0x118
        regmap_update_bits_base+0x64/0x8c
        ar9331_sw_irq_bus_sync_unlock+0x40/0x6c
        __irq_set_handler+0x7c/0xac
        ar9331_sw_irq_map+0x48/0x7c
        irq_domain_associate+0x174/0x208
        irq_create_mapping_affinity+0x1a8/0x230
        ar9331_sw_probe+0x22c/0x388
        mdio_probe+0x44/0x70
        really_probe+0x200/0x424
        __driver_probe_device+0x290/0x298
        driver_probe_device+0x54/0xe4
        __device_attach_driver+0xe4/0x130
        bus_for_each_drv+0xb4/0xd8
        __device_attach+0x104/0x1a4
        bus_probe_device+0x48/0xc4
        device_add+0x600/0x800
        mdio_device_register+0x68/0xa0
        of_mdiobus_register+0x2bc/0x3c4
        ag71xx_probe+0x6e4/0x984
        platform_probe+0x78/0xd0
        really_probe+0x200/0x424
        __driver_probe_device+0x290/0x298
        driver_probe_device+0x54/0xe4
        __driver_attach+0x17c/0x190
        bus_for_each_dev+0x8c/0xd0
        bus_add_driver+0x110/0x228
        driver_register+0xe4/0x12c
        do_one_initcall+0x104/0x2a0
        kernel_init_freeable+0x250/0x288
        kernel_init+0x34/0x130
        ret_from_kernel_thread+0x14/0x1c

 -> #0 (ar9331:1005:(&ar9331_mdio_regmap_config)->lock){+.+.}-{4:4}:
        check_noncircular+0x88/0xc0
        __lock_acquire+0x10bc/0x18bc
        lock_acquire+0x2d4/0x360
        __mutex_lock+0xf8/0x384
        mutex_lock_nested+0x2c/0x38
        regmap_write+0x50/0x8c
        ar9331_sw_mbus_read+0x74/0x1b8
        __mdiobus_read+0x90/0xec
        mdiobus_read+0x50/0x78
        get_phy_device+0xa0/0x18c
        fwnode_mdiobus_register_phy+0x120/0x1d4
        of_mdiobus_register+0x244/0x3c4
        devm_of_mdiobus_register+0xe8/0x100
        ar9331_sw_setup+0x16c/0x3a0
        dsa_register_switch+0x7dc/0xcc0
        ar9331_sw_probe+0x370/0x388
        mdio_probe+0x44/0x70
        really_probe+0x200/0x424
        __driver_probe_device+0x290/0x298
        driver_probe_device+0x54/0xe4
        __device_attach_driver+0xe4/0x130
        bus_for_each_drv+0xb4/0xd8
        __device_attach+0x104/0x1a4
        bus_probe_device+0x48/0xc4
        deferred_probe_work_func+0xf0/0x10c
        process_one_work+0x314/0x4d4
        worker_thread+0x2a4/0x354
        kthread+0x134/0x13c
        ret_from_kernel_thread+0x14/0x1c

 other info that might help us debug this:

  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(&bus->mdio_lock);
                                lock(ar9331:1005:(&ar9331_mdio_regmap_config)->lock);
                                lock(&bus->mdio_lock);
   lock(ar9331:1005:(&ar9331_mdio_regmap_config)->lock);

  *** DEADLOCK ***

 5 locks held by kworker/u2:4/68:
  #0: 81c04eb4 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x1e4/0x4d4
  #1: 81f0de78 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work+0x1e4/0x4d4
  #2: 81f0a880 (&dev->mutex){....}-{4:4}, at: __device_attach+0x40/0x1a4
  #3: 80c8aee0 (dsa2_mutex){+.+.}-{4:4}, at: dsa_register_switch+0x5c/0xcc0
  #4: 81f60494 (&bus->mdio_lock){+.+.}-{4:4}, at: mdiobus_read+0x40/0x78

