If netif is running when stmmac_dvr_remove is invoked,
the unregister_netdev will call ndo_stop(stmmac_release) and
vlan_kill_rx_filter(stmmac_vlan_rx_kill_vid).
Currently, stmmac_dvr_remove() will disable pm runtime before
unregister_netdev. When stmmac_vlan_rx_kill_vid is invoked,
pm_runtime_resume_and_get in it returns EACCESS error number,
and reports:
dwmac-mediatek 11021000.ethernet eth0: stmmac_dvr_remove: removing driver
dwmac-mediatek 11021000.ethernet eth0: FPE workqueue stop
dwmac-mediatek 11021000.ethernet eth0: failed to kill vid 0081/0
Move the pm_runtime_disable to the end of stmmac_dvr_remove
to fix this issue.
Fixes: 6449520391 ("net: stmmac: properly handle with runtime pm in stmmac_dvr_remove()")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pm_runtime takes care of the clock handling in current
stmmac drivers, and dwmac-mediatek implement the
mediatek_dwmac_clks_config() as the callback for pm_runtime.
Then, stripping duplicated clocks handling in old init()/exit()
to fix clock issue in suspend/resume test.
As to clocks in probe/remove, vendor need symmetric handling to
ensure clocks balance.
Test pass, including suspend/resume and ko insertion/remove.
Fixes: 3186bdad97 ("stmmac: dwmac-mediatek: add platform level clocks management")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When number of LMACs active on a CGX/RPM are 3, then
current NIX link credit config based on per lmac fifo
length which inturn is calculated as
'lmac_fifo_len = total_fifo_len / 3', is incorrect. In HW
one of the LMAC gets half of the FIFO and rest gets 1/4th.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k driver to qca dir in preparation for code split and
introduction of ipq4019 switch based on qca8k.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_fwd_update_priority, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 432e05d328 ("net: ipv4: Control SKB reprioritization after forwarding")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_ip_default_ttl, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a pointer to the TX STA even when it's
not authenticated/... yet, fix the TX link selection in
hwsim to select only among the valid links for the STA,
requiring a STA pointer here. Also implement a simple
round-robin between links to make life more interesting.
While at it, also consider A3 when translating to link
addresses.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the link ID provided in TX frame metadata to select the correct
channel. For now, always select the link with the lowest link ID and
do some address translation.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make mac80211_hwsim_sta_rc_update() iterate over all the STA links.
This is somewhat temporary, we really should add the link to the
API, but then hwsim still calls it internally and would need this.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, we need to transmit to another MLD and select
the link to it, which requires knowing the station.
But in TX, mac80211 will not give us a station that's
not added to the driver, which in the older add/remove
API is only done later.
Implement the new API in MLO so we know about the STA
at all times and get a pointer during TX as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since struct ieee80211_bss_conf already contains link_id,
passing link_id is not necessary.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align the mac80211 implementation with P802.11be_D2.0.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do address matching with link addresses as well.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the link_station_parameters structure in the station_parameters
structure (and remove the station_parameters fields already existing
in link_station_parameters).
Now, for an MLD station, the default link is added together with
the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Accept frames from all the links' channels.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We won't really have enough skbs to need a 64-bit cookie,
and on 32-bit platforms storing the 64-bit cookie into the
void *rate_driver_data doesn't work anyway. Switch back to
using just a 32-bit cookie and uintptr_t for the type to
avoid compiler warnings about all this.
Fixes: 4ee186fa7e ("wifi: mac80211_hwsim: fix race condition in pending packet")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove a variable here that was now set but never used.
Fixes: f276e20b18 ("wifi: mac80211: move interface config to new struct")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) Support 802.1ad for bridge offloads
Vlad Buslov Says:
=================
Current mlx5 bridge VLAN offload implementation only supports 802.1Q VLAN
Ethernet protocol. That protocol type is assumed by default and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification is ignored.
In order to support dynamically setting VLAN protocol handle
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification by flushing FDB and
re-creating VLAN modify header actions with a new protocol. Implement support
for 802.1ad protocol by saving the current VLAN protocol to per-bridge variable
and re-create the necessary flow groups according to its current value (either
use cvlan or svlan flow fields).
