Physical continuity is not necessary, and requested allocation size might
be larger than PAGE_SIZE.
Hence, use v-alloc/free API.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Take the wrapper version which picks default node into a header file.
This reduces the number of exported functions.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add syndrome of last command failure per command type to debugfs to ease
debugging of such failure.
last_failed_syndrome - last command failed syndrome returned by FW.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In case fw sync reset is called in parallel to device removal, device
might stuck in the following deadlock:
CPU 0 CPU 1
----- -----
remove_one
uninit_one (locks intf_state_mutex)
mlx5_sync_reset_now_event()
work in fw_reset->wq.
mlx5_enter_error_state()
mutex_lock (intf_state_mutex)
cleanup_once
fw_reset_cleanup()
destroy_workqueue(fw_reset->wq)
Drain the fw_reset WQ, and make sure no new work is being queued, before
entering uninit_one().
The Drain is done before devlink_unregister() since fw_reset, in some
flows, is using devlink API devlink_remote_reload_actions_performed().
Fixes: 38b9f903f2 ("net/mlx5: Handle sync reset request event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Cited patch sets flow_source to ANY overriding the provided spec
flow_source, avoiding the optimization done by commit c9c079b4de
("net/mlx5: CT: Set flow source hint from provided tuple device").
To fix the above, set the dr_rule flow_source from provided flow spec.
Fixes: 3ee61ebb0d ("net/mlx5: CT: Add software steering ct flow steering provider")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
cited commit removed support for GRE tuples when software steering was enabled.
To bring back support for GRE tuples, add GRE ipv4/ipv6 matchers.
Fixes: 3ee61ebb0d ("net/mlx5: CT: Add software steering ct flow steering provider")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
We got reports of certain HW-GRO flows causing kernel call traces, which
might be related to firmware. To be on the safe side, disable the
feature for now and re-enable it once a driver/firmware fix is found.
Fixes: 83439f3c37 ("net/mlx5e: Add HW-GRO offload")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
HW GRO is incompatible and mutually exclusive with XDP and XSK. However,
the needed checks are only made when enabling XDP. If HW GRO is enabled
when XDP is already active, the command will succeed, and XDP will be
skipped in the data path, although still enabled.
This commit fixes the bug by checking the XDP and XSK status in
mlx5e_fix_features and disabling HW GRO if XDP is enabled.
Fixes: 83439f3c37 ("net/mlx5e: Add HW-GRO offload")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
LRO is incompatible and mutually exclusive with XDP. However, the needed
checks are only made when enabling XDP. If LRO is enabled when XDP is
already active, the command will succeed, and XDP will be skipped in the
data path, although still enabled.
This commit fixes the bug by checking the XDP status in
mlx5e_fix_features and disabling LRO if XDP is enabled.
Fixes: 86994156c7 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When the driver is in switchdev mode and rx-gro-hw is set, the RQ needs
special CQE handling. Till then, block setting of rx-gro-hw feature in
switchdev mode, to avoid failure while setting the feature due to
failure while opening the RQ.
Fixes: f97d5c2a45 ("net/mlx5e: Add handle SHAMPO cqe support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The body of mlx5e_napi_poll is wrapped into rcu_read_lock to be able to
read the XDP program pointer using rcu_dereference. However, the trap RQ
NAPI doesn't use rcu_read_lock, because the trap RQ works only in the
non-linear mode, and mlx5e_skb_from_cqe_nonlinear, until recently,
didn't support XDP and didn't call rcu_dereference.
Starting from the cited commit, mlx5e_skb_from_cqe_nonlinear supports
XDP and calls rcu_dereference, but mlx5e_trap_napi_poll doesn't wrap it
into rcu_read_lock. It leads to RCU-lockdep warnings like this:
WARNING: suspicious RCU usage
This commit fixes the issue by adding an rcu_read_lock to
mlx5e_trap_napi_poll, similarly to mlx5e_napi_poll.
Fixes: ea5d49bdae ("net/mlx5e: Add XDP multi buffer support to the non-linear legacy RQ")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When modifying TTL, packet's csum has to be recalculated.
Due to HW issue in ConnectX-5, csum recalculation for modify
TTL on RX is supported through a work-around that is specifically
enabled by configuration.
If the work-around isn't enabled, rather than adding an unsupported
action the modify TTL action on RX should be ignored.
Ignoring modify TTL action might result in zero actions, so in such
cases we will not convert the match STE to modify STE, as it is done
by FW in DMFS.
This patch fixes an issue where modify TTL action was ignored both
on RX and TX instead of only on RX.
Fixes: 4ff725e1d4 ("net/mlx5: DR, Ignore modify TTL if device doesn't support it")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In order to support multiple destination FTEs with SW steering
FW table is created with single FTE with multiple actions and
SW steering rule forward to it. When creating this table, flow
source isn't set according to the original FTE.