 stack backtrace:
 CPU: 0 PID: 68 Comm: kworker/u2:4 Not tainted 5.19.0-rc1-ar9331-00017-g3ab364c7c48c #5
 Workqueue: events_unbound deferred_probe_work_func
 Stack : 00000056 800d4638 81f0d64c 00000004 00000018 00000000 80a20000 80a20000
         80937590 81ef3858 81f0d760 3913578a 00000005 8045e824 81f0d600 a8db84cc
         00000000 00000000 80937590 00000a44 00000000 00000002 00000001 ffffffff
         81f0d6a4 80982d7c 0000000f 20202020 80a20000 00000001 80937590 81ef3858
         81f0d760 3913578a 00000005 00000005 00000000 03bd0000 00000000 80e00000
         ...
 Call Trace:
 [<80069db0>] show_stack+0x94/0x130
 [<8045e824>] dump_stack_lvl+0x54/0x8c
 [<800c7fac>] check_noncircular+0x88/0xc0
 [<800ca068>] __lock_acquire+0x10bc/0x18bc
 [<800cb478>] lock_acquire+0x2d4/0x360
 [<807b84c4>] __mutex_lock+0xf8/0x384
 [<807b877c>] mutex_lock_nested+0x2c/0x38
 [<804ea640>] regmap_write+0x50/0x8c
 [<80501e38>] ar9331_sw_mbus_read+0x74/0x1b8
 [<804fe9a0>] __mdiobus_read+0x90/0xec
 [<804feac4>] mdiobus_read+0x50/0x78
 [<804fcf74>] get_phy_device+0xa0/0x18c
 [<804ffeb4>] fwnode_mdiobus_register_phy+0x120/0x1d4
 [<805004f0>] of_mdiobus_register+0x244/0x3c4
 [<804f0c50>] devm_of_mdiobus_register+0xe8/0x100
 [<805017a0>] ar9331_sw_setup+0x16c/0x3a0
 [<807355c8>] dsa_register_switch+0x7dc/0xcc0
 [<80501468>] ar9331_sw_probe+0x370/0x388
 [<804ff0c0>] mdio_probe+0x44/0x70
 [<804d1848>] really_probe+0x200/0x424
 [<804d1cfc>] __driver_probe_device+0x290/0x298
 [<804d1d58>] driver_probe_device+0x54/0xe4
 [<804d2298>] __device_attach_driver+0xe4/0x130
 [<804cf048>] bus_for_each_drv+0xb4/0xd8
 [<804d200c>] __device_attach+0x104/0x1a4
 [<804d026c>] bus_probe_device+0x48/0xc4
 [<804d108c>] deferred_probe_work_func+0xf0/0x10c
 [<800a0ffc>] process_one_work+0x314/0x4d4
 [<800a17fc>] worker_thread+0x2a4/0x354
 [<800a9a54>] kthread+0x134/0x13c
 [<8006306c>] ret_from_kernel_thread+0x14/0x1c
[

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220616112550.877118-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-17 20:11:14 -07:00
Oleksij Rempel
46e31db55d net: macb: fix negative max_mtu size for sama5d3
JML register on probe will return zero . This register is configured
later on macb_init_hw() which is called on open.
Since we have zero, after header and FCS length subtraction we will get
negative max_mtu size. This issue was affecting DSA drivers with MTU support
(for example KSZ9477).

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 11:42:35 +01:00
Kees Cook
2c0ab32b73 hinic: Replace memcpy() with direct assignment
Under CONFIG_FORTIFY_SOURCE=y and CONFIG_UBSAN_BOUNDS=y, Clang is bugged
here for calculating the size of the destination buffer (0x10 instead of
0x14). This copy is a fixed size (sizeof(struct fw_section_info_st)), with
the source and dest being struct fw_section_info_st, so the memcpy should
be safe, assuming the index is within bounds, which is UBSAN_BOUNDS's
responsibility to figure out.

Avoid the whole thing and just do a direct assignment. This results in
no change to the executable code.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: netdev@vger.kernel.org
Cc: llvm@lists.linux.dev
Link: https://github.com/ClangBuiltLinux/linux/issues/1592
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 11:31:18 +01:00
Oleksij Rempel
225b0ed27e net: ag71xx: fix discards 'const' qualifier warning
Current kernel will compile this driver with warnings. This patch will
fix it.

