In the case of an error on calling dsi_update_screen_l4(), a
successful framedone callback is still sent to panel-taal. An
error should be returned to taal_update() instead.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
TDO35S samples the data on the falling adge of the pixel clock,
therefore the data strobe should be on the raising edge.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
omapfb_mode_to_timings() sets the bpp to 0 when bootarg omapfb.mode is set to
either "pal" or "ntsc". This patch corrects this by setting the bpp to 24, as
would be done if omapdss_default_get_recommended_bpp() would be called.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move sysfs entry creation to omapfb_probe() from omapfb_create_framebuffers().
This will make sure that sysfs entry is not left behind in case of unsuccessful
probe due to failure in enabling fb0 of omapfb_create_framebuffers().
Signed-off-by: Afzal Mohammed <lazfamam@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Remove extra return statement in omapdss_default_get_recommended_bpp
from overlay.c
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
An overlay in YUV mode has to have an even input width, because data for
each pixel is divided between two adjacent pixels.
The algorithm handling manual update overlay adjusting may adjust the
overlay width to be odd.
This patch adds a check for that situation, and makes the width even.
The width is increased by one if it is possible (the unadjusted input
width is larger than the width), and decreased by one if increasing is
not possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Using bool silently converted input to 0 or 1, making the range check
useless. Use unsigned long instead, and convert to bool later. Found by
Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Unsigned regno can never be less than zero. Found by Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Unsigned rotate can never be less than zero. Found by Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Make sure NULL return value of fb2display() is not referenced. Found by
Coverity.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Skip any further processing of taal_enable_te(), taal_rotate(), and
taal_mirror() if value remains unchanged.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
OMAP DSS HW cannot send updates with odd widths. Normally the widths are
made even while preparing the update.
This patch adds a BUG_ON() to check if the update width is even. This is
to detect broken updates cleanly, as otherwise the OMAP DSS HW will just
halt, leading to obscure error situations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The current FIFO low threshold was too low, and caused the FIFO to run
empty when core domain went to INA state between FIFO fills. This patch
increases the low threshold to keep that from happening.
The threshold values depend quite much on the HW and the use cases, so
this should actually be somehow configurable from board files, perhaps.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The code presumed that all ComplexIO interrupts are errors. This is not
the case. This patch adds proper error mask for CIO interrupt handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
SMRPS function always sent BTA after sending the SMRPS packet. This is
not needed, and also caused some (buggy) panels to bug. This patch
removes the BTA.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Currently the update area on manual update displays is automatically
enlargened to fully cover scaled overlays. This patch makes that
optional, allowing the panel driver to choose if it's used or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Previously a work was started on FRAMEDONE interrupt, and this work
either sent a BTA synchronously or looped until TE_SIZE was zero, to
wait for the end of the transfer.
This patch changes a BTA to be sent asynchronously from FRAMEDONE
interrupt, and when a BTA interrupt is received, the transfer is
finished. This way we do the whole process asynchronously, and also
inside interrupt context.
This will give us much better latency to handle the end of the frame
than with the previous work based solution.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Change dsi_vc_config_l4/vp() to loop for the VC_BUSY flag to change, and
return an error if it fails.
Busy looping is bad, but there's no interrupt that can be used for all the
cases where VC can be busy. So the caller should first try to make sure
that the VC is not busy, if possible, and then call dsi_vc_config_l4/vp().
Most notable case when the caller cannot be sure if the VC is busy is
after frame has been sent. Usually DSI buffers have been emptied until we
need to reconfig the VC, but in some rare cases the VC can still be busy,
and this patch will handle that case.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Once the DSI PLL is separated from the DSI display a full DSI reset will
not be performed every time the display is enabled so the interface and
VCs must be disabled when disabling the display. If the VCs are not
disabled some register accesses will abort.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The TRM tells us to wait for the DSI PLL derived clocks to become
active before selecting them for use. I didn't actually have any issues
which this would fix but according to the TRM it seems to be the right
thing to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Print an error message if dsi_calc_clock_rates() fails just like it's
done when dispc_calc_clock_rates() fails.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Do not leave the free running pixel clock enabled if the DSI PLL reset
times out.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The OCTEON is a MIPS64 based SOC family with an on chip watchdog unit.