Fix this by passing the original FTE flow source to the created
FW table.
Fixes: 34583beea4 ("net/mlx5: DR, Create multi-destination table for SW-steering use")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Added support for adaptive IRQ coalescing. It uses net_dim
algorithm to find the suitable delay/IRQ count based on the
current packet rate.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20220517044055.876158-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following coccicheck warning:
drivers/net/ethernet/smsc/smc911x.c:483:20-22: WARNING opportunity for min()
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Link: https://lore.kernel.org/r/20220516115627.66363-1-guozhengkui@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
test_bit() tests if one bit is set or not.
Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit
QL_RESET_START (i.e. 3) is set.
In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say
QL_ADAPTER_UP.
This looks harmless, because this bit is likely be set, and when the
ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place
that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set.
This has been spotted by smatch.
Fixes: 5a4faa8737 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/80e73e33f390001d9c0140ffa9baddf6466a41a2.1652637337.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adaptive-rx and Adaptive-tx are interrupt moderation settings
that can be enabled/disabled using ethtool:
ethtool -C ethX adaptive-rx on/off adaptive-tx on/off
Unfortunately those settings are getting cleared after
changing number of queues, or in ethtool world 'channels':
ethtool -L ethX rx 1 tx 1
Clearing was happening due to introduction of bit fields
in ice_ring_container struct. This way only itr_setting
bits were rebuilt during ice_vsi_rebuild_set_coalesce().
Introduce an anonymous struct of bitfields and create a
union to refer to them as a single variable.
This way variable can be easily saved and restored.
Fixes: 61dc79ced7 ("ice: Restore interrupt throttle settings after VSI rebuild")
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The hardware statistics counters are not cleared during resets so the
drivers first access is to initialize the baseline and then subsequent
reads are for reporting the counters. The statistics counters are read
during the watchdog subtask when the interface is up. If the baseline
is not initialized before the interface is up, then there can be a brief
window in which some traffic can be transmitted/received before the
initial baseline reading takes place.
Directly initialize ethtool statistics in driver open so the baseline will
be initialized when the interface is up, and any dropped packets
incremented before the interface is up won't be reported.
Fixes: 28dc1b86f8 ("ice: ignore dropped packets during init")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do not allow to write timestamps on RX rings if PF is being configured.
When PF is being configured RX rings can be freed or rebuilt. If at the
same time timestamps are updated, the kernel will crash by dereferencing
null RX ring pointer.
PID: 1449 TASK: ff187d28ed658040 CPU: 34 COMMAND: "ice-ptp-0000:51"
#0 [ff1966a94a713bb0] machine_kexec at ffffffff9d05a0be
#1 [ff1966a94a713c08] __crash_kexec at ffffffff9d192e9d
#2 [ff1966a94a713cd0] crash_kexec at ffffffff9d1941bd
#3 [ff1966a94a713ce8] oops_end at ffffffff9d01bd54
#4 [ff1966a94a713d08] no_context at ffffffff9d06bda4
#5 [ff1966a94a713d60] __bad_area_nosemaphore at ffffffff9d06c10c
#6 [ff1966a94a713da8] do_page_fault at ffffffff9d06cae4
#7 [ff1966a94a713de0] page_fault at ffffffff9da0107e
[exception RIP: ice_ptp_update_cached_phctime+91]
RIP: ffffffffc076db8b RSP: ff1966a94a713e98 RFLAGS: 00010246
RAX: 16e3db9c6b7ccae4 RBX: ff187d269dd3c180 RCX: ff187d269cd4d018
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ff187d269cfcc644 R8: ff187d339b9641b0 R9: 0000000000000000
R10: 0000000000000002 R11: 0000000000000000 R12: ff187d269cfcc648
R13: ffffffff9f128784 R14: ffffffff9d101b70 R15: ff187d269cfcc640
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#8 [ff1966a94a713ea0] ice_ptp_periodic_work at ffffffffc076dbef [ice]
#9 [ff1966a94a713ee0] kthread_worker_fn at ffffffff9d101c1b
#10 [ff1966a94a713f10] kthread at ffffffff9d101b4d
#11 [ff1966a94a713f50] ret_from_fork at ffffffff9da0023f
Fixes: 77a781155a ("ice: enable receive hardware timestamping")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Dave Cain <dcain@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The design of INT indicator register (R_AX_PCIE_HIMR00_V1) is to reduce IO
during frequent interrupts, because it can stop chip sending interrupt to
host if we just set this indicator to 0, not all IMR(s). This indicator
register looks like a root interrupt controller of wifi chip.