drivers/net/ethernet/atheros/ag71xx.c: In function 'ag71xx_fast_reset':
drivers/net/ethernet/atheros/ag71xx.c:996:31: warning: passing argument 2 of 'ag71xx_hw_set
_macaddr' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
  996 |  ag71xx_hw_set_macaddr(ag, dev->dev_addr);
      |                            ~~~^~~~~~~~~~
drivers/net/ethernet/atheros/ag71xx.c:951:69: note: expected 'unsigned char *' but argument
 is of type 'const unsigned char *'
  951 | static void ag71xx_hw_set_macaddr(struct ag71xx *ag, unsigned char *mac)
      |                                                      ~~~~~~~~~~~~~~~^~~
drivers/net/ethernet/atheros/ag71xx.c: In function 'ag71xx_open':
drivers/net/ethernet/atheros/ag71xx.c:1441:32: warning: passing argument 2 of 'ag71xx_hw_se
t_macaddr' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
 1441 |  ag71xx_hw_set_macaddr(ag, ndev->dev_addr);
      |                            ~~~~^~~~~~~~~~
drivers/net/ethernet/atheros/ag71xx.c:951:69: note: expected 'unsigned char *' but argument
 is of type 'const unsigned char *'
  951 | static void ag71xx_hw_set_macaddr(struct ag71xx *ag, unsigned char *mac)
      |                                                      ~~~~~~~~~~~~~~~^~~

Fixes: adeef3e321 ("net: constify netdev->dev_addr")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 11:04:45 +01:00
Ong Boon Leong
ab21cf9209 net: stmmac: make mdio register skips PHY scanning for fixed-link
stmmac_mdio_register() lacks fixed-link consideration and only skip PHY
scanning if it has done DT style PHY discovery. So, for DT or ACPI _DSD
setting of fixed-link, the PHY scanning should not happen.

v2: fix incorrect order related to fwnode that is not caught in non-DT
    platform.

Tested-by: Emilio Riva <emilio.riva@ericsson.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 10:55:35 +01:00
Ong Boon Leong
72edaf39fc stmmac: intel: add phy-mode and fixed-link ACPI _DSD setting support
Currently, phy_interface for TSN controller instance is set based on its
PCI Device ID. For SGMII PHY interface, phy_interface default to
PHY_INTERFACE_MODE_SGMII. As C37 AN supports both SGMII and 1000BASE-X
mode, we add support for 'phy-mode' ACPI _DSD for port-specific
and customer platform specific customization.

v3: use fwnode_get_phy_mode() as suggested by Andrew Lunn in
https://patchwork.kernel.org/comment/24895330/

v2:
For platform that sets 'fixed-link' using ACPI _DSD, we will unset
xpcs_an_inband within stmmac. Thanks to Russell King for his comment in
https://patchwork.kernel.org/comment/24890222/

v1:
Thanks to Andrew Lunn's guidance in
https://patchwork.kernel.org/comment/24827101/

Tested-by: Emilio Riva <emilio.riva@ericsson.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 10:55:35 +01:00
Ong Boon Leong
b47aec885b net: pcs: xpcs: add CL37 1000BASE-X AN support
For CL37 1000BASE-X AN, DW xPCS does not support C22 method but offers
C45 vendor-specific MII MMD for programming.

We also add the ability to disable Autoneg (through ethtool for certain
network switch that supports 1000BASE-X (1000Mbps and Full-Duplex) but
not Autoneg capability.

v4: Fixes to comment from Russell King. Thanks!
    https://patchwork.kernel.org/comment/24894239/
    Make xpcs_modify_changed() as private, change to use
    mdiodev_modify_changed() for cleaner code.

v3: Fixes to issues spotted by Russell King. Thanks!
    https://patchwork.kernel.org/comment/24890210/
    Use phylink_mii_c22_pcs_decode_state(), remove unnecessary
    interrupt clearing and skip speed & duplex setting if AN
    is enabled.

v2: Fixes to issues spotted by Russell King in v1. Thanks!
    https://patchwork.kernel.org/comment/24826650/
    Use phylink_mii_c22_pcs_encode_advertisement() and implement
    C45 MII ADV handling since IP only support C45 access.

Tested-by: Emilio Riva <emilio.riva@ericsson.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 10:55:35 +01:00
Ong Boon Leong
c82386310d stmmac: intel: prepare to support 1000BASE-X phy interface setting
Currently, intel_speed_mode_2500() redundantly fix-up phy_interface to
PHY_INTERFACE_MODE_SGMII if the underlying controller is in 1000Mbps
SGMII mode. The value of phy_interface has been initialized earlier.