==================
2) debugfs to count ongoing FW commands
3) debugfs to query eswitch vport firmware diagnostic counters
4) Add missing meter configuration in flow action
5) Some misc cleanup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmLPTbEACgkQSD+KveBX
+j5sfwf+N5Ij3SI+jbUr+xZXGovTkBGf1mcTU692bxim9I3W3gbiOE1gHFwgiYkC
/YX4/XjDwAX+AWWQOd+IHfOADc/xSro5lYScLxpKaAR1Q616bFtp5hsETiibLSay
PJdpqWLG3vznayx9dLBcH06M+yG27nxqShsPUfunJLrKy8HbH0pLlndYuJHFi0mx
Z6ujqKT0zKxWiTqVMhTcTjYLOLXxs8iRqJYGuWDaXckvL8C0hPEl4NnTGd9LHNiH
pRwuTQwLzU29uT/Zvpyq9cDkA7sk/zqP1IqvkyiF0UQf3UqF0OLp2s/4s3aMOoz5
rzFVxi/c8o049VZc7e6NdXav3AL0Xw==
=Kb8D
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2022-07-13
1) Support 802.1ad for bridge offloads
Vlad Buslov Says:
=================
Current mlx5 bridge VLAN offload implementation only supports 802.1Q VLAN
Ethernet protocol. That protocol type is assumed by default and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification is ignored.
In order to support dynamically setting VLAN protocol handle
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification by flushing FDB and
re-creating VLAN modify header actions with a new protocol. Implement support
for 802.1ad protocol by saving the current VLAN protocol to per-bridge variable
and re-create the necessary flow groups according to its current value (either
use cvlan or svlan flow fields).
==================
2) debugfs to count ongoing FW commands
3) debugfs to query eswitch vport firmware diagnostic counters
4) Add missing meter configuration in flow action
5) Some misc cleanup
* tag 'mlx5-updates-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Remove the duplicating check for striding RQ when enabling LRO
net/mlx5e: Move the LRO-XSK check to mlx5e_fix_features
net/mlx5e: Extend flower police validation
net/mlx5e: configure meter in flow action
net/mlx5e: Removed useless code in function
net/mlx5: Bridge, implement QinQ support
net/mlx5: Bridge, implement infrastructure for VLAN protocol change
net/mlx5: Bridge, extract VLAN push/pop actions creation
net/mlx5: Bridge, rename filter fg to vlan_filter
net/mlx5: Bridge, refactor groups sizes and indices
net/mlx5: debugfs, Add num of in-use FW command interface slots
net/mlx5: Expose vnic diagnostic counters for eswitch managed vports
net/mlx5: Use software VHCA id when it's supported
net/mlx5: Introduce ifc bits for using software vhca id
net/mlx5: Use the bitmap API to allocate bitmaps
====================
Link: https://lore.kernel.org/r/20220713225859.401241-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return value is not used, so change the return value type to void.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nfp_tun_write_neigh() function will configure a tunnel neighbour when
calling nfp_tun_neigh_event_handler() or nfp_flower_cmsg_process_one_rx()
(with no tunnel neighbour type) from firmware.
When configuring IP on physical port as a tunnel endpoint, no operation
will be performed after receiving the cmsg mentioned above.
Therefore, add a progress to configure tunnel neighbour in this case.
v2: Correct format of fixes tag.
Fixes: f1df7956c1 ("nfp: flower: rework tunnel neighbour configuration")
Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220714081915.148378-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The initially merged version of the igc driver code (via commit
146740f9ab, "igc: Add support for PF") contained the following
IGC_REMOVED checks in the igc_rd32/wr32() MMIO accessors:
u32 igc_rd32(struct igc_hw *hw, u32 reg)
{
u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr);
u32 value = 0;
if (IGC_REMOVED(hw_addr))
return ~value;
value = readl(&hw_addr[reg]);
/* reads should not return all F's */
if (!(~value) && (!reg || !(~readl(hw_addr))))
hw->hw_addr = NULL;
return value;
}
And:
#define wr32(reg, val) \
do { \
u8 __iomem *hw_addr = READ_ONCE((hw)->hw_addr); \
if (!IGC_REMOVED(hw_addr)) \
writel((val), &hw_addr[(reg)]); \
} while (0)
E.g. igb has similar checks in its MMIO accessors, and has a similar
macro E1000_REMOVED, which is implemented as follows:
#define E1000_REMOVED(h) unlikely(!(h))
These checks serve to detect and take note of an 0xffffffff MMIO read
return from the device, which can be caused by a PCIe link flap or some
other kind of PCI bus error, and to avoid performing MMIO reads and
writes from that point onwards.