The driver is split into two source files one for the C code and one
for assembly. Assembly is needed to handle the NMI and then print the
machine state before the reboot is triggered.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org,
Patchwork: https://patchwork.linux-mips.org/patch/1503/
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/watchdog/octeon-wdt-main.c
create mode 100644 drivers/watchdog/octeon-wdt-nmi.S
au1000_eth uses firmware calls to get a valid MAC address, and changes
it depending on platform device id. This patch moves this logic out of
the driver into the platform device registration part, where boards with
supported chips can use whatever firmware interface they need; the default
implementation maintains compatibility with existing, YAMON-based firmware.
Tested-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1481/
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the SERIAL_8250_AU1X00 config symbol. Instead, use the MIPS_ALCHEMY
one which is always defined when building an Au1x00-based platform.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Linux-serial <linux-serial@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This one depends on a previous patch (which removes SOC_AU1X00 and changes
MACH_ALCHEMY) to apply cleanly (and then actually work), so I'd love for
this to go in via the mips tree.
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
- release_mem_region
+ release_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds HAVE_S3C2410_I2C to control inclusion of I2C bus driver
on Samsung SoCs and makes I2C bus driver dependency SoC specific instead
of machine specific. This will enalbe all machines using Samsung ARCH_S3C2410,
_S3C64XX, _S5P6440, _S5PC100, and _S5PV210 to select the I2C driver by default
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch adds HAVE_S3C_RTC to control inclusion of RTC driver for Samsung
SoCs. This option will help to include the driver only for the necessary
machines and not for any given arch.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
RTC needs to be initialized when BCD registers have invalid value.
Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
This Patch does followings.
1) Enables support for alarm and time tick pending register
for periodic interrupt generation.
2) Changes writeb to writew beacuse the macro S3C64XX_RTCCON_TICEN
(Tick Timer Enable) is 9th bit of register.
3) Changes writeb to writel as max_user_freq used in s3c64xx is 32768 and
requires 15 bits to update the Tick Count Register.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Taekgyun Ko <taeggyun.ko@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch adds UART serial port support for S5PV310.
In the case of that serial device has just one clock source, driver can not
control clock source. So add check function in get_clksrc and set_clksrc.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for the FRACVAL register on the newer UART blocks which provides
the same function as UDIVSLOT register but the FRACVAL is easier to implement.
To support UDIVSLOT register, UDIVSLOT table search is necessary though
supporting FRACVAL only needs the index value of UDIVSLOT table.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
atc_chain_complete shall be called with atchan->lock held
and bh disabled.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use {read|write}l instead of __raw_{read|write}l since PCH DMA
controller is PCI device.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
I often use "ethtool -i" command to check what driver controls the
ehternet device. But because current virtio_net driver doesn't
support "ethtool -i", it becomes the following:
# ethtool -i eth3
Cannot get driver information: Operation not supported
This patch simply adds the "ethtool -i" support. The following is the
result when using the virtio_net driver with my patch applied to.
# ethtool -i eth3
driver: virtio_net
version: N/A
firmware-version: N/A
bus-info: virtio0
Personally, "-i" is one of the most frequently-used option, and most
network drivers support "ethtool -i", so I think virtio_net also
should do.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE)
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPP channel ops structure should be const.
Cleanup the declarations to use standard C99 format.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the availablility of a sysfs device attribute for examining disk serial
numbers the ioctl is no longer needed. The user-space changes for this aren't
upstream yet so we don't have any users to worry about.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Create a new attribute for virtio-blk devices that will fetch the serial number
of the block device. This attribute can be used by udev to create disk/by-id
symlinks for devices that don't have a UUID (filesystem) associated with them.
ATA_IDENTIFY strings are special in that they can be up to 20 chars long
and aren't required to be nul-terminated. The buffer is also zero-padded
meaning that if the serial is 19 chars or less that we get a nul-terminated
string. When copying this value into a string buffer, we must be careful to
copy up to the nul (if it present) and only 20 if it is longer and not to
attempt to nul terminate; this isn't needed.
Changes since v1:
- Added BUILD_BUG_ON() for PAGE_SIZE check
- Removed min() since BUILD_BUG_ON() handles the check
- Replaced serial_sysfs() by copying id directly to buffer
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: john cooper <john.cooper@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