This patch removes such redundancy to prepare for setting 1000BASE-X
mode for certain hardware platform configuration.

Also update the intel_mgbe_common_data() to include 1000BASE-X setup.

Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 10:55:35 +01:00
Ong Boon Leong
fa9c562f97 net: make xpcs_do_config to accept advertising for pcs-xpcs and sja1105
xpcs_config() has 'advertising' input that is required for C37 1000BASE-X
AN in later patch series. So, we prepare xpcs_do_config() for it.

For sja1105, xpcs_do_config() is used for xpcs configuration without
depending on advertising input, so set to NULL.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 10:55:35 +01:00
Petr Machata
4ec2feb26c mlxsw: Add a resource describing number of RIFs
The Spectrum ASIC has a limit on how many L3 devices (called RIFs) can be
created. The limit depends on the ASIC and FW revision, and mlxsw reads it
from the FW. In order to communicate both the number of RIFs that there can
be, and how many are taken now (i.e. occupancy), introduce a corresponding
devlink resource.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 10:31:33 +01:00
Petr Machata
b9840fe035 mlxsw: Keep track of number of allocated RIFs
In order to expose number of RIFs as a resource, it is going to be handy
to have the number of currently-allocated RIFs as a single number.
Introduce such.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 10:31:33 +01:00
Amit Cohen
4b1cc357f8 mlxsw: Trap ARP packets at layer 3 instead of layer 2
Currently, the traps 'ARP_REQUEST' and 'ARP_RESPONSE' occur at layer 2.
To allow the packets to be flooded, they are configured with the action
'MIRROR_TO_CPU' which means that the CPU receives a replica of the packet.

Today, Spectrum ASICs also support trapping ARP packets at layer 3. This
behavior is better, then the packets can just be trapped and there is no
need to mirror them. An additional motivation is that using the traps at
layer 2, the ARP packets are dropped in the router as they do not have an
IP header, then they are counted as error packets, which might confuse
users.

Add the relevant traps for layer 3 and use them instead of the existing
traps. There is no visible change to user space.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-17 10:31:33 +01:00
Raju Lakkaraju
311abcdddc net: phy: add support to get Master-Slave configuration
Add support to Master-Slave configuration and state

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:45:48 -07:00
Raju Lakkaraju
46b777ad9a net: lan743x: Add support to SGMII 1G and 2.5G
Add SGMII access read and write functions
Add support to SGMII 1G and 2.5G for PCI11010/PCI11414 chips

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:45:48 -07:00
Raju Lakkaraju
6b3768ac8e net: lan743x: Add support to Secure-ON WOL
Add support to Magic Packet Detection with Secure-ON for PCI11010/PCI11414 chips

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:45:48 -07:00
Raju Lakkaraju
9aeb87d2b5 net: lan743x: Add support to LAN743x register dump
Add support to LAN743x common register dump

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:45:48 -07:00
Alvin Šipraga
a48b6e44a9 net: dsa: realtek: rtl8365mb: handle PHY interface modes correctly
Realtek switches in the rtl8365mb family always have at least one port
with a so-called external interface, supporting PHY interface modes such
as RGMII or SGMII. The purpose of this patch is to improve the driver's
handling of these ports.

A new struct rtl8365mb_chip_info is introduced together with a static
array of such structs. An instance of this struct is added for each
supported switch, distinguished by its chip ID and version. Embedded in
each chip_info struct is an array of struct rtl8365mb_extint, describing
the external interfaces available. This is more specific than the old
rtl8365mb_extint_port_map, which was only valid for switches with up to
6 ports.

The struct rtl8365mb_extint also contains a bitmask of supported PHY
interface modes, which allows the driver to distinguish which ports
support RGMII. This corrects a previous mistake in the driver whereby it
was assumed that any port with an external interface supports RGMII.
This is not actually the case: for example, the RTL8367S has two
external interfaces, only the second of which supports RGMII. The first
supports only SGMII and HSGMII. This new design will make it easier to
add support for other interface modes.

Finally, rtl8365mb_phylink_get_caps() is fixed up to return supported
capabilities based on the external interface properties described above.
This addresses Vladimir's point in the linked thread that the
capabilities are not actually a function of the DSA port type: Although
most typical applications will treat the ports with internal PHY as user
ports, there is no actual hardware limitation preventing one from using
them as a CPU port. Equally, ports with external interface(s) may well
be treated as user ports, even though it is typical to use those ports
as CPU ports.