However, the IGC_REMOVED macro was not originally implemented:
#ifndef IGC_REMOVED
#define IGC_REMOVED(a) (0)
#endif /* IGC_REMOVED */
This led to the IGC_REMOVED logic to be removed entirely in a
subsequent commit (commit 3c215fb18e, "igc: remove IGC_REMOVED
function"), with the rationale that such checks matter only for
virtualization and that igc does not support virtualization -- but a
PCIe device can become detached even without virtualization being in
use, and without proper checks, a PCIe bus error affecting an igc
adapter will lead to various NULL pointer dereferences, as the first
access after the error will set hw->hw_addr to NULL, and subsequent
accesses will blindly dereference this now-NULL pointer.
This patch reinstates the IGC_REMOVED checks in igc_rd32/wr32(), and
implements IGC_REMOVED the way it is done for igb, by checking for the
unlikely() case of hw_addr being NULL. This change prevents the oopses
seen when a PCIe link flap occurs on an igc adapter.
Fixes: 146740f9ab ("igc: Add support for PF")
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit 1866aa0d0d.
Commit 1866aa0d0d ("e1000e: Fix possible HW unit hang after an s0ix
exit") was a workaround for CSME problem to handle messages comes via H2ME
mailbox. This problem has been fixed by patch "e1000e: Enable the GPT
clock before sending message to the CSME".
Fixes: 3e55d23171 ("e1000e: Add handshake with the CSME to support S0ix")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214821
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On corporate (CSME) ADL systems, the Ethernet Controller may stop working
("HW unit hang") after exiting from the s0ix state. The reason is that
CSME misses the message sent by the host. Enabling the dynamic GPT clock
solves this problem. This clock is cleared upon HW initialization.
Fixes: 3e55d23171 ("e1000e: Add handshake with the CSME to support S0ix")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214821
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Below commit claims that atlantic NIC requires to reset the device on pm
op, and had set the deep to true for all suspend/resume functions.
commit 1809c30b6e ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
So, we could remove deep parameter on suspend/resume functions without
any functional change.
Fixes: 1809c30b6e ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Link: https://lore.kernel.org/r/20220713111224.1535938-1-acelan.kao@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When creating VFs a kernel panic can happen when calling to
efx_ef10_try_update_nic_stats_vf.
When releasing a DMA coherent buffer, sometimes, I don't know in what
specific circumstances, it has to unmap memory with vunmap. It is
disallowed to do that in IRQ context or with BH disabled. Otherwise, we
hit this line in vunmap, causing the crash:
BUG_ON(in_interrupt());
This patch reenables BH to release the buffer.
Log messages when the bug is hit:
kernel BUG at mm/vmalloc.c:2727!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 6 PID: 1462 Comm: NetworkManager Kdump: loaded Tainted: G I --------- --- 5.14.0-119.el9.x86_64 #1
Hardware name: Dell Inc. PowerEdge R740/06WXJT, BIOS 2.8.2 08/27/2020
RIP: 0010:vunmap+0x2e/0x30
...skip...
Call Trace:
__iommu_dma_free+0x96/0x100
efx_nic_free_buffer+0x2b/0x40 [sfc]
efx_ef10_try_update_nic_stats_vf+0x14a/0x1c0 [sfc]
efx_ef10_update_stats_vf+0x18/0x40 [sfc]
efx_start_all+0x15e/0x1d0 [sfc]
efx_net_open+0x5a/0xe0 [sfc]
__dev_open+0xe7/0x1a0
__dev_change_flags+0x1d7/0x240
dev_change_flags+0x21/0x60
...skip...
Fixes: d778819609 ("sfc: DMA the VF stats only when requested")
Reported-by: Ma Yuying <yuma@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220713092116.21238-1-ihuguet@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Check the retrieved grant reference first; there's no point trying to
have xennet_move_rx_slot() move invalid data (and further defer
recognition of the issue, likely making diagnosis yet more difficult).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In talk_to_netback(), called earlier from xennet_connect(), queues and
shared rings were just re-initialized, so all this function call could
result in is setting ->broken (again) right away in case any unconsumed
responses were found.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Set the maximum time firmware should poll for a link.
If not set firmware could block CPU for a long time resulting
in mailbox failures. If link doesn't come up within 1second,
firmware will anyway notify the status as and when LINK comes up
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20220712161815.12621-1-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-07-12
This series contains updates to ice driver only.
Paul fixes detection of E822 devices for firmware update and changes NVM
read for snapshot creation to be done in chunks as some systems cannot
read the entire NVM in the allotted time.
