Commit graph

112,392 commits

Author SHA1 Message Date
Horatiu Vultur
db8bcaad53 net: lan966x: add the basic lan966x driver
This patch adds basic SwitchDev driver framework for lan966x. It
includes only the IO range mapping and probing of the switch.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:58:38 +00:00
Linus Walleij
35aefaad32 net: ixp4xx_hss: Convert to use DT probing
IXP4xx is being migrated to device tree only. Convert this
driver to use device tree probing.

Pull in all the boardfile code from the one boardfile and
make it local, pull all the boardfile parameters from the
device tree instead of the board file.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:54:51 +00:00
Alvin Šipraga
ef136837aa net: dsa: rtl8365mb: set RGMII RX delay in steps of 0.3 ns
A contact at Realtek has clarified what exactly the units of RGMII RX
delay are. The answer is that the unit of RX delay is "about 0.3 ns".
Take this into account when parsing rx-internal-delay-ps by
approximating the closest step value. Delays of more than 2.1 ns are
rejected.

This obviously contradicts the previous assumption in the driver that a
step value of 4 was "about 2 ns", but Realtek also points out that it is
easy to find more than one RX delay step value which makes RGMII work.

Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Cc: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:51:37 +00:00
Alvin Šipraga
1ecab9370e net: dsa: rtl8365mb: fix garbled comment
Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:51:37 +00:00
Alvin Šipraga
b014861d96 net: dsa: realtek-smi: don't log an error on EPROBE_DEFER
Probe deferral is not an error, so don't log this as an error:

[0.590156] realtek-smi ethernet-switch: unable to register switch ret = -517

Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:51:37 +00:00
Stephan Gerhold
21a0ffd9b3 net: wwan: Add Qualcomm BAM-DMUX WWAN network driver
The BAM Data Multiplexer provides access to the network data channels of
modems integrated into many older Qualcomm SoCs, e.g. Qualcomm MSM8916 or
MSM8974. It is built using a simple protocol layer on top of a DMA engine
(Qualcomm BAM) and bidirectional interrupts to coordinate power control.

The modem announces a fixed set of channels by sending an OPEN command.
The driver exports each channel as separate network interface so that
a connection can be established via QMI from userspace. The network
interface can work either in Ethernet or Raw-IP mode (configurable via
QMI). However, Ethernet mode seems to be broken with most firmwares
(network packets are actually received as Raw-IP), therefore the driver
only supports Raw-IP mode.

Note that the control channel (QMI/AT) is entirely separate from
BAM-DMUX and is already supported by the RPMSG_WWAN_CTRL driver.

The driver uses runtime PM to coordinate power control with the modem.
TX/RX buffers are put in a kind of "ring queue" and submitted via
the bam_dma driver of the DMAEngine subsystem.

The basic architecture looks roughly like this:

                   +------------+                +-------+
         [IPv4/6]  |  BAM-DMUX  |                |       |
         [Data...] |            |                |       |
        ---------->|wwan0       | [DMUX chan: x] |       |
         [IPv4/6]  | (chan: 0)  | [IPv4/6]       |       |
         [Data...] |            | [Data...]      |       |
        ---------->|wwan1       |--------------->| Modem |
                   | (chan: 1)  |      BAM       |       |
         [IPv4/6]  | ...        |  (DMA Engine)  |       |
         [Data...] |            |                |       |
        ---------->|wwan7       |                |       |
                   | (chan: 7)  |                |       |
                   +------------+                +-------+

Note that some newer firmware versions support QMAP ("rmnet" driver)
as additional multiplexing layer on top of BAM-DMUX, but this is not
currently supported by this driver.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:27:34 +00:00
Sven Schuchmann
817b653160 net: usb: lan78xx: lan78xx_phy_init(): use PHY_POLL instead of "0" if no IRQ is available
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.

Fixes: cc89c323a3 ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:22:07 +00:00
Hao Chen
e54b708c54 net: hns3: use macro IANA_VXLAN_GPE_UDP_PORT to replace number 4790
This patch uses macro IANA_VXLAN_GPE_UDP_PORT to replace number 4790 for
cleanup.

Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:19:53 +00:00
Hao Chen
ed618bd809 net: vxlan: add macro definition for number of IANA VXLAN-GPE port
Add macro definition for number of IANA VXLAN-GPE port for generic use.

Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:19:53 +00:00
Luiz Angelo Daros de Luca
1e89ad864d net: dsa: realtek-smi: fix indirect reg access for ports>3
This switch family can have up to 8 UTP ports {0..7}. However,
INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK was using 2 bits instead of 3,
dropping the most significant bit during indirect register reads and
writes. Reading or writing ports 4, 5, 6, and 7 registers was actually
manipulating, respectively, ports 0, 1, 2, and 3 registers.

This is not sufficient but necessary to support any variant with more
than 4 UTP ports, like RTL8367S.

rtl8365mb_phy_{read,write} will now returns -EINVAL if phy is greater
than 7.

Fixes: 4af2950c50 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:14:31 +00:00
Vincent Whitchurch
f8e7dfd6fd net: stmmac: Avoid DMA_CHAN_CONTROL write if no Split Header support
The driver assumes that split headers can be enabled/disabled without
stopping/starting the device, so it writes DMA_CHAN_CONTROL from
stmmac_set_features().  However, on my system (IP v5.10a without Split
Header support), simply writing DMA_CHAN_CONTROL when DMA is running
(for example, with the commands below) leads to a TX watchdog timeout.

 host$ socat TCP-LISTEN:1024,fork,reuseaddr - &
 device$ ethtool -K eth0 tso off
 device$ ethtool -K eth0 tso on
 device$ dd if=/dev/zero bs=1M count=10 | socat - TCP4:host:1024
 <tx watchdog timeout>

Note that since my IP is configured without Split Header support, the
driver always just reads and writes the same value to the
DMA_CHAN_CONTROL register.

I don't have access to any platforms with Split Header support so I
don't know if these writes to the DMA_CHAN_CONTROL while DMA is running
actually work properly on such systems.  I could not find anything in
the databook that says that DMA_CHAN_CONTROL should not be written when
the DMA is running.

But on systems without Split Header support, there is in any case no
need to call enable_sph() in stmmac_set_features() at all since SPH can
never be toggled, so we can avoid the watchdog timeout there by skipping
this call.

Fixes: 8c6fc097a2 ("net: stmmac: gmac4+: Add Split Header support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:08:05 +00:00
Maxime Chevallier
2551dc9e39 net: mvneta: Add TC traffic shaping offload
The mvneta controller is able to do some tocken-bucket per-queue traffic
shaping. This commit adds support for setting these using the TC mqprio
interface.

The token-bucket parameters are customisable, but the current
implementation configures them to have a 10kbps resolution for the
rate limitation, since it allows to cover the whole range of max_rate
values from 10kbps to 5Gbps with 10kbps increments.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:05:52 +00:00
Maxime Chevallier
e9f7099d07 net: mvneta: Allow having more than one queue per TC
The current mqprio implementation assumed that we are only using one
queue per TC. Use the offset and count parameters to allow using
multiple queues per TC. In that case, the controller will use a standard
round-robin algorithm to pick queues assigned to the same TC, with the
same priority.

This only applies to VLAN priorities in ingress traffic, each TC
corresponding to a vlan priority.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:05:52 +00:00
Maxime Chevallier
e7ca75fe66 net: mvneta: Don't force-set the offloading flag
The qopt->hw flag is set by the TC code according to the offloading mode
asked by user. Don't force-set it in the driver, but instead read it to
make sure we do what's asked.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:05:52 +00:00
Maxime Chevallier
75fa71e3ac net: mvneta: Use struct tc_mqprio_qopt_offload for MQPrio configuration
The struct tc_mqprio_qopt_offload is a container for struct tc_mqprio_qopt,
that allows passing extra parameters, such as traffic shaping. This commit
converts the current mqprio code to that new struct.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:05:52 +00:00
Yang Yingliang
2f7ed29f2c net: mdio: ipq8064: replace ioremap() with devm_ioremap()
Use devm_ioremap() instead of ioremap() to avoid iounmap() missing.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-29 12:02:49 +00:00
Stanislaw Gruszka
ed53ae7569 rt2x00: do not mark device gone on EPROTO errors during start
As reported by Exuvo is possible that we have lot's of EPROTO errors
during device start i.e. firmware load. But after that device works
correctly. Hence marking device gone by few EPROTO errors done by
commit e383c70474 ("rt2x00: check number of EPROTO errors") caused
regression - Exuvo device stop working after kernel update. To fix
disable the check during device start.