Link: https://lore.kernel.org/netdev/20220510192301.5djdt3ghoavxulhl@bang-olufsen.dk/
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:47 -07:00
Alvin Šipraga
b3456030f5 net: dsa: realtek: rtl8365mb: remove learn_limit_max private data member
The variable is just assigned the value of a macro, so it can be
removed.

Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:47 -07:00
Alvin Šipraga
ca5ecd4246 net: dsa: realtek: rtl8365mb: correct the max number of ports
The maximum number of ports is actually 11, according to two
observations:

1. The highest port ID used in the vendor driver is 10. Since port IDs
   are indexed from 0, and since DSA follows the same numbering system,
   this means up to 11 ports are to be presumed.

2. The registers with port mask fields always amount to a maximum port
   mask of 0x7FF, corresponding to a maximum 11 ports.

In view of this, I also deleted the comment.

Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:47 -07:00
Alvin Šipraga
b325159d00 net: dsa: realtek: rtl8365mb: remove port_mask private data member
There is no real need for this variable: the line change interrupt mask
is sufficiently masked out when getting linkup_ind and linkdown_ind in
the interrupt handler.

Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:46 -07:00
Alvin Šipraga
5eb1a23840 net: dsa: realtek: rtl8365mb: rename macro RTL8367RB -> RTL8367RB_VB
The official name of this switch is RTL8367RB-VB, not RTL8367RB. There
is also an RTL8367RB-VC which is rather different. Change the name of
the CHIP_ID/_VER macros for reasons of consistency.

Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:46 -07:00
Alex Elder
81765eeac1 net: ipa: move more code out of gsi_channel_update()
Move the processing done for TX channels in gsi_channel_update()
into gsi_evt_ring_rx_update().  The called function is called for
both RX and TX channels, so rename it to be gsi_evt_ring_update().
As a result, this code no longer assumes events in an event ring are
associated with just one channel.

Because all events in a ring are handled in that function, we can
move the call to gsi_trans_move_complete() there, and can ring the
event ring doorbell there as well after all new events in the ring
have been processed.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:04 -07:00
Alex Elder
9f1c3ad654 net: ipa: call gsi_evt_ring_rx_update() unconditionally
When an RX transaction completes, we update the trans->len field to
contain the actual number of bytes received.  This is done in a loop
in gsi_evt_ring_rx_update().

Change that function so it checks the data transfer direction
recorded in the transaction, and only updates trans->len for RX
transfers.

Then call it unconditionally.  This means events for TX endpoints
will run through the loop without otherwise doing anything, but
this will change shortly.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:04 -07:00
Alex Elder
2f48fb0edc net: ipa: pass GSI pointer to gsi_evt_ring_rx_update()
The only reason the event ring's channel pointer is needed in
gsi_evt_ring_rx_update() is so we can get at its GSI pointer.

We can pass the GSI pointer as an argument, along with the event
ring ID, and thereby avoid using the event ring channel pointer.
This is another step toward no longer assuming an event ring
services a single channel.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:03 -07:00
Alex Elder
8eec783195 net: ipa: don't pass channel when mapping transaction
Change gsi_channel_trans_map() so it derives the channel used from
the transaction.  Pass the index of the *first* TRE used by the
transaction, and have the called function account for the fact that
the last one used is what's important.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:03 -07:00
Alex Elder
dd5a046cbb net: ipa: don't assume one channel per event ring
In gsi_evt_ring_rx_update(), use gsi_event_trans() repeatedly
to find the transaction associated with an event, rather than
assuming consecutive events are associated with the same channel.
This removes the only caller of gsi_trans_pool_next(), so get rid
of it.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:44:03 -07:00
Rasmus Villemoes
5c2d0a6a07 net: phy: dp83867: implement support for io_impedance_ctrl nvmem cell
We have a board where measurements indicate that the current three
options - leaving IO_IMPEDANCE_CTRL at the (factory calibrated) reset
value or using one of the two boolean properties to set it to the
min/max value - are too coarse.

Implement support for the newly added binding allowing device tree to
specify an nvmem cell containing an appropriate value for this
specific board.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:29:06 -07:00
Jakub Kicinski
9cbc991126 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
No conflicts.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 20:13:52 -07:00
Yang Yingliang
2e7bf4a6af net: axienet: add missing error return code in axienet_probe()
It should return error code in error path in axienet_probe().

