- fix the RTL8111DP turn off the power when DASH is enabled.
- RTL_GIGA_MAC_VER_27 must wait for tx finish before reset.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Adjust and remove certain settings of RTL8102E which are for previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
It results in the wrong point address and influences RTL8168DP.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).
Remember, that register DM9000_GPR was not changed by reset sequence.
Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: David S. Miller <davem@davemloft.net>
Max rx queues and tx queues are governed by fimware.
So driver should not validate these values.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove checks of 1 for auto_fw_reset module parameter.
auto_fw_reset is of type int and can have value > 1.
o Remove unnecessary #define for 1
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use discrete setting ops for not updated drivers. This will not make
them conform to full G/SFEATURES semantics, though.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement getting rx checksum state for not updated drivers.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid "Features changed" message and ndo_set_features call on device
registration caused by automatic enabling of GSO and GRO. Driver should
have enabled hardware offloads it set in features, so the ndo_set_features()
is not needed at registration time.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix netdev_update_features() messages on register time by moving
the call further in register_netdevice(). When
netdev->reg_state != NETREG_REGISTERED, netdev_name() returns
"(unregistered netdevice)" even if the dev's name is already filled.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code does not work well when the number of mulitcast
address to handle is greater than MCAST_MAX. It only enable promiscous
mode instead of multicast hash table mode, so the hash table function
will not be activated and all multicast frames will be recieved in this
condition.
This patch fixes the following issues with the r6040 NIC operating in
multicast:
1) When the IFF_ALLMULTI flag is set, we should write 0xffff to the NIC
hash table registers to make it process multicast traffic.
2) When the number of multicast address to handle is smaller than
MCAST_MAX, we should use the NIC multicast registers MID1_{L,M,H}.
3) The hashing of the address was not correct, due to an invalid
substraction (15 - (crc & 0x0f)) instead of (crc & 0x0f) and an
incorrect crc algorithm (ether_crc_le) instead of (ether_crc).
4) If necessary, we should set HASH_EN flag in MCR0 to enable multicast
hash table function.
Reported-by: Marc Leclerc <marc-leclerc@signaturealpha.com>
Tested-by: Marc Leclerc <marc-leclerc@signaturealpha.com>
Signed-off-by: Shawn Lin <shawn@dmp.com.tw>
Signed-off-by: Albert Chen <albert.chen@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pSR and pCR fields can be deleted with no changes in the functionality.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete dead code for skipping the video memory sizing.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due a cleanup in earlier patches, the function fbcon_XGI_sync now does nothing
so it has to be removed.
This patches removes the unused function.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xgifb framebuffer driver had an option to use an accelerator engine that never
got used (XGIfb_accel was always 0).
An earlier patchset removed the code relevant to the accelerator.
Since this spinlock was used only for that code, it can be deleted as well.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xgifb framebuffer driver has an option to use an accelerator engine that never
get used (XGIfb_accel is always 0).
An earlier patchset remove the code that depends on the accelerator being
activated. This patch removes all the references to XGIfb_accel.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xgifb staging driver for XG20, XG21, XG40, XG42 frame buffer device
has a accelerator engine that never get used (XGIfb_accel is always 0).
Also the driver has a set of defines that hides the synchronization
mechanism used to access critical sections and a way to disable spinlocks
use at compile time.
In a earlier patch all the code that depends on the accelerator being active
was deleted because it was dead code. Since the only usage of this
synchronization defines were in that dead code, this patch removes all the
now unused spinlock conditional compilation logic.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Earlier patch removed code that never got executed because it depended on
XGIfb_accel variable value to de distinct than 0. But this variable is
always 0 in current driver.
That dead code used a set of functions that not remains unused.
This patch removes these unused functions.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xgifb staging driver has code that dependens on XGIfb_accel != 0.
But as Dan Carpenter noticed, XGIfb_accel value is always 0 in current driver.
So there is code that never gets executed.
This patch removes this dead code.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
netem_skb_cb() does :
return (struct netem_skb_cb *)qdisc_skb_cb(skb)->data;
Unfortunatly struct qdisc_skb_cb data is not long word aligned, so
access to psched_time_t time_to_send uses a non aligned access.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use USB_SUBCLASS_AUDIOSTREAMING constant from usb/audio.h
instead of 0x02
Cc: Mike Thomas <rmthomas@sciolus.org>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mike Thomas <rmthomas@sciolus.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
make inputset population to be more compact and readable
Cc: Mike Thomas <rmthomas@sciolus.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix some code styles and drop too verbose printouts
and non relevant code
Cc: Mike Thomas <rmthomas@sciolus.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit f2f1794835.
It should not be putting code into the include/input/ directory, and
lots of other people have complained about it.
Cc: Tony SIM <chinyeow.sim.xt@renesas.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* make qdisc_ops local
* add sparse annotation about expected unlock/unlock in dump_class_stats
* fix indentation
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dmaw_block is an enum and max_pay_load is u32. Therefore
sparse gives warning about comparison of unsigned and signed value.
Resolve by using min_t to force cast.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use __force to quiet sparse warnings for cases where the code
is simulating user space pointers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing robustness of the code, although no problem has been reported
in the field. Several code paths were unshielded for multi thread access.
Several lock acquisitions have been added to wl_mac80211.c
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A spinlock was acquired prior to calling the Mac80211 functions
ieee80211_wake_queues() and ieee80211_stop_queues() and Cfg80211 functions
wiphy_rfkill_set_hw_state() and wiphy_rfkill_start_polling().
This is not required and could even lead to instability. Therefore the locks
were removed.
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Code cleanup. Added lock related comments to wl_mac80211.c. Also removed a
redundant function definition.
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the struct wlc_bsscfg a couple of attribute were held under a
preprocessor definition, but these are not needed in the mac80211
driver context.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When associated on 5G the driver receives a probe request for 2G with
a 2G rate specified. The driver asserts as the operating band is still
5G when the probe request packet is given. Root cause was that ioctl
function did fail upon setting the channel as requested by mac80211
when we are associated.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- move ltoh16_buf/htol16_buf util/bcmsrom.c
- replace ltoh16_buf in brcmsmac/wlc_mac80211.c with several
le16_to_cpu's
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tegra_dma_init currently simply bails out early if any initialization fails.
This skips various data-structure initialization. In turn, this means that
tegra_dma_allocate_channel can still hand out channels. In this case, when
tegra_dma_free_channel is called, which calls tegra_dma_cancel, the walking
on ch->list will OOPS since the list's next/prev pointers may still be
NULL.
To solve this, add an explicit "initialized" flag, only set this once _init
has fully completed successfully, and have _allocate_channel refuse to hand
out channels if this is not set.
While at it, simplify _init:
* Remove redundant memsets
* Use bitmap_fill to mark all channels as in-use up-front, and remove
some now-redundant bitmap initialization loops.
* Only mark a channel as free once all channel-related initialization has
completed.
Finally, the successful exit path from _init always has ret==0, so just
hard-code that return. The error path still returns ret.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>