Link: https://lore.kernel.org/linux-wireless/bff7d309-a816-6a75-51b6-5928ef4f7a8c@exuvo.se/
Reported-and-tested-by: Exuvo <exuvo@exuvo.se>
Fixes: e383c70474 ("rt2x00: check number of EPROTO errors")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111141003.GA134627@wp.pl
2021-11-29 12:53:50 +02:00
Kees Cook
69831173fc rtlwifi: rtl8192de: Style clean-ups
Clean up some style issues:
- Use ARRAY_SIZE() even though it's a u8 array.
- Remove redundant CHANNEL_MAX_NUMBER_2G define.
Additionally fix some dead code WARNs.

Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/lkml/57d0d1b6064342309f680f692192556c@realtek.com/
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119192233.1021063-1-keescook@chromium.org
2021-11-29 12:47:07 +02:00
Kees Cook
f01b377430 mwl8k: Use named struct for memcpy() region
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.

Use named struct in struct mwl8k_cmd_set_key around members key_material,
tkip_tx_mic_key, and tkip_rx_mic_key so they can be referenced
together. This will allow memcpy() and sizeof() to more easily reason
about sizes, improve readability, and avoid future warnings about writing
beyond the end of key_material.

"pahole" shows no size nor member offset changes to struct
mwl8k_cmd_set_key. "objdump -d" shows no object code changes.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119004905.2348143-1-keescook@chromium.org
2021-11-29 12:46:07 +02:00
Kees Cook
601d2293e2 intersil: Use struct_group() for memcpy() region
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.

Use struct_group() in struct hfa384x_tx_frame around members
frame_control, duration_id, addr1, addr2, addr3, and seq_ctrl, so they
can be referenced together. This will allow memcpy() and sizeof() to
more easily reason about sizes, improve readability, and avoid future
warnings about writing beyond the end of frame_control.

"pahole" shows no size nor member offset changes to struct
hfa384x_tx_frame. "objdump -d" shows no object code changes.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119004646.2347920-1-keescook@chromium.org
2021-11-29 12:45:17 +02:00
Kees Cook
642a57475b libertas_tf: Use struct_group() for memcpy() region
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field array bounds checking for memcpy(), memmove(), and memset(),
avoid intentionally writing across neighboring fields.

Use struct_group() in struct txpd around members tx_dest_addr_high
and tx_dest_addr_low so they can be referenced together. This will
allow memcpy() and sizeof() to more easily reason about sizes, improve
readability, and avoid future warnings about writing beyond the end
of tx_dest_addr_high.

"pahole" shows no size nor member offset changes to struct txpd.
"objdump -d" shows no object code changes.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118184121.1283821-1-keescook@chromium.org
2021-11-29 12:44:55 +02:00
Kees Cook
5fd32ae043 libertas: Use struct_group() for memcpy() region
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.

Use struct_group() in struct txpd around members tx_dest_addr_high
and tx_dest_addr_low so they can be referenced together. This will
allow memcpy() and sizeof() to more easily reason about sizes, improve
readability, and avoid future warnings about writing beyond the end
of queue_id.

"pahole" shows no size nor member offset changes to struct txpd.
"objdump -d" shows no object code changes.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118184104.1283637-1-keescook@chromium.org
2021-11-29 12:44:29 +02:00
Jason Wang
fa4408b079 wlcore: no need to initialise statics to false
Static variables do not need to be initialized to false. The
compiler will do that.

Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211113063551.257804-1-wangborong@cdjrlc.com
2021-11-29 12:44:10 +02:00
Zekun Shen
f1cb3476e4 rsi: Fix out-of-bounds read in rsi_read_pkt()
rsi_get_* functions rely on an offset variable from usb
input. The size of usb input is RSI_MAX_RX_USB_PKT_SIZE(3000),
while 2-byte offset can be up to 0xFFFF. Thus a large offset
can cause out-of-bounds read.

The patch adds a bound checking condition when rcv_pkt_len is 0,
indicating it's USB. It's unclear whether this is triggerable
from other type of bus. The following check might help in that case.
offset > rcv_pkt_len - FRAME_DESC_SZ

The bug is trigerrable with conpromised/malfunctioning USB devices.
I tested the patch with the crashing input and got no more bug report.

Attached is the KASAN report from fuzzing.