====================
Link: https://lore.kernel.org/r/20220712164829.7275-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use after free is detected by kfence when disabling sriov. What was read
after being freed was vf->pci_dev: it was freed from pci_disable_sriov
and later read in efx_ef10_sriov_free_vf_vports, called from
efx_ef10_sriov_free_vf_vswitching.
Set the pointer to NULL at release time to not trying to read it later.
Reproducer and dmesg log (note that kfence doesn't detect it every time):
$ echo 1 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
$ echo 0 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
BUG: KFENCE: use-after-free read in efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
Use-after-free read at 0x00000000ff3c1ba5 (in kfence-#224):
efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
efx_ef10_pci_sriov_disable+0x38/0x70 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xfe/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
kfence-#224: 0x00000000edb8ef95-0x00000000671f5ce1, size=2792, cache=kmalloc-4k
allocated by task 6771 on cpu 10 at 3137.860196s:
pci_alloc_dev+0x21/0x60
pci_iov_add_virtfn+0x2a2/0x320
sriov_enable+0x212/0x3e0
efx_ef10_sriov_configure+0x67/0x80 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xba/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
freed by task 6771 on cpu 12 at 3170.991309s:
device_release+0x34/0x90
kobject_cleanup+0x3a/0x130
pci_iov_remove_virtfn+0xd9/0x120
sriov_disable+0x30/0xe0
efx_ef10_pci_sriov_disable+0x57/0x70 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xfe/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 3c5eb87605 ("sfc: create vports for VFs and assign random MAC addresses")
Reported-by: Yanghang Liu <yanghliu@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220712062642.6915-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LRO requires striding RQ and checks that it's enabled at two places:
mlx5e_fix_features and set_feature_lro. This commit keeps only one check
at mlx5e_fix_features and removes the duplicating one in
set_feature_lro.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
LRO is mutually exclusive with XSK. When LRO is enabled, it checks
whether XSK is active. This commit moves this check to a more correct
place at mlx5e_fix_features.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Recent net commit 4d1e07d83c ("net/mlx5e: Fix matchall police parameters
validation") removed notexceed action id validation from
mlx5e_police_validate() and left it up to callers. However, since
tc_act_can_offload_police() only exists in net-next its validation is
extended in this dedicated followup patch.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
After police action is parsed, set meter data in flow action,
so they can be used when adding FTE.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Comparison of eth_ft->ft with NULL is useless, because
get_flow_table() returns either pointer 'eth_ft'
such that eth_ft->ft != NULL, or an erroneous value that is
handled on return, causing mlx5e_ethtool_flow_replace()
to terminate before checking whether eth_ft->ft equals NULL.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Implement support for new 802.1ad VLAN protocol type. Create new flow
groups that handle svlan tags. Create FDB flows with svlan tag match when
bridge VLAN is set to QinQ.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Current implementation only supports 802.1Q VLAN Ethernet protocol. That
protocol type is assumed by default and
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification is ignored. To prepare
for supporting 802.1ad protocol in following patches implement the
necessary infrastructure to allow the user to dynamically change the VLAN
protocol:
- Handle SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL notification by flushing
FDB and re-creating VLAN modify header actions with new protocol. In this
patch the only allowed dynamic VLAN protocol value is ETH_P_8021Q.
- Save current VLAN protocol in per-bridge instance variable. Use the
dynamic variable instead of hardcoded values in mlx5 bridge code. Create
VLAN flow groups and flows based on current mlx5_esw_bridge->vlan_proto
value instead of assuming 802.1Q ethertype.
- Extract common flow group creation code into dedicated functions in order
to be reused for creating QinQ groups in following patches.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in series need to re-create VLAN actions when user
changes VLAN protocol. Extract the code that creates VLAN push/pop actions
into dedicated function in order to be reused in next patch.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in series introduce new qinq filtering group. To improve
readability rename the existing group in function, variable and definition
names to include "vlan" in order to make it easy to distinguish from
upcoming qinq group.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in the series introduce additional flow groups for QinQ
support. With increased number of groups it becomes cumbersome to calculate
groups sizes as fractions of the table size. Instead, manually define sizes
of specific group types and ensure that totals are still correct by static
assertions. Having specific table size is important for firmware resource
management.
This commit doesn't change functionality.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Expose the number of busy / in-use slots in the FW command interface via
a read-only debugfs entry. This improves observability and helps in the
performance bottleneck analysis.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>