However, we can't set all other IMR(s) to 0 during we are running on
interrupt service routine, or the indicator register can't reflect the
status of certain interrupt happened during this period, and then miss
some interrupts especially SER interrupt events.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-7-pkshih@realtek.com
Before 6 GHz band was supported, i.e. only 2 GHz and 5 GHz, they were the
same from the numerical point of view. However, after 6 GHz band support,
we need to do this conversion logically.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-6-pkshih@realtek.com
Update notes:
update the following to HALRF_027_00_052
TX power by rate table
TX power limit table
TX power limit RU table
TX shape table doesn't seem to be changed on HALRF_027_00_052
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-5-pkshih@realtek.com
To make user space can set TX antenna via iw command. Then, we can diagnose
antenna is connected properly or not, and measure TX power in single path.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-3-pkshih@realtek.com
When peer's NSS, rate or bandwidth is changed, we update RA(rate adaptive)
mask to ensure transmitting packets properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-2-pkshih@realtek.com
As per Errata Section 5.1, if EEE is intended to be used, some register
writes must be done once after every hardware reset. This patch now adds
the necessary register writes as listed in the Marvell errata.
Without this fix we experience ethernet problems on some of our boards
equipped with a new version of this ethernet PHY (different supplier).
The fix applies to Marvell Alaska 88E1510/88E1518/88E1512/88E1514
Rev. A0.
Signed-off-by: Leszek Polak <lpolak@arri.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <kabel@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220516070859.549170-1-sr@denx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220516082251.1651350-1-chi.minghao@zte.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220516081914.1651281-1-chi.minghao@zte.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220516072646.1651109-1-chi.minghao@zte.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In vmxnet3_rq_create(), when dma_alloc_coherent() fails,
vmxnet3_rq_destroy() is called. It sets rq->rx_ring[i].base to NULL. Then
vmxnet3_rq_create() returns an error to its callers mxnet3_rq_create_all()
-> vmxnet3_change_mtu(). Then vmxnet3_change_mtu() calls
vmxnet3_force_close() -> dev_close() in error handling code. And the driver
calls vmxnet3_close() -> vmxnet3_quiesce_dev() -> vmxnet3_rq_cleanup_all()
-> vmxnet3_rq_cleanup(). In vmxnet3_rq_cleanup(),
rq->rx_ring[ring_idx].base is accessed, but this variable is NULL, causing
a NULL pointer dereference.
To fix this possible bug, an if statement is added to check whether
rq->rx_ring[0].base is NULL in vmxnet3_rq_cleanup() and exit early if so.
The error log in our fault-injection testing is shown as follows:
[ 65.220135] BUG: kernel NULL pointer dereference, address: 0000000000000008
...
[ 65.222633] RIP: 0010:vmxnet3_rq_cleanup_all+0x396/0x4e0 [vmxnet3]
...
[ 65.227977] Call Trace:
...
[ 65.228262] vmxnet3_quiesce_dev+0x80f/0x8a0 [vmxnet3]
[ 65.228580] vmxnet3_close+0x2c4/0x3f0 [vmxnet3]
[ 65.228866] __dev_close_many+0x288/0x350
[ 65.229607] dev_close_many+0xa4/0x480
[ 65.231124] dev_close+0x138/0x230
[ 65.231933] vmxnet3_force_close+0x1f0/0x240 [vmxnet3]
[ 65.232248] vmxnet3_change_mtu+0x75d/0x920 [vmxnet3]
...
Fixes: d1a890fa37 ("net: VMware virtual Ethernet NIC driver: vmxnet3")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Zixuan Fu <r33s3n6@gmail.com>
Link: https://lore.kernel.org/r/20220514050711.2636709-1-r33s3n6@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
devm_kfree check the pointer, there is no need to check before
devm_kfree call.
This change is to cleanup the code a bit.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Link: https://lore.kernel.org/r/20220516015208.6526-1-bernard@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The following two scenarios were failing for lan966x.
1. If the port had the address X and then trying to assign the same
address, then the HW was just removing this address because first it
tries to learn new address and then delete the old one. As they are
the same the HW remove it.
2. If the port eth0 was assigned the same address as one of the other
ports eth1 then when assigning back the address to eth0 then the HW
was deleting the address of eth1.
The case 1. is fixed by checking if the port has already the same
address while case 2. is fixed by checking if the address is used by any
other port.