BUG: KASAN: slab-out-of-bounds in rsi_read_pkt+0x42e/0x500 [rsi_91x]
Read of size 2 at addr ffff888019439fdb by task RX-Thread/227

CPU: 0 PID: 227 Comm: RX-Thread Not tainted 5.6.0 #66
Call Trace:
 dump_stack+0x76/0xa0
 print_address_description.constprop.0+0x16/0x200
 ? rsi_read_pkt+0x42e/0x500 [rsi_91x]
 ? rsi_read_pkt+0x42e/0x500 [rsi_91x]
 __kasan_report.cold+0x37/0x7c
 ? rsi_read_pkt+0x42e/0x500 [rsi_91x]
 kasan_report+0xe/0x20
 rsi_read_pkt+0x42e/0x500 [rsi_91x]
 rsi_usb_rx_thread+0x1b1/0x2fc [rsi_usb]
 ? rsi_probe+0x16a0/0x16a0 [rsi_usb]
 ? _raw_spin_lock_irqsave+0x7b/0xd0
 ? _raw_spin_trylock_bh+0x120/0x120
 ? __wake_up_common+0x10b/0x520
 ? rsi_probe+0x16a0/0x16a0 [rsi_usb]
 kthread+0x2b5/0x3b0
 ? kthread_create_on_node+0xd0/0xd0
 ret_from_fork+0x22/0x40

Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxXS4wgu2OsmlVv@10-18-43-117.dynapool.wireless.nyu.edu
2021-11-29 12:43:54 +02:00
Zekun Shen
b07e3c6ebc rsi: Fix use-after-free in rsi_rx_done_handler()
When freeing rx_cb->rx_skb, the pointer is not set to NULL,
a later rsi_rx_done_handler call will try to read the freed
address.
This bug will very likley lead to double free, although
detected early as use-after-free bug.

The bug is triggerable with a compromised/malfunctional usb
device. After applying the patch, the same input no longer
triggers the use-after-free.

Attached is the kasan report from fuzzing.

BUG: KASAN: use-after-free in rsi_rx_done_handler+0x354/0x430 [rsi_usb]
Read of size 4 at addr ffff8880188e5930 by task modprobe/231
Call Trace:
 <IRQ>
 dump_stack+0x76/0xa0
 print_address_description.constprop.0+0x16/0x200
 ? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
 ? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
 __kasan_report.cold+0x37/0x7c
 ? dma_direct_unmap_page+0x90/0x110
 ? rsi_rx_done_handler+0x354/0x430 [rsi_usb]
 kasan_report+0xe/0x20
 rsi_rx_done_handler+0x354/0x430 [rsi_usb]
 __usb_hcd_giveback_urb+0x1e4/0x380
 usb_giveback_urb_bh+0x241/0x4f0
 ? __usb_hcd_giveback_urb+0x380/0x380
 ? apic_timer_interrupt+0xa/0x20
 tasklet_action_common.isra.0+0x135/0x330
 __do_softirq+0x18c/0x634
 ? handle_irq_event+0xcd/0x157
 ? handle_edge_irq+0x1eb/0x7b0
 irq_exit+0x114/0x140
 do_IRQ+0x91/0x1e0
 common_interrupt+0xf/0xf
 </IRQ>

Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXxQL/vIiYcZUu/j@10-18-43-117.dynapool.wireless.nyu.edu
2021-11-29 12:43:15 +02:00
Loic Poulain
7a6cfe28ae brcmfmac: Configure keep-alive packet on suspend
When entering suspend as a client station with wowlan enabled,
the Wi-Fi link is supposed to be maintained. In that state, no
more data is generated from client side, and the link stays idle
as long the station is suspended and as long the AP as no data to
transmit.

However, most of the APs kick-off such 'inactive' stations after
few minutes, causing unexpected disconnect (reconnect, etc...).

The usual way to prevent this is to submit a Null function frame
periodically as a keep-alive. This is something that can be host
/software generated (e.g. wpa_supplicant), but that needs to be
offloaded to the Wi-Fi controller in case of suspended host.

This change enables firmware generated keep-alive frames when
entering wowlan suspend, using the 'mkeep_alive' IOVAR.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637596046-21651-1-git-send-email-loic.poulain@linaro.org
2021-11-29 12:24:59 +02:00
Miri Korenblit
75c5bd68b6 ieee80211: change HE nominal packet padding value defines
It's easier to use and understand, and to extend for EHT later,
if we use the values here instead of the shifted values.

Unfortunately, we need to add _POS so that we can use it in
places like iwlwifi/mvm where constants are needed.