Fixes: 00be43a74c ("net: axienet: make the 64b addresable DMA depends on 64b archectures")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220616062917.3601-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-16 11:08:38 -07:00
Haiyang Zhang
7a8938cd02 net: mana: Add support of XDP_REDIRECT action
Add a handler of the XDP_REDIRECT return code from a XDP program. The
packets will be flushed at the end of each RX/CQ NAPI poll cycle.
ndo_xdp_xmit() is implemented by sharing the code in mana_xdp_tx().
Ethtool per queue counters are added for XDP redirect and xmit operations.

Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-06-16 10:40:25 +02:00
Dexuan Cui
1566e7d620 net: mana: Add the Linux MANA PF driver
This minimal PF driver runs on bare metal.
Currently Ethernet TX/RX works. SR-IOV management is not supported yet.

Signed-off-by: Dexuan Cui <decui@microsoft.com>
Co-developed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-06-16 10:40:25 +02:00
Christian 'Ansuel' Marangi
8bca458990 net: ethernet: stmmac: reset force speed bit for ipq806x
Some bootloader may set the force speed regs even if the actual
interface should use autonegotiation between PCS and PHY.
This cause the complete malfuction of the interface.

To fix this correctly reset the force speed regs if a fixed-link is not
defined in the DTS. With a fixed-link node correctly configure the
forced speed regs to handle any misconfiguration by the bootloader.

Reported-by: Mark Mentovai <mark@moxienet.com>
Co-developed-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220614112228.1998-2-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-06-16 10:13:20 +02:00
Christian 'Ansuel' Marangi
9ec092d2fe net: ethernet: stmmac: add missing sgmii configure for ipq806x
The different gmacid require different configuration based on the soc
and on the gmac id. Add these missing configuration taken from the
original driver.

Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220614112228.1998-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-06-16 10:13:20 +02:00
David Thompson
cfbc80e34e mlxbf_gige: remove own module name define and use KBUILD_MODNAME instead
This patch adds use of KBUILD_MODNAME as defined by the build system,
replacing the definition and use of a custom-defined name.

Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Link: https://lore.kernel.org/r/20220614212602.28061-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-15 19:55:52 -07:00
Casper Andersson
fbb89d02e3 net: sparx5: Allow mdb entries to both CPU and ports
Allow mdb entries to be forwarded to CPU and be switched at the same
time. Only remove entry when no port and the CPU isn't part of the group
anymore.

Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 13:01:26 +01:00
Sieng Piaw Liew
c63c615e22 bcm63xx_enet: switch to napi_build_skb() to reuse skbuff_heads
napi_build_skb() reuses NAPI skbuff_head cache in order to save some
cycles on freeing/allocating skbuff_heads on every new Rx or completed
Tx.
Use napi_consume_skb() to feed the cache with skbuff_heads of completed
Tx so it's never empty.

Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 12:58:54 +01:00
Jose Alonso
36a15e1cb1 net: usb: ax88179_178a needs FLAG_SEND_ZLP
The extra byte inserted by usbnet.c when
 (length % dev->maxpacket == 0) is causing problems to device.

This patch sets FLAG_SEND_ZLP to avoid this.

Tested with: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet

Problems observed:
======================================================================
1) Using ssh/sshfs. The remote sshd daemon can abort with the message:
   "message authentication code incorrect"
   This happens because the tcp message sent is corrupted during the
   USB "Bulk out". The device calculate the tcp checksum and send a
   valid tcp message to the remote sshd. Then the encryption detects
   the error and aborts.
2) NETDEV WATCHDOG: ... (ax88179_178a): transmit queue 0 timed out
3) Stop normal work without any log message.
   The "Bulk in" continue receiving packets normally.
   The host sends "Bulk out" and the device responds with -ECONNRESET.
   (The netusb.c code tx_complete ignore -ECONNRESET)
Under normal conditions these errors take days to happen and in
intense usage take hours.

A test with ping gives packet loss, showing that something is wrong:
ping -4 -s 462 {destination}	# 462 = 512 - 42 - 8
Not all packets fail.
My guess is that the device tries to find another packet starting
at the extra byte and will fail or not depending on the next
bytes (old buffer content).
======================================================================

Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:32:12 +01:00
Lorenzo Bianconi
fe63ec97e3 i40e: add xdp frags support to ndo_xdp_xmit
Add the capability to map non-linear xdp frames in XDP_TX and ndo_xdp_xmit
callback.