Fixes: e18aba8941 ("net: lan966x: add mactable support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220513180030.3076793-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmKCr/0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXbVWCAClh9ywNEPiSxXsB2k9EdVoijz0hv6I
y6YLFPfHxc8w0ewOnBxJOBeLhVjIE2K3n81NaEudheBBImWV8CGlFPHu5sI4S01b
aFcAuLT6SOat52xzkh44WGGjW517+EZM1Of1xzPhKdnR0nLvva52SpJlYwgLrkCN
O6r30cDuU558H4g2BNxavbbNFPzL7HhkBpHmgWQg4q2p7LvLuTE6sN2CvNEgUWYM
nIyK6P/FIyy3l7M7E873WhIEGNGRnAXRBEPXivRmKTlw0wizcvPxlWKm4YxTA0WL
30fw58Hy4x6SZD+7+sP0QhdjiYOofgMtZFZn/LaJYE+rfaYLsFUH3A/2
=tUrE
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.19-20220516' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-05-16
the first 2 patches are by me and target the CAN raw protocol. The 1st
removes an unneeded assignment, the other one adds support for
SO_TXTIME/SCM_TXTIME.
Oliver Hartkopp contributes 2 patches for the ISOTP protocol. The 1st
adds support for transmission without flow control, the other let's
bind() return an error on incorrect CAN ID formatting.
Geert Uytterhoeven contributes a patch to clean up ctucanfd's Kconfig
file.
Vincent Mailhol's patch for the slcan driver uses the proper function
to check for invalid CAN frames in the xmit callback.
The next patch is by Geert Uytterhoeven and makes the interrupt-names
of the renesas,rcar-canfd dt bindings mandatory.
A patch by my update the ctucanfd dt bindings to include the common
CAN controller bindings.
The last patch is by Akira Yokosawa and fixes a breakage the
ctucanfd's documentation.
* tag 'linux-can-next-for-5.19-20220516' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
docs: ctucanfd: Use 'kernel-figure' directive instead of 'figure'
dt-bindings: can: ctucanfd: include common CAN controller bindings
dt-bindings: can: renesas,rcar-canfd: Make interrupt-names required
can: slcan: slc_xmit(): use can_dropped_invalid_skb() instead of manual check
can: ctucanfd: Let users select instead of depend on CAN_CTUCANFD
can: isotp: isotp_bind(): return -EINVAL on incorrect CAN ID formatting
can: isotp: add support for transmission without flow control
can: raw: add support for SO_TXTIME/SCM_TXTIME
can: raw: raw_sendmsg(): remove not needed setting of skb->sk
====================
Link: https://lore.kernel.org/r/20220516202625.1129281-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clang randstruct gets upset when it sees struct addresspace (which is
randomized) being assigned to a struct page (which is not randomized):
drivers/net/ethernet/sun/niu.c:3385:12: error: casting from randomized structure pointer type 'struct address_space *' to 'struct page *'
*link = (struct page *) page->mapping;
^
It looks like niu.c is looking for an in-line place to chain its allocated
pages together and is overloading the "mapping" member, as it is unused.
This is very non-standard, and is expected to be cleaned up in the
future[1], but there is no "correct" way to handle it today.
No meaningful machine code changes result after this change, and source
readability is improved.
Drop the randstruct exception now that there is no "confusing" cross-type
assignment.
[1] https://lore.kernel.org/lkml/YnqgjVoMDu5v9PNG@casper.infradead.org/
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Du Cheng <ducheng2@gmail.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: William Kucharski <william.kucharski@oracle.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: linux-hardening@vger.kernel.org
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/lkml/20220511151647.7290adbe@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
skb_data_area_size() helper was used to calculate the size of the
DMA mapped buffer passed to the HW. Instead of doing this, use the
size passed to allocate the skbs.
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
slcan does a manual check in slc_xmit() to verify if the skb is valid.
This check is incomplete, use instead can_dropped_invalid_skb().
Link: https://lore.kernel.org/all/20220514141650.1109542-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CTU CAN-FD IP core is only useful when used with one of the
corresponding PCI/PCIe or platform (FPGA, SoC) drivers, which depend on
PCI resp. OF.
Hence make the users select the core driver code, instead of letting
then depend on it. Keep the core code config option visible when
compile-testing, to maintain compile-coverage.
Link: https://lore.kernel.org/all/887b7440446b6244a20a503cc6e8dc9258846706.1652104941.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Now that it is possible to use .probe without having .driver_data, let
KSZ8061 use the kszphy specific hooks for probe,suspend and resume,
which is preferred.
Switch to using the dedicated kszphy probe/suspend/resume functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-2-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, if the .probe element is present in the phy_driver structure
and the .driver_data is not, a NULL pointer dereference happens.
Allow passing .probe without .driver_data by inserting NULL checks
for priv->type.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When calling dev_fill_forward_path on a pppoe device, the provided destination
address is invalid. In order for the bridge fdb lookup to succeed, the pppoe
code needs to update ctx->daddr to the correct value.
Fix this by storing the address inside struct net_device_path_ctx
Fixes: f6efc675c9 ("net: ppp: resolve forwarding path for bridge pppoe devices")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>