While at it, fix the typo ("NOMIMAL") which also helps catch any
conflicts.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/r/20211126104817.7c29a05b8eb5.I2ca9faf06e177e3035bec91e2ae53c2f91d41774@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-11-28 21:53:04 +01:00
Linus Torvalds
d06c942efe vhost,virtio,vdpa: bugfixes
Misc fixes all over the place.
 
 Revert of virtio used length validation series: the approach taken does
 not seem to work, breaking too many guests in the process. We'll need to
 do length validation using some other approach.
 
 Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
 -----BEGIN PGP SIGNATURE-----
 
 iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmGe0sEPHG1zdEByZWRo
 YXQuY29tAAoJECgfDbjSjVRp8WEH/imDIq1iduDeAuvFnmrm5eEO9w3wzXCT4NiG
 8Pla241FzQ1pEFEAne16KP0+SlLhj7P0oc5FR8vkYvxxuyneDbCzcS2M1kYMOpA1
 ry28PuObAnekzE/WXxvC031ozB5Zb/FL54gmw+/1EdAOdMGL0CdQ1aJxREBHRTBo
 p4ZHr83GA2D2C/IyKCsgQ8cB9ZrMqImTQQ4vRD89HoFBp+GH2u2Di1iyXEWuOqdI
 n1+7M9jjbyW8A+N1bkOicpShS/6UcyJQOOcg8kvUQOV6srVkYhfaiWC/CbOP2g73
 8PKK+/K2Htf92s6RdvDUPSKmvqGR/4KPZWPtWThXBYXGgWul0uI=
 =q6tO
 -----END PGP SIGNATURE-----

Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost

Pull vhost,virtio,vdpa bugfixes from Michael Tsirkin:
 "Misc fixes all over the place.

  Revert of virtio used length validation series: the approach taken
  does not seem to work, breaking too many guests in the process. We'll
  need to do length validation using some other approach"

[ This merge also ends up reverting commit f7a36b03a7 ("vsock/virtio:
  suppress used length validation"), which came in through the
  networking tree in the meantime, and was part of that whole used
  length validation series   - Linus ]

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vdpa_sim: avoid putting an uninitialized iova_domain
  vhost-vdpa: clean irqs before reseting vdpa device
  virtio-blk: modify the value type of num in virtio_queue_rq()
  vhost/vsock: cleanup removing `len` variable
  vhost/vsock: fix incorrect used length reported to the guest
  Revert "virtio_ring: validate used buffer length"
  Revert "virtio-net: don't let virtio core to validate used length"
  Revert "virtio-blk: don't let virtio core to validate used length"
  Revert "virtio-scsi: don't let virtio core to validate used buffer length"
2021-11-28 11:58:52 -08:00
Guenter Roeck
00169a9245 vmxnet3: Use generic Kconfig option for page size limit
Use the architecture independent Kconfig option PAGE_SIZE_LESS_THAN_64KB
to indicate that VMXNET3 requires a page size smaller than 64kB.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-27 14:34:41 -08:00
Jakub Kicinski
93d5404e89 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
drivers/net/ipa/ipa_main.c
  8afc7e471a ("net: ipa: separate disabling setup from modem stop")
  76b5fbcd6b ("net: ipa: kill ipa_modem_init()")

Duplicated include, drop one.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 13:45:19 -08:00
Oleksij Rempel
b3612ccdf2 net: dsa: microchip: implement multi-bridge support
Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:

	ip l a name br0 type bridge
	ip l a name br1 type bridge
	ip l s dev br0 up
	ip l s dev br1 up
	ip l s lan1 master br0
	ip l s dev lan1 up
	ip l s lan2 master br1
	ip l s dev lan2 up

	Ping on lan1 and get response on lan2, which should not happen.

This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.

This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.

Note: STP support was broken before this patch and should be fixed
separately.

Fixes: c2e866911e ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 12:46:38 -08:00
Vladimir Oltean
c49a35eedf net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.

Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:38:21 -08:00
Vladimir Oltean
96ca08c058 net: mscc: ocelot: set up traps for PTP packets
IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.

So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.

The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
    they arrive there via a trap and not via flooding

It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/

To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)

The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.

Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73
https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c

Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.

On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050
https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21

So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.

Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:38:21 -08:00
Vladimir Oltean
95706be13b net: mscc: ocelot: create a function that replaces an existing VCAP filter
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.

But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.

This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:38:20 -08:00
Vladimir Oltean
8a075464d1 net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".

According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.

Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:38:20 -08:00
Jie Wang
82229c4dbb net: hns3: fix incorrect components info of ethtool --reset command
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.