Tested-by: Sarkar Tirthendu <tirthendu.sarkar@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:29:42 +01:00
Ivan Bornyakov
9794ef5a68 net: phy: marvell-88x2222: set proper phydev->port
phydev->port was not set and always reported as PORT_TP.
Set phydev->port according to inserted SFP module.

Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:25:31 +01:00
David S. Miller
371de1aa00 Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-06-14

This series contains updates to ice driver only.

Michal fixes incorrect Tx timestamp offset calculation for E822 devices.

Roman enforces required VLAN filtering settings for double VLAN mode.

Przemyslaw fixes memory corruption issues with VFs by ensuring
queues are disabled in the error path of VF queue configuration and to
disabled VFs during reset.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:15:33 +01:00
Alex Elder
c5bddecbb9 net: ipa: rework gsi_channel_tx_update()
Rename gsi_channel_tx_update() to be gsi_trans_tx_completed(), and
pass it just the transaction pointer, deriving the channel from the
transaction.  Update the comments above the function to provide a
more concise description of how statistics for TX endpoints are
maintained and used.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:07:58 +01:00
Alex Elder
dbad2fa719 net: ipa: stop counting total RX bytes and transactions
In gsi_evt_ring_rx_update(), we update each transaction so its len
field reflects the actual number of bytes received.  In the process,
the total number of transactions and bytes processed on the channel
are summed, and added to a running total for the channel.

But we don't actually use those running totals for RX endpoints.
They're maintained for TX channels to support CoDel when they are
associated with a "real" network device.

So stop maintaining these totals for RX endpoints, and update the
comment where the fields are defined to make it clear they're only
valid for TX channels.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:07:58 +01:00
Alex Elder
65d39497fa net: ipa: simplify TX completion statistics
When a TX request is issued, its channel's accumulated byte and
transaction counts are recorded.  This currently does *not* take
into account the transaction being committed.

Later, when the transaction completes, the number of bytes and
transactions that have completed since the transaction was committed
are reported to the network stack.  The transaction and its byte
count are accounted for at that time.

Instead, record the transaction and its bytes in the counts recorded
at commit time.  This avoids the need to do so when the transaction
completes, and provides a (small) simplification of that code.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:07:58 +01:00
Alex Elder
4e0f28e9ee net: ipa: introduce gsi_trans_tx_committed()
Create a new function that encapsulates recording information needed
for TX channel statistics when a transaction is committed.

Record the accumulated length in the transaction before the call
(for both RX and TX), so it can be used when updating TX statistics.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:07:58 +01:00
Alex Elder
3eeabea6c8 net: ipa: rename two transaction fields
There are two fields in a GSI transaction that keep track of TRE
counts.  The first represents the number of TREs reserved for the
transaction in the TRE ring; that's currently named "tre_count".
The second is the number of TREs that are actually *used* by the
transaction at the time it is committed.

Rename the "tre_count" field to be "rsvd_count", to make its meaning
a little more specific.  The "_count" is present in the name mainly
to avoid interpreting it as a reserved (not-to-be-used) field.  This
name also distinguishes it from the "tre_count" field associated
with a channel.

Rename the "used" field to be "used_count", to match the convention
used for reserved TREs.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:07:58 +01:00
Alex Elder
2295947bda net: ipa: use "tre_ring" for all TRE ring local variables
All local variables that represent event rings are named "ring".

All but two functions that represent a channel's TRE ring with a
local variable use the name "tre_ring".  For consistency, use that
name in the two functions that don't fit the pattern.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2022-06-15 09:07:58 +01:00
Frank Wunderlich
1f9a6abecf net: dsa: mt7530: get cpu-port via dp->cpu_dp instead of constant
Replace last occurences of hardcoded cpu-port by cpu_dp member of
dsa_port struct.

Now the constant can be dropped.

Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-14 22:35:16 -07:00
Frank Wunderlich
6e19bc26cc net: dsa: mt7530: rework mt753[01]_setup
Enumerate available cpu-ports instead of using hardcoded constant.

Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-14 22:35:16 -07:00