So fix this problem by clear corresponding reset flag after reset process.

Fixes: ddccc5e368 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:36:29 -08:00
Hao Chen
9c14791748 net: hns3: fix one incorrect value of page pool info when queried by debugfs
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.

So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.

Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:36:29 -08:00
Hao Chen
b8af344cfe net: hns3: add check NULL address for page pool
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.

Fixes: 850bfb912a ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:36:29 -08:00
Guangbin Huang
8d2ad993aa net: hns3: fix VF RSS failed problem after PF enable multi-TCs
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.

In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.

To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.

Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:36:29 -08:00
zhangyue
0435a4d080 net: qed: fix the array may be out of bound
If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.

The variable 'j' may be greater than or equal to 32.

At this time, the array 'p_aeu->bits[32]' may be out
of bound.

Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 11:29:20 -08:00
Yannick Vignon
b270bfe697 net: stmmac: Disable Tx queues when reconfiguring the interface
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)

Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.

Without this patch, the following kernel panic can be observed when doing
any of the actions above:

Unable to handle kernel paging request at virtual address ffff80001238d040
[....]
 Call trace:
  dwmac4_set_addr+0x8/0x10
  dev_hard_start_xmit+0xe4/0x1ac
  sch_direct_xmit+0xe8/0x39c
  __dev_queue_xmit+0x3ec/0xaf0
  dev_queue_xmit+0x14/0x20
[...]
[ end trace 0000000000000002 ]---

Fixes: 5fabb01207 ("net: stmmac: Add initial XDP support")
Fixes: aa042f60e4 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes: 0366f7e06a ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26 10:38:37 -08:00
Ajay Singh
d1e69b5492 wilc1000: remove '-Wunused-but-set-variable' warning in chip_wakeup()
Remove unused variables to avoid the below warnings:

   drivers/net/wireless/microchip/wilc1000/wlan.c: In function 'chip_wakeup':
>> drivers/net/wireless/microchip/wilc1000/wlan.c:620:34: warning: variable 'to_host_from_fw_bit' set but not used [-Wunused-but-set-variable]
     620 |         u32 to_host_from_fw_reg, to_host_from_fw_bit;
         |                                  ^~~~~~~~~~~~~~~~~~~
>> drivers/net/wireless/microchip/wilc1000/wlan.c:620:13: warning: variable 'to_host_from_fw_reg' set but not used [-Wunused-but-set-variable]
     620 |         u32 to_host_from_fw_reg, to_host_from_fw_bit;
         |             ^~~~~~~~~~~~~~~~~~~

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115102809.1408267-1-ajay.kathat@microchip.com
2021-11-26 18:32:51 +02:00
Emmanuel Grumbach
7ce1f2157e iwlwifi: mvm: read the rfkill state and feed it to iwlmei
Read the rfkill state upon boot, mac start and mac stop.

Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-6-emmanuel.grumbach@intel.com
2021-11-26 18:31:48 +02:00
Emmanuel Grumbach
bfcfdb59b6 iwlwifi: mvm: add vendor commands needed for iwlmei
Add the vendor commands that must be used by the network manager
to allow proper operation of iwlmei.

* Send information on the AP CSME is connected to
* Notify the userspace when roaming is forbidden
* Allow the userspace to require ownership

Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

v6: remove the VENDOR_CMDS Kconfig option and make the whole infra
    depend on IWLMEI directly
v7: remove // comments
    remove an unneeded function
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-5-emmanuel.grumbach@intel.com
2021-11-26 18:31:48 +02:00
Emmanuel Grumbach
6d19a5eba5 iwlwifi: integrate with iwlmei
iwlmei needs to know about the follwing events:

* Association
* De-association
* Country Code change
* SW Rfkill change
* SAR table changes

iwlmei can take the device away from us, so report the new
rfkill type when this happens.
Advertise the required data from the CSME firmware to the
usersapce: mostly, the AP that the CSME firmware is currently
associated to in case there is an active link protection
session.
Generate the HOST_ASSOC / HOST_DISSASSOC messages.

Don't support WPA1 (non-RSNA) for now.
Don't support shared wep either.
We can then determine the AUTH parameter by checking the AKM.
Feed the cipher from the key installation.

SW Rfkill will be implemented later when cfg80211 will
allow us to read the SW Rfkill state.

Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

v7: Ayala added her signed-off
    remove pointless function declaration
    fix a bug due to merge conflict in the HOST_ASSOC message
v8: leave a print if we have a SAP connection on a device we do
    not support (yet)
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-4-emmanuel.grumbach@intel.com
2021-11-26 18:31:48 +02:00
Emmanuel Grumbach
4ea7da5fad iwlwifi: mei: add debugfs hooks
Add three debugfs hooks:
* status: Check if we have a connection with the CSME
  firwmare. This hook is a read only.

* req_ownership: Send a SAP command to request ownership. This
  flow should be triggered by iwlwifi (from user space through
  vendor commands really), but being able to trigger an ownership
  request from debugfs allows us to request ownership without
  connecting afterwards. This is an "error" flow that the CSME
  firmware is designed to handle this way:
  + Grant ownership since the host asked for it
  + Wait 3 seconds to let the host connect
  + If the host didn't connect, take the device back (forcefully).
  + Don't grant any new ownership request in the following 30
  seconds.
  This debugfs hook allows us to test this flow.

* send_start_message: Restart the communication with the CSME
  firmware from the very beginning. At the very beginning (upon
  iwlwifi start), iwlmei send a special message: SAP_ME_MSG_START.
  This hook allows to send it again and this will retrigger the
  whole flow. It is important to test this restart in the middle
  of normal operation since it can happen (in case the CSME
  firmware decided to reset for example).

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-3-emmanuel.grumbach@intel.com
2021-11-26 18:31:47 +02:00
Emmanuel Grumbach
2da4366f9e iwlwifi: mei: add the driver to allow cooperation with CSME
CSME in two words
-----------------
CSME stands for Converged Security and Management Engine. It is
a CPU on the chipset and runs a dedicated firmware.
AMT (Active Management Technology) is one of the applications
that run on that CPU. AMT allows to control the platform remotely.
Here is a partial list of the use cases:
* View the screen of the plaform, with keyboard and mouse (KVM)
* Attach a remote IDE device
* Have a serial console to the device
* Query the state of the platform
* Reset / shut down / boot the platform

Networking in CSME
------------------
For those uses cases, CSME's firmware has an embedded network
stack and is able to use the network devices of the system: LAN
and WLAN. This is thanks to the CSME's firmware WLAN driver.

One can add a profile (SSID / key / certificate) to the CSME's OS
and CSME will connect to that profile. Then, one can use the WLAN
link to access the applications that run on CSME (AMT is one of
them). Note that CSME is active during power state and power state
transitions. For example, it is possible to have a KVM session
open to the system while the system is rebooting and actually
configure the BIOS remotely over WLAN thanks to AMT.

How all this is related to Linux
--------------------------------
In Linux, there is a driver that allows the OS to talk to the
CSME firmware, this driver is drivers/misc/mei. This driver
advertises a bus that allows other kernel drivers or even user
space) to talk to components inside the CSME firmware.
In practice, the system advertises a PCI device that allows
to send / receive data to / from the CSME firmware. The mei
bus drivers in drivers/misc/mei is an abstration on top of
this PCI device.
The driver being added here is called iwlmei and talks to the
WLAN driver inside the CSME firmware through the mei bus driver.
Note that the mei bus driver only gives bus services, it doesn't
define the content of the communication.

Why do we need this driver?
--------------------------
CSME uses the same WLAN device that the OS is expecting to see
hence we need an arbitration mechanism. This is what iwlmei is
in charge of. iwlmei maintains the communication with the CSME
firmware's WLAN driver. The language / protocol that is used
between the CSME's firmware WLAN driver and iwlmei is OS agnostic
and is called SAP which stands for Software Abritration Protocol.
With SAP, iwlmei will be able to tell the CSME firmware's WLAN
driver:
1) Please give me the device.
2) Please note that the SW/HW rfkill state change.
3) Please note that I am now associated to X.
4) Please note that I received this packet.
etc...

There are messages that go the opposite direction as well:
1) Please note that AMT is en/disable.
2) Please note that I believe the OS is broken and hence I'll take
   the device *now*, whether you like it or not, to make sure that
   connectivity is preserved.
3) Please note that I am willing to give the device if the OS
   needs it.
4) Please give me any packet that is sent on UDP / TCP on IP address
   XX.XX.XX.XX and an port ZZ.
5) Please send this packet.
etc...

Please check drivers/net/wireless/intel/iwlwifi/mei/sap.h for the
full protocol specification.

Arbitration is not the only purpose of iwlmei and SAP. SAP also
allows to maintain the AMT's functionality even when the OS owns
the device. To connect to AMT, one needs to initiate an HTTP
connection to port 16992. iwlmei will listen to the Rx path and
forward (through SAP) to the CSME firmware the data it got. Then,
the embedded HTTP server in the chipset will reply to the request
and send a SAP notification to ask iwlmei to send the reply.
This way, AMT running on the CSME can still work.

In practice this means that all the use cases quoted above (KVM,
remote IDE device, etc...) will work even when the OS uses the
WLAN device.

How to disable all this?
---------------------------
iwlmei won't be able to do anything if the CSME's networking stack
is not enabled. By default, CSME's networking stack is disabled (this
is a BIOS setting).
In case the CSME's networking stack is disabled, iwlwifi will just
get access to the device because there is no contention with any other
actor and, hence, no arbitration is needed.

In this patch, I only add the iwlmei driver. Integration with
iwlwifi will be implemented in the next one.

Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

v2: fix a few warnings raised by the different bots
v3: rewrite the commit message
v4: put the debugfs content in a different patch
v5: fix a NULL pointer dereference upon DHCP TX if SAP is connected
    since we now have the required cfg80211 bits in wl-drv-next, add
    the RFKILL handling patch to this series.
v6: change the SAP API to inherit the values from iwl-mei.h removing
    the need to ensure the values are equal with a BUILD_BUG_ON.
    This was suggested by Arend
v7: * fix a locking issue in case of CSME firmware reset:
      When the CSME firmware resets, we need to unregister the
      netdev, first take the mutex, and only then, rely on it
      being taken.
    * Add a comment to explain why it is ok to have static variables
      (iwlmei can't have more than a single instance).
    * Add a define for 26 + 8 + 8
    * Add a define SEND_SAP_MAX_WAIT_ITERATION
    * make struct const
    * Reword a bit the Kconfig help message
    * Ayala added her Signed-off
    * fixed an RCU annotation
v8: do not require ownership upfront, use NIC_OWNER instead. This fixes
    a deadlock when CSME does not have the right WiFi FW.
    Add more documentation about the owernship transition
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-2-emmanuel.grumbach@intel.com
2021-11-26 18:31:47 +02:00
Jonas Dreßler
84d94e16ef mwifiex: Ignore BTCOEX events from the 88W8897 firmware
The firmware of the 88W8897 PCIe+USB card sends those events very
unreliably, sometimes bluetooth together with 2.4ghz-wifi is used and no
COEX event comes in, and sometimes bluetooth is disabled but the
coexistance mode doesn't get disabled.

This means we sometimes end up capping the rx/tx window size while
bluetooth is not enabled anymore, artifically limiting wifi speeds even
though bluetooth is not being used.

Since we can't fix the firmware, let's just ignore those events on the
88W8897 device. From some Wireshark capture sessions it seems that the
Windows driver also doesn't change the rx/tx window sizes when bluetooth
gets enabled or disabled, so this is fairly consistent with the Windows
driver.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103205827.14559-1-verdre@v0yd.nl
2021-11-26 18:30:13 +02:00
Jonas Dreßler
deb573f1d7 mwifiex: Ensure the version string from the firmware is 0-terminated
We assume at a few places that priv->version_str is 0-terminated, but
right now we trust the firmware that this is the case with the version
string we get from it.

Let's rather ensure this ourselves and replace the last character with
'\0'.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-4-verdre@v0yd.nl
2021-11-26 18:29:38 +02:00
Jonas Dreßler
939b571a3b mwifiex: Add quirk to disable deep sleep with certain hardware revision
The 88W8897 PCIe+USB card in the hardware revision 20 apparently has a
hardware issue where the card wakes up from deep sleep randomly and very
often, somewhat depending on the card activity, maybe the hardware has a
floating wakeup pin or something. This was found by comparing two MS
Surface Book 2 devices, where one devices wifi card experienced spurious
wakeups, while the other one didn't.

Those continuous wakeups prevent the card from entering host sleep when
the computer suspends. And because the host won't answer to events from
the card anymore while it's suspended, the firmwares internal power
saving state machine seems to get confused and the card can't sleep
anymore at all after that.

Since we can't work around that hardware bug in the firmware, let's
get the hardware revision string from the firmware and match it with
known bad revisions. Then disable auto deep sleep for those revisions,
which makes sure we no longer get those spurious wakeups.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103201800.13531-3-verdre@v0yd.nl
2021-11-26 18:29:38 